nlh is being checked for validtity two times when it is dereferenced in
this function. Check for validity again when updating the flags through
nlh pointer to make the dereferencing safe.
CC: <stable@vger.kernel.org>
Addresses-Coverity: ("NULL pointer dereference")
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Blumenstingl says:
====================
lantiq: GSWIP: two more fixes
after my last patch got accepted and is now in net as commit
3e6fdeb28f ("net: dsa: lantiq_gswip: Let GSWIP automatically set
the xMII clock") [0] some more people from the OpenWrt community
(many thanks to everyone involved) helped test the GSWIP driver: [1]
It turns out that the previous fix does not work for all boards.
There's no regression, but it doesn't fix as many problems as I
thought. This is why two more fixes are needed:
- the first one solves many (four known but probably there are
a few extra hidden ones) reported bugs with the GSWIP where no
traffic would flow. Not all circumstances are fully understood
but testing shows that switching away from PHY auto polling
solves all of them
- while investigating the different problems which are addressed
by the first patch some small issues with the existing code were
found. These are addressed by the second patch
Changes since v1 at [0]:
- Don't configure the link parameters in gswip_phylink_mac_config
(as we're using the "modern" way in gswip_phylink_mac_link_up).
Thanks to Andrew for the hint with the phylink documentation.
- Clarify that GSWIP_MII_CFG_RMII_CLK is ignored by the hardware in
the description of the second patch as suggested by Hauke
- Don't set GSWIP_MII_CFG_RGMII_IBS in the second patch as we don't
have any hardware available for testing this. The patch
description now also reflects this.
- Added Andrew's Reviewed-by to the first patch (thank you!)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few more bits in the GSWIP_MII_CFG register for which we
did rely on the boot-loader (or the hardware defaults) to set them up
properly.
For some external RMII PHYs we need to select the GSWIP_MII_CFG_RMII_CLK
bit and also we should un-set it for non-RMII PHYs. The
GSWIP_MII_CFG_RMII_CLK bit is ignored for other PHY connection modes.
The GSWIP IP also supports in-band auto-negotiation for RGMII PHYs when
the GSWIP_MII_CFG_RGMII_IBS bit is set. Clear this bit always as there's
no known hardware which uses this (so it is not tested yet).
Clear the xMII isolation bit when set at initialization time if it was
previously set by the bootloader. Not doing so could lead to no traffic
(neither RX nor TX) on a port with this bit set.
While here, also add the GSWIP_MII_CFG_RESET bit. We don't need to
manage it because this bit is self-clearning when set. We still add it
here to get a better overview of the GSWIP_MII_CFG register.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY auto polling on the GSWIP hardware can be used so link changes
(speed, link up/down, etc.) can be detected automatically. Internally
GSWIP reads the PHY's registers for this functionality. Based on this
automatic detection GSWIP can also automatically re-configure it's port
settings. Unfortunately this auto polling (and configuration) mechanism
seems to cause various issues observed by different people on different
devices:
- FritzBox 7360v2: the two Gbit/s ports (connected to the two internal
PHY11G instances) are working fine but the two Fast Ethernet ports
(using an AR8030 RMII PHY) are completely dead (neither RX nor TX are
received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit
as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This
makes the PHY auto polling state machine (rightfully?) think that the
established link speed (when the other side is Gbit/s capable) is
1Gbit/s.
- None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are
connected to the internal PHY11G GPHYs while the other three are
external RGMII PHYs) are working. Neither RX nor TX traffic was
observed. It is not clear which part of the PHY auto polling state-
machine caused this.
- FritzBox 7412 (only one LAN port which is connected to one of the
internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing
random disconnects (link down events could be seen). Sometimes all
traffic would stop after such disconnect. It is not clear which part
of the PHY auto polling state-machine cauased this.
- TP-Link TD-W9980 (two ports are connected to the internal GPHYs
running in PHY11G / Gbit/s mode, the other two are external RGMII
PHYs) was affected by similar issues as the FritzBox 7412 just without
the "link down" events
Switch to software based configuration instead of PHY auto polling (and
letting the GSWIP hardware configure the ports automatically) for the
following link parameters:
- link up/down
- link speed
- full/half duplex
- flow control (RX / TX pause)
After a big round of manual testing by various people (who helped test
this on OpenWrt) it turns out that this fixes all reported issues.
Additionally it can be considered more future proof because any
"quirk" which is implemented for a PHY on the driver side can now be
used with the GSWIP hardware as well because Linux is in control of the
link parameters.
As a nice side-effect this also solves a problem where fixed-links were
not supported previously because we were relying on the PHY auto polling
mechanism, which cannot work for fixed-links as there's no PHY from
where it can read the registers. Configuring the link settings on the
GSWIP ports means that we now use the settings from device-tree also for
ports with fixed-links.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Fixes: 3e6fdeb28f ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock")
Cc: stable@vger.kernel.org
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several bug fixes:
- Regression from the last pull request in cxgb4 related to the ipv6 fixes
- KASAN crasher in rtrs
- oops in hfi1 related to a buggy BIOS
- Userspace could oops qedr's XRC support
- Uninitialized memory when parsing a LS_NLA_TYPE_DGID netlink message
-----BEGIN PGP SIGNATURE-----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=UaHF
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Nothing very exciting here, just a few small bug fixes. No red flags
for this release have shown up.
- Regression from the last pull request in cxgb4 related to the ipv6
fixes
- KASAN crasher in rtrs
- oops in hfi1 related to a buggy BIOS
- Userspace could oops qedr's XRC support
- Uninitialized memory when parsing a LS_NLA_TYPE_DGID netlink
message"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/addr: Be strict with gid size
RDMA/qedr: Fix kernel panic when trying to access recv_cq
IB/hfi1: Fix probe time panic when AIP is enabled with a buggy BIOS
RDMA/cxgb4: check for ipv6 address properly while destroying listener
RDMA/rtrs-clt: Close rtrs client conn before destroying rtrs clt session files
The Devicetree standard specifies an 8 byte alignment of the FDT.
Code in libfdt expects this alignment for an FDT image in memory.
kmemdup() returns 4 byte alignment on openrisc. Replace kmemdup()
with kmalloc(), align pointer, memcpy() to get proper alignment.
The 4 byte alignment exposed a related bug which triggered a crash
on openrisc with:
commit 79edff1206 ("scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9")
as reported in:
https://lore.kernel.org/lkml/20210327224116.69309-1-linux@roeck-us.net/
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Link: https://lore.kernel.org/r/20210408204508.2276230-1-frowand.list@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-04-08
This series contains updates to i40e and ice drivers.
Grzegorz fixes the ordering of parameters to i40e_aq_get_phy_register()
which is causing incorrect information to be reported.
Arkadiusz fixes various sparse issues reported on the i40e driver.
Yongxin Liu fixes a memory leak with aRFS following resume from suspend
for ice driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2021-04-08
The following pull-request contains BPF updates for your *net* tree.
We've added 4 non-merge commits during the last 2 day(s) which contain
a total of 4 files changed, 31 insertions(+), 10 deletions(-).
The main changes are:
1) Validate and reject invalid JIT branch displacements, from Piotr Krysiuk.
2) Fix incorrect unhash restore as well as fwd_alloc memory accounting in
sock map, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* S1G beacon validation
* potential leak in nl80211
* fast-RX confusion with 4-addr mode
* erroneous WARN_ON that userspace can trigger
* wrong time units in virt_wifi
* rfkill userspace API breakage
* TXQ AC confusing that led to traffic stopped forever
* connection monitoring time after/before confusion
* netlink beacon head validation buffer overrun
-----BEGIN PGP SIGNATURE-----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=rGEc
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2021-04-08.2' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes berg says:
====================
Various small fixes:
* S1G beacon validation
* potential leak in nl80211
* fast-RX confusion with 4-addr mode
* erroneous WARN_ON that userspace can trigger
* wrong time units in virt_wifi
* rfkill userspace API breakage
* TXQ AC confusing that led to traffic stopped forever
* connection monitoring time after/before confusion
* netlink beacon head validation buffer overrun
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting iftoken can fail for several different reasons but there
and there was no report to user as to the cause. Add netlink
extended errors to the processing of the request.
This requires adding additional argument through rtnl_af_ops
set_link_af callback.
Reported-by: Hongren Zheng <li@zenithal.me>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov says:
====================
Action initalization fixes
This series fixes reference counting of action instances and modules in
several parts of action init code. The first patch reverts previous fix
that didn't properly account for rollback from a failure in the middle of
the loop in tcf_action_init() which is properly fixed by the following
patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With recent changes that separated action module load from action
initialization tcf_action_init() function error handling code was modified
to manually release the loaded modules if loading/initialization of any
further action in same batch failed. For the case when all modules
successfully loaded and some of the actions were initialized before one of
them failed in init handler. In this case for all previous actions the
module will be released twice by the error handler: First time by the loop
that manually calls module_put() for all ops, and second time by the action
destroy code that puts the module after destroying the action.
Reproduction:
$ sudo tc actions add action simple sdata \"2\" index 2
$ sudo tc actions add action simple sdata \"1\" index 1 \
action simple sdata \"2\" index 2
RTNETLINK answers: File exists
We have an error talking to the kernel
$ sudo tc actions ls action simple
total acts 1
action order 0: Simple <"2">
index 2 ref 1 bind 0
$ sudo tc actions flush action simple
$ sudo tc actions ls action simple
$ sudo tc actions add action simple sdata \"2\" index 2
Error: Failed to load TC action module.
We have an error talking to the kernel
$ lsmod | grep simple
act_simple 20480 -1
Fix the issue by modifying module reference counting handling in action
initialization code:
- Get module reference in tcf_idr_create() and put it in tcf_idr_release()
instead of taking over the reference held by the caller.
- Modify users of tcf_action_init_1() to always release the module
reference which they obtain before calling init function instead of
assuming that created action takes over the reference.
- Finally, modify tcf_action_init_1() to not release the module reference
when overwriting existing action as this is no longer necessary since both
upper and lower layers obtain and manage their own module references
independently.
Fixes: d349f99768 ("net_sched: fix RTNL deadlock again caused by request_module()")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Action init code increments reference counter when it changes an action.
This is the desired behavior for cls API which needs to obtain action
reference for every classifier that points to action. However, act API just
needs to change the action and releases the reference before returning.
This sequence breaks when the requested action doesn't exist, which causes
act API init code to create new action with specified index, but action is
still released before returning and is deleted (unless it was referenced
concurrently by cls API).
Reproduction:
$ sudo tc actions ls action gact
$ sudo tc actions change action gact drop index 1
$ sudo tc actions ls action gact
Extend tcf_action_init() to accept 'init_res' array and initialize it with
action->ops->init() result. In tcf_action_add() remove pointers to created
actions from actions array before passing it to tcf_action_put_many().
Fixes: cae422f379 ("net: sched: use reference counting action init")
Reported-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6855e8213e.
Following commit in series fixes the issue without introducing regression
in error rollback of tcf_action_destroy().
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I removed myself as a maintainer of the yaml file, I missed that
some maintainer is required. Oleksij is already listed in MAINTAINERS
for this file, so add him here as well.
Fixes: 1ae6b37808 ("i2c: imx: drop me as maintainer of binding docs")
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
WARNING: CPU: 5 PID: 227 at fs/io_uring.c:8578 io_ring_exit_work+0xe6/0x470
RIP: 0010:io_ring_exit_work+0xe6/0x470
Call Trace:
process_one_work+0x206/0x400
worker_thread+0x4a/0x3d0
kthread+0x129/0x170
ret_from_fork+0x22/0x30
INFO: task lfs-openat:2359 blocked for more than 245 seconds.
task:lfs-openat state:D stack: 0 pid: 2359 ppid: 1 flags:0x00000004
Call Trace:
...
wait_for_completion+0x8b/0xf0
io_wq_destroy_manager+0x24/0x60
io_wq_put_and_exit+0x18/0x30
io_uring_clean_tctx+0x76/0xa0
__io_uring_files_cancel+0x1b9/0x2e0
do_exit+0xc0/0xb40
...
Even after io-wq destroy has been issued io-wq worker threads will
continue executing all left work items as usual, and may hang waiting
for I/O that won't ever complete (aka unbounded).
[<0>] pipe_read+0x306/0x450
[<0>] io_iter_do_read+0x1e/0x40
[<0>] io_read+0xd5/0x330
[<0>] io_issue_sqe+0xd21/0x18a0
[<0>] io_wq_submit_work+0x6c/0x140
[<0>] io_worker_handle_work+0x17d/0x400
[<0>] io_wqe_worker+0x2c0/0x330
[<0>] ret_from_fork+0x22/0x30
Cancel all unbounded I/O instead of executing them. This changes the
user visible behaviour, but that's inevitable as io-wq is not per task.
Suggested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/cd4b543154154cba055cf86f351441c2174d7f71.1617842918.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
WARNING: at fs/io_uring.c:8578 io_ring_exit_work.cold+0x0/0x18
As reissuing is now passed back by REQ_F_REISSUE and kiocb_done()
internally uses __io_complete_rw(), it may stop after setting the flag
so leaving a dangling request.
There are tricky edge cases, e.g. reading beyound file, boundary, so
the easiest way is to hand code reissue in kiocb_done() as
__io_complete_rw() was doing for us before.
Fixes: 230d50d448 ("io_uring: move reissue into regular IO path")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/f602250d292f8a84cca9a01d747744d1e797be26.1617842918.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The nla_len() is less than or equal to 16. If it's less than 16 then end
of the "gid" buffer is uninitialized.
Fixes: ae43f82867 ("IB/core: Add IP to GID netlink offload")
Link: https://lore.kernel.org/r/20210405074434.264221-1-leon@kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
- fix incorrect dereference of the ext_params2 external interrupt parameter,
which leads to an instant kernel crash if a pfault interrupt occurs.
- add forgotten stack unwinder support, and fix memory leak for the new
machine check handler stack.
- fix inline assembly register clobbering due to KASAN code instrumentation.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEECMNfWEw3SLnmiLkZIg7DeRspbsIFAmBvPqEACgkQIg7DeRsp
bsJc5A/8Ca/l7PfcrSkymp2Nr5tldUNYGdNT56a+Eavq2QgTOxJM0zXm/hRP1QzH
MM6yIb2MhCYplyXkPt1qs7QYfnWpCvnzywMCPeiSbNQ2Fk4h1zMdaLFR5t/aWoKv
vYJH1XMtFUHhPzeg3mJDr4vAYZZaQyVLutM3OVrkANavLoKwv1Yo6KMFuLIRZTYW
9PeTNScl8fOIcDX18UjUdcZH6cBf51OHoGnIQWXeZSZoDMPxHMeweogskyzuECyD
nk2ZRJLcsCvEUbkECRr1AEDMV3wDIpxIaRXNM5I08UlhI8gGZqcNp+P/OqrnE5dP
VKFJuXsMyJVdeIijLwd/debPinuC9Yq9N2V312SwfiK8zGFXUciUgd4Rw8m9yyzG
4i9iwVYnsLb2dV5f+7aaRzbWUDE1XH/AT5WAAuikGLL71Aj/OLXGqqeV4eCk7sGW
2iIzQ3t9TRrnu/vjZKOG9Bf6oyYIuIG/tOgoJyFCNesZo4Pl90J/GlVKmVbAv6+l
90E66KQMFGriiEFkXfC0dM1WH6YwUDH2DwmgucZ5/nCSPNs0MJpmCj6SZWHsb7KM
FBSyTPoU5a4GIM8TUwAxHTQs+j2zxjoVEyZHAgvUBsF70mF0HZU8isPtGw4S2Fjc
hNROqhKNUhAPHtWYfaPw29bVOIm+ddjdt0BmU7hCQfOanms1CnM=
=ZH/N
-----END PGP SIGNATURE-----
Merge tag 's390-5.12-6' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Heiko Carstens:
- fix incorrect dereference of the ext_params2 external interrupt
parameter, which leads to an instant kernel crash if a pfault
interrupt occurs.
- add forgotten stack unwinder support, and fix memory leak for the
new machine check handler stack.
- fix inline assembly register clobbering due to KASAN code
instrumentation.
* tag 's390-5.12-6' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/setup: use memblock_free_late() to free old stack
s390/irq: fix reading of ext_params2 field from lowcore
s390/unwind: add machine check handler stack
s390/cpcmd: fix inline assembly register clobbering
In ice_suspend(), ice_clear_interrupt_scheme() is called, and then
irq_free_descs() will be eventually called to free irq and its descriptor.
In ice_resume(), ice_init_interrupt_scheme() is called to allocate new
irqs. However, in ice_rebuild_arfs(), struct irq_glue and struct cpu_rmap
maybe cannot be freed, if the irqs that released in ice_suspend() were
reassigned to other devices, which makes irq descriptor's affinity_notify
lost.
So call ice_free_cpu_rx_rmap() before ice_clear_interrupt_scheme(), which
can make sure all irq_glue and cpu_rmap can be correctly released before
corresponding irq and descriptor are released.
Fix the following memory leak.
unreferenced object 0xffff95bd951afc00 (size 512):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
18 00 00 00 18 00 18 00 70 fc 1a 95 bd 95 ff ff ........p.......
00 00 ff ff 01 00 ff ff 02 00 ff ff 03 00 ff ff ................
backtrace:
[<0000000072e4b914>] __kmalloc+0x336/0x540
[<0000000054642a87>] alloc_cpu_rmap+0x3b/0xb0
[<00000000f220deec>] ice_set_cpu_rx_rmap+0x6a/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
unreferenced object 0xffff95bd81b0a2a0 (size 96):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
38 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 8...............
b0 a2 b0 81 bd 95 ff ff b0 a2 b0 81 bd 95 ff ff ................
backtrace:
[<00000000582dd5c5>] kmem_cache_alloc_trace+0x31f/0x4c0
[<000000002659850d>] irq_cpu_rmap_add+0x25/0xe0
[<00000000495a3055>] ice_set_cpu_rx_rmap+0xb4/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove vsi->netdev->name from the trace.
This is redundant information. With the devinfo trace, the adapter
is already identifiable.
Previously following error was produced when compiling against sparse.
i40e_main.c:2571 i40e_sync_vsi_filters() error:
we previously assumed 'vsi->netdev' could be null (see line 2323)
Fixes: b603f9dc20 ("i40e: Log info when PF is entering and leaving Allmulti mode.")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Init pointer with NULL in default switch case statement.
Previously the error was produced when compiling against sparse.
i40e_debugfs.c:582 i40e_dbg_dump_desc() error: uninitialized symbol 'ring'.
Fixes: 44ea803e2f ("i40e: introduce new dump desc XDP command")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove error handling through pointers. Instead use plain int
to return value from i40e_run_xdp(...).
Previously:
- sparse errors were produced during compilation:
i40e_txrx.c:2338 i40e_run_xdp() error: (-2147483647) too low for ERR_PTR
i40e_txrx.c:2558 i40e_clean_rx_irq() error: 'skb' dereferencing possible ERR_PTR()
- sk_buff* was used to return value, but it has never had valid
pointer to sk_buff. Returned value was always int handled as
a pointer.
Fixes: 0c8493d90b ("i40e: add XDP support for pass and drop actions")
Fixes: 2e68931238 ("i40e: split XDP_TX tail and XDP_REDIRECT map flushing")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Change parameters order in aq_get_phy_register() due to wrong
statistics in PHY reported by ethtool. Previously all PHY statistics were
exactly the same for all interfaces
Now statistics are reported correctly - different for different interfaces
Fixes: 0514db37dd ("i40e: Extend PHY access with page change flag")
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This batch became unexpectedly bigger due to the pending ASoC
patches, but all look small and fine device-specific fixes.
Many of the commits are for ASoC Intel drivers, while the rest
are for ASoC small codec/platform fixes and HD-audio quirks.
-----BEGIN PGP SIGNATURE-----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=NnhZ
-----END PGP SIGNATURE-----
Merge tag 'sound-5.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This batch became unexpectedly bigger due to the pending ASoC patches,
but all look small and fine device-specific fixes.
Many of the commits are for ASoC Intel drivers, while the rest are for
ASoC small codec/platform fixes and HD-audio quirks"
* tag 'sound-5.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (21 commits)
ALSA: hda/realtek: Fix speaker amp setup on Acer Aspire E1
ALSA: aloop: Fix initialization of controls
ALSA: hda/conexant: Apply quirk for another HP ZBook G5 model
ASoC: fsl_esai: Fix TDM slot setup for I2S mode
ASoC: codecs: lpass-rx-macro: set npl clock rate correctly
ASoC: codecs: lpass-tx-macro: set npl clock rate correctly
ASoC: sunxi: sun4i-codec: fill ASoC card owner
ASoC: cygnus: fix for_each_child.cocci warnings
ASoC: max98373: Added 30ms turn on/off time delay
ASoC: max98373: Changed amp shutdown register as volatile
ASoC: intel: atom: Remove 44100 sample-rate from the media and deep-buffer DAI descriptions
ASoC: intel: atom: Stop advertising non working S24LE support
ASoC: wm8960: Fix wrong bclk and lrclk with pll enabled for some chips
ASoC: SOF: Intel: move ELH chip info
ASoC: SOF: Intel: APL: set shutdown callback to hda_dsp_shutdown
ASoC: SOF: Intel: CNL: set shutdown callback to hda_dsp_shutdown
ASoC: SOF: Intel: ICL: set shutdown callback to hda_dsp_shutdown
ASoC: SOF: Intel: TGL: set shutdown callback to hda_dsp_shutdown
ASoC: SOF: Intel: TGL: fix EHL ops
ASoC: SOF: core: harden shutdown helper
...
stable versions.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmBu7g0UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroOb6wf/aKgdBEGlWA1qVci/Z19uAlgr30vN
IXsDGG7XJWtcjCK18T23o1WOmGhyMzSAic3HjmyZtVKJ/OMXDLOE7yrcOgDMtx7l
M5kPUiPjbbMFQB2oG/hzafq4FDfqyL8oOJf2+SvElkUNx43nrJ/FuaXKoq3ae5y8
sQ+JGKnM/FYnP0++buItQ+QN1mcUXq7RmfYguUhjSUzkx1KjVZJuPpdV6VB8pTpD
FBtOvBomlCSov1wNpsFMFp31VRsu5wGVU0/9CaKpKAvM7ZlEVnLygzIWZHyE6vfl
VX4snrd1onlgRacthkovLYaArisGLgWPQjHjRa6YE0qm6rUoZM9VWQoprg==
=Szst
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fix from Paolo Bonzini:
"A lone x86 patch, for a bug found while developing a backport to
stable versions"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86/mmu: preserve pending TLB flush across calls to kvm_tdp_mmu_zap_sp
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCYG7FBgAKCRCRxhvAZXjc
osGSAQCW7V8zPhZ7Zwll3QeUk0xAqD6e6T3Uv3EoQPKCVcc00gEA/hQtDJYSGZWI
22hPAffU2YOKeYDXq7SIu+eJ1y/ShQ0=
=xfme
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2021-04-08' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull close_range() fix from Christian Brauner:
"Syzbot reported a bug in close_range.
Debugging this showed we didn't recalculate the current maximum fd
number for CLOSE_RANGE_UNSHARE | CLOSE_RANGE_CLOEXEC after we unshared
the file descriptors table. As a result, max_fd could exceed the
current fdtable maximum causing us to set excessive bits.
As a concrete example, let's say the user requested everything from fd
4 to ~0UL to be closed and their current fdtable size is 256 with
their highest open fd being 4. With CLOSE_RANGE_UNSHARE the caller
will end up with a new fdtable which has room for 64 file descriptors
since that is the lowest fdtable size we accept. But now max_fd will
still point to 255 and needs to be adjusted. Fix this by retrieving
the correct maximum fd value in __range_cloexec().
I've carried this fix for a little while but since there was no
linux-next release over easter I waited until now.
With this change close_range() can be further simplified but imho we
are in no hurry to do that and so I'll defer this for the 5.13 merge
window"
* tag 'for-linus-2021-04-08' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
file: fix close_range() for unshare+cloexec
Pull umount fix from Al Viro:
"Brown paperbag time: dumb braino in the series that went into 5.7
broke the 'don't step into ->d_weak_revalidate() when umount(2) looks
the victim up' behaviour.
Spotted only now - saw
if (!err && unlikely(nd->flags & LOOKUP_MOUNTPOINT)) {
err = handle_lookup_down(nd);
nd->flags &= ~LOOKUP_JUMPED; // no d_weak_revalidate(), please...
}
and went "why do we clear that flag here - nothing below that point is
going to check it anyway" / "wait a minute, what is it doing *after*
complete_walk() (which is where we check that flag and call
->d_weak_revalidate())" / "how could that possibly _not_ break?",
followed by reproducing the breakage and verifying that the obvious
fix of that braino does, indeed, fix it.
The reproducer is (assuming that $DIR exists and is exported r/w to
localhost)
mkdir $DIR/a
mkdir /tmp/foo
mount --bind /tmp/foo /tmp/foo
mkdir /tmp/foo/a
mkdir /tmp/foo/b
mount -t nfs4 localhost:$DIR/a /tmp/foo/a
mount -t nfs4 localhost:$DIR /tmp/foo/b
rmdir /tmp/foo/b/a
umount /tmp/foo/b
umount /tmp/foo/a
umount -l /tmp/foo # will get everything under /tmp/foo, no matter what
Correct behaviour is successful umount; broken kernels (5.7-rc1 and
later) get
umount.nfs4: /tmp/foo/a: Stale file handle
Note that bind mount is there to be able to recover - on broken
kernels we'd get stuck with impossible-to-umount filesystem if not for
that.
FWIW, that braino had been posted for review back then, at least
twice. Unfortunately, the call of complete_walk() was outside of diff
context, so the bogosity hadn't been immediately obvious from the
patch alone ;-/"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
LOOKUP_MOUNTPOINT: we are cleaning "jumped" flag too late
If the beacon head attribute (NL80211_ATTR_BEACON_HEAD)
is too short to even contain the frame control field,
we access uninitialized data beyond the buffer. Fix this
by checking the minimal required size first. We used to
do this until S1G support was added, where the fixed
data portion has a different size.
Reported-and-tested-by: syzbot+72b99dcf4607e8c770f3@syzkaller.appspotmail.com
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: 1d47f1198d ("nl80211: correctly validate S1G beacon head")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20210408154518.d9b06d39b4ee.Iff908997b2a4067e8d456b3cb96cab9771d252b8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The branch displacement logic in the BPF JIT compilers for x86 assumes
that, for any generated branch instruction, the distance cannot
increase between optimization passes.
But this assumption can be violated due to how the distances are
computed. Specifically, whenever a backward branch is processed in
do_jit(), the distance is computed by subtracting the positions in the
machine code from different optimization passes. This is because part
of addrs[] is already updated for the current optimization pass, before
the branch instruction is visited.
And so the optimizer can expand blocks of machine code in some cases.
This can confuse the optimizer logic, where it assumes that a fixed
point has been reached for all machine code blocks once the total
program size stops changing. And then the JIT compiler can output
abnormal machine code containing incorrect branch displacements.
To mitigate this issue, we assert that a fixed point is reached while
populating the output image. This rejects any problematic programs.
The issue affects both x86-32 and x86-64. We mitigate separately to
ease backporting.
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The branch displacement logic in the BPF JIT compilers for x86 assumes
that, for any generated branch instruction, the distance cannot
increase between optimization passes.
But this assumption can be violated due to how the distances are
computed. Specifically, whenever a backward branch is processed in
do_jit(), the distance is computed by subtracting the positions in the
machine code from different optimization passes. This is because part
of addrs[] is already updated for the current optimization pass, before
the branch instruction is visited.
And so the optimizer can expand blocks of machine code in some cases.
This can confuse the optimizer logic, where it assumes that a fixed
point has been reached for all machine code blocks once the total
program size stops changing. And then the JIT compiler can output
abnormal machine code containing incorrect branch displacements.
To mitigate this issue, we assert that a fixed point is reached while
populating the output image. This rejects any problematic programs.
The issue affects both x86-32 and x86-64. We mitigate separately to
ease backporting.
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Experimentally have found PV on hvs4 reports fifo full
error with expected settings and does not with one less
This appears as:
[drm:drm_atomic_helper_wait_for_flip_done] *ERROR* [CRTC:82:crtc-3] flip_done timed out
with bit 10 of PV_STAT set "HVS driving pixels when the PV FIFO is full"
Fixes: c8b75bca92 ("drm/vc4: Add KMS support for Raspberry Pi.")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210318161328.1471556-3-maxime@cerno.tech
The vc4_plane_atomic_async_update function assigns twice in a row the
src_h field in the drm_plane_state structure to the same value. Remove
the second one.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210318161328.1471556-2-maxime@cerno.tech
Right now, if a call to kvm_tdp_mmu_zap_sp returns false, the caller
will skip the TLB flush, which is wrong. There are two ways to fix
it:
- since kvm_tdp_mmu_zap_sp will not yield and therefore will not flush
the TLB itself, we could change the call to kvm_tdp_mmu_zap_sp to
use "flush |= ..."
- or we can chain the flush argument through kvm_tdp_mmu_zap_sp down
to __kvm_tdp_mmu_zap_gfn_range. Note that kvm_tdp_mmu_zap_sp will
neither yield nor flush, so flush would never go from true to
false.
This patch does the former to simplify application to stable kernels,
and to make it further clearer that kvm_tdp_mmu_zap_sp will not flush.
Cc: seanjc@google.com
Fixes: 048f49809c ("KVM: x86/mmu: Ensure TLBs are flushed for TDP MMU during NX zapping")
Cc: <stable@vger.kernel.org> # 5.10.x: 048f49809c: KVM: x86/mmu: Ensure TLBs are flushed for TDP MMU during NX zapping
Cc: <stable@vger.kernel.org> # 5.10.x: 33a3164161: KVM: x86/mmu: Don't allow TDP MMU to yield when recovering NX pages
Cc: <stable@vger.kernel.org>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This includes two fixes:
- Fix memory leak in tb_retimer_add()
- Off by one in tb_port_find_retimer()
Both have been in linux-next without reported issues.
-----BEGIN PGP SIGNATURE-----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=lvg3
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus
Mika writes:
thunderbolt: Fixes for v5.12-rc7
This includes two fixes:
- Fix memory leak in tb_retimer_add()
- Off by one in tb_port_find_retimer()
Both have been in linux-next without reported issues.
* tag 'thunderbolt-for-v5.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Fix off by one in tb_port_find_retimer()
thunderbolt: Fix a leak in tb_retimer_add()
cfg80211_inform_bss expects to receive a TSF value, but is given the
time since boot in nanoseconds. TSF values are expected to be at
microsecond scale rather than nanosecond scale.
Signed-off-by: A. Cody Schuffelen <schuffelen@google.com>
Link: https://lore.kernel.org/r/20210318200419.1421034-1-schuffelen@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A WARN_ON(wdev->conn) would trigger in cfg80211_sme_connect(), if multiple
send_msg(NL80211_CMD_CONNECT) system calls are made from the userland, which
should be anticipated and handled by the wireless driver. Remove this WARN_ON()
to prevent kernel panic if kernel is configured to "panic_on_warn".
Bug reported by syzbot.
Reported-by: syzbot+5f9392825de654244975@syzkaller.appspotmail.com
Signed-off-by: Du Cheng <ducheng2@gmail.com>
Link: https://lore.kernel.org/r/20210407162756.6101-1-ducheng2@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The incorrect timeout check caused probing to happen when it did
not need to happen. This in turn caused tx performance drop
for around 5 seconds in ath10k-ct driver. Possibly that tx drop
is due to a secondary issue, but fixing the probe to not happen
when traffic is running fixes the symptom.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Fixes: 9abf4e4983 ("mac80211: optimize station connection monitor")
Acked-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210330230749.14097-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Normally, TXQs have
txq->tid = tid;
txq->ac = ieee80211_ac_from_tid(tid);
However, the special management TXQ actually has
txq->tid = IEEE80211_NUM_TIDS; // 16
txq->ac = IEEE80211_AC_VO;
This makes sense, but ieee80211_ac_from_tid(16) is the same
as ieee80211_ac_from_tid(0) which is just IEEE80211_AC_BE.
Now, normally this is fine. However, if the netdev queues
were stopped, then the code in ieee80211_tx_dequeue() will
propagate the stop from the interface (vif->txqs_stopped[])
if the AC 2 (ieee80211_ac_from_tid(txq->tid)) is marked as
stopped. On wake, however, __ieee80211_wake_txqs() will wake
the TXQ if AC 0 (txq->ac) is woken up.
If a driver stops all queues with ieee80211_stop_tx_queues()
and then wakes them again with ieee80211_wake_tx_queues(),
the ieee80211_wake_txqs() tasklet will run to resync queue
and TXQ state. If all queues were woken, then what'll happen
is that _ieee80211_wake_txqs() will run in order of HW queues
0-3, typically (and certainly for iwlwifi) corresponding to
ACs 0-3, so it'll call __ieee80211_wake_txqs() for each AC in
order 0-3.
When __ieee80211_wake_txqs() is called for AC 0 (VO) that'll
wake up the management TXQ (remember its tid is 16), and the
driver's wake_tx_queue() will be called. That tries to get a
frame, which will immediately *stop* the TXQ again, because
now we check against AC 2, and AC 2 hasn't yet been marked as
woken up again in sdata->vif.txqs_stopped[] since we're only
in the __ieee80211_wake_txqs() call for AC 0.
Thus, the management TXQ will never be started again.
Fix this by checking txq->ac directly instead of calculating
the AC as ieee80211_ac_from_tid(txq->tid).
Fixes: adf8ed01e4 ("mac80211: add an optional TXQ for other PS-buffered frames")
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210323210500.bf4d50afea4a.I136ffde910486301f8818f5442e3c9bf8670a9c4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Recompiling with the new extended version of struct rfkill_event
broke systemd in *two* ways:
- It used "sizeof(struct rfkill_event)" to read the event, but
then complained if it actually got something != 8, this broke
it on new kernels (that include the updated API);
- It used sizeof(struct rfkill_event) to write a command, but
didn't implement the intended expansion protocol where the
kernel returns only how many bytes it accepted, and errored
out due to the unexpected smaller size on kernels that didn't
include the updated API.
Even though systemd has now been fixed, that fix may not be always
deployed, and other applications could potentially have similar
issues.
As such, in the interest of avoiding regressions, revert the
default API "struct rfkill_event" back to the original size.
Instead, add a new "struct rfkill_event_ext" that extends it by
the new field, and even more clearly document that applications
should be prepared for extensions in two ways:
* write might only accept fewer bytes on older kernels, and
will return how many to let userspace know which data may
have been ignored;
* read might return anything between 8 (the original size) and
whatever size the application sized its buffer at, indicating
how much event data was supported by the kernel.
Perhaps that will help avoid such issues in the future and we
won't have to come up with another version of the struct if we
ever need to extend it again.
Applications that want to take advantage of the new field will
have to be modified to use struct rfkill_event_ext instead now,
which comes with the danger of them having already been updated
to use it from 'struct rfkill_event', but I found no evidence
of that, and it's still relatively new.
Cc: stable@vger.kernel.org # 5.11
Reported-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com> # LLVM/Clang v12.0.0-r4 (x86-64)
Link: https://lore.kernel.org/r/20210319232510.f1a139cfdd9c.Ic5c7c9d1d28972059e132ea653a21a427c326678@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some race conditions, with more clients and traffic configuration,
below crash is seen when making the interface down. sta->fast_rx wasn't
cleared when STA gets removed from 4-addr AP_VLAN interface. The crash is
due to try accessing 4-addr AP_VLAN interface's net_device (fast_rx->dev)
which has been deleted already.
Resolve this by clearing sta->fast_rx pointer when STA removes
from a 4-addr VLAN.
[ 239.449529] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 239.449531] pgd = 80204000
...
[ 239.481496] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.4.60 #227
[ 239.481591] Hardware name: Generic DT based system
[ 239.487665] task: be05b700 ti: be08e000 task.ti: be08e000
[ 239.492360] PC is at get_rps_cpu+0x2d4/0x31c
[ 239.497823] LR is at 0xbe08fc54
...
[ 239.778574] [<80739740>] (get_rps_cpu) from [<8073cb10>] (netif_receive_skb_internal+0x8c/0xac)
[ 239.786722] [<8073cb10>] (netif_receive_skb_internal) from [<8073d578>] (napi_gro_receive+0x48/0xc4)
[ 239.795267] [<8073d578>] (napi_gro_receive) from [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames+0xbcc/0x12d4 [mac80211])
[ 239.804776] [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames [mac80211]) from [<c7b84d4c>] (ieee80211_rx_napi+0x7b8/0x8c8 [mac8
0211])
[ 239.815857] [<c7b84d4c>] (ieee80211_rx_napi [mac80211]) from [<c7f63d7c>] (ath11k_dp_process_rx+0x7bc/0x8c8 [ath11k])
[ 239.827757] [<c7f63d7c>] (ath11k_dp_process_rx [ath11k]) from [<c7f5b6c4>] (ath11k_dp_service_srng+0x2c0/0x2e0 [ath11k])
[ 239.838484] [<c7f5b6c4>] (ath11k_dp_service_srng [ath11k]) from [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll+0x20/0x84 [ath11k_ahb]
)
[ 239.849419] [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll [ath11k_ahb]) from [<8073ce1c>] (net_rx_action+0xe0/0x28c)
[ 239.860945] [<8073ce1c>] (net_rx_action) from [<80324868>] (__do_softirq+0xe4/0x228)
[ 239.871269] [<80324868>] (__do_softirq) from [<80324c48>] (irq_exit+0x98/0x108)
[ 239.879080] [<80324c48>] (irq_exit) from [<8035c59c>] (__handle_domain_irq+0x90/0xb4)
[ 239.886114] [<8035c59c>] (__handle_domain_irq) from [<8030137c>] (gic_handle_irq+0x50/0x94)
[ 239.894100] [<8030137c>] (gic_handle_irq) from [<803024c0>] (__irq_svc+0x40/0x74)
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Link: https://lore.kernel.org/r/1616163532-3881-1-git-send-email-seevalam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We've got a report about Acer Aspire E1 (PCI SSID 1025:0840) that
loses the speaker output after resume. With the comparison of COEF
dumps, it was identified that the COEF 0x0d bits 0x6000 corresponds to
the speaker amp.
This patch adds the specific quirk for the device to restore the COEF
bits at the codec (re-)initialization.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1183869
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210407095730.12560-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We need to enable MC CAC for mclk switching to work.
Fixes: d765129a71 ("drm/amd/pm: correct sclk/mclk dpm enablement")
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1561
Tested-by: Konstantin Kharlamov <Hi-Angel@yandex.ru>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
ttm->num_pages is uint32. Hit overflow when << PAGE_SHIFT directly
Fixes: 230c079fdc ("drm/ttm: make num_pages uint32_t")
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
ttm->num_pages is uint32. Hit overflow when << PAGE_SHIFT directly
Fixes: 230c079fdc ("drm/ttm: make num_pages uint32_t")
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
