In case IRQs are shared, we will not mistakenly start processing
the ring based on old status block indices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The slow path calls to the cnic driver are sleepable calls so we
cannot use rcu_read_lock(). Use mutex for these slow path calls
instead.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI drivers that implement the struct pci_error_handlers' error_detected
callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is
pci_channel_io_perm_failure. This patch fixes the issue for bnx2.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[PATCH net-next-2.6] bnx2: Update vlan_features
In order to get full use of some advanced features of BNX2, we now need to
fill dev->vlan_features.
Patch successfully tested with vlan devices built on top of bonding.
(bond0 : one bnx2 slave, one tg3 slave (not yet vlan_features enabled)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I found a little bug.
When configure in ifcfg-eth* is ONBOOT=no,
the behavior of ethtool command is wrong.
# grep ONBOOT /etc/sysconfig/network-scripts/ifcfg-eth2
ONBOOT=no
# ethtool eth2 | tail -n1
Link detected: yes
I think "Link detected" should be "no".
Signed-off-by: Ooiwa Naohiro <nooiwa@miraclelinux.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is inspired by patch recently posted by Johannes Berg. Basically what
my patch does is to group list and a count of addresses into newly introduced
structure netdev_hw_addr_list. This brings us two benefits:
1) struct net_device becames a bit nicer.
2) in the future there will be a possibility to operate with lists independently
on netdevices (with exporting right functions).
I wanted to introduce this patch before I'll post a multicast lists conversion.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 4 +-
drivers/net/e1000/e1000_main.c | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/mv643xx_eth.c | 2 +-
drivers/net/niu.c | 4 +-
drivers/net/virtio_net.c | 10 ++--
drivers/s390/net/qeth_l2_main.c | 2 +-
include/linux/netdevice.h | 17 +++--
net/core/dev.c | 130 ++++++++++++++++++--------------------
9 files changed, 89 insertions(+), 90 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Add interface and functions to support a new CNIC driver to drive
the Broadcom bnx2 hardware for iSCSI offload.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is no need to check if a pointer is NULL before calling
vfree(), since vfree() function already check for it.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_dma_unmap() is quite expensive for small packets,
because we use two different cache lines from skb_shared_info.
One to access nr_frags, one to access dma_maps[0]
Instead of dma_maps being an array of MAX_SKB_FRAGS + 1 elements,
let dma_head alone in a new dma_head field, close to nr_frags,
to reduce cache lines misses.
Tested on my dev machine (bnx2 & tg3 adapters), nice speedup !
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).
I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.
The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 13 +--
drivers/net/e1000/e1000_main.c | 24 +++--
drivers/net/ixgbe/ixgbe_common.c | 14 ++--
drivers/net/ixgbe/ixgbe_common.h | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/ixgbe/ixgbe_type.h | 4 +-
drivers/net/macvlan.c | 11 +-
drivers/net/mv643xx_eth.c | 11 +-
drivers/net/niu.c | 7 +-
drivers/net/virtio_net.c | 7 +-
drivers/s390/net/qeth_l2_main.c | 6 +-
drivers/scsi/fcoe/fcoe.c | 16 ++--
include/linux/netdevice.h | 18 ++--
net/8021q/vlan.c | 4 +-
net/8021q/vlan_dev.c | 10 +-
net/core/dev.c | 195 +++++++++++++++++++++++++++-----------
net/dsa/slave.c | 10 +-
net/packet/af_packet.c | 4 +-
18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using bnx2 in a high transmit load, bnx2_tx_int() cost is pretty high.
There are two reasons.
One is an expensive call to bnx2_get_hw_tx_cons(bnapi) for each freed skb
One is cpu stalls when accessing skb_is_gso(skb) / skb_shinfo(skb)->nr_frags
because of two cache line misses.
(One to get skb->end/head to compute skb_shinfo(skb),
one to get is_gso/nr_frags)
This patch :
1) avoids calling bnx2_get_hw_tx_cons(bnapi) too many times.
2) makes bnx2_start_xmit() cache is_gso & nr_frags into sw_tx_bd descriptor.
This uses a litle bit more ram (256 longs per device on x86), but helps a lot.
3) uses a prefetch(&skb->end) to speedup dev_kfree_skb(), bringing
cache line that will be needed in skb_release_data()
result is 5 % bandwidth increase in benchmarks, involving UDP or TCP receive
& transmits, when a cpu is dedicated to ksoftirqd for bnx2.
bnx2_tx_int going from 3.33 % cpu to 0.5 % cpu in oprofile
Note : skb_dma_unmap() still very expensive but this is for another patch,
not related to bnx2 (2.9 % of cpu, while it does nothing on x86_32)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add barrier() to bnx2_get_hw_{tx|rx}_cons() to fix this issue:
http://bugzilla.kernel.org/show_bug.cgi?id=12698
This issue was reported by multiple i386 users. Without barrier(),
the compiled code looks like the following where %eax contains the
address of the tx_cons or rx_cons in the DMA status block. The
status block contents can change between the cmpb and the movzwl
instruction. The driver would crash if the value was not 0xff during
the cmpb instruction, but changed to 0xff during the movzwl
instruction.
6828: 80 38 ff cmpb $0xff,(%eax)
682b: 0f b7 10 movzwl (%eax),%edx
With the added barrier(), the compiled code now looks correct:
683d: 0f b7 10 movzwl (%eax),%edx
6840: 0f b6 c2 movzbl %dl,%eax
6843: 3d ff 00 00 00 cmp $0xff,%eax
Thanks to Pascal de Bruijn <pmjdebruijn@pcode.nl> for reporting the
problem and Holger Noefer <hnoefer@pironet-ndh.com> for patiently
testing test patches for us.
Also updated version to 2.0.1.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mips identifier is reserved by gcc on mips plattforms. Don't use it
in the code.
Signed-off-by: Bastian Blank <waldi@debian.org>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_40BIT_MASK macro with DMA_BIT_MASK(40)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on original patch by Ben Hutchings <ben@decadent.org.uk> and
Bastian Blank <waldi@debian.org>, with the following main changes:
Separated the mips firmware and rv2p firmware into different files
to make it easier to update them separately.
Added some code to fixup the rv2p code with run-time information
such as PAGE_SIZE.
Update version to 2.0.0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSI-X handler was chosen before the call to pci_enable_msix().
If MSI-X was not available, the wrong MSI-X handler would be used in
INTA mode. This would cause a screaming interrupt problem because
INTA would not be cleared by the MSI-X handler.
Fixed by assigning MSI-X handler after pci_enable_msix() returns
successfully. Also update version to 1.9.3.
Thomas Chenault <thomas_chenault@dell.com> helped us find this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If errors are reported on a frame descriptor, we need to
account for the buffer pages that may have been used for this
error packet and recycle them. Otherwise, we may get the wrong
pages for the next packet.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the locking is OK as the locks were being taken before the
various phy setup functions, add the annotations as they release and
reacquire the phy_lock.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA memory for the jumbo rx page rings was freed incorrectly using the
wrong local variable as the array index.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And fix the 5716S pci_device_id entry to point to the proper string.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change MSI-X vector names to "ethx-%d".
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2 chips do not support per MSI vector masking. On 5706/5708, new MSI
address/data are stored only when the MSI enable bit is toggled. As a result,
SMP affinity no longer works in the latest kernel. A more serious problem is
that the driver will no longer receive interrupts when the MSI receiving CPU
goes offline.
The workaround in this patch only addresses the problem of CPU going offline.
When that happens, the driver's timer function will detect that it is making
no forward progress on pending interrupt events and will recover from it.
Eric Dumazet reported the problem.
We also found that if an interrupt is internally asserted while MSI and INTA
are disabled, the chip will end up in the same state after MSI is re-enabled.
The same workaround is needed for this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Tested-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert driver to new net_device_ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bnx2 so that netpoll works properly. Specifically:
1) Fix parameters to bnx2_interrupt to be a struct bnx2_napi rather than a
struct net_device
2) Fix poll_controller method to check every queue in the rx case so frames
aren't missed
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all related timeout constants to the same location. BNX2
prefix is also added to make them more consistent.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default rx buffer water marks for XOFF/XON are for 1500 MTU. At
larger MTUs, these water marks need to be adjusted for effective
flow control.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some quad-port cards that cannot support WoL on all ports due
to excessive power consumption, the driver needs to restrict WoL
on some ports by checking VAUX_PRESET bit.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before, the driver would not care about the return codes from pci_map_*
functions. This could be potentially dangerous if a mapping failed.
Now, we will check all pci_map_* calls. On the transmit side, we switch
to use the new function skb_dma_map(). On the receive side, we add
pci_dma_mapping_error().
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to check netif_running() state in most ethtool operations
and properly handle the !netif_running() state where the chip is
in an uninitailzed state or low power state that may not accept
any MMIO.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This logic is used in bnx2_close() and bnx2_suspend() and
so should be separated out into a separate function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timer_interval field is only assigned once, and never reassigned.
We can safely replace all instances of the timer_interval with a
constant value.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name of the board is only used during the initialization of
the adapter. We can save the space of a pointer by not storing
this information.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2_set_mac_link() doesn't need to return any error codes. And
all the callers don't check the return code. It is safe to
change the return type to a void.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain cases when ASF or other management firmware is running, the
chip may be configured to always strip out the VLAN tag even when
VLAN acceleration is not enabled. This causes some VLAN tagged
packets to be received by the host stack without any knowledge that
the original packet was VLAN tagged.
We fix this by re-inserting the VLAN tag into the packet when necessary.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should now be checking BNX2_FLAG_CAN_KEEP_VLAN to determine how
to set the VLAN rx tagging in the RX_MODE register.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will fix the following sparse warnings:
/home/benli/sparse/bnx2.c:297:8: warning: symbol 'val' shadows an earlier one
/home/benli/sparse/bnx2.c:286:60: originally declared here
/home/benli/sparse/bnx2.c:7461:7: warning: symbol 'i' shadows an earlier one
/home/benli/sparse/bnx2.c:7265:10: originally declared here
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring secondary unicast addresses. There
are 4 additional perfect match filters which can be used for
secondary unicast address support.
* Modified bnx2_set_mac_addr() to be more generic in handling
the setting of the perfect match filters
* Changed bnx2_set_rx_mode() to handle the unicast dev_addr_list
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Negotiate with boot code and ASF firmware to see if it can
support keeping VLAN tags in the RX packets. If supported
by firmware, the VLAN tag will be kept in the RX packet
unless VLAN acceleration is registered.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ack=1 means wait for firmware acknowledgement, and ack=0
means don't wait. All current callers will set it to 1.
In the next patch, new calls will set ack=0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device may be in D3-hot state and may crash if we try to
configure the speed settings by accessing the registers.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And update module description.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All error handling in bnx2_open() can be consolidated.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable multiple rx rings if MSI-X vectors are available. We enable
up to 7 rx rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the same MSI-X handler to schedule NAPI. Change the dev_instance
void pointer to the bnx2_napi struct instead so we can have the proper
context for each MSI-X vector.
Add a new bnx2_poll_msix() that is optimized for handling MSI-X
NAPI polling of rx/tx work only. Remove the old bnx2_tx_poll() that
is no longer needed. Each MSI-X vector handles 1 tx and 1 rx ring.
The first vector handles link events as well.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hw_tx_cons_ptr and hw_rx_cons_ptr to speed up the retreival of
the tx and rx consumer index, since the MSI-X and default status
blocks have different structures.
Combine status_blk and status_blk_msix into a union. We'll only use
one type of status block for each vector.
Separate the code to detect more rx and tx work from the code to
detect link related work.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for multi-ring support, rx ring variables are now put
in a separate bnx2_rx_ring_info struct. With MSI-X, we can support
multiple rx rings.
The functions to allocate/free rx memory and to initialize rx rings
are now modified to handle multiple rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for multi-ring support, tx ring variables are now put
in a separate bnx2_tx_ring_info struct. Multi tx ring will not be
enabled until it is fully supported by the stack. Only 1 tx ring
will be used at the moment.
The functions to allocate/free tx memory and to initialize tx rings
are now modified to handle multiple rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the RTNL is held when we invoke flush_scheduled_work() we could
deadlock. One such case is linkwatch, it is a work struct which tries
to grab the RTNL semaphore.
The most common case are net driver ->stop() methods. The
simplest conversion is to instead use cancel_{delayed_}work_sync()
explicitly on the various work struct the driver uses.
This is an OK transformation because these work structs are doing
things like resetting the chip, restarting link negotiation, and so
forth. And if we're bringing down the device, we're about to turn the
chip off and reset it anways. So if we cancel a pending work event,
that's fine here.
Some drivers were working around this deadlock by using a msleep()
polling loop of some sort, and those cases are converted to instead
use cancel_{delayed_}work_sync() as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of assigning values for the struct cpu_reg's at runtime,
we already know these values at compile time. Therefore, we can use
designated initializers, to initialize these structures and not have
to incur this assignment cost at run-time.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make the bnx2 code more consistent, all instances of
RX_COPY_THRESH have been changed to BNX2_RX_COPY_THRESH.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_offset field is set to a constant value and initialized
only once. By replacing all references to the rx_offset field,
we can eliminate rx_offset from the bnx2 structure. This will
save 4 bytes for every bnx2 instance.
[Added parentheses to the definition of BNX2_RX_OFFSET, as noted
by Ben Hutchings.]
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCI recovery functions to the driver. The initial pci state is
also saved so the the MSI state can be restored during PCI recovery.
Signed-off-by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Gospodarek <andy@greyhouse.net> found that netconsole would
panic when resetting bnx2 devices.
>From Andy:
"The issue is the bnx2_set_link in bnx2_init_nic will print a link-status
message before we are fully initialized and ready to start polling.
Polling is currently disabled in this state, but since the
__LINK_STATE_RX_SCHED is overloaded to not only try and disable polling
but also to make the system aware there is something waiting to be
polled, we really have to fix this in drivers.
The problematic call is the one to netif_rx_complete as it tries to
remove an entry from the poll_list when there isn't one."
While this netconsole problem should be fixed separately, we really
should not reset the PHY when changing ring sizes, MTU, or other
similar settings. The PHY reset causes several seconds of unnecessary
link disruptions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new RV2P firmware fixes 2 issues:
1. The jumbo rx buffer page size is now configurable and set to the
proper PAGE_SIZE. Before, it was assumed to be always 4K.
2. Driver sometimes would crash when receiving jumbo packets mixed
with firmware management packets. This was caused by the old
firmware DMA'ing to the wrong address.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should zero out the context memory for 5709 before each reset. When
we resume after suspend for example, the memory may not be zero and the
chip may not function correctly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register BNX2_CTX_STATUS (0x1004) should be skipped on 5709 as it
contains reserved bits.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some remote PHY blade systems, the driver receives no initial link
interrupt. As a result, the GMII/MII MAC mode does not get setup properly.
To fix this problem, we add an initial poll of the link state after chip
reset.
With this change, the setting of the initial carrier state in the init
code can be eliminated.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2_set_remote_link() should be called under bp->phy_lock to protect
against concurrent polling and interrupt calls. This change is needed
by the next patch which will add one initial poll of the remote PHY
link status.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of some board issues, we need to disable parallel detect on
an HP blade. Without this patch, the link state can become stuck
when it goes into parallel detect mode.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patches to workaround the 5706S on an HP blade were not
sufficient. The link state still does not change properly in some
cases. This patch adds polling to make it completely reliable.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/bnx2.c:67: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were checking for the ASYM_PAUSE bit for 1000Base-X twice instead
checking for both the 1000Base-X bit and the 10/100/1000Base-T bit.
The purpose of the logic is to tell the firmware that ASYM_PAUSE is
set on either the Serdes or Copper interface.
Problem was discovered by Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the programmable high/low water marks in 5709 for
802.3 flow control.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CTX_WR macro is unnecessary and obfuscates the code.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The REG_WR_IND/REG_RD_IND macros are unnecessary and obfuscate the
code. Many callers to these macros read and write shared memory from
the bp->shmem_base, so we add 2 similar functions that automatically
add the shared memory base.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the tx coalescing setup code independent of the MSIX vector.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Correct the MII expansion serdes control register definition.
2. Check an additional RUDI_INVALID bit when determining 5706S link.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix "bp->phy_flags" names with BNX2_PHY_FLAG_* for consistency.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some blade systems using the 5706 serdes, the hardware sometimes
does not properly generate link down interrupts. We add a workaround
in the driver's timer to force a link-down when some PHY registers
report loss of SYNC.
The parallel detect logic is cleaned up slightly to better integrate
the workaround.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is more correct to get the status block from the bnx2_napi struct
instead of the bnx2 struct. It happens that they are the same in this
case because we are using the first MSIX vector.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip has problem running in this mode and needs to be disabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change bnx2_init_napi() to void.
Warning was noted by DaveM.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable new tx ring and add new MSIX handler and NAPI poll function
for the new tx ring. Enable MSIX when the hardware supports it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To separate TX IRQs into a different MSIX vector, we need to
support a new tx ring. The original tx ring will still be used
when not using MSIX.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change bnx2_napi struct into an array and add code to manage multiple
IRQs. MSIX hardware structures and new registers are also added.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx related fields used in NAPI polling are moved from the main
bnx2 struct to the bnx2_napi struct.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx related fields used in NAPI polling are moved from the main
bnx2 struct to the bnx2_napi struct.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a bnx2_napi structure that will hold a napi_struct and
other fields to handle NAPI polling for the napi_struct. Various tx
and rx indexes and status block pointers will be moved from the main
bnx2 structure to this bnx2_napi structure.
Most NAPI path functions are modified to be passed this bnx2_napi
struct pointer.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a table to keep track of multiple IRQs and restructure the IRQ
request and free functions so that they can be easily expanded to
handle multiple IRQs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the code cleaner and easier to support different tx rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the MTU requires more than 1 page for the SKB, enable the page ring
and calculate the size of the page ring. This will guarantee order-0
allocation regardless of the MTU size.
Fixup loopback test packet size so that we don't deal with the pages
during loopback test.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function to reuse a page in case of allocation or other errors.
Add code to construct the completed SKB with the additional data in
the pages.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new fields to keep track of the pages and the page rings.
Add functions to allocate and free pages.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the common functions that will be used to initialize the
normal RX rings and the page rings.
Change the copybreak constant RX_COPY_THRESH to 128. This same
constant will be used for the max. size of the linear SKB when pages
are used. Copybreak will be turned off when pages are used.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function to handle new SKB allocation and to prepare the
completed SKB. This makes it easier to add support for non-linear
SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the various ring constants to make the code cleaner.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets can be left in the RX ring if the NAPI budget is reached.
This is caused by storing the latest rx index at the beginning of
bnx2_rx_int(). We may not process all the work up to this index
if the budget is reached and so some packets in the RX ring may rot
when we later check for more work using this stored rx index.
The fix is to not store this latest hw index and only store the
processed rx index. We use a new function bnx2_get_hw_rx_cons()
to fetch the latest hw rx index.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove asm/bitops.h includes
including asm/bitops directly may cause compile errors. don't include it
and include linux/bitops instead. next patch will deny including asm header
directly.
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (51 commits)
[IPV6]: Fix again the fl6_sock_lookup() fixed locking
[NETFILTER]: nf_conntrack_tcp: fix connection reopening fix
[IPV6]: Fix race in ipv6_flowlabel_opt() when inserting two labels
[IPV6]: Lost locking in fl6_sock_lookup
[IPV6]: Lost locking when inserting a flowlabel in ipv6_fl_list
[NETFILTER]: xt_sctp: fix mistake to pass a pointer where array is required
[NET]: Fix OOPS due to missing check in dev_parse_header().
[TCP]: Remove lost_retrans zero seqno special cases
[NET]: fix carrier-on bug?
[NET]: Fix uninitialised variable in ip_frag_reasm()
[IPSEC]: Rename mode to outer_mode and add inner_mode
[IPSEC]: Disallow combinations of RO and AH/ESP/IPCOMP
[IPSEC]: Use the top IPv4 route's peer instead of the bottom
[IPSEC]: Store afinfo pointer in xfrm_mode
[IPSEC]: Add missing BEET checks
[IPSEC]: Move type and mode map into xfrm_state.c
[IPSEC]: Fix length check in xfrm_parse_spi
[IPSEC]: Move ip_summed zapping out of xfrm6_rcv_spi
[IPSEC]: Get nexthdr from caller in xfrm6_rcv_spi
[IPSEC]: Move tunnel parsing for IPv4 out of xfrm4_input
...
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The bug is in the code in bnx2_set_power_state() that assumes copper
devices when setting up WoL. This is no longer true after adding WoL
support for Serdes devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to read and store sblk->status_idx before checking for more work.
The status idx is later written back to the hardware when enabling
interrupts to acknowledge how much work has been processed. If the
order is reversed, we can end up acknowledging work we haven't
processed.
When completing bnx2_poll(), we should always break out of the while
loop and return work_done instead of returning 0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the list handling in net_rx_action() to be
correct, drivers must follow certain rules as stated by
this comment in net_rx_action():
/* Drivers must not modify the NAPI state if they
* consume the entire weight. In such cases this code
* still "owns" the NAPI instance and therefore can
* move the instance around on the list at-will.
*/
A few drivers do not do this because they mix the budget checks
with reading hardware state, resulting in crashes like the one
reported by takano@axe-inc.co.jp.
BNX2 and TG3 are taken care of here, SKY2 fix is from Stephen
Hemminger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the default WoL setting to match the NVRAM's setting. It
always defaulted to WoL disabled before and caused a lot of confusion
for users.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remote PHY media type and link status can change between
->probe() and ->open(). For correct operation, we need to get the
new status again during ->open().
The ethtool link test and loopback test are also fixed to work with
remote PHY. PHY loopback is simply skipped when remote PHY is
present.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a follow up to the patches from Denys Vlasenkos
<vda.linux@googlemail.com> to further optimize firmware loading.
1. In bnx2_init_cpus(), we allocate memory for decompression once
and use it repeatedly instead of doing this for every firmware image.
2. We eliminate the BSS and SBSS firmware sections in bnx2_fw*.h since
these are always zeros.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies gzip unpacking code in bnx2 driver so that
it does not depend on bnx2 internals. I will move this code
out of the driver and into zlib in follow-on patch.
It can be useful in other drivers which need to store firmwares
or any other relatively big binary blobs - fonts, cursor bitmaps,
whatever.
Patch is run tested by Michael Chan (driver author).
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the operations
get-tx-csum
get-sg
get-tso
get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.
This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.
The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case. Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.
[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.
In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.
The signature of the ->poll() call back goes from:
int foo_poll(struct net_device *dev, int *budget)
to
int foo_poll(struct napi_struct *napi, int budget)
The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract). The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.
The napi_struct is to be embedded in the device driver private data
structures.
Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler. Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.
With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.
Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.
[ Ported to current tree and all drivers converted. Integrated
Stephen's follow-on kerneldoc additions, and restored poll_list
handling to the old style to fix mutual exclusion issues. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
