This patch is adding a sysfs entry in order to be able to get
access to SST FW version.
Signed-off-by: Sebastien Guiriec <sebastien.guiriec@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using regmap_update_bits(..., mask, 1) with 'mask' following (1 << k)
and k greater than 0 is wrong. Indeed, _regmap_update_bits will perform
(mask & 1), which results in 0 if LSB of mask is 0. Thus the call
regmap_update_bits(..., mask, 1) is in reality equivalent to
regmap_update_bits(..., mask, 0).
In such a case, the correct use is regmap_update_bits(..., mask, mask).
This driver is performing such a mistake with the CS42L56_AIN*_REF_MASK
masks, which equal 0x10, 0x20, 0x40 and 0x80. Fix the driver to make it
consistent with the API. Please note that this change is untested,
as I do not have this piece of hardware. Testers are welcome!
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch will check the type of embedded controls for a widget, and
only free the TLV of volume mixers. Bytes controls don't have TLV.
Just free the private value which is used as struct soc_mixer_control
for volume mixers or soc_bytes_ext for bytes controls. No need to cast
to these types before freeing it.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch can create multiple enumerated mixer controls for a widget.
Previously topology kernel driver assumes a widget can have only one
emumerated mixer control. We need to remove this restriction for Broxton.
Its firmware modules (widgets) may need multiple enum controls based on
the channel and MIC combination.
No ABI change is needed. The ABI allows a widget to embed multiple
controls.
Reported-by: G Kranthi <gudishax.kranthikumar@intel.com>
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple_card_utils was created as simple_card_core in 1st prototype,
and current code still have it. Let's tidyup
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSIU was controlled by SSI before, but
commit c7f69ab53("ASoC: rsnd: use mod base common method on SSIU")
separated it into ssiu.c
But, it didn't care about rsnd_get_dalign() for judging SSI_BUSIF_DALIGN
register value which changes the stream data order.
This function will be called from cmd/src/ssiu now, but current code
still cares ssi, not ssiu.
This patch fix it up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYRIGyAAoJEHm+PkMAQRiG2ksH/jwMUT9j6glbwESxbn1YTqTM
QcBT5AMc7D0wNuidQe0hWZMtG4RbC+4ZhxzZl2wPgA2gueJ+rBnyX7bgtA7ka8ka
Fdc3u/Q1v38HPzf8iBnxcdCs40VgsoMLjFYCXrpOxuGDNKYzRd+Q8aI2TeGvzbyi
X8+6oAWifBwo2oA06jfcuUncEWbyDDyK9aQksmfKOpjHdb26yELPEhsPOlds1g7E
jYLnvUVnU2CoFaumta+rZQ0kzLdc4Ntu0wEao6WzJuQKsgoID+tS/6iudi8cUhDp
YowGAVoOfr6rAJB0mwrDVfugpamaT3386XKyocdNsK0/jR60UIJ8x+WzvvSU+lY=
=JTBj
-----END PGP SIGNATURE-----
Backmerge tag 'v4.9-rc8' into drm-next
Linux 4.9-rc8
Daniel requested this so we could apply some follow on fixes cleanly to -next.
This patch adds the sound machine driver for the TM2 and TM2E boards.
Speaker and headphone playback, Main Mic capture, Bluetooth, Voice
call and external accessory are supported.
Signed-off-by: Inha Song <ideal.song@samsung.com>
[k.kozlowski: rebased on 4.1]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
[s.nawrocki: rebased to 4.7, adjustment to the ASoC core changes,
removed unused ops and direct calls to the max98504 function,
added parsing of "audio-amplifier" and "audio-codec"
properties, added TDM API calls, switched to gpiod API]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In current ALSA SoC, Codec only has suspend/resume feature,
but it should be supported on Component level. This patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now, Card has component_dev_list, we can replace aux_comp_list
to component_dev_list with new auxiliary flags
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Card has Codec list (= codec_dev_list), but Codec will be
removed in the future. Because of this reason, this patch adds
new Component list in Card, and replace Codec list.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec on the H3 is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the H3 has no HP (headphone) and HBIAS support, and no
MIC3 input. The FIFO related registers are slightly rearranged.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec in the A23 is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the A23 does not have LINEOUT, and it does not support
headset jack detection or buttons.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of hard-coded "i2c-10EC5670:00", use the translation helper to
avoid the mismatch between i2c-codec and ACPI strings just like what
we've done for bytcr_rt5640. This gives more robust binding on funky
devices like Dell Wyse 3040.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is an issue about pop noise in NAU88L25 as follows.
Issue 54078: Chell_headphone pop back from S3
(1)Play directly to hw, bypassing CRAS:
sox -b 16 -n -t alsa hw:0,0 synth sine 200 sine 200
(2)Close lid or powerd_dbus_suspend, then press a key to resume.
(3)no audio after resume
(4)Audio will be back after close then reopen the pcm device.
After verification, we find one defect is that semaphone lock is not
long enough and expired. In this situation, the playback comes back
early but pauses a while to wait for the crosstalk detection done.
But the detection spends too much time and lock time is up. Therefore,
the playback and jack detection sequence interfere to each other.
That breaks sequence and makes noise. The driver extends the lock
time for the issue.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The usage pattern of kthread worker in Intel SST drivers can be
replaced gracefully with the normal workqueue, which is more light-
weight and easier to manage in general. Let's do it.
While in the replacement, move the schedule_work() call inside the
spinlock for excluding the race, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to modify the state of some of our own pins and are currently
not taking account that the pin name may have a name_prefix applied
to it.
Replace the snd_soc_dapm_x_pin functions with the equivalent
snd_soc_component_x_pin functions so that any name_prefix will be
handled automatically.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's often the case that a codec driver will need to control its
own pins. However, if a name_prefix has been applied to this codec it
must be included in the name passed to any of the snd_soc_dapm_x_pin()
functions.
The behaviour of the existing pin control functions is reasonable, since
you may want to search for a fully-specified name within the scope of an
entire card. This means that we can't apply the prefix in these functions
because it will break card-scope searches.
Constructing a prefixed string "manually" in codec drivers leads to a lot
of repetition of the same code.
To make this tidier in codec drivers this patch adds a new set of
equivalent functions that take a struct snd_soc_component instead of a
dapm context and automatically add the component's name_prefix to the
given name. This makes it a simple change in codec drivers to be
prefix-safe.
The new functions are not quite trivial enough to be inlines and the
compiler won't be able to compile-away any part of them.
Although it looks somewhat inefficient to have to allocate a temporary
buffer and combine strings, the current design of the widget list
doesn't lend itself to a more optimized implementation - it's a single
list of all widgets on a card and is searched linearly for a matching
string. As pin state changes are generally low-frequency events it's
unlikely to be a significant issue - at least not enough to rewrite the
widget list handling just for this.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5670 driver supports also RT5672 codec, but its ACPI ID is missing.
This was found on Dell Wyse 3040 box.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Dell Wyse 3040 requires the platform workaround for enabling dmic and
jack detection as defined for Braswell CRB.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing ACPI ID 10EC5672 for Cherry Trail, which bounds with
cht-bsw-rt5672 driver. This combination was found on Dell Wyse 3040.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drm/qxl: various bugfixes and cleanups,
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJYMzLfAAoJEEy22O7T6HE41rIQANAEl/o8cYUoyYTJlhmmnl2U
K+QBdr7PACdbr8RZrGpwA5ad9ZJGijpZRd2gThrzNS0JBdZI48gPEzU7V206xlyD
AriBeAu6IkoBTEl+GGx2DfvOdLR6+7KlIrDYIpl2vILgkqlHhneXdHR3R03byRHG
2Jrxv2YQxCs8swtAb8FRkVNaUgrfkKOKFFlx1LoLFApYeP02oSxZp0Ve4nuRNj7x
9DCivIw4NyQ9tY1fORapmrEPTerqZnzYdb9RFSv4xilx4Stq1UWdXfTSpwXZHZaG
VroXZb1I0fZEk1aapIxuzLZFGNSM7wLET/nK02sSvzxJJv2PiyVAabIo70nUqsQK
H/iGT2g4MZC1Yvz6evENtckbiA1p3F9jnd+Po9ivDY/RrTpND3hVC2WbcOXWxZkb
m69muvXfrnZwoF9xWPG8aTrCATim++1Ty8/8LoKdVq1d0Dp/Gzk8KnklBPY2vRFt
dpxqH3jLgED/QcO5W/yQdf0kPRsrNwKFNLqP9bCF2hMIw1VHHddZtnBBXDGATXYq
hdFA8EEg3gh/kY7V8b+GyxjRKRbveG208hu+H4EirxHmRn5xJN1VoTLk9va+AJL1
I30l4USLDkTgf1AjYmk7yFIUTemCtwjfa0lsuu4l3rRJ3k1eBrtZe2cpWv2BoQDU
by0sNnDelzJTQ9/v1i3J
=OYiT
-----END PGP SIGNATURE-----
Merge tag 'drm-qemu-20161121' of git://git.kraxel.org/linux into drm-next
drm/virtio: fix busid in a different way, allocate more vbufs.
drm/qxl: various bugfixes and cleanups,
* tag 'drm-qemu-20161121' of git://git.kraxel.org/linux: (224 commits)
drm/virtio: allocate some extra bufs
qxl: Allow resolution which are not multiple of 8
qxl: Don't notify userspace when monitors config is unchanged
qxl: Remove qxl_bo_init() return value
qxl: Call qxl_gem_{init, fini}
qxl: Add missing '\n' to qxl_io_log() call
qxl: Remove unused prototype
qxl: Mark some internal functions as static
Revert "drm: virtio: reinstate drm_virtio_set_busid()"
drm/virtio: fix busid regression
drm: re-export drm_dev_set_unique
Linux 4.9-rc5
gp8psk: Fix DVB frontend attach
gp8psk: fix gp8psk_usb_in_op() logic
dvb-usb: move data_mutex to struct dvb_usb_device
iio: maxim_thermocouple: detect invalid storage size in read()
aoe: fix crash in page count manipulation
lightnvm: invalid offset calculation for lba_shift
Kbuild: enable -Wmaybe-uninitialized warnings by default
pcmcia: fix return value of soc_pcmcia_regulator_set
...
Disable IRQ when jack is NULL in rt298_mic_detect. So machine driver
can use it in suspend/resume.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel sst driver spews lots of kernel messages in INFO level;
typically, it gives a kernel message at each time it allocates or
frees a stream, or at each time when a stream is started or stopped.
This will piles up quickly, and it's almost useless for normal users,
so let's hide them to KERN_DEBUG level.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Functions are given external linkage by default making the extern's
unnecessary, as such remove them.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Functions are given external linkage by default making the extern's
unnecessary, as such remove them.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that I2S conflig blob structure is no longer in use, remove it.
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I2S blob config structure can change between DSP copier module versions.
We are not modifying these structures anyway and NHLT blobs specify them
properly, so use the blob directly to send the dma_control ipc instead
of using the predefined I2S blob config structure.
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Oddly enough, my version of GCC misses this uninitialized variable.
Fixes: ba2ff3027b ("ASoC: sunxi: Add support for A23/A33/H3 codec's analog path controls")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fields of structs with global storage are implicitly initialized to 0/NULL,
there is usually no need to do this explicitly.
Removing the initialization of the legacy suspend/resume callback fields
also gets the driver ready for the day when they are eventually removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Resources should be requested when the device is probed on the control bus
rather then when the CODEC is bound to the sound card. This allows things
like probe deferring and device managed allocations to work.
So move the GPIO request calls from the CODEC probe to the bus probe and
also make them managed along the way.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. The last user of these defines was removed in commit
f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support"). So
remove the defines as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We are not checking the return value from a call to wm_adsp_buffer_init
it looks like this used to be returned at the bottom of the function but
probably got missed when more error paths were added. This patch adds
the appropriate error check.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The internal codec on A23/A33/H3 is split into 2 parts. The
analog path controls are routed through an embedded custom register
bus accessed through the PRCM block.
The SoCs share a common set of inputs, outputs, and audio paths.
The following table lists the differences.
----------------------------------------
| Feature \ SoC | A23 | A33 | H3 |
----------------------------------------
| Headphone | v | v | |
----------------------------------------
| Line Out | | | v |
----------------------------------------
| Phone In/Out | v | v | |
----------------------------------------
Add an ASoC component driver for it. This should be tied to the codec
audio card as an auxiliary device. This patch adds the commont paths
and controls, and variant specific headphone out and line out.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
IOMMU needs DMA mapping function to use it. One solution is that
we can use DMA mapped dev on snd_pcm_lib_preallocate_pages_for_all()
for SNDRV_DMA_TYPE_DEV. But pcm_new and dma map timing are mismatched.
Thus, this patch uses SNDRV_DMA_TYPE_CONTINUOUS for pcm_new,
and use dma_sync_single_for_xxx() for each transfer.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas Sound driver requests DMA channel when .probe timing,
and release it when .remove timing. And use DMA on .start/.stop
But, Audio DMAC power ON was handled when request timing (= .probe),
and power OFF was when release timing (= .remove).
This means Audio DMAC power is always ON during driver was enabled.
The best choice to solve this issue is that DMAEngine side handle
this. But current DMAEngine API design can't solve atmic/non-atmic
context issue for power ON/OFF. So next better choice is sound
driver request/release DMA channel each time. This patch do it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The kcontrol pointer in wm_coeff_ctl is not used now.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We were adding firmware controls as card controls (using
snd_soc_add_codec_controls). The DSP is part of a specific codec so
we should be adding them as codec controls. Adding as codec controls
also means that if the codec has a name_prefix it will be added to
the control name, which won't happen when adding as a card control.
As that was the only use of the card pointer in struct wm_adsp it can
be removed.
For ADSP2 codecs a wm_adsp2_codec_probe() was added since the original
control handling was written, and that's the logical place to store a
pointer to the codec rather than delaying it until the codec is
powered-up.
For ADSP1 we don't use a codec_probe() stage so the codec pointer
initialization replaces the original card pointer initialization in
wm_adsp1_event().
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
cht_bsw_rt5645 driver allocates the own codec_id string but doesn't
release it. For simplicity, put the string in cht_mc_private; then
the string is allocated in a shot and released altogether.
Fixes: c8560b7c91 ("ASoC: cht_bsw_rt5645: Fix writing to string literal")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2S sound drivers for SmartQ board and WM8580 codec can be compile
tested to increase build coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of build time, Samsung ASoC drivers have rather runtime
dependency on Exynos or other Samsung platforms. For building they
require Common Clock Framework. If it is provided they could be compile
tested to increase build coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
MACH_SMDKC100, MACH_SMDKV210 and MACH_SMDKC110 are no longer supported
so we can drop the dead code. After this the driver no longer
differentiates between machines (S3C24xx machines are not supported by
it) so there is no need to override I2S device id in cpu_dai_name and
SEC_PLAYBACK dai_link can be removed as well.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
MACH_SMDKC100 was removed in commit b8529ec1c1 ("ARM: S5PC100: no more
support S5PC100 SoC"). MACH_SMDKV210 and MACH_SMDKC110 in commit
28c8331d38 ("ARM: S5PV210: Remove support for board files").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
dpcm_state_string() returns a pointer to a string literal. Modifying a
string literal causes undefined behaviour. So make the return type of the
function const char * to make it explicit that the returned value should
not be modified.
This patch is purely cosmetic, none of the users of dpcm_state_string()
attempt to modify the returned content.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8580 driver doesn't work without CONFIG_I2C anyway.
Let's remove #if IS_ENABLED(CONFIG_I2C), and use module_i2c_driver().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8523 driver doesn't work without CONFIG_I2C anyway.
Let's remove #if IS_ENABLED(CONFIG_I2C), and use module_i2c_driver().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The control list may contain shutdown controls for firmwares that are
not currently active, attempting to write this will at best fail. To
avoid this issue we skip any control that is not active.
Fixes: commit f4f0c4c60c ("ASoC: wm_adsp: Signal firmware shutdown
through event control")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm9081 driver doesn't work without CONFIG_I2C anyway.
Let's remove #if IS_ENABLED(CONFIG_I2C)
And, this patch adds "depends on I2C" to Kconfig
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
uda1380 driver doesn't work without CONFIG_I2C anyway.
Let's remove #if IS_ENABLED(CONFIG_I2C), and use module_i2c_driver().
And, this patch adds "depends on I2C" to Kconfig
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TSE-850 is an FM Transmitter Station Equipment, designed to generate
baseband signals for FM, mainly the DARC subcarrier, but other signals
are also possible.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
When this driver masters BCLK and/or LRCLK, and noone has stated
differently, assume that all the bits of a frame are used.
This relieves the cpu dai users from the duty to fill in the dividers for
the common case.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
const char * const [] is the preferred type for static string arrays since
this states explicitly that the individual entries are not going to be
changed. Due to limitations in the ASoC API it was not possible to use it
for enum text arrays. Commit 87023ff74b ("ASoC: Declare const properly
for enum texts") changed this, but most drivers still use 'const char
* []' as the type for their enum text arrays.
Change these occurrences of 'static * const char * []' to 'static const
char * const []'.
The conversion was done automatically using the following coccinelle
semantic patch:
// <smpl>
@disable optional_qualifier@
identifier s;
@@
static
-const char *
+const char * const
s[] = ...;
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 022d00ee0b ("ASoC: lpass-platform: Fix broken pcm data
usage") the stream specific information initialization was broken, with
the dma channel information not being initialized if there was no
alloc_dma_channel() helper function.
Before that, the DMA channel number was implicitly initialized to zero
because the backing store was allocated with devm_kzalloc(). When the
init code was rewritten, that implicit initialization was lost, and gcc
rightfully complains about an uninitialized variable being used.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lookup of the base register corresponding to a control is
duplicated in read and write so factor it out into a separate
function.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rtd->codec does not necessarily point to the CODEC instance for which the
callback was called (e.g. for CODEC<->CODEC or multi-CODEC links). Use
dai->codec instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
const char * const [] is the preferred type for static string arrays since
this states explicitly that the individual entries are not going to be
changed. Due to limitations in the ASoC API it was not possible to use it
for enum text arrays. Commit 87023ff74 ('ASoC: Declare const properly for
enum texts') changed this, but most drivers still use 'const char
* []' as the type for their enum text arrays.
Change these occurrences of 'static * const char * []' to 'static const
char * const []'.
The conversion was done automatically using the following coccinelle semantic
patch:
// <smpl>
@disable optional_qualifier@
identifier s;
@@
static
-const char *
+const char * const
s[] = ...;
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a missing whitespace in the dev_err message between
"will" and "lead". Add the whitespace.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC Compress ops have only platform ops and no DAI ops unlike PCM device
where we have both platform ops as well as DAI ops.
So add compress dai ops and add this new structure to the ASoC core to make
compressed devices a first class ASoC citizen
Again like PCM ops, drivers are free to implement either or both of
these ops based on device needs.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most Baytrail-CR devices use analog differential microphones,
modify capture default to avoid DMI quirks. Keep digital mics
for all other configurations.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Baytrail-CR devices usually expose information in the DSDT
which can be used to auto-detect AIF1/AIF2 connections.
The CHAN package contains two integers, the first one describes
the AIF number (1: AIF1, 2: AIF2) and the second the MCLK
value (ignored in this patch)
For example the following information is found in Lenovo 100s:
Device (RTEK) {
[...]
Name (CHAN, Package (0x02)
{
One,
0x017D7840
})
While on Asus T100TAF the package values are:
Name (CHAN, Package (0x02)
{
0x02,
0x017D7840
})
This patch relies on the new common routine to extract
a package exposed by a device indexed with the HID value.
The CHAN package contents are queried from the machine driver
and stored in a structure.
If this auto-detection fails (missing or bad package in the
BIOS), the routing falls back to SSP0-AIF2.
Note that quirks may still be needed to support mono speakers
or microphone, but this should reduce the number of issues with
Baytrail significantly.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new common routine to extract a package exposed by a
device indexed with the HID value. The functionality is
implemented without assumptions on the package type or
structure to allow for reuse. The caller is responsible for
defining the name and allocating structures to store the
results, ACPICA will complain in case of type mismatches
or buffer size issues.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAC3101 is mostly identical to DAC3100 with the exception that it has
stereo speaker AMP instead of mono used in DAC3100.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch handles publishing acknowledged controls through ALSA.
These controls allow user-side to send events to the firmware and
wait for the firmware to acknowledge it.
Note that although acked controls only operate in the direction
host->firmware, and therefore they are write-only as seen from user-
side code, we have to make them readable to account for all the code
out there that assumes that ALSA controls are always readable (amixer
for example.)
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for firmware controls marked SYSTEM. These are
internal to the driver-firmware interface and do not have
a user-accessible ALSA control.
Signed-off-by: Stuart Henderson <stuarth@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch factors out converting a memory region type into
a name string, mainly so that it can be used in log commands.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the firmware has any system event signalling controls, signal
them during DSP PRE_PMD to tell the firmware it is about to be stopped.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SND_SOC_SMDK_WM8580_PCM Kconfig entry depends on either MACH_SMDKV210
or MACH_SMDKC110. Both of which were removed in commit 28c8331d38 ("ARM:
S5PV210: Remove support for board files") over two years ago. The driver
has been unselectable ever since.
Considering the lack of complaints about this it can be concluded that the
driver is unused and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a076d41823 ("ASoC: samsung: Drop AC97 drivers") removed some
unused code and the associated Kconfig options, but left those options
referenced in the Makefile. Remove the leftover references in the
Makefile.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver fine-tune some parameters to improve FLL performance.
Those items have description as follow.
(1)ICTRL_LATCH: FLL DSP speed capability control
When FLL running at high frequency with long decimal number, DSP needs
to operate at high speed. FLL DSP can optimize between performance and
power consumption by ICTRL_LATCH.(111 has highest power consumption.)
The default setting can be used to reduce power.
(2)CUTOFF500: loop filter cutoff frequency at 500Khz
It will give the best FLL performance but highest power consumption
to enable the cutoff frequency. FLL Loop Filter enable to reduce FLL
output noise, especially,(DCO frequency)/(FLL input reference frequency)
is not a integer.
(3)GAIN_ERR: FLL gain error correction threshold setting
The threshold is comparison between DCO and target frequency.
The value 1111 has the most sensitive threshold, that is, 1111 can have
the most accurate DCO to target frequency. However, the gain error setting
conditionally and inversely depends on FLL input reference clock rate.
Higher FLL reference input frequency can only set lower gain error, such
as 0000 for input reference from MCLK=12.288Mhz. On the other side, if FLL
reference input is from Frame Sync, 48KHz, higher error gain can apply
such as 1111.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Over Sampling Rate (OSR) is defined as CLK_ADC frequency divided by the
audio sample rate (Fs).
OSR = CLK_ADC / FS
The available OSRs are 32, 64, 128 or 256. Note that the OSR and Fs
values must be selected such that the maximum frequency of CLK_ADC
is less than 6.144 MHz. It is recommended to match the relationship
between OSR and clock SRC according to following Table.
ADC_RATE: 00(OSR=32) | CLK_ADC_SRC: 11(CODEC 1/8)
ADC_RATE: 01(OSR=64) | CLK_ADC_SRC: 10(CODEC1/4)
ADC_RATE: 10(OSR=128) | CLK_ADC_SRC: 01(CODEC 1/2)
ADC_RATE: 11(OSR=256) | CLK_ADC_SRC: 00(CODEC CLK)
The over sampling rate about DAC follows the same rule with ADCs.
The driver changes the OSR to 64 value when initiation for better FLL
performance and applies the dynamic SRC change by different OSR.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the short Frame Sync detection logic enabled, the logic will check the
short frame sync threshold. If frame sync is less than the setting;
for example, frame sync less than 252 MCLK, the short frame sync signal is
flagged, digital filter temporary mute and skip that data.
If the system was intended for sampling rate change which could create
temporary short frame sync and not enough MIPS to run the digital filter.
But the situation doesn't happen in ALSA architecure. Thus the Frame Sync
is always stable, then no require to do the detection. Therefore,
the dirver disables the function for better performance.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_get_dai_name() is used from snd_soc_of_get_dai_name(),
and it is assuming that DT is using "sound-dai" / "#sound-dai-cells".
But graph base DT is using "remote-endpoint". This patch makes
snd_soc_get_dai_name() non static for graph support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The compatible table was not updated when the support for DAC3100 was added.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The call to arizona_init_notifiers was only added for CODECs that are
generating voice trigger events, however, this is somewhat annoying
for machine drivers that might be used with multiple CODECs as they
need to conditionally register for the notifier, depending on the
CODEC being attached.
As the cost of initialising the notifier is so minimal, and we may
well add other events in the future that apply to more CODECs, simply
do this for all Arizona CODECs.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These functions are very thin wrappers around core functions, so they
make sense as inline functions. Also making them inline avoids build
issues in the case where the machine driver is built in but the CODEC
is built as a module.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core expects "const char * const" and "unsigned int" for enum
controls, the mixer control definitions in wm2200 use "const char *"
and "int". This patch corrects the type of these arrays.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/cs42l42.c:1972:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While going to suspend, if we have any pending D0i3 work scheduled,
flush that and force the DSP to goto D0i3 mode before going to suspend.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We were invoking pci_disable_device() while going to suspend-to-idle and
pci_enable_device() while coming back to active state.
Turns out that we do not need these calls as we only need system to be
wake capable when in suspend-to-idle state. The wake capability is
already done by enable_irq_wake() calls, so remove these unwanted calls
in driver.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check if the name strings are properly terminated, and only use valid
name strings to find existing physical DAI links to configure.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
pm8916_wcd_analog_enable_micbias_int1() should set micbias1_cap_mode
rather than micbias2_cap_mode.
Also change the order of pm8916_wcd_analog_enable_micbias_int1/init2
functions for better readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix build errors in sound/soc/fsl/fsl_spdif.c by selecting BITREVERSE.
Fixes these build errors:
sound/built-in.o: In function `spdif_write_channel_status':
fsl_spdif.c:(.text+0xbe39d): undefined reference to `byte_rev_table'
fsl_spdif.c:(.text+0xbe3a8): undefined reference to `byte_rev_table'
fsl_spdif.c:(.text+0xbe3be): undefined reference to `byte_rev_table'
fsl_spdif.c:(.text+0xbe3d8): undefined reference to `byte_rev_table'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The later Allwinner SoCs have a dedicated reset controller, and
peripherals have dedicated reset controls which need to be deasserted
before the associated peripheral can be used.
Add support for this to the quirks structure and probe/remove functions.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31's internal codec capture path has a mixer in front of the ADC
for each channel, capable of selecting various inputs, including
microphones, line in, phone in, and the main output mixer.
This patch adds the various controls, widgets and routes needed for
audio capture from the already supported inputs on the A31.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support was added to allow location of both CPU and CODEC components
of a DAI link from their parent's of_node if they did not have an
of_node themselves in this commit:
commit 3e0aa8d83b ("ASoC: core: If component doesn't have of_node
use parent's node instead")
However this leaves platforms as something of a special case as the
major DAI component that doesn't do this. Since this is useful for MFD
devices which often utilise a single device tree entry for the whole
device, add support for looking up platforms from the parent's of_node
as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using simple-card with the wm8978 doesn't work because simple card calls
set_sysclk on the clock index 0, which is not the MCLK in the WM8978.
Adjust the clock definition so that the clock 0 is the MCLK.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In our i2s driver, we were previously trying to guess which oversample the
user wanted to use by looking at the rate and trying to max it.
However, the cards, and especially simple-card with its mclk-fs property
will already provide the expected oversample ratio by using the set_sysclk
callback.
We can thus implement it and remove the logic to deal with the runtime
guess.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Cirrus Logic CS42L42 codec. SoundWire support
is not enabled. Features support for I2C control and I2S audio.
Signed-off-by: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A bugfix accidentally removed the implicit initialization of the
dma channel number, causing undefined behavior when
v->alloc_dma_channel is NULL:
sound/soc/qcom/lpass-platform.c: In function ‘lpass_platform_pcmops_open’:
sound/soc/qcom/lpass-platform.c:83:29: error: ‘dma_ch’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This adds back an explicit initialization to zero, restoring the
previous behavior for that case.
Fixes: 022d00ee0b ("ASoC: lpass-platform: Fix broken pcm data usage")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 SoC's codec has various inputs, outputs and microphone bias
supplies. These can be routed on the board in different ways, such as:
- HPCOM may be connected to have the headphone DC coupled.
- Microphones all use the MBIAS main microphone supply or one mic may
use the HBIAS supply, which supports headset detection and buttons.
- Line Out may be routed to an audio jack, or an onboard speaker amp
with power controls.
Add support for specifying the audio routes in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 internal codec has 3 microphone outputs, of which MIC2 and MIC3
are muxed internally. The resulting two microphone inputs have separate
gain controls and mixer inputs.
The codec also has 2 microphone bias pins. HBIAS is specifically for the
headphone jack, which also supports headphone detection and control
buttons. These extra functions are not supported yet. The other, MBIAS,
is for all other analog microphones.
There is also mention of digital microphone support, but documentation
is scarce, and no hardware with it is available.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 integrated codec has a second "Line Out" output which does not
include an integrated amplifier in its path. This path does have a
separate volume control.
This patch adds support for the playback path from the DAC to the Line
Out pins.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the regmap conversion ac97_read/ac97_write are just simple wrappers
around snd_soc_read/snd_soc_write. Use those instead directly and remove
the wrappers.
Also use snd_soc_update_bits() where appropriate.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the stac9766 driver still uses custom snd_soc_codec_driver IO
callbacks. This has been deprecated for a while, so convert the stac9766
driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The stac9766 driver has a header file that defines 3 register locations.
Move these to the main source file since it is not really worth it having a
separate file for them. The header file is now empty and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AC'97 standard defines paging support for the register range 0x60-0x6f.
Meaning registers in this window are mapped to different physical registers
depending on the setting of the page select register (0x24).
The stac9766 implements support for switching between page 0 and page 1
depending on the addressed register. But the driver never accesses any
registers from page 1, in addition page 0 is the page selected by default.
Considering the development history it is unlikely that the driver will see
any new features that require paging support. Removing the paging support
makes transitioning the driver to regmap a bit more straight forward.
The default register value table is update to contain the values from page
0, rather than page 1.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used instead and the defines are
unused.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new flag bit SND_SOC_TPLG_LNK_FLGBIT_VOICE_WAKEUP to link flags.
If a link is used for voice wake up, users can set this flag bit and
topology will set the link's 'ignore_suspend' to true.
This ABI update is backward compatible.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Code refactoring. These functions and variables are for configuring
physical DAIs, not only backend DAIs since users may not need DPCM.
So remove 'be' from the function names, and rename variables 'be'
to 'd' or 'dai'.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename the ABI struct and type because they are for configuring physical
DAIs, not only backend DAIs since users may not need DPCM:
- Rename struct snd_soc_tplg_be_dai to snd_soc_tplg_dai.
- Rename type SND_SOC_TPLG_TYPE_BE_DAI to SND_SOC_TPLG_TYPE_DAI.
This code refactoring is backward compatible because:
- Both layout of the struct and type value has no change. Kernel can
find the same type value and map to same data layout.
- This struct is not in ABI v4 at all. Now the user space uses ABI v4.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Just code refactoring. The function soc_tplg_link_create() will
create a front end link, not a physical link. So rename it to
soc_tplg_fe_link_create().
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Topology will find an existing physical link (including BE link for
DPCM) by checking its ID, name and stream name, and configure its physical
audio format and flags.
This support is backward compatible for old ABI v4.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Define the API to find an existing DAI link of the soc card by matching
the ID, name and stream name.
Some cards may use unique ID for each DAI link, so matching ID is enough,
and name or stream name are not necessary. But user need to specify name
or stream name as well if not sure whether link ID is unique since most
cards use 0 as the default link ID.
Topology can use this API to find an existing BE link and configure it.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch renames msm8916_wcd_digital_parse_dt() to
msm8916_wcd_digital_get_clks() as the function is not directly dealing
with dt parsing.
No functional changes done.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the code which is not parsing dt from pm8916_wcd_analog_parse_dt()
to make it clear to reader.
No functional changes done.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 integrated codec has a stereo "Line In" input. Add support for
it to the playback paths.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 has a similar codec to the A10/A20. The PCM parts are very
similar, with different register offsets. The analog paths are very
different. There are more inputs and outputs. The ADC mux has been
replaced with a proper mixer.
This patch adds support for the basic playback path of the A31 codec,
from the DAC to the headphones. Headphone detection, microphone,
signaling, other inputs/outputs and capture will be added later.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the DMA engine API documentation, maxburst denotes the
largest possible size of a single transfer, so as not to overflow
destination FIFOs as explained in this excerpt from dmaengine.h
* @src_maxburst: the maximum number of words (note: words, as in
* units of the src_addr_width member, not bytes) that can be sent
* in one burst to the device. Typically something like half the
* FIFO depth on I/O peripherals so you don't overflow it. This
* may or may not be applicable on memory sources.
* @dst_maxburst: same as src_maxburst but for destination target
* mutatis mutandis.
The TX FIFO is 64 samples deep for stereo, and the RX FIFO is 16
samples deep. So maxburst could be 32 and 8 for TX and RX respectively.
Unfortunately the sunxi DMA controller driver takes maxburst as
the requested burst size, rather than a limit, and returns an error
for unsupported values. The original value was 4, but some later
SoCs do not officially support this burst size.
This patch increases maxburst on the TX side to 8, which is supported
by all variants of the sunxi DMA controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 has a similar codec to the A10/A20. The PCM parts are very
similar, with just different register offsets. The analog paths are
very different. There are more inputs and outputs.
The A31s, A23, and H3 have a similar PCM interface, again with register
offsets slightly rearranged. The analog path controls, while very
similar between them and the A31, have been moved a separate bus which
is accessed through a message box like interface in the PRCM address
range. This would be handled by a separate auxiliary device tied in
through the device tree in its supporting create_card function.
The quirks structure is expanded to include different register offsets
and separate callbacks for creating the ASoC card. The regmap_config,
quirks, and of_device_match tables have been moved to facilitate this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This revises existing comments in the register definition macros
section, and adds a few more, so that readers can clearly identify
the types of control registers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio codec on later Allwinner SoCs have a different layout and
audio path compared to the A10/A20. However the PCM parts are still
the same.
The different layout and audio paths mean we need a different
create_card function for different families, so they can create
DAPM endpoint widgets and routes.
This patch moves the regmap configs, quirks and of_device_id
structures to just before the probe function, so we can, among other
things, include a pointer for the create_card function. None of the
lines of code were changed.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For device opened/closed, we check the D0i3 capability for the device
and invoke skl_tplg_d0i3_get/put, which counts the use case based on the
mode supported.
These counters are then used to decide if the device can enter D0i3 mode
of streaming or non-streaming or no D0i3.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Not all use cases can support Doi3. Only certain use cases like hot word
detection, deep buffering can support D0i3 based on resource requirement.
So, pass the D0i3 capability for the FE/BE copier using topology. This will
be used to take a decision for D0i3 mode entry/exit.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For D0i3, we need to tell DSP to run the pipelines in LP mode. This
information is kept in topology and passed to driver as an attribute
for pipe.
So add a new tuple for lpmode and program the pipe based on value set.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver needs two DSP callback, one to set D0i0 (active) and D0i3
(low-power) states.
Add these callbacks in dsp ops and implement them for broxton platforms.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To set the controller in D0i3 mode, the driver needs to set D0i3C
register after DSP is quiesced. Since the D0iX entry/exit is done by IPC,
add this as callback so that it can be invoked from IPC module.
Signed-off-by: Pardha Saradhi K <pardha.saradhi.kesapragada@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio DSP supports intermediate power states between D0 and D3
states. These states are D0i0 and D0i3 states.
Collectively we refer these two states as D0iX states.
To set or wake up from these states, driver also needs to send an IPC "Set D0iX
IPC" before doing anything else.
Add support for this new IPC messages.
Signed-off-by: Pardha Saradhi K <pardha.saradhi.kesapragada@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the DSP is in low power mode, it needs to be woken up by a "wake" IPC
to set it into the D0 state before we can send any other IPC command.
The call flow is that the driver calls sst_ipc_tx_message_wait() to send any
IPC and this call checks if the device is in low power mode and in that
case we need to send the wake IPC.
So add a new IPC nopm variant which can be called from driver and
doesn't check for power state (as we already know that) and avoids
circular dependency of again checking power state.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The i2s driver was only implementing playback for now. Implement capture to
make sure that's not a limitation anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the remaining update to PCM ABI object of version 5.
The flags will be applied to FE (Front End) links and can also be used
by physical links. The private data is reserved for future extension, so
offset update will add the private data size.
Now user space is using ABI v4, and the previous patch "ASoC: topology:
make PCM backward compatible from ABI v4" can assure the backward
compatibility.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Users start to use topology ABI from v4. ABI v5 updated existing manifest
and PCM elements. Two previous patches can support these ABI updates in a
backward compatible way. So if the topology file from user space is
generated by ABI v4, kernel will no longer quit but continue parsing.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
User space may not always set a valid FE DAI driver's name, FE DAI link's
name, stream name or cpu DAI name. In such cases, there are all ZERO in
these name string buffers of a topology PCM object. This patch will only
duplicate valid name strings for kernel FE DAI driver and DAI link when
creating them from topology, and free the name strings when destroying
them.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for old version 4 of PCMs (FE DAI & DAI links).
Topology ABI v5 added new fields to stream caps and thus changed PCMs.
Since user space may still uses v4, kernel will check the ABI version by
comparing the object size. If user space uses v4 of PCMs, kernel will
create the latest version of PCMs from the old version, and use the new
version internally to create FE DAI & DAI links. Because these new created
PCM elements will be freed later, kernel need duplicate the name strings
of DAI driver and DAI links when creating them.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
add depends on HAS_DMA to Kconfig. This fixes error reported
by kbuild test robot when building for ARCH=m32r:
ERROR: "bad_dma_ops" [sound/soc/bcm/snd-soc-cygnus.ko] undefined!
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While DAPM is mono or single channel, its controls can be shared between
widgets, such as sharing one stereo mixer control between the left and
right channel widgets. An example such as the following routes
[Line In Left]----------<Line In Playback Switch>-------[Left Mixer]
^
^ ^ | ^
(inputs) (paths) <shared stereo mixer control> (outputs)
v v | v
v
[Line In Right]---------<Line In Playback Switch>-------[Right Mixer]
where we have separate widgets and paths for the left and right channels
from "Line In" to "Mixer", but a shared stereo mixer control for the
2 paths.
This patch introduces support for such shared mixer controls, allowing
more than 1 path to be attached to a single stereo control, and being
able to control left/right channels independently.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support double channel shared controls split across 2 registers, one
for each channel, we must be able to update both registers together.
Add a second set of register fields to struct snd_soc_dapm_update, and
update the DAPM control writeback (put) callbacks to support this.
For codecs that use custom events which call into DAPM to do updates,
also clear struct snd_soc_dapm_update before using it, so the second
set of fields remains clean.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes a build error as below which appeared after merging
branch fix/samsung and also proper error messages are restored.
sound/soc/samsung/s3c24xx-i2s.c: In function ‘s3c24xx_iis_dev_probe’:
sound/soc/samsung/s3c24xx-i2s.c:444:8: error: ‘pdata’ undeclared (first use in this function)
sound/soc/samsung/s3c24xx-i2s.c:444:8: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes issues introduced in commit 73f5dfc683
"ASoC: samsung: get access to DMA engine early to defer probe properly"
and indicated by a following compilation warning:
CC [M] sound/soc/samsung/spdif.o
sound/soc/samsung/spdif.c: In function ‘spdif_probe’:
sound/soc/samsung/spdif.c:419:6: warning: ‘filter’ may be used uninitialized
in this function [-Wuninitialized]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AC97 drivers are broken and it seems these have not been used
for a long time. This patch removes the unused code, i.e. Samsung
SoC AC97 controller driver and related machine drivers:
ln2440sbc_alc650, smdk2443_wm9710, smdk_wm9713.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to report the resource request error in
the driver as it is already handled within devm_ioremap_resource().
While at it also drop a redundant variable initialization.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This simplifies the code a bit and removes a hard coded IO memory
region size.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the current probe function the GPIO is acquired after the codec's
bus clock is enabled. However if it fails to acquire the GPIO due to
a deferred probe, it does not disable the bus clock before bailing out.
This would result in the clock being enabled multiple times.
Move the code that enables the bus clock after the part that gets the
GPIO, maintaining a separation between resource acquisition and device
enablement in the probe function.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleans up usage of wrdma_ch and rdma_ch variables into a
common variable dma_ch, As there is no real use of tracking the dma
channel in two different variables based on stream direction.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds module licence to lpass-cpu driver, without this
patch lpass-cpu module would taint with below error:
snd_soc_lpass_cpu: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
snd_soc_lpass_cpu: Unknown symbol regmap_write (err 0)
snd_soc_lpass_cpu: Unknown symbol devm_kmalloc (err 0)
...
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes lpass-platform driver which was broken in v4.9-rc1.
lpass_pcm_data data structure holds information specific to stream.
Holding a single private pointer to it in global lpass_data
will not work, because it would be overwritten by for each pcm instance.
This code was breaking playback when we have both playback and capture
pcm streams, as playback settings are over written by capture settings.
Fix this by moving channel allocation logic out of pcm_new to pcm_open
so that we can store the stream specific information in private_data of
snd_pcm_runtime.
Fixes: 6adcbdcd4b ("ASoC: lpass-platform: don't use snd_soc_pcm_set_drvdata()")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When sun4i_codec_create_card fails, we do not assign a proper error
code to the return value. The return value would be 0 from the previous
function call, or we would have bailed out sooner. This would confuse
the driver core into thinking the device probe succeeded, when in fact
it didn't, leaving various devres based resources lingering.
Make the create_card function pass back a meaningful error code, and
assign it to the return value.
Fixes: 45fb6b6f2a ("ASoC: sunxi: add support for the on-chip codec on
early Allwinner SoCs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings:
sound/soc/codecs/wm8580.c:988:33: warning:
symbol 'wm8580_data' was not declared. Should it be static?
sound/soc/codecs/wm8580.c:992:33: warning:
symbol 'wm8581_data' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for old version 4 of manifest.
Topology ABI v5 added new fields to manifest while user space may still
uses v4. So kernel will check the ABI version by comparing the object
size. If user space uses v4 of manifest, kernel will create a latest
version of manifest from the old one, and use the new one internally and
free it later.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mono ADC Capture Switch control is missing in the driver. So, add it.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove cpu/codec pointer check from asoc_simple_card_canonicalize_dailink()
This is verbose check, and will be issue if CPU name was created by
fmt_single_name() on simple-scu-card.c.
see also asoc_simple_card_canonicalize_cpu()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple sound card family are using very similar style, but because of its
historical reason, there are small differences. For example pointer style,
function name, caller postion etc...
This patch synchronizes style to other simple card family so that be enable
to easy reviewing.
This patch uses dai_link/dai_props instead of links/props.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple sound card family are using very similar style, but because of its
historical reason, there are small differences. For example pointer style,
function name, caller postion etc...
This patch synchronized simple card style to other simple card family
This patch renames asoc_simple_card_priv to simple_card_data,
same as other simple card family.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple sound card family are using very similar style, but because of its
historical reason, there are small differences. For example pointer style,
function name, caller postion etc...
This patch synchronized simple card style to other simple card family
Current simple-scu-card function naming is different from other simple card
family. And related to it, the necessary operation position is also
different. This patch synchronize these to other simple card family.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current register name of "SSICKR" was came from R-Car Gen1
which is very old style. It is called as "BRGCKR" on R-Car Gen2/Gen3.
Let's rename it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some controllers support power modes which can't communicate using IPC.
So add a callback to check and wake DSP before sending IPC and then put
to sleep if it is in these power modes.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a DAI specifies "#sound-dai-cells = <0>" in device-tree then
hdmi_of_xlate_dai_name() will be called with zero args, which it isn't
implemented to cope with. The resulting use of an uninitialised variable
for the id will usually result in an error like:
asoc-simple-card sound: parse error -11
asoc-simple-card: probe of sound failed with error -11
Fix this by using and id of zero if no arg is provided.
Fixes: 9731f82d60 ("ASoC: hdmi-codec: enable multi probe for same device")
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC Samsung sub-drivers tried to get access to their DMA engine
controllers as a last step in driver probe. If a DMA engine was not
available yet, samsung_asoc_dma_platform_register() function ended in
-EPROBE_DEFER, but the driver already registered its component to ASoC
core. This patch moves samsung_asoc_dma_platform_register() call before
registering any components, to the common place, where driver was gathering
all needed resources.
In case of Samsung Exynos i2s driver the issue was even worse. The driver
managed already to register its secondary DAI platform device before
even getting the DMA engine access. That together with -EPROBE_DEFER error
code from samsung_i2s_probe() immediately triggered another round of
deferred probe retry and in turn endless loop of driver probing.
This patch fixes broken boot on Odroid XU3 and other Exynos5422-based
boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch is adding debug information related to SST FW version.
Signed-off-by: Sebastien Guiriec <sebastien.guiriec@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
da7219 output (for headset capture) should be set to high-impedance when
not in use, since it will otherwise interfere with output from other
codecs attached to the same DAI.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DPIB is read currently from a buffer position in memory (indicated by
the registers DPIB[U|L]BASE).Driver reads the position buffer on BDL
completion interrupts to report the DMA position. But the BDL completion
interrupt only indicates the last DMA transfer of the buffer is
completed at the Intel HD Audio subsystem boundary. The periodic DMA
Position-in-Buffer writes may be scheduled at the same time or later
than the MSI and does not guarantee to reflect the position of the last
buffer that was transferred.
Whereas DPIB register in HDA space(vendor specific register indicated by
SDxDPIB) reflects the actual data that is transferred. Hence update the
position based on DPIB for playback.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's difficult to guess from bunch of "ret=-121" errors what driver and
device actually caused them. Since struct i2c_client has the dev pointer
use that for dev_err() with meaningful error message.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI codec is required to be powered up before controller initialization
for successful enumeration of codec. If the probe fails it needs to be
powered off to balance the power state of HDMI codec.
This fix balances the reference count in the error path before turning
off the codec.
Reported-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Sodhi, VunnyX <vunnyx.sodhi@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 4c5d146929 ("ASoC: max98504: Add max98504 speaker amplifier
driver") added new max98504, but this patch didn't add it to
SND_SOC_ALL_CODECS. This patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SRC (= Sampling Rate Converter) is supporting
SYNC mode and ASYNC mode. Current src.c cares SRC if FIN != FOUT.
Here, SYNC mode will be used for tweak, so it will be used
even FIN = FOUT. This patch enables SRC sync in such situation
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Tested-by: Yuichi Takagi <yuichi.takagi.uh@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound SSIU has SSI_SYS_STATUS register whick will
be changed if over/under run was occurred.
Current rsnd driver is handling over/under run error on SSI/SRC,
but doesn't on SSIU.
HW guys can't guarantee correct behavior if it already had error bit
on status register when it start.
Thus, it should be cleared every start timing. This patch do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SCU_SYS_STATUSx is the register that writing 1 initializes the bit,
and writing 0 is ignored. So, it should use rsnd_mod_write()
instead of rsnd_mod_bset(), otherwise all bit will be cleared.
Thanks Shimoda-san
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car Gen1 didn't have SSIU IP, and it was part of SRU.
In Gen2, SSIU was created and it has original register.
Let's cleanup rsnd_reg for SSIU, because this driver
doesn't support Gen1 SRU any more.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Gen1 support had been removed. "Gen2 only" comment is
no longer needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the compressed ops run on the platform side of things we should
really access the driver data through the platform pointer rather than
the CODEC pointer. As the compressed DAIs in our systems always connect
our CODEC to our platform this has never been an issue, but should still
be corrected. Additionally it clears the way for future core refactoring
work.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 31833ead95 ("ASoC: arizona: Move request of speaker IRQs into bus probe")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver is completely depends on CONFIG_OF
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some registers accesses are done in atomic context.
Enable fast io to use spinlock instead of mutex to protect access.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
stih416 is no more supported, clean associated code.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If 'IEC958 Playback Default' control is updated during playback,
Channel status needs to be set according to the runtime structure.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reset is common to player and reader, migrate function in sti_uniperif.c
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing error messages.
Propagate error of uni_reader_init and uni_reader_init.
Add return at end of dev_err strings.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a check for validity of one of ids in mxs_saif_probe(),
while array dereferece is made by the other id.
The patch adds the check for the second saif id.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
"*val" is a u64. It definitely looks like we intend to use the high 32
bits as well.
Fixes: 700a9a63f9 ("ASoC: Intel: Skylake: Add module instance id generation APIs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Kranthi G <gudishax.kranthikumar@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is more idiomatic to request all resources in the bus level probe,
this patch moves the request of the DSP compressed data IRQ from the
ASoC level probe into the bus level probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is more idiomatic to request all resources in the bus level probe,
this patch moves the request of the speaker thermal event IRQs from the
ASoC level probe into the bus level probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CS35L34_CHIP_ID is not a register address, it's the value read from
CS35L34_DEVID_AB/CD/E registers.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
pr_err() are replaced with dev_err() so information about
device the error logs refer to is also included.
pr_debug() at beginning of each function are removed
as they are likely very rarely used and can always be
added again when doing any serious debugging.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the s3c24xx-dma is converted to use DMA map we can rely on the
DMA subsystem to match DMA channels and slave devices, rather than
passing DMA details from platform_data.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 194c7dea00
"ASoC: dmaengine: add custom DMA config to snd_dmaengine_pcm_config"
custom DMA channels can be also specified in chan_names[] field of
struct snd_dmaengine_pcm_config. This patch removes chan_name field
of struct snd_dmaengine_dai_dma_data as it is now unused.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates the I2S drivers to always use chan_names[] field
of struct snd_dmaengine_pcm_config for specifying DMA channel names,
rather than using struct snd_dmaengine_dai_dma_data.
This allows us to subsequently drop the
SND_DMAENGINE_PCM_FLAG_CUSTOM_CHANNEL_NAME flag, now when the last
use of that flag is removed.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't manually enable cache_bypass for reading the ID registers they
don't have a default anyway so the first read will always hit the
hardware. The old code worked this is simply the more standard way
to implement this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rather than manually enabling cache bypass when reading the ID registers
simply remove the default which will cause the first read to go to the
hardware. The old code worked this is simply the more standard way to
implement this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rather than manually enabling cache bypass when reading the ID registers
simply remove the default which will cause the first read to go to the
hardware. The old code worked this is simply the more standard way to
implement this. There is a comment included in the code that claims the
chip ID register also contains the right input volume, however this is
clearly not the case from the rest of the driver. Further investigation
reveals exactly the same comment in the wm8962 driver, where this is the
case, so this is almost certainly a copy and paste error from when the
driver was created.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas Sound driver requests DMA channel when .probe timing,
and release it when .remove timing. And use DMA on .start/.stop
But, Audio DMAC power ON was handled when request timing (= .probe),
and power OFF was when release timing (= .remove).
This means Audio DMAC power is always ON during driver was enabled.
To fixup this issue, it should request/release DMA channel on each
playback/recorde timing.
But, DMA channel request/release function uses mutex lock inside.
This means it will breaks current spinlock's interrupt protect.
To solve this issue, DMA channel request/release function needs to
be called from non-spinlock area. This patch adds its callback.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_dmaen_start() is calling of_node_put() for np,
but it is not needed if it goes through this loop.
This patch tidyup it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA mod is now connected to stream via rsnd_dai_connect().
This means DMA mod can use .remove for its clearance.
rsnd_dma_detach() is no longer needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI will use DMA mode, and migh be fallback to PIO mode.
Using devm_request_irq() makes its operation more complex when
it fallbacks to PIO mode.
Let's use manual request_irq()/free_irq()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas Sound driver is based on DeviceTree, and no one is
using this driver from non DT. Non-DT support is no longer needed.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to the DMIC that needs time to initial after the MCLK is provided, the
field of delay time is implemented by the platform data.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Gather all driver's private variables in common data structure
and allocate the data structure dynamically.
Also unused ENFORCE_RATES symbol and local variable (leftovers
from an erroneous rebase) are removed.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- first slice of the gvt device model (Zhenyu et al)
- compression support for gpu error states (Chris)
- sunset clause on gpu errors resulting in dmesg noise telling users
how to report them
- .rodata diet from Tvrtko
- switch over lots of macros to only take dev_priv (Tvrtko)
- underrun suppression for dp link training (Ville)
- lspcon (hmdi 2.0 on skl/bxt) support from Shashank Sharma, polish
from Jani
- gen9 wm fixes from Paulo&Lyude
- updated ddi programming for kbl (Rodrigo)
- respect alternate aux/ddc pins (from vbt) for all ddi ports (Ville)
* tag 'drm-intel-next-2016-10-24' of git://anongit.freedesktop.org/drm-intel: (227 commits)
drm/i915: Update DRIVER_DATE to 20161024
drm/i915: Stop setting SNB min-freq-table 0 on powersave setup
drm/i915/dp: add lane_count check in intel_dp_check_link_status
drm/i915: Fix whitespace issues
drm/i915: Clean up DDI DDC/AUX CH sanitation
drm/i915: Respect alternate_ddc_pin for all DDI ports
drm/i915: Respect alternate_aux_channel for all DDI ports
drm/i915/gen9: Remove WaEnableYV12BugFixInHalfSliceChicken7
drm/i915: KBL - Recommended buffer translation programming for DisplayPort
drm/i915: Move down skl/kbl ddi iboost and n_edp_entires fixup
drm/i915: Add a sunset clause to GPU hang logging
drm/i915: Stop reporting error details in dmesg as well as the error-state
drm/i915/gvt: do not ignore return value of create_scratch_page
drm/i915/gvt: fix spare warnings on odd constant _Bool cast
drm/i915/gvt: mark symbols static where possible
drm/i915/gvt: fix sparse warnings on different address spaces
drm/i915/gvt: properly access enabled intel_engine_cs
drm/i915/gvt: Remove defunct vmap_batch()
drm/i915/gvt: Use common mapping routines for shadow_bb object
drm/i915/gvt: Use common mapping routines for indirect_ctx object
...
Unfortunately, I seem to have missed a case where an IRQ safe spinlock was
required, in samsung_i2s_dai_remove, when I fixed up the other calls in
this patch:
316fa9e09a ("ASoC: samsung: Use IRQ safe spin lock calls")
This causes a lockdep warning when unbinding and rebinding the audio card:
[ 104.357664] CPU0 CPU1
[ 104.362174] ---- ----
[ 104.366692] lock(&(&pri_dai->spinlock)->rlock);
[ 104.371372] local_irq_disable();
[ 104.377283] lock(&(&substream->self_group.lock)->rlock);
[ 104.385259] lock(&(&pri_dai->spinlock)->rlock);
[ 104.392469] <Interrupt>
[ 104.395072] lock(&(&substream->self_group.lock)->rlock);
[ 104.400710]
[ 104.400710] *** DEADLOCK ***
Fixes: ce8bcdbb61 ("ASoC: samsung: i2s: Protect more registers with a spinlock")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ak4641 driver only has a few register defines. As they are only used in
the one main driver file there is not really a need to keep them in a
separate header.
Moving them to the main source file allows to remove the now empty header
file completely.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The last user was removed in commit 4f534777c1 ("ASoC: ak4641: Convert to
direct regmap API usage").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. This driver was merged after the change of DAIs are
matched was made and the IDs were never used and presumably never will be,
so remove them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The es8328 drivers seems to have used the wm8753 driver as a template. Its
header file contains a few defines that are copied verbatim from the wm8753
header that do not really apply to this driver and are unused. So remove
those defines. This seems safe as they deal with PLL and clock divider
settings and the es8328 driver neither implements a set_pll() nor a
set_clkdiv() callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. The last user of these defines was removed in commit
f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support"). So
remove the defines as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. This particular ID was never used and presumably never
will be, so remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. The last user of these defines was removed in commit
f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support"). So
remove the defines as well.
This also means the wm9705.h file no longer has any content and can be
removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. These particular IDs were never used and presumably
never will be, so remove them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. The last user of these defines was removed in commit
f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support"). So
remove the defines as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. The last user of these defines was removed in commit
f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support"). So
remove the defines as well.
This also means the wm9712.h file no longer has any content and can be
removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_ops structures that are only stored in the ops field of a
snd_soc_dai_link structure. This field is declared const, so snd_soc_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_dai_link e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i, e;
position p;
@@
struct snd_soc_dai_link e[] = { ..., { .ops = &i@p, }, ..., };
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_soc_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_ops i = { ... };
// </smpl>
The effect on the layout of the .o files is shown by the following output of
the size command, first before then after the transformation:
text data bss dec hex filename
8748 1024 0 9772 262c sound/soc/fsl/fsl-asoc-card.o
8812 952 0 9764 2624 sound/soc/fsl/fsl-asoc-card.o
text data bss dec hex filename
4165 264 8 4437 1155 sound/soc/fsl/imx-wm8962.o
4229 200 8 4437 1155 sound/soc/fsl/imx-wm8962.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_ops structures that are only stored in the ops field of a
snd_soc_dai_link structure. This field is declared const, so snd_soc_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_dai_link e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i, e;
position p;
@@
struct snd_soc_dai_link e[] = { ..., { .ops = &i@p, }, ..., };
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_soc_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_ops i = { ... };
// </smpl>
The effect on the layout of the .o files is shown by the following output
of the size command, first before then after the transformation:
text data bss dec hex filename
4500 696 0 5196 144c sound/soc/generic/simple-card.o
4564 632 0 5196 144c sound/soc/generic/simple-card.o
text data bss dec hex filename
3018 608 0 3626 e2a sound/soc/generic/simple-scu-card.o
3074 544 0 3618 e22 sound/soc/generic/simple-scu-card.o
text data bss dec hex filename
4148 2448 768 7364 1cc4 sound/soc/intel/boards/bdw-rt5677.o
4212 2384 768 7364 1cc4 sound/soc/intel/boards/bdw-rt5677.o
text data bss dec hex filename
5403 4628 384 10415 28af sound/soc/intel/boards/bxt_da7219_max98357a.o
5531 4516 384 10431 28bf sound/soc/intel/boards/bxt_da7219_max98357a.o
text data bss dec hex filename
5275 4496 384 10155 27ab sound/soc/intel/boards/bxt_rt298.o
5403 4368 384 10155 27ab sound/soc/intel/boards/bxt_rt298.o
text data bss dec hex filename
10017 2344 48 12409 3079 sound/soc/intel/boards/bytcr_rt5640.o
10145 2232 48 12425 3089 sound/soc/intel/boards/bytcr_rt5640.o
text data bss dec hex filename
3719 2356 0 6075 17bb sound/soc/intel/boards/bytcr_rt5651.o
3847 2244 0 6091 17cb sound/soc/intel/boards/bytcr_rt5651.o
text data bss dec hex filename
3598 2392 0 5990 1766 sound/soc/intel/boards/cht_bsw_max98090_ti.o
3726 2280 0 6006 1776 sound/soc/intel/boards/cht_bsw_max98090_ti.o
text data bss dec hex filename
5343 3624 16 8983 2317 sound/soc/intel/boards/cht_bsw_rt5645.o
5471 3496 16 8983 2317 sound/soc/intel/boards/cht_bsw_rt5645.o
text data bss dec hex filename
4662 2592 384 7638 1dd6 sound/soc/intel/boards/cht_bsw_rt5672.o
4790 2464 384 7638 1dd6 sound/soc/intel/boards/cht_bsw_rt5672.o
text data bss dec hex filename
1595 2528 0 4123 101b sound/soc/intel/boards/haswell.o
1659 2472 0 4131 1023 sound/soc/intel/boards/haswell.o
text data bss dec hex filename
6272 4760 416 11448 2cb8 sound/soc/intel/boards/skl_nau88l25_max98357a.o
6464 4568 416 11448 2cb8 sound/soc/intel/boards/skl_nau88l25_max98357a.o
text data bss dec hex filename
7075 4888 416 12379 305b sound/soc/intel/boards/skl_nau88l25_ssm4567.o
7267 4696 416 12379 305b sound/soc/intel/boards/skl_nau88l25_ssm4567.o
text data bss dec hex filename
5659 4496 384 10539 292b sound/soc/intel/boards/skl_rt286.o
5787 4368 384 10539 292b sound/soc/intel/boards/skl_rt286.o
text data bss dec hex filename
1721 2048 0 3769 eb9 sound/soc/kirkwood/armada-370-db.o
1769 1976 0 3745 ea1 sound/soc/kirkwood/armada-370-db.o
text data bss dec hex filename
1363 1792 0 3155 c53 sound/soc/mxs/mxs-sgtl5000.o
1427 1728 0 3155 c53 sound/soc/mxs/mxs-sgtl5000.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_ops structures that are only stored in the ops field of a
snd_soc_dai_link structure. This field is declared const, so snd_soc_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_dai_link e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i, e;
position p;
@@
struct snd_soc_dai_link e[] = { ..., { .ops = &i@p, }, ..., };
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_soc_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_ops i = { ... };
// </smpl>
The effect on the layout of the .o files is shown by the following output of
the size command, first before then after the transformation:
text data bss dec hex filename
3143 1888 384 5415 1527 sound/soc/tegra/tegra_alc5632.o
3191 1840 384 5415 1527 sound/soc/tegra/tegra_alc5632.o
text data bss dec hex filename
3672 2176 768 6616 19d8 sound/soc/tegra/tegra_max98090.o
3720 2128 768 6616 19d8 sound/soc/tegra/tegra_max98090.o
text data bss dec hex filename
2770 1856 384 5010 1392 sound/soc/tegra/tegra_rt5640.o
2818 1808 384 5010 1392 sound/soc/tegra/tegra_rt5640.o
text data bss dec hex filename
4412 2176 768 7356 1cbc sound/soc/tegra/tegra_rt5677.o
4460 2128 768 7356 1cbc sound/soc/tegra/tegra_rt5677.o
text data bss dec hex filename
2442 1536 0 3978 f8a sound/soc/tegra/tegra_sgtl5000.o
2490 1480 0 3970 f82 sound/soc/tegra/tegra_sgtl5000.o
text data bss dec hex filename
2105 1536 0 3641 e39 sound/soc/tegra/tegra_wm8753.o
2153 1480 0 3633 e31 sound/soc/tegra/tegra_wm8753.o
text data bss dec hex filename
3755 1888 768 6411 190b sound/soc/tegra/tegra_wm8903.o
3803 1840 768 6411 190b sound/soc/tegra/tegra_wm8903.o
text data bss dec hex filename
2121 1536 0 3657 e49 sound/soc/tegra/trimslice.o
2169 1480 0 3649 e41 sound/soc/tegra/trimslice.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_ops structures that are only stored in the ops field of a
snd_soc_dai_link structure. This field is declared const, so snd_soc_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_dai_link e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i, e;
position p;
@@
struct snd_soc_dai_link e[] = { ..., { .ops = &i@p, }, ..., };
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_soc_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_ops i = { ... };
// </smpl>
The effect on the layout of the .o file is shown by the following output of
the size command, first before then after the transformation:
text data bss dec hex filename
1420 512 0 1932 78c sound/soc/qcom/storm.o
1484 456 0 1940 794 sound/soc/qcom/storm.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_ops structures that are only stored in the ops field of a
snd_soc_dai_link structure. This field is declared const, so snd_soc_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_dai_link e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i, e;
position p;
@@
struct snd_soc_dai_link e[] = { ..., { .ops = &i@p, }, ..., };
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_soc_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_ops i = { ... };
// </smpl>
The effect on the layout of the .o files is shown by the following output
of the size command, first before then after the transformation:
text data bss dec hex filename
5027 2488 416 7931 1efb sound/soc/rockchip/rk3399_gru_sound.o
5219 2312 416 7947 1f0b sound/soc/rockchip/rk3399_gru_sound.o
text data bss dec hex filename
3499 1648 384 5531 159b sound/soc/rockchip/rockchip_max98090.o
3563 1584 384 5531 159b sound/soc/rockchip/rockchip_max98090.o
text data bss dec hex filename
3455 1536 384 5375 14ff sound/soc/rockchip/rockchip_rt5645.o
3519 1480 384 5383 1507 sound/soc/rockchip/rockchip_rt5645.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_ops structures that are only stored in the ops field of a
snd_soc_dai_link structure. This field is declared const, so snd_soc_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_dai_link e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i, e;
position p;
@@
struct snd_soc_dai_link e[] = { ..., { .ops = &i@p, }, ..., };
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_soc_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_ops i = { ... };
// </smpl>
The effect on the layout of the .o file is shown by the following output of
the size command, first before then after the transformation:
text data bss dec hex filename
2611 1536 0 4147 1033 sound/soc/atmel/atmel_wm8904.o
2675 1480 0 4155 103b sound/soc/atmel/atmel_wm8904.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_ops structures that are only stored in the ops field of a
snd_soc_dai_link structure. This field is declared const, so snd_soc_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_dai_link e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i, e;
position p;
@@
struct snd_soc_dai_link e[] = { ..., { .ops = &i@p, }, ..., };
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_soc_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_ops i = { ... };
// </smpl>
The effect on the layout of the .o file is shown by the following output of
the size command, first before then after the transformation:
text data bss dec hex filename
3865 2784 384 7033 1b79 sound/soc/intel/boards/broadwell.o
3929 2720 384 7033 1b79 sound/soc/intel/boards/broadwell.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a power saving mechanism in rt5670. It will turn off some
unused power when MCLK is not present. We call that "MCLK detection"
and it should be enabled by default.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a power saving mechanism in rt5640. It will turn off some
unused power when MCLK is not present. We call that "MCLK detection"
and it should be enabled by default.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I rand into a new build error with SND_MMP_SOC_BROWNSTONE:
warning: (SND_MMP_SOC_BROWNSTONE && SND_SOC_SAMSUNG_SMDK_WM8994 && SND_SOC_SMDK_WM8994_PCM && SND_SOC_LITTLEMILL) selects MFD_WM8994 which has unmet direct dependencies (HAS_IOMEM && I2C)
drivers/mfd/wm8994-core.c:688:1: error: data definition has no type or storage class [-Werror]
drivers/mfd/wm8994-core.c:688:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
I don't see why this never showed up before, as the dependency seems to
have been missing since the symbol was first introduced several years
ago. This adds a dependency like the other drivers have.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warning:
sound/soc/rockchip/rk3399_gru_sound.c:41:14: warning:
symbol 'rt5514_dmic_delay' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Smatch reports below warnings:
bxt_da7219_max98357a.c:352:9: warning: obsolete array initializer,
use C99 syntax
An earlier commit cleaned up similar warnings, however, a recent
commit 43c02ede76 ("ASoC: Intel: Add DMIC channel constraint for
bxt machine") re-introduced the older initializer style. So fix
this warning to make the code consistent.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the wm8581 codec to the wm8580 driver.
The wm8581 codec hardware adds a fourth DAC and otherwise is
compatible with the wm8580 codec.
of_device_id data is used to allow the driver to select the
suitable DAC count specified in the device tree codec selection.
The wm8580_driver_data struct is used to store the number of DACs.
The snd_soc_dai_driver no longer lists the channels_max for the
playback substream. This variable is set during the i2c probe
from the of_device_id supplied wm8580_driver_data struct.
With knowledge of the number of DACs in use, the DAC4 controls,
widgets and routes are added as required for DAC4.
The device tree documentation for the wm8580 is altered to list
the wm8581 codec support, as is the Kconfig file.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now, we have for_each_rsnd_mod(), let's use it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using too complex macro for for-loop of each mod.
rsnd_dai_call() is especially defined as very complex macro.
It is easier to read just a little bit by using for_each_rsnd_mod_xxx()
and new rsnd_status_update()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using too complex macro for for-loop of each mod.
In order to simplify this issue, this patch adds new rsnd_mod_next()
which is non-macro.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 1a5658c213 ("ASoC: rsnd: count .probe/.remove for
rsnd_mod_call()") solved multi-resource-free issue, by putting
.probe/.remove under count control. But,it breaks sound mixing case
(if it was used under DPCM). In such case, it uses MIXn/DVCn/SSIn,
and these should be always probed.
This patch reverted above patch, and solved the same issue by
modifing _rsnd_kctrl_remove() function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a power saving mechanism in rt5660. It will turn off some
unused power when MCLK is not present. We call that "MCLK detection"
and it should be enabled by default.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to multi codec, as the msm8916 codec is now
split into two codecs, Analog and Digital.
Also update the bindings and example to show that the card supports
multicodec.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd codec is found in Qualcomm msm8916 and apq8016 processors.
This codec IP is split in to two parts(Digital & Analog).
Analog part is integrated in to PMIC PM8916 and the digital part is
integrated into Application processor. Data transfer between Analog and
Digital Die is done via a internal bus called PDM.
This patch adds support to Digital part of the Codec which is integrated
into Application Processor.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd codec is found in Qualcomm msm8916 and apq8016 processors.
This codec IP is split in to two parts (Digital & Analog).
Analog part is integrated in to PMIC PM8916 and the digital part is
integrated into Application processor. Data transfer between Analog and
Digital Die is done via a internal bus called PDM.
This patch adds support to Analog part of the Codec which is integrated
into PMIC PM8916.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
skl_probe() releases a runtime pm ref unconditionally wheras
skl_remove() acquires one only if the device is wakeup capable.
Thus if the device is not wakeup capable, unloading and reloading
the module will result in the refcount being decreased below 0.
Fix it.
Fixes: d8c2dab838 ("ASoC: Intel: Add Skylake HDA audio driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "rt5668" codec supported in this driver is actually a revision
of "rt5663". So the patch is renamed to "rt5663 v2"
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the regmap conversion ac97_read/ac97_write are just simple wrappers
around snd_soc_read/snd_soc_write. Use those instead directly and remove
the wrappers.
Also use snd_soc_update_bits() where appropriate.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the wm9712 driver still uses custom snd_soc_codec_driver IO
callbacks. This has been deprecated for a while, so convert the wm9705
driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst ultimately we would like to move all the clocking over to the
clock framework, as an intermediate step to get people going for now
enable the source clocks for FLLs as they are powered up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst ultimately we would like to move all the clocking over to the
clock framework, as an intermediate step to get people going for now
gating the source clocks for SYSCLK/ASYNCCLK when they are configured
to come directly from an MCLK pin.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt298_jack_detect may be called before card is instantiated. And
snd_soc_dapm_force_enable_pin will not work in that case. So, update
bit manually by regmap_update_bits.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the regmap conversion ac97_read/ac97_write are just simple wrappers
around snd_soc_read/snd_soc_write. Use those instead directly and remove
the wrappers. Also use snd_soc_update_bits() were appropriate.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the wm9712 driver still uses custom snd_soc_codec_driver IO
callbacks. This has been deprecated for a while, so convert the wm9712
driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates Jack type bitmask to include SND_JACK_LINEOUT while
creating a new jack, so that LINEOUT events are reported properly.
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial commit of the Cirrus Logic cs35l34 8V boosted class D
amplifier.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We increment "i" before printing the debug statement. That makes it
the wrong sleep_time[] information and Smatch complains that the last
increment could be beyond the end of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's been over two months, git definitely lost it's marbles. Conflicts
resolved by picking our version, plus manually checking the diff with
the parent in drm-intel-next-queued to make sure git didn't do
anything stupid. It did, so I removed 2 occasions where it
double-inserted a bit of code. The diff is now just
- kernel-doc changes
- drm format/name changes
- display-info changes
so looks all reasonable.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A good practice is to prefix the names of functions by the name
of the subsystem.
The kthread worker API is a mix of classic kthreads and workqueues. Each
worker has a dedicated kthread. It runs a generic function that process
queued works. It is implemented as part of the kthread subsystem.
This patch renames the existing kthread worker API to use
the corresponding name from the workqueues API prefixed by
kthread_:
__init_kthread_worker() -> __kthread_init_worker()
init_kthread_worker() -> kthread_init_worker()
init_kthread_work() -> kthread_init_work()
insert_kthread_work() -> kthread_insert_work()
queue_kthread_work() -> kthread_queue_work()
flush_kthread_work() -> kthread_flush_work()
flush_kthread_worker() -> kthread_flush_worker()
Note that the names of DEFINE_KTHREAD_WORK*() macros stay
as they are. It is common that the "DEFINE_" prefix has
precedence over the subsystem names.
Note that INIT() macros and init() functions use different
naming scheme. There is no good solution. There are several
reasons for this solution:
+ "init" in the function names stands for the verb "initialize"
aka "initialize worker". While "INIT" in the macro names
stands for the noun "INITIALIZER" aka "worker initializer".
+ INIT() macros are used only in DEFINE() macros
+ init() functions are used close to the other kthread()
functions. It looks much better if all the functions
use the same scheme.
+ There will be also kthread_destroy_worker() that will
be used close to kthread_cancel_work(). It is related
to the init() function. Again it looks better if all
functions use the same naming scheme.
+ there are several precedents for such init() function
names, e.g. amd_iommu_init_device(), free_area_init_node(),
jump_label_init_type(), regmap_init_mmio_clk(),
+ It is not an argument but it was inconsistent even before.
[arnd@arndb.de: fix linux-next merge conflict]
Link: http://lkml.kernel.org/r/20160908135724.1311726-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/1470754545-17632-3-git-send-email-pmladek@suse.com
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mismatching stream names in DAPM route and widget definitions are
causing compilation errors. Fixing these names allows the cs4270
driver to compile and function.
[Errors must be at probe time not compile time -- broonie]
Signed-off-by: Murray Foster <mrafoster@gmail.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The Intel Haswell audio support fails to link if
CONFIG_SND_SOC_INTEL_SST_FIRMWARE is disabled:
sst-haswell-dsp.c: undefined reference to `sst_mem_block_register'
sst-haswell-dsp.c: undefined reference to `sst_mem_block_unregister_all'
sst-haswell-dsp.c: undefined reference to `sst_module_alloc_blocks'
sst-haswell-dsp.c: undefined reference to `sst_module_free'
sst-haswell-dsp.c: undefined reference to `sst_module_new'
sst-haswell-pcm.c: undefined reference to `sst_module_get_from_id'
sst-haswell-pcm.c: undefined reference to `sst_module_runtime_restore'
sst-haswell-pcm.c: undefined reference to `sst_module_runtime_save'
ERROR: "sst_block_alloc_scratch" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_block_free_scratch" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_dsp_dma_copyfrom" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_dsp_dma_copyto" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_dsp_dma_get_channel" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_dsp_dma_put_channel" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_dsp_free" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_dsp_get_offset" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_dsp_new" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_fw_free_all" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_fw_new" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_fw_reload" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_fw_unload" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_module_runtime_alloc_blocks" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_module_runtime_get_from_id" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
ERROR: "sst_module_runtime_new" [sound/soc/intel/haswell/snd-soc-sst-haswell-pcm.ko] undefined!
This moves the 'select' statement from two of the three haswell based users
into the line that is used by all of them, so make it harder to get wrong
and to fix the existing randconfig regressions.
Fixes: 2d995e5dc2 ("ASoC: Intel: boards: Add bdw-rt5677 machine driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates Jack type bitmask to include SND_JACK_LINEOUT while
creating a new jack, so that LINEOUT events are reported properly.
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DPIB is read currently from a buffer position in memory (indicated by
the registers DPIB[U|L]BASE).Driver reads the position buffer on BDL
completion interrupts to report the DMA position. But the BDL completion
interrupt only indicates the last DMA transfer of the buffer is
completed at the Intel HD Audio subsystem boundary. The periodic DMA
Position-in-Buffer writes may be scheduled at the same time or later
than the MSI and does not guarantee to reflect the position of the last
buffer that was transferred.
Whereas DPIB register in HDA space(vendor specific register indicated by
SDxDPIB) reflects the actual data that is transferred. Hence update the
position based on DPIB for playback.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently on some headsets slight pops can be heard during DAPM
power-up/down. This can also be witnessed during the HP detect
procedure. This patch addresses the issue by adjusting DAPM power
sequencing slightly, the introduction of delays and use of
minimum HP gain to avoid such noise artefacts.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The set_bias_level toggles the PDN signal when entering
SND_SOC_BIAS_STANDBY and SND_SOC_BIAS_OFF. However this has no effect and
actually breaks things down (tested with TAS5717) due to the following
reasons:
1) holding down PDN does not save power but holding down RST does
2) now hard mute via register 0x5 is implemented and therefore it is no
longer needed to toggle PDN to enter all channel shut down
3) in order to leave PDN it is required to toggle the RST signal (see
TAS5721 datasheet), which was not implemented
4) toggling PDN as implemented actually mutes PWMs and there is no audio
output (tested on TAS5717)
For these reasons remove the PDN signal toggling and just initialize it to
inactive in probe().
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
TAS5721 datasheet recommends to wait at least 13.5ms after deasserting the
RESET signal. For TAS5717 this time is only 12ms, which was the original
value in the code.
Extend the wait time after deasserting RESET from 12 to 13.5ms to comply
with the TAS5721 specification.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Channel 1 and 2 Mixer Volume controls (registers 0x72/0x73 and 0x76/0x77)
were wrongly assigned to tas5711_controls in commit f252d2346022
("ASoC: tas571x: add input channel mixer for TAS5717/19")
Therefore move them to tas5717_controls.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Wait extra 50ms after writing the oscillator trim register in probe(), as
recommended by the TAS5721 and TAS5711 datasheets.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Apart from the cleanups done by Morimoto-san this has very much been a
driver focused release with very little generic change:
- A big factoring out of the simple-card code to allow it to be shared
more with the rcar generic card from Kuninori Morimoto.
- Removal of some operations duplicated on the CODEC level, again by
Kuninori Morimoto.
- Lots more machine support for x86 systems.
- New drivers for Nuvoton NAU88C10, Realtek RT5660 and RT5663.
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJX7pEPExxicm9vbmllQGtlcm5lbC5vcmcACgkQJNaLcl1Uh9Du
Fgf+MAOLDX8z7TbxAM4TnpPO7pRYF+wR+AWamVoUnHrq+gdsUkcKbnTlE8PP05Sp
VDf/ugCMcAQoYrrXPPiZLLB6YsJf2eXjlrTeF5eG/oHRC0mBeM/U6nHblNltFPKl
clV5jTm8Rq/I0AHAiYeTDetQsypK3eVjJ0PZLdenVWF+kL/+aTJ4GXIGgH27aSQC
7lwQZBRWfvGyE/IRu2NNXTPMNSaos/JtLh2/Y2qkWVEQ8YYwFxgRkfCRDHbFk2fK
8/mdWWlaBrApZN8t/RlJxo6rxuQGUn01HFvLpRK1N0EMuLWaTUFHQZtUV/KF/JSz
6Gj4tPLvDke0f4N2tIwoF9quXA==
=qgCG
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.9
Apart from the cleanups done by Morimoto-san this has very much been a
driver focused release with very little generic change:
- A big factoring out of the simple-card code to allow it to be shared
more with the rcar generic card from Kuninori Morimoto.
- Removal of some operations duplicated on the CODEC level, again by
Kuninori Morimoto.
- Lots more machine support for x86 systems.
- New drivers for Nuvoton NAU88C10, Realtek RT5660 and RT5663.
The recent series of changes to the caching in the SSI driver have
caused a number of problems to appear in some test systems. These are
still not fully understood but we're coming up to the merge window so
for now let's revert commit 7de2763d9b (ASoC: fsl_ssi: Remove
.num_reg_defaults_raw from regmap_config) as backing that out seems to
resolve the problem on affected systems.
Reported-by: Maciej S. Szmigiero" <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Currently there is a memory leak of module on a ENOMEM return path.
Fix this by kfree'ing module before returning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds SNDRV_PCM_TRIGGER_SUSPEND/RESUME.
Otherwise, it breaks rsnd driver internal start/stop counter
when suspend/resume. This issue was reported/tested by Hiep
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
