This helps in reducing code in .remove callbacks and sometimes
dropping .remove callbacks entirely.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
With the introduction of the ISA_BUS_API Kconfig option, ISA-style
drivers may be built for X86_64 architectures. This patch changes the
ISA Kconfig option dependency of the WinSystems EBC-C384 watchdog timer
driver to ISA_BUS_API, thus allowing it to build for X86_64 as it is
expected to.
Cc: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull watchdog updates from Wim Van Sebroeck:
- add support for Fintek F81865 Super-IO chip
- add support for watchdogs (RWDT and SWDT) found on RCar Gen3 based
SoCs from Renesas
- octeon: Handle the FROZEN hot plug notifier actions
- f71808e_wdt fixes and cleanups
- some small improvements in code and documentation
* git://www.linux-watchdog.org/linux-watchdog:
MAINTAINERS: Add file patterns for watchdog device tree bindings
Documentation: Add ebc-c384_wdt watchdog-parameters.txt entry
watchdog: shwdt: Use setup_timer()
watchdog: cpwd: Use setup_timer()
arm64: defconfig: enable Renesas Watchdog Timer
watchdog: renesas-wdt: add driver
watchdog: remove error message when unable to allocate watchdog device
watchdog: f71808e_wdt: Fix WDTMOUT_STS register read
watchdog: f71808e_wdt: Fix typo
watchdog: f71808e_wdt: Add F81865 support
watchdog: sp5100_tco: properly check for new register layouts
watchdog: core: Fix circular locking dependency
watchdog: core: fix trivial typo in a comment
watchdog: hpwdt: Adjust documentation to match latest kernel module parameters.
watchdog: imx2_wdt: add external reset support via dt prop
watchdog: octeon: Handle the FROZEN hot plug notifier actions.
watchdog: qcom: Report reboot reason
Here's the "big" driver core update for 4.7-rc1.
Mostly just debugfs changes, the long-known and messy races with removing
debugfs files should be fixed thanks to the great work of Nicolai Stange. We
also have some isa updates in here (the x86 maintainers told me to take it
through this tree), a new warning when we run out of dynamic char major
numbers, and a few other assorted changes, details in the shortlog.
All have been in linux-next for some time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0mwACgkQMUfUDdst+ynjXACgjNxR5nMUiM8ZuuD0i4Xj7VXd
hnIAoM08+XDCv41noGdAcKv+2WZVZWMC
=i+0H
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core update for 4.7-rc1.
Mostly just debugfs changes, the long-known and messy races with
removing debugfs files should be fixed thanks to the great work of
Nicolai Stange. We also have some isa updates in here (the x86
maintainers told me to take it through this tree), a new warning when
we run out of dynamic char major numbers, and a few other assorted
changes, details in the shortlog.
All have been in linux-next for some time with no reported issues"
* tag 'driver-core-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (32 commits)
Revert "base: dd: don't remove driver_data in -EPROBE_DEFER case"
gpio: ws16c48: Utilize the ISA bus driver
gpio: 104-idio-16: Utilize the ISA bus driver
gpio: 104-idi-48: Utilize the ISA bus driver
gpio: 104-dio-48e: Utilize the ISA bus driver
watchdog: ebc-c384_wdt: Utilize the ISA bus driver
iio: stx104: Utilize the module_isa_driver and max_num_isa_dev macros
iio: stx104: Add X86 dependency to STX104 Kconfig option
Documentation: Add ISA bus driver documentation
isa: Implement the max_num_isa_dev macro
isa: Implement the module_isa_driver macro
pnp: pnpbios: Add explicit X86_32 dependency to PNPBIOS
isa: Decouple X86_32 dependency from the ISA Kconfig option
driver-core: use 'dev' argument in dev_dbg_ratelimited stub
base: dd: don't remove driver_data in -EPROBE_DEFER case
kernfs: Move faulting copy_user operations outside of the mutex
devcoredump: add scatterlist support
debugfs: unproxify files created through debugfs_create_u32_array()
debugfs: unproxify files created through debugfs_create_blob()
debugfs: unproxify files created through debugfs_create_bool()
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.7. Here's the summary of
the changes:
- ATH79: Support for DTB passuing using the UHI boot protocol
- ATH79: Remove support for builtin DTB.
- ATH79: Add zboot debug serial support.
- ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
and DPT-Module.
- ATH79: Update devicetree clock support for AR9132 and AR9331.
- ATH79: Cleanup the DT code.
- ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
- ATH79: Fix regression in PCI window initialization.
- BCM47xx: Move SPROM driver to drivers/firmware/
- BCM63xx: Enable partition parser in defconfig.
- BMIPS: BMIPS5000 has I cache filing from D cache
- BMIPS: BMIPS: Add cpu-feature-overrides.h
- BMIPS: Add Whirlwind support
- BMIPS: Adjust mips-hpt-frequency for BCM7435
- BMIPS: Remove maxcpus from BCM97435SVMB DTS
- BMIPS: Add missing 7038 L1 register cells to BCM7435
- BMIPS: Various tweaks to initialization code.
- BMIPS: Enable partition parser in defconfig.
- BMIPS: Cache tweaks.
- BMIPS: Add UART, I2C and SATA devices to DT.
- BMIPS: Add BCM6358 and BCM63268support
- BMIPS: Add device tree example for BCM6358.
- BMIPS: Improve Improve BCM6328 and BCM6368 device trees
- Lantiq: Add support for device tree file from boot loader
- Lantiq: Allow build with no built-in DT.
- Loongson 3: Reserve 32MB for RS780E integrated GPU.
- Loongson 3: Fix build error after ld-version.sh modification
- Loongson 3: Move chipset ACPI code from drivers to arch.
- Loongson 3: Speedup irq processing.
- Loongson 3: Add basic Loongson 3A support.
- Loongson 3: Set cache flush handlers to nop.
- Loongson 3: Invalidate special TLBs when needed.
- Loongson 3: Fast TLB refill handler.
- MT7620: Fallback strategy for invalid syscfg0.
- Netlogic: Fix CP0_EBASE redefinition warnings
- Octeon: Initialization fixes
- Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
- Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
- Octeon: Correctly handle endian-swapped initramfs images.
- Octeon: Support CN73xx, CN75xx and CN78xx.
- Octeon: Remove dead code from cvmx-sysinfo.
- Octeon: Extend number of supported CPUs past 32.
- Octeon: Remove some code limiting NR_IRQS to 255.
- Octeon: Simplify octeon_irq_ciu_gpio_set_type.
- Octeon: Mark some functions __init in smp.c
- Octeon: Octeon: Add Octeon III CN7xxx interface detection
- PIC32: Add serial driver and bindings for it.
- PIC32: Add PIC32 deadman timer driver and bindings.
- PIC32: Add PIC32 clock timer driver and bindings.
- Pistachio: Determine SoC revision during boot
- Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
- Sibyte: Strip redundant comments from bcm1480_regs.h.
- Panic immediately if panic_on_oops is set.
- module: fix incorrect IS_ERR_VALUE macro usage.
- module: Make consistent use of pr_*
- Remove no longer needed work_on_cpu() call.
- Remove CONFIG_IPV6_PRIVACY from defconfigs.
- Fix registers of non-crashing CPUs in dumps.
- Handle MIPSisms in new vmcore_elf32_check_arch.
- Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
- Allow RIXI to be used on non-R2 or R6 cores.
- Reserve nosave data for hibernation
- Fix siginfo.h to use strict POSIX types.
- Don't unwind user mode with EVA.
- Fix watchpoint restoration
- Ptrace watchpoints for R6.
- Sync icache when it fills from dcache
- I6400 I-cache fills from dcache.
- Various MSA fixes.
- Cleanup MIPS_CPU_* definitions.
- Signal: Move generic copy_siginfo to signal.h
- Signal: Fix uapi include in exported asm/siginfo.h
- Timer fixes for sake of KVM.
- XPA TLB refill fixes.
- Treat perf counter feature
- Update John Crispin's email address
- Add PIC32 watchdog and bindings.
- Handle R10000 LL/SC bug in set_pte()
- cpufreq: Various fixes for Longson1.
- R6: Fix R2 emulation.
- mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
- ELF: ABI and FP fixes.
- Allow for relocatable kernel and use that to support KASLR.
- Fix CPC_BASE_ADDR mask
- Plenty fo smp-cps, CM, R6 and M6250 fixes.
- Make reset_control_ops const.
- Fix kernel command line handling of leading whitespace.
- Cleanups to cache handling.
- Add brcm, bcm6345-l1-intc device tree bindings.
- Use generic clkdev.h header
- Remove CLK_IS_ROOT usage.
- Misc small cleanups.
- CM: Fix compilation error when !MIPS_CM
- oprofile: Fix a preemption issue
- Detect DSP ASE v3 support:1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
MIPS: pic32mzda: fix getting timer clock rate.
MIPS: ath79: fix regression in PCI window initialization
MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
MIPS: Fix VZ probe gas errors with binutils <2.24
MIPS: perf: Fix I6400 event numbers
MIPS: DEC: Export `ioasic_ssr_lock' to modules
MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
MIPS: CM: Fix compilation error when !MIPS_CM
MIPS: Fix genvdso error on rebuild
USB: ohci-jz4740: Remove obsolete driver
MIPS: JZ4740: Probe OHCI platform device via DT
MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
MIPS: pistachio: Determine SoC revision during boot
MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
MIPS: Prevent "restoration" of MSA context in non-MSA kernels
MIPS: cevt-r4k: Dynamically calculate min_delta_ns
MIPS: malta-time: Take seconds into account
MIPS: malta-time: Start GIC count before syncing to RTC
MIPS: Force CPUs to lose FP context during mode switches
...
The function setup_timer combines the initialization of a timer with
the initialization of the timer's function and data fields.
The multiline code for timer initialization is now replaced
with function setup_timer.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The function setup_timer combines the initialization of a timer with
the initialization of the timer's function and data fields.
The multiline code for timer initialization is now replaced
with function setup_timer.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add support for watchdogs (RWDT and SWDT) found on RCar Gen3 based SoCs
from Renesas.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The dev_err message is superfluous because the failure is already
printed by dev_kzalloc, so remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Commits 190aa4304d (Add AMD Mullins platform support) and
cca118fa2a (Add AMD Carrizo platform support) enabled the
driver on a lot more devices, but the following commit missed
a single location in the code when checking if the SB800 register
offsets should be used. This leads to the wrong register being
written which in turn causes ACPI to go haywire.
Fix this by introducing a helper function to check for the new
register layout and use this consistently.
https://bugzilla.kernel.org/show_bug.cgi?id=114201https://bugzilla.redhat.com/show_bug.cgi?id=1329910
Fixes: bdecfcdb54 (sp5100_tco: fix the device check for SB800
and later chipsets)
Cc: stable@vger.kernel.org (4.5+)
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
lockdep reports the following circular locking dependency.
======================================================
INFO: possible circular locking dependency detected ]
4.6.0-rc3-00191-gfabf418 #162 Not tainted
-------------------------------------------------------
systemd/1 is trying to acquire lock:
((&(&wd_data->work)->work)){+.+...}, at: [<80141650>] flush_work+0x0/0x280
but task is already holding lock:
(&wd_data->lock){+.+...}, at: [<804acfa8>] watchdog_release+0x18/0x190
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&wd_data->lock){+.+...}:
[<80662310>] mutex_lock_nested+0x64/0x4a8
[<804aca4c>] watchdog_ping_work+0x18/0x4c
[<80143128>] process_one_work+0x1ac/0x500
[<801434b4>] worker_thread+0x38/0x554
[<80149510>] kthread+0xf4/0x108
[<80107c10>] ret_from_fork+0x14/0x24
-> #0 ((&(&wd_data->work)->work)){+.+...}:
[<8017c4e8>] lock_acquire+0x70/0x90
[<8014169c>] flush_work+0x4c/0x280
[<801440f8>] __cancel_work_timer+0x9c/0x1e0
[<804acfcc>] watchdog_release+0x3c/0x190
[<8022c5e8>] __fput+0x80/0x1c8
[<80147b28>] task_work_run+0x94/0xc8
[<8010b998>] do_work_pending+0x8c/0xb4
[<80107ba8>] slow_work_pending+0xc/0x20
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&wd_data->lock);
lock((&(&wd_data->work)->work));
lock(&wd_data->lock);
lock((&(&wd_data->work)->work));
*** DEADLOCK ***
1 lock held by systemd/1:
stack backtrace:
CPU: 2 PID: 1 Comm: systemd Not tainted 4.6.0-rc3-00191-gfabf418 #162
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[<8010f5e4>] (unwind_backtrace) from [<8010c038>] (show_stack+0x10/0x14)
[<8010c038>] (show_stack) from [<8039d7fc>] (dump_stack+0xa8/0xd4)
[<8039d7fc>] (dump_stack) from [<80177ee0>] (print_circular_bug+0x214/0x334)
[<80177ee0>] (print_circular_bug) from [<80179230>] (check_prevs_add+0x4dc/0x8e8)
[<80179230>] (check_prevs_add) from [<8017b3d8>] (__lock_acquire+0xc6c/0x14ec)
[<8017b3d8>] (__lock_acquire) from [<8017c4e8>] (lock_acquire+0x70/0x90)
[<8017c4e8>] (lock_acquire) from [<8014169c>] (flush_work+0x4c/0x280)
[<8014169c>] (flush_work) from [<801440f8>] (__cancel_work_timer+0x9c/0x1e0)
[<801440f8>] (__cancel_work_timer) from [<804acfcc>] (watchdog_release+0x3c/0x190)
[<804acfcc>] (watchdog_release) from [<8022c5e8>] (__fput+0x80/0x1c8)
[<8022c5e8>] (__fput) from [<80147b28>] (task_work_run+0x94/0xc8)
[<80147b28>] (task_work_run) from [<8010b998>] (do_work_pending+0x8c/0xb4)
[<8010b998>] (do_work_pending) from [<80107ba8>] (slow_work_pending+0xc/0x20)
Turns out the call to cancel_delayed_work_sync() in watchdog_release()
is not necessary and can be dropped. If the worker is no longer necessary,
the subsequent call to watchdog_update_worker() will cancel it. If it is
already running, it won't do anything, since the worker function checks
if it needs to ping the watchdog or not.
Reported-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Fixes: 11d7aba9ce ("watchdog: imx2: Convert to use infrastructure triggered keepalives")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
The IMX6 watchdog supports assertion of a signal (WDOG_B) which
can be pinmux'd to an external pin. This is typically used for boards that
have PMIC's in control of the IMX6 power rails. In fact, failure to use
such an external reset on boards with external PMIC's can result in various
hangs due to the IMX6 not being fully reset [1] as well as the board failing
to reset because its PMIC has not been reset to provide adequate voltage for
the CPU when coming out of reset at 800Mhz.
This uses a new device-tree property 'fsl,ext-reset-output' to indicate the
board has such a reset and to cause the watchdog to be configured to assert
WDOG_B instead of an internal reset both on a watchdog timeout and in
system_restart.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2015-March/333689.html
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Iain Paton <ipaton0@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
When performing a suspend operation, the kernel brings all of the
non-boot CPUs offline, calling the hot plug notifiers with the flag,
CPU_TASKS_FROZEN, set in the action code. Similarly, during resume,
the CPUs are brought back online, but again the notifiers have the
FROZEN flag set.
While some very few drivers really need to treat suspend/resume
specially, this driver unintentionally ignores the notifications.
This patch changes the driver to disable the watchdog interrupt
whenever the CPU goes offline, and to enable it whenever the CPU goes
back online. As a result, the suspended state is no longer a special
case that leaves the watchdog active.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Qualcom watchdog timer block reports if the system was reset by the
watchdog. Pass the information to user space.
Reviewed-by: Grant Grundler <grundler@chromium.org>
Tested-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Adds support for the deadman timer peripheral found on PIC32 class devices.
The primary function of the deadman timer (DMT) is to reset the processor
in the event of a software malfunction. The DMT is a free-running
instruction fetch timer, which is clocked whenever an instruction fetch
occurs until a count match occurs. Instructions are not fetched when
the processor is in sleep mode.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12703/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The WinSystems EBC-C384 watchdog timer is controlled via ISA bus
communication. As such, the ISA bus driver is more appropriate than the
platform driver for the WinSystems EBC-C384 watchdog timer driver.
Cc: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix spelling typos in printk from various part
of the codes.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 1717f2096b ("panic, x86: Fix re-entrance problem due to panic
on NMI") introduced nmi_panic() which prevents concurrent and recursive
execution of panic(). It also saves registers for the crash dump on x86
by later commit 58c5661f21 ("panic, x86: Allow CPUs to save registers
even if looping in NMI context").
hpwdt driver can call panic() from NMI handler, so replace it with
nmi_panic(). Also, do some cleanups.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Thomas Mingarelli <thomas.mingarelli@hpe.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull 'objtool' stack frame validation from Ingo Molnar:
"This tree adds a new kernel build-time object file validation feature
(ONFIG_STACK_VALIDATION=y): kernel stack frame correctness validation.
It was written by and is maintained by Josh Poimboeuf.
The motivation: there's a category of hard to find kernel bugs, most
of them in assembly code (but also occasionally in C code), that
degrades the quality of kernel stack dumps/backtraces. These bugs are
hard to detect at the source code level. Such bugs result in
incorrect/incomplete backtraces most of time - but can also in some
rare cases result in crashes or other undefined behavior.
The build time correctness checking is done via the new 'objtool'
user-space utility that was written for this purpose and which is
hosted in the kernel repository in tools/objtool/. The tool's (very
simple) UI and source code design is shaped after Git and perf and
shares quite a bit of infrastructure with tools/perf (which tooling
infrastructure sharing effort got merged via perf and is already
upstream). Objtool follows the well-known kernel coding style.
Objtool does not try to check .c or .S files, it instead analyzes the
resulting .o generated machine code from first principles: it decodes
the instruction stream and interprets it. (Right now objtool supports
the x86-64 architecture.)
From tools/objtool/Documentation/stack-validation.txt:
"The kernel CONFIG_STACK_VALIDATION option enables a host tool named
objtool which runs at compile time. It has a "check" subcommand
which analyzes every .o file and ensures the validity of its stack
metadata. It enforces a set of rules on asm code and C inline
assembly code so that stack traces can be reliable.
Currently it only checks frame pointer usage, but there are plans to
add CFI validation for C files and CFI generation for asm files.
For each function, it recursively follows all possible code paths
and validates the correct frame pointer state at each instruction.
It also follows code paths involving special sections, like
.altinstructions, __jump_table, and __ex_table, which can add
alternative execution paths to a given instruction (or set of
instructions). Similarly, it knows how to follow switch statements,
for which gcc sometimes uses jump tables."
When this new kernel option is enabled (it's disabled by default), the
tool, if it finds any suspicious assembly code pattern, outputs
warnings in compiler warning format:
warning: objtool: rtlwifi_rate_mapping()+0x2e7: frame pointer state mismatch
warning: objtool: cik_tiling_mode_table_init()+0x6ce: call without frame pointer save/setup
warning: objtool:__schedule()+0x3c0: duplicate frame pointer save
warning: objtool:__schedule()+0x3fd: sibling call from callable instruction with changed frame pointer
... so that scripts that pick up compiler warnings will notice them.
All known warnings triggered by the tool are fixed by the tree, most
of the commits in fact prepare the kernel to be warning-free. Most of
them are bugfixes or cleanups that stand on their own, but there are
also some annotations of 'special' stack frames for justified cases
such entries to JIT-ed code (BPF) or really special boot time code.
There are two other long-term motivations behind this tool as well:
- To improve the quality and reliability of kernel stack frames, so
that they can be used for optimized live patching.
- To create independent infrastructure to check the correctness of
CFI stack frames at build time. CFI debuginfo is notoriously
unreliable and we cannot use it in the kernel as-is without extra
checking done both on the kernel side and on the build side.
The quality of kernel stack frames matters to debuggability as well,
so IMO we can merge this without having to consider the live patching
or CFI debuginfo angle"
* 'core-objtool-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (52 commits)
objtool: Only print one warning per function
objtool: Add several performance improvements
tools: Copy hashtable.h into tools directory
objtool: Fix false positive warnings for functions with multiple switch statements
objtool: Rename some variables and functions
objtool: Remove superflous INIT_LIST_HEAD
objtool: Add helper macros for traversing instructions
objtool: Fix false positive warnings related to sibling calls
objtool: Compile with debugging symbols
objtool: Detect infinite recursion
objtool: Prevent infinite recursion in noreturn detection
objtool: Detect and warn if libelf is missing and don't break the build
tools: Support relative directory path for 'O='
objtool: Support CROSS_COMPILE
x86/asm/decoder: Use explicitly signed chars
objtool: Enable stack metadata validation on 64-bit x86
objtool: Add CONFIG_STACK_VALIDATION option
objtool: Add tool to perform compile-time stack metadata validation
x86/kprobes: Mark kretprobe_trampoline() stack frame as non-standard
sched: Always inline context_switch()
...
Pull watchdog updates from Wim Van Sebroeck:
- new drivers for: NI 903x/913x watchdog driver, WinSystems EBC-C384
watchdog timer and ARM SBSA watchdog driver
- Support for NCT6102D devices
- Improvements of the generic watchdog framework (improve restart
handler, make set_timeout optional, introduce infrastructure
triggered keepalives, ...
- improvements on the pnx4008 watchdog driver
- several smaller fixes and improvements
* git://www.linux-watchdog.org/linux-watchdog: (28 commits)
watchdog: Ensure that wdd is not dereferenced if NULL
watchdog: imx2: Convert to use infrastructure triggered keepalives
watchdog: dw_wdt: Convert to use watchdog infrastructure
watchdog: Add support for minimum time between heartbeats
watchdog: Make stop function optional
watchdog: Introduce WDOG_HW_RUNNING flag
watchdog: Introduce hardware maximum heartbeat in watchdog core
watchdog: Make set_timeout function optional
arm: lpc32xx: remove restart handler
arm: lpc32xx: phy3250 remove restart hook
watchdog: pnx4008: restart: support "cmd" from userspace
watchdog: pnx4008: add support for soft reset
watchdog: pnx4008: add restart handler
watchdog: pnx4008: update logging during power-on
watchdog: tangox_wdt: test clock rate to avoid division by 0
watchdog: atlas7_wdt: test clock rate to avoid division by 0
watchdog: s3c2410_wdt: Add max and min timeout values
Watchdog: introduce ARM SBSA watchdog driver
Documentation: add sbsa-gwdt driver documentation
watchdog: Add watchdog timer support for the WinSystems EBC-C384
...
Smatch rightfully complains that wdd is dereferenced in the watchdog
release function after being checked for NULL. Also make sure that it
is not accessed outside mutex protection to avoid use-after-free problems.
Fixes: e6c71e84e4c0 ("watchdog: Introduce WDOG_HW_RUNNING flag")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog infrastructure now supports handling watchdog keepalive
if the watchdog is running while the watchdog device is closed.
Convert the driver to use this infrastructure.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert driver to use watchdog infrastructure. This includes
infrastructure support to handle watchdog keepalive if the watchdog
is running while the watchdog device is closed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Some watchdogs require a minimum time between heartbeats.
Examples are the watchdogs in DA9062 and AT91SAM9x.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Not all hardware watchdogs can be stopped. The driver for
such watchdogs would typically only set the WATCHDOG_HW_RUNNING
flag in its stop function. Make the stop function optional and set
WATCHDOG_HW_RUNNING in the watchdog core if it is not provided.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WDOG_HW_RUNNING flag is expected to be set by watchdog drivers if
the hardware watchdog is running. If the flag is set, the watchdog
subsystem will ping the watchdog even if the watchdog device is closed.
The watchdog driver stop function is now optional and may be omitted
if the watchdog can not be stopped. If stopping the watchdog is not
possible but the driver implements a stop function, it is responsible
to set the WDOG_HW_RUNNING flag in its stop function.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Introduce an optional hardware maximum heartbeat in the watchdog core.
The hardware maximum heartbeat can be lower than the maximum timeout.
Drivers can set the maximum hardware heartbeat value in the watchdog data
structure. If the configured timeout exceeds the maximum hardware heartbeat,
the watchdog core enables a timer function to assist sending keepalive
requests to the watchdog driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
For some watchdogs, the watchdog driver handles timeout changes without
explicitly setting any registers. In this situation, the watchdog driver
might only set the 'timeout' variable but do nothing else.
This can as well be handled by the infrastructure, so make the set_timeout
callback optional. If WDIOF_SETTIMEOUT is configured but the .set_timeout
callback is not available, update the timeout variable in the
infrastructure code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Added support to verify if a "cmd" is passed from the userspace program rebooting the system;
- if a valid "cmd" is available, handle it;
- If the received "cmd" is not supported, use the default reboot mode.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add support for explicit soft reset using the reboot mode.
The default reboot mode behavior is unchanged;
you can overwrite the default reboot type in the board specific file
"DT_MACHINE_START" definition using the "reboot_mode" parameter.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add restart handler capability to the driver;
the restart handler implementation was taken from
"mach-lpc32xx" ("lpc23xx_restart" function).
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no need to add the driver name in the text to display
on the console during the power-on:
pnx4008-watchdog 4003c000.watchdog: PNX4008 Watchdog Timer: heartbeat 19 sec
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The clk API may return 0 on clk_get_rate, so we should check the result before
using it as a divisor. For this, refactor the code to use a central
error path.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The clk API may return 0 on clk_get_rate, so we should check the result before
using it as a divisor.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog maximum timeout value is determined by the number of bits
for the interval timer counter, its source clock frequency, the number
of bits of the prescaler and maximum divider value.
This can be calculated with the following equation:
max_timeout = counter / (freq / (max_prescale + 1) / max_divider)
Setting a maximum timeout value will allow the watchdog core to refuse
user-space calls to the WDIOC_SETTIMEOUT ioctl that sets not supported
timeout values.
For example, systemd tries to set a timeout of 10 minutes on reboot to
ensure that the machine will be rebooted even if a reboot failed. This
leads to the following error message on an Exynos5422 Odroid XU4 board:
[ 147.986045] s3c2410-wdt 101d0000.watchdog: timeout 600 too big
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
According to Server Base System Architecture (SBSA) specification,
the SBSA Generic Watchdog has two stage timeouts: the first signal (WS0)
is for alerting the system by interrupt, the second one (WS1) is a real
hardware reset.
More details about the hardware specification of this device:
ARM DEN0029B - Server Base System Architecture (SBSA)
This driver can operate ARM SBSA Generic Watchdog as a single stage watchdog
or a two stages watchdog, it's set up by the module parameter "action".
In the single stage mode, when the timeout is reached, your system
will be reset by WS1. The first signal (WS0) is ignored.
In the two stages mode, when the timeout is reached, the first signal (WS0)
will trigger panic. If the system is getting into trouble and cannot be reset
by panic or restart properly by the kdump kernel(if supported), then the
second stage (as long as the first stage) will be reached, system will be
reset by WS1. This function can help administrator to backup the system
context info by panic console output or kdump.
This driver bases on linux kernel watchdog framework, so it can get
timeout from module parameter and FDT at the driver init stage.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Graeme Gregory <graeme.gregory@linaro.org>
Tested-by: Pratyush Anand <panand@redhat.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull sparc fixes from David Miller:
1) System call tracing doesn't handle register contents properly across
the trace. From Mike Frysinger.
2) Hook up copy_file_range
3) Build fix for 32-bit with newer tools.
4) New sun4v watchdog driver, from Wim Coekaerts.
5) Set context system call has to allow for servicable faults when we
flush the register windows to memory
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix sparc64_set_context stack handling.
sparc32: Add -Wa,-Av8 to KBUILD_CFLAGS.
Add sun4v_wdt watchdog driver
sparc: Fix system call tracing register handling.
sparc: Hook up copy_file_range syscall.
The WinSystems EBC-C384 has an onboard watchdog timer. The timeout range
supported by the watchdog timer is 1 second to 255 minutes. Timeouts
under 256 seconds have a 1 second granularity, while the rest have a 1
minute granularity.
This driver adds watchdog timer support for this onboard watchdog timer.
The timeout may be configured via the timeout module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add support for the watchdog timer on NI cRIO-903x and cDAQ-913x real-
time controllers.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The 'action' (or restart mode) and data parameters may be used by restart
handlers, so they should be passed to the restart callback functions.
Cc: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Zodiac watchdog is implemented on a microcontoller. The reset reason
currently labelled "trigger" is not to detect when the watchdog has
triggered (as had been initially understood and suggested by the naming),
but to inform the reader that the watchdog, which in fact has it's own
hardware watchdog, has been reset because the hardware watchdog has
triggered. Renaming to "hw watchdog".
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Calling return copy_to_user(...) in an ioctl will not do the right thing
if there's a pagefault: copy_to_user returns the number of bytes not
copied in this case.
Fix up watchdog/rc32434_wdt to do
return copy_to_user(...)) ? -EFAULT : 0;
instead.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The BCM7038 watchdog driver is specific to Broadcom ARM and MIPS
SoCs so do not present it on other architectures, unless
build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The driver uses the atomic_io_modify() function to update registers, but
that function is only available on 32-bit ARM. Recent changes have added
ARCH_MVEBU support to 64-bit ARM and hence allowed this driver to build
on 64-bit ARM where this function isn't available and thereby causing
allmodconfig builds to break.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Technologic Systems TS-4800 is an i.MX515 board, so its drivers
are useless unless building a SOC_IMX51 kernel, except for build
testing purposes.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Damien Riegel <damien.riegel@savoirfairelinux.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
As used in (and tested on) the ASRock IMB-150 board. Implementation is
identical to other NCT chips, just with different registers.
Signed-off-by: Rob Kramer <rob@solution-space.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix the following build failure:
drivers/watchdog/hpwdt.c:359:5: error: expected ‘)’ before ‘FRAME_BEGIN’
which occurs because hpwdt.c relied on indirect inclusion to get asm/frame.h
definitions - but some (mostly randconfig) configs did not provide that.
Include <asm/frame.h> explicitly.
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Bernd Petrovitsch <bernd@petrovitsch.priv.at>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Cc: live-patching@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
asminline_call() is a callable non-leaf function which doesn't honor
CONFIG_FRAME_POINTER, which can result in bad stack traces.
Create a stack frame when CONFIG_FRAME_POINTER is enabled.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Bernd Petrovitsch <bernd@petrovitsch.priv.at>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/60de3cfb6f16d413bfb923036cc87fec132df735.1453405861.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For Intel SKL platform the ME device can inform the host via
asynchronous notification that the watchdog feature was activated
on the device. The activation doesn't require reboot.
In that case the driver registers the watchdog device with the kernel.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Intel Broadwell and newer platforms, the ME device can inform
the host whether the watchdog functionality is activated or not.
If the watchdog functionality is not activated then the watchdog interface
can be not registered and eliminate unnecessary pings and hence lower the
power consumption by avoiding waking up the device.
The feature can be deactivated also without reboot
in that case the watchdog device should be unregistered at runtime.
The information regarding the deactivation is reported
in the ping response command. In runtime case the unregistration
has to be run from a worker so that the ping initiated by the watchdog
core completes. Otherwise the flow will deadlock on watchdog
core mutex which both ping and unregistration acquire.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add entry for displaying current watchdog internal state
cat <debugfs>/mei_wdt/state
IDLE|START|RUNNING|STOPPING
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create a driver with the generic watchdog interface
for the MEI iAMT watchdog device.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver adds sparc hypervisor watchdog support. The default
timeout is 60 seconds and the range is between 1 and
31536000 seconds. Both watchdog-resolution and
watchdog-max-timeout MD properties settings are supported.
Signed-off-by: Wim Coekaerts <wim.coekaerts@oracle.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not every arch has io memory.
So, unbreak the build by fixing the dependencies.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The imgpdc_wdt driver can be built on all architectures with
CONFIG_COMPILE_TEST, but fails if no other watchdog driver is
enabled:
drivers/watchdog/built-in.o: In function `pdc_wdt_remove':
imgpdc_wdt.c:(.text+0x74): undefined reference to `watchdog_unregister_device'
This adds the normal 'select WATCHDOG_CORE' that is needed to
ensure the driver always builds cleanly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This change was requested by arm-soc maintainer Kevin Hilman
because the X in TANGOX is a wildcard.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In function ‘usb_pcwd_probe’:
drivers/watchdog/pcwd_usb.c:611:12: warning: variable ‘maxp’ set but not
used [-Wunused-but-set-variable]
int pipe, maxp;
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
sp805 wdt asserts interrupt for the first expiry and
reloads the counter. If wdt interrupt is set and count
reaches zero then wdt reset event is generated. To get
wdt reset at 't' timeout the driver loads wdt counter
with 't/2'. A ping before time 't' *should* prevent
wdt reset. Currently if ping is done after 't/2' then
wdt interrupt condition gets set. On the next countdown
of loadval wdt reset event occurs eventhough wdt was
reloaded before the set timeout 't'.
This patch clears the interrupt condition on ping.
Signed-off-by: Sandeep Tripathy <tripathy@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The header specifies GPL version 2 only, so make the MODULE_LICENSE
string use the respective string for that.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The probe and release functions in this driver are marked
as __init and __exit, but this is wrong as indicated by this
Kbuild error message:
WARNING: vmlinux.o(.data+0x1d2308): Section mismatch in reference from the variable asm9260_wdt_driver to the function .init.text:asm9260_wdt_probe()
This removes the annotations, to make the sysfs unbind attribute
and deferred probing work.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: aae03dc981 ("watchdog: add Alphascale asm9260-wdt driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The lifetime of the watchdog device pointer is different from the lifetime
of its character device. Remove it entirely to avoid race conditions.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog core now supports creating driver specific sysfs attributes
when creating the watchdog device.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Zodiac watchdog driver attaches additional sysfs attributes to the
watchdog device. This has a number of problems: The watchdog device
lifetime differs from the driver lifetime, and the device structure
should therefore not be accessed from drivers. Also, creating sysfs
attributes after driver registration results in a potential race condition
if user space expects the attributes to exist but they don't exist yet.
Add support for creating driver specific sysfs attributes to the watchdog
core to solve the problems.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Commit 8d2fa17151 ("watchdog: stmp3xxx: Stop the watchdog on system
halt") introduced the following build warning:
drivers/watchdog/stmp3xxx_rtc_wdt.c: In function 'wdt_notify_sys':
drivers/watchdog/stmp3xxx_rtc_wdt.c:78:29: warning: unused variable 'pdata' [-Wunused-variable]
Remove the unused 'pdata' and 'dev' variables.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for the watchdog core found on newer MediaTek Wifi
SoCs MT7621 and MT7628. There is no symbol for MT7628 as it is a subtype of
MT7620 so we depend on that instead.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reference counting is now implemented in the watchdog core and no longer
required in watchdog drivers.
Since it was implememented a no-op, and since the local memory is allocated
with devm_kzalloc(), the reference counting code in the driver really did
not really work anyway, and this patch effectively fixes a bug which could
cause a crash on unloading if the watchdog device was still open.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reference counting is now implemented in the watchdog core and no longer
required in watchdog drivers.
Since it was implememented a no-op, and since the local memory is allocated
with devm_kzalloc(), the reference counting code in the driver really did
not really work anyway, and this patch effectively fixes a bug which could
cause a crash on unloading if the watchdog device was still open.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
All variables required by the watchdog core to manage a watchdog are
currently stored in struct watchdog_device. The lifetime of those
variables is determined by the watchdog driver. However, the lifetime
of variables used by the watchdog core differs from the lifetime of
struct watchdog_device. To remedy this situation, watchdog drivers
can implement ref and unref callbacks, to be used by the watchdog
core to lock struct watchdog_device in memory.
While this solves the immediate problem, it depends on watchdog drivers
to actually implement the ref/unref callbacks. This is error prone,
often not implemented in the first place, or not implemented correctly.
To solve the problem without requiring driver support, split the variables
in struct watchdog_device into two data structures - one for variables
associated with the watchdog driver, one for variables associated with
the watchdog core. With this approach, the watchdog core can keep track
of its variable lifetime and no longer depends on ref/unref callbacks
in the driver. As a side effect, some of the variables originally in
struct watchdog_driver are now private to the watchdog core and no longer
visible in watchdog drivers.
As a side effect of the changes made, an ioctl will now always fail
with -ENODEV after a watchdog device was unregistered with the character
device still open. Previously, it would only fail with -ENODEV in some
situations. Also, ioctl operations are now atomic from driver perspective.
With this change, it is now guaranteed that the driver will not unregister
a watchdog between a timeout change and the subsequent ping.
The 'ref' and 'unref' callbacks in struct watchdog_driver are no longer
used and marked as deprecated.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A watchdog driver should not use watchdog subsystem internal flags.
Use a driver variable and flag instead to maintain the watchdog state
and to determine if a suspend operation is possible or not.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog character device is currently created in watchdog_dev.c,
and the watchdog device in watchdog_core.c. This results in
cross-dependencies, since device creation needs to know the watchdog
character device number as well as the watchdog class, both of which
reside in watchdog_dev.c.
Create the watchdog device in watchdog_dev.c to simplify the code.
Inspired by earlier patch set from Damien Riegel.
Cc: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The 'dev' pointer in struct watchdog_device is set by the watchdog core
when registering the watchdog device and not by the driver. It points to
the watchdog device, not its parent.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The device pointer in struct watchdog_device has a different lifetime
than the driver code and should not be used in drivers. Use the pointer
to the parent device instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The device pointer in struct watchdog_device has a different lifetime
than the driver code and should not be used in drivers. Use the pointer
to the parent device instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The device pointer in struct watchdog_device should not be used by drivers
and may be removed in the near future. Use the platform device pointer for
info messages instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Stopping a watchdog is a normal operation and does not warrant a log
message.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This adds support for the Sigma Designs SMP86xx/SMP87xx family built-in
watchdog.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds a driver for the Zodiac Aerospace RAVE Watchdog Procesor.
This device implements a watchdog timer, accessible over I2C.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add WD support for Alphascale asm9260 SoC. This driver
provide support for different function modes:
- HW mode to trigger SoC reset on timeout
- SW mode do soft reset if needed
- DEBUG mode
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This watchdog is instantiated in a FPGA that is memory mapped. It is
made of only one register, called the feed register. Writing to this
register will re-arm the watchdog for a given time (and enable it if it
was disable). It can be disabled by writing a special value into it.
It is part of a syscon block, and the watchdog register offset in this
block varies from board to board. This offset is passed in the syscon
property after the phandle to the syscon node.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds watchdog driver for CSRatlas7 platform.
On CSRatlas7, the 6th timer can act as a watchdog timer
when the Watchdog mode is enabled.
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: William Wang <William.Wang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add SoC specific data in the watchdog driver for the meson8b SoC.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
With this patch we refactor the driver code to enable watchdog support
for all platforms based on Amlogic meson SoCs.
The new default timeout is also now chosen considering the maximum
timeout allowed by the SoC.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch is for the rebranding changes for the corporate split at HP.
There are no functional changes with this patch.
Signed-off-by: Tom Mingarelli <thomas.mingarelli@hpe.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
With the early_enable module parameter the watchdog can be started
during driver probe time. If this is requested the bets are good that
the timer is already running, so to narrow the gap where the timer is
disabled only call the disable function when the timer shouldn't be
started.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
omap_wdt_start calls pm_runtime_get_sync so dropping a reference just
before calling omap_wdt_start doesn't make much sense. Moreover there is
no point to use the synchronous variant of pm_runtime_put because the
driver doesn't care if the clock is disabled before or after
omap_wdt_probe returns.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On 64bit platforms, "(1 << (16 + top)) / clk_get_rate(dw_wdt.clk)" is
sign-extended to 64bit then converted to unsigned 64bit, finally divide
the clk rate. If the top is the maximum TOP i.e 15, "(1 << (16 +15))"
will be sign-extended to 0xffffffff80000000, then converted to unsigned
0xffffffff80000000, which is a huge number, thus the final result is
wrong.
We fix this issue by giving usigned value(1U in this case) at first.
Let's assume clk rate is 25MHZ,
Before the patch:
dw_wdt_top_in_seconds(15) = -864612050
After the patch:
dw_wdt_top_in_seconds(15) = 85
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
the softdog has static variables which are accessed if its timer is
still running after the driver is unloaded. and lead to crash:
$modprobe softdog
$echo 1 >/dev/watchdog
$modprobe -r softdog
CPU 20 Unable to handle kernel paging request at virtual address
Oops[#1]:
CPU: 20 PID: 0 Comm: swapper/20 Not tainted 4.1.13-WR8.0.0.0_standard
...
Modules linked in: [last unloaded: softdog]
....
Call Trace:
[<ffffffff801e142c>] cascade+0x34/0xb0
[<ffffffff801e1964>] run_timer_softirq+0x30c/0x368
[<ffffffff80181044>] __do_softirq+0x1ec/0x418
[<ffffffff801815d0>] irq_exit+0x90/0x98
[<ffffffff8010749c>] plat_irq_dispatch+0xa4/0x140
[<ffffffff80152740>] ret_from_irq+0x0/0x4
[<ffffffff801529e0>] __r4k_wait+0x20/0x40
[<ffffffff801c2278>] cpu_startup_entry+0x2a0/0x368
[<ffffffff8015fa64>] start_secondary+0x444/0x4d8
add the module ref when timer is running to avoid to unload the softdog
module
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This allows the system to actually halt even if userspace forgot to
disable the watchdog first. Old behaviour was that the watchdog forced
the system to boot again.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
For SB800 and later chipsets, the register definitions are the same
with SB800. And for SB700 and older chipsets, the definitions should
be same with SP5100/SB7x0.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Denis Turischev <denis.turischev@compulab.co.il>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds following attributes to watchdog device's sysfs interface
to read its different status.
* state - reads whether device is active or not
* identity - reads Watchdog device's identity string.
* timeout - reads current timeout.
* timeleft - reads timeleft before watchdog generates a reset
* bootstatus - reads status of the watchdog device at boot
* status - reads watchdog device's internal status bits
* nowayout - reads whether nowayout feature was set or not
Testing with iTCO_wdt:
# cd /sys/class/watchdog/watchdog1/
# ls
bootstatus dev device identity nowayout power state
subsystem timeleft timeout uevent
# cat identity
iTCO_wdt
# cat timeout
30
# cat state
inactive
# echo > /dev/watchdog1
# cat timeleft
26
# cat state
active
# cat bootstatus
0
# cat nowayout
0
Signed-off-by: Pratyush Anand <panand@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
We need few sysfs attributes to know different status of a watchdog device.
To do that, we need to associate .dev_groups with watchdog_class. So
convert it from pointer to static.
Putting this static struct in watchdog_dev.c, so that static device
attributes defined in that file can be attached to it.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom reboot notifier block registration and use the one
provided by the watchdog core.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirlinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom reboot notifier block registration and use the one
provided by the watchdog core.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirlinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom reboot notifier block registration and use the one
provided by the watchdog core.
Note that this watchdog used to stop unconditionnaly on SYS_HALT and
SYS_POWER_OFF. The core function now calls ops->stop on SYS_HALT and
SYS_DOWN. To prevent the watchdog from being stopped on reboot, the
"always-running" property must be set, otherwise it will now be stopped.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirlinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom reboot notifier block registration and use the one
provided by the watchdog core.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirlinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom reboot notifier block registration and use the one
provided by the watchdog core.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirlinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Many watchdog drivers register a reboot notifier in order to stop the
watchdog on system reboot. Thus we can factorize this code in the
watchdog core.
For that purpose, a new notifier block is added in watchdog_device for
internal use only, as well as a new watchdog_stop_on_reboot helper
function.
If this helper is called, watchdog core registers the related notifier
block and will stop the watchdog when SYS_HALT or SYS_DOWN is received.
Since this operation can be critical on some platforms, abort the device
registration if the reboot notifier registration fails.
Suggested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom restart handler by using the one provided by the
watchdog core.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom restart handler by using the one provided by the
watchdog core.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom restart handler by using the one provided by the
watchdog core.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom restart handler by using the one provided by the
watchdog core.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom restart handler by using the one provided by the
watchdog core.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom restart handler by using the one provided by the
watchdog core.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom restart handler by using the one provided by the
watchdog core.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom restart handler by using the one provided by the
watchdog core.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom restart handler by using the one provided by the
watchdog core.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom restart handler by using the one provided by the
watchdog core.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom restart handler by using the one provided by the
watchdog core.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Get rid of the custom restart handler by using the one provided by the
watchdog core.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Many watchdog drivers implement the same code to register a restart
handler. This patch provides a generic way to set such a function.
The patch adds a new restart watchdog operation. If a restart priority
greater than 0 is needed, the driver can call
watchdog_set_restart_priority to set it.
Suggested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
WDT_MODE value need to be or-ed with MODE_KEY when setting
watchdog mode. Add it to mtk_wdt_stop function, so that the
watchdog can be stopped (e.g. during suspend).
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If we need to restart the watchdog due to someone changing the timeout
interval, stop the watchdog before restarting it. Otherwise, the new
timeout doesn't seem to take.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
"t" is controlled by the user. If "t" is a very large integer then it
could lead to a negative "tmrval". We cap the upper bound of "tmrval"
but, in the current code, we allow negatives. This is a bug and it
causes a static checker warning. Let's make "tmrval" unsigned to avoid
this problem.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Silences sparse warning:
drivers/watchdog/pnx4008_wdt.c:83:25:
warning: symbol 'wdt_clk' was not declared. Should it be static?
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If common clock framework is configured, the driver generates a warning,
which is fixed by this change:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Tainted: G W 4.3.0-rc2+ #171
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (pnx4008_wdt_probe+0x78/0x11c)
[<>] (pnx4008_wdt_probe) from [<>] (platform_drv_probe+0x50/0xa0)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
[<>] (__platform_driver_register) from [<>] (platform_wdt_driver_init+0x18/0x20)
[<>] (platform_wdt_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull watchdog update from Wim Van Sebroeck:
- New driver for Broadcom 7038 Set-Top Box
- imx2_wdt: Use register definition in regmap_write()
- intel-mid: add Magic Closure flag
- watchdog framework improvements:
- Use device tree alias for naming watchdogs
- propagate ping error code to the user space
- Always evaluate new timeout against min_timeout
- Use single variable name for struct watchdog_device
- include clean-ups
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: include: add units for timeout values in kerneldoc
watchdog: include: fix some typos
watchdog: core: propagate ping error code to the user space
watchdog: watchdog_dev: Use single variable name for struct watchdog_device
watchdog: Always evaluate new timeout against min_timeout
watchdog: intel-mid: add Magic Closure flag
watchdog: imx2_wdt: Use register definition in regmap_write()
watchdog: watchdog_dev: Use device tree alias for naming watchdogs
watchdog: Watchdog driver for Broadcom Set-Top Box
watchdog: bcm7038: add device tree binding documentation
Watchdog ping return errors are ignored by watchdog core,
Whatchdog daemon should be informed about possible hardware error or
underlaying device driver get unregistered.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The current code uses 'wdd', wddev', and 'watchdog' as variable names
for struct watchdog_device. This is confusing and makes it difficult
to enhance the code. Replace it all with 'wdd'.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Timo Kokkonen <timo.kokkonen@offcode.fi>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Adding WDIOF_MAGICCLOSE to Intel MID watchdog driver. Once the watchdog
is opened, it makes sense to disable watchdog only if it was gracefully
released.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In order to improve readability it is better to pass the register name
definition rather than to pass its hardcoded offset.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Currently there is no way to easily differentiate multiple
watchdog devices. The watchdogs are named by the order they
are probed.
1st probed watchdog: /dev/watchdog0
2nd probed watchdog: /dev/watchdog1
...
This change uses the alias of the watchdog device node for
the name of the watchdog.
aliases {
watchdog0 = "/...../...."
watchdog3 = "/..../....."
watchdog2 = "/..../....."
...
}
This will translate to...
/dev/watchdog0
/dev/watchdog3
/dev/watchdog2
v2
Assign alias number to id in watchdog_core instead of watchdog_dev.
If failed to get id, fallback to original ida_simple_get call.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Introduce /sys/debug/kernel/diag_stat with a statistic how many diagnose
calls have been done by each CPU in the system.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If I2C is built as module, the iTCO watchdog driver must be built as module
as well. I2C_I801 must only be selected if I2C is configured.
This fixes the following build errors, seen if I2C=m and ITCO_WDT=y.
i2c-i801.c:(.text+0x2bf055): undefined reference to `i2c_del_adapter'
i2c-i801.c:(.text+0x2c13e0): undefined reference to `i2c_add_adapter'
i2c-i801.c:(.text+0x2c17bd): undefined reference to `i2c_new_device'
Fixes: 2a7a0e9bf7 ("watchdog: iTCO_wdt: Add support for TCO on Intel Sunrisepoint")
Reviewed-by: Matt Fleming <matt.fleming@intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Currently poweroff/halt results in a reboot on the Raspberry Pi.
The firmware uses the RSTS register to know which partiton to
boot from. The partiton value is spread into bits
0, 2, 4, 6, 8, 10. Partiton 63 is a special partition used by
the firmware to indicate halt.
The firmware made this change in 19 Aug 2013 and was matched
by the downstream commit:
Changes for new NOOBS multi partition booting from gsh
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
These platform drivers have a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull watchdog updates from Wim Van Sebroeck:
- new driver for NXP LPC18xx Watchdog Timer
- new driver for SAMA5D4 watchdog timer
- add support for MCP79 to nv_tco driver
- clean-up and improvement of the mpc8xxx watchdog driver
- improvements to gpio-wdt
- at91sam9_wdt clock improvements
... and other small fixes and improvements
* git://www.linux-watchdog.org/linux-watchdog: (25 commits)
Watchdog: Fix parent of watchdog_devices
watchdog: at91rm9200: Correct check for syscon_node_to_regmap() errors
watchdog: at91sam9: get and use slow clock
Documentation: dt: binding: atmel-sama5d4-wdt: for SAMA5D4 watchdog driver
watchdog: add a driver to support SAMA5D4 watchdog timer
watchdog: mpc8xxx: allow to compile for MPC512x
watchdog: mpc8xxx: use better error code when watchdog cannot be enabled
watchdog: mpc8xxx: use dynamic memory for device specific data
watchdog: mpc8xxx: use devm_ioremap_resource to map memory
watchdog: mpc8xxx: make use of of_device_get_match_data
watchdog: mpc8xxx: simplify registration
watchdog: mpc8xxx: remove dead code
watchdog: lpc18xx_wdt_get_timeleft() can be static
DT: watchdog: Add NXP LPC18xx Watchdog Timer binding documentation
watchdog: NXP LPC18xx Watchdog Timer Driver
watchdog: gpio-wdt: ping already at startup for always running devices
watchdog: gpio-wdt: be more strict about hw_algo matching
Documentation: watchdog: at91sam9_wdt: add clocks property
watchdog: booke_wdt: Use infrastructure to check timeout limits
watchdog: (nv_tco) add support for MCP79
...
/sys/class/watchdog/watchdogn/device/modalias can help to identify the
driver/module for a given watchdog node. However, many wdt devices do not
set their parent and so, we do not see an entry for device in sysfs for
such devices.
This patch fixes parent of watchdog_device so that
/sys/class/watchdog/watchdogn/device is populated.
Exceptions: booke, diag288, octeon, softdog and w83627hf -- They do not
have any parent. Not sure, how we can identify driver for these devices.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
syscon_node_to_regmap() returns a regmap or an ERR_PTR().
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Commit dca1a4b5ff ("clk: at91: keep slow clk enabled to prevent system
hang") added a workaround for the slow clock as it is not properly handled
by its users.
Get and use the slow clock as it is necessary for the at91sam9 watchdog.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
From SAMA5D4, the watchdog timer is upgrated with a new feature,
which is describled as in the datasheet, "WDT_MR can be written
until a LOCKMR command is issued in WDT_CR".
That is to say, as long as the bootstrap and u-boot don't issue
a LOCKMR command, WDT_MR can be written more than once in the driver.
So the SAMA5D4 watchdog driver's implementation is different from
the at91sam9260 watchdog driver implemented in file at91sam9_wdt.c.
The user application open the device file to enable the watchdog timer
hardware, and close to disable it, and set the watchdog timer timeout
by seting WDV and WDD fields of WDT_MR register, and ping the watchdog
by issuing WDRSTT command to WDT_CR register with hard-coded key.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The MPC5125 processor features a watchdog device that is identical to
the MPC8610 one. So allow to enable the driver for MPC512x kernel
configurations.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
checkpatch warns about ENOSYS, telling "ENOSYS means 'invalid syscall
nr' and nothing else". So use ENODEV instead.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Instead of relying on global static memory dynamically allocate the
needed data. This has the benefit of some saved bytes if the driver is
not in use and making it possible to bind more than one device (even
though this has no known use case).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This function is new in v4.2-rc1 and makes a forward declaration of the
match table superfluous which can so be removed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Since commit ef90174f82 ("watchdog: watchdog_core: Add watchdog
registration deferral mechanism") there is no need to delay the call to
watchdog_register_device any more. So simplify the registration code
accordingly.
Resetting wd_base to NULL can the also be dropped because nothing
depends on it being NULL to signal probe failure any more. (The matching
wd_base = NULL in .remove was missing, too.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This commit adds support for the watchdog timer found in NXP LPC SoCs
family, which includes LPC18xx/LPC43xx. Other SoCs in that family may
share the same watchdog hardware.
Watchdog driver registers a restart handler that will restart the system
by performing an incorrect feed after ensuring the watchdog is enabled in
reset mode.
As watchdog cannot be disabled in hardware, driver's stop routine will
regularly send a keepalive ping using a timer.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
During probe for an always-running watchdog a timer is setup to
constantly ping the watchdog while the device is not open. The gpio to
ping the watchdog is setup to inactive.
For a watchdog with hw_algo = "toggle" this results in a ping depending
on the initial state of the gpio, for hw_algo = "level" no ping is
generated.
Make sure that the first automatic ping is sent immediately and not only
when the timer expires the first time. This makes the machine survive in
case more than half of the watchdog timeout is already elapsed. (Which
is very probable for the chip I'm faced with that has a timeout of one
second.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
strncmp(algo, "toggle", 6) doesn't compare the trailing '\0' byte, so
using
hw_algo = "toggleboggle"
is recognized the same way as
hw_algo = "toggle"
. While this doesn't introduce any problems for a device tree that
sticks to the documented settings it's still ugly.
Fix this by using strcmp to only match on "toggle" and "level".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog infrastructure checks the maximum timeout for us.
Use it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Tested on the Nvidia chipset with an SMBus controller PCI ID 0x0AA2
(as shown in the PCI listing during the boot sequence).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Commit f2147de334 ("watchdog: sunxi: support parameterized compatible
strings") introduced a regression in sunxi_wdt_start(), by which
the system reset function of the watchdog is not enabled upon
starting the watchdog. As a result, the system is not reset when the
watchdog expires. Fix it.
Fixes: f2147de334 ("watchdog: sunxi: support parameterized compatible strings")
Signed-off-by: Francesco Lavra <francescolavra.fl@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable@vger.kernel.org
Without .shutdown(), watchdog might reset the system during power off.
For example, if watchdog's timeout is set to 30s, then it is reset to
zero by mtk_wdt_ping(). During power off, no app will ping watchdog,
but watchdog is still running and may trigger reset.
Signed-off-by: Greta Zhang <greta.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
- Core Frameworks
- New Base API to traverse devices and their children in reverse order
- Bug Fixes
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
- Fix-ups
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2blS
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support:
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
Core Frameworks:
- New Base API to traverse devices and their children in reverse order
Bug Fixes:
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
Fix-ups:
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures"
* tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: jz4740-adc: Init mask cache in generic IRQ chip
mfd: cros_ec: spi: Add OF match table
mfd: stmpe: Add OF match table
mfd: max77686: Split out regulator part from the DT binding
mfd: Add DT binding for Maxim MAX77802 IC
mfd: max77686: Use a generic name for the PMIC node in the example
mfd: max77686: Don't suggest in binding to use a deprecated property
mfd: Add MFD_CROS_EC dependencies
mfd: cros_ec: Remove CROS_EC_PROTO dependency for SPI and I2C drivers
mfd: axp20x: Add a cell for the usb power_supply part of the axp20x PMICs
mfd: axp20x: Add missing registers, and mark more registers volatile
mfd: arizona: Fixup some formatting/white space errors
mfd: wm8994: Fix NULL pointer exception on missing pdata
of: Add vendor prefix for Nuvoton
mfd: mt6397: Implement wake handler and suspend/resume to handle wake up event
mfd: atmel-hlcdc: Add support for new SoCs
mfd: Export OF module alias information in missing drivers
mfd: stw481x: Export I2C module alias information
mfd: da9062: Support for the DA9063 OnKey in the DA9062 core
mfd: max899x: Avoid redundant irq_data lookup
...
The revision of the watchdog hardware in Sunrisepoint necessitates a new
"version" inside the TCO watchdog driver because some of the register
layouts have changed.
Also update the Kconfig entry to select both the LPC and SMBus drivers
since the TCO device is on the SMBus in Sunrisepoint.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Sunrisepoint (Skylake PCH) has the iTCO watchdog accessible across
the SMBus, unlike previous generations of PCH/ICH where it was on the
LPC bus. Because it's on the SMBus, it doesn't make sense to pass around
a 'struct lpc_ich_info', and leaking the type of bus into the iTCO
watchdog driver is kind of backwards anyway.
This change introduces a new 'struct itco_wdt_platform_data' for use
inside the iTCO watchdog driver and by the upcoming Intel Sunrisepoint
code, which neatly avoids having to include lpc_ich headers in the i801
i2c driver.
This change is overdue because lpc_ich_info has already found its way
into other TCO watchdog users, notably the intel_pmc_ipc driver where
the watchdog actually isn't on the LPC bus as far as I can see.
A simple translation layer is provided for converting from the existing
'struct lpc_ich_info' inside the lpc_ich mfd driver.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Acked-by: Darren Hart <dvhart@linux.intel.com> [drivers/x86 refactoring]
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With well over 200+ users of this api, there are a mere 12 users that
actually checked the return value of this function. And all of them
really didn't do anything with that information as the system or module
was shutting down no matter what.
So stop pretending like it matters, and just return void from
misc_deregister(). If something goes wrong in the call, you will get a
WARNING splat in the syslog so you know how to fix up your driver.
Other than that, there's nothing that can go wrong.
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Andreas Dilger <andreas.dilger@intel.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Christine Caulfield <ccaulfie@redhat.com>
Cc: David Teigland <teigland@redhat.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to my kernel.org alias instead of a badly named gmail address,
which I rarely use.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull watchdog updates from Wim Van Sebroeck:
"This contains:
- new driver for ST's LPC Watchdog
- new driver for Conexant Digicolor CX92755 SoC
- new driver for DA9062 watchdog
- Addition of the watchdog registration deferral mechanism
- several improvements on omap_wdt
- several improvements and reboot-support for imgpdc_wdt
- max63xx_wdt improvements
- imx2_wdt improvements
- dw_wdt improvements
- and other small improvements and fixes"
* git://www.linux-watchdog.org/linux-watchdog: (37 commits)
watchdog: omap_wdt: early_enable module parameter
watchdog: gpio_wdt: Add option for early registration
watchdog: watchdog_core: Add watchdog registration deferral mechanism
watchdog: max63xx: dynamically allocate device
watchdog: imx2_wdt: Disable previously acquired clock on error path
watchdog: imx2_wdt: Check for clk_prepare_enable() error
watchdog: hpwdt: Add support for WDIOC_SETOPTIONS
watchdog: docs: omap_wdt also understands nowayout
watchdog: omap_wdt: implement get_timeleft
watchdog: da9062: DA9062 watchdog driver
watchdog: imx2_wdt: set watchdog parent device
watchdog: mena21_wdt: Fix possible NULL pointer dereference
watchdog: dw_wdt: keepalive the watchdog at write time
watchdog: dw_wdt: No need for a spinlock
watchdog: imx2_wdt: also set wdog->timeout to new_timeout
watchdog: Allow compile test of GPIO consumers if !GPIOLIB
watchdog: cadence: Add dependency on HAS_IOMEM
watchdog: max63xx_wdt: Constify platform_device_id
watchdog: MAX63XX_WATCHDOG does not depend on ARM
watchdog: imgpdc: Add some documentation about the timeout
...
Add a early_enable module parameter to the omap_wdt that starts the
watchdog on module insertion. The default value is 0 which does not
start the watchdog - which also does not change the behavior if the
parameter is not given.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In some situation, mainly when it's not possible to disable a
watchdog, you may want the watchdog driver to be started as soon
as possible.
Adding GPIO_WATCHDOG_ARCH_INITCALL to raise initcall from
module_init to arch_initcall.
This patch require watchdog registration deferral mechanism
Signed-off-by: Jean-Baptiste Theou <jtheou@adeneo-embedded.us>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Currently, watchdog subsystem require the misc subsystem to
register a watchdog. This may not be the case in case of an
early registration of a watchdog, which can be required when
the watchdog cannot be disabled.
This patch introduces a deferral mechanism to remove this requirement.
Signed-off-by: Jean-Baptiste Theou <jtheou@adeneo-embedded.us>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch removes the static watchdog device for a new max63xx_wdt data
structure, and constifies the max63xx_timeout data.
The new structure contains pointers to pin access routines, which
abstracts mmap-specific code. This will ease future accesses like GPIO.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC
Conflicts:
arch/arm/mach-socfpga/core.h
Trivial remove/remove conflict with our cleanup branch.
Resolution: remove both sides
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZtPK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform support updates from Kevin Hilman:
"Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (134 commits)
ARM: zx: Add basic defconfig support for ZX296702
ARM: dts: zx: add an initial zx296702 dts and doc
clk: zx: add clock support to zx296702
dt-bindings: Add #defines for ZTE ZX296702 clocks
ARM: socfpga: fix build error due to secondary_startup
MAINTAINERS: ARM64: EXYNOS: Extend entry for ARM64 DTS
ARM: ep93xx: simone: support for SPI-based MMC/SD cards
MAINTAINERS: update Shawn's email to use kernel.org one
ARM: socfpga: support suspend to ram
ARM: socfpga: add CPU_METHOD_OF_DECLARE for Arria 10
ARM: socfpga: use CPU_METHOD_OF_DECLARE for socfpga_cyclone5
ARM: EXYNOS: register power domain driver from core_initcall
ARM: EXYNOS: use PS_HOLD based poweroff for all supported SoCs
ARM: SAMSUNG: Constify platform_device_id
ARM: EXYNOS: Constify irq_domain_ops
ARM: EXYNOS: add coupled cpuidle support for Exynos3250
ARM: EXYNOS: add exynos_get_boot_addr() helper
ARM: EXYNOS: add exynos_set_boot_addr() helper
ARM: EXYNOS: make exynos_core_restart() less verbose
ARM: EXYNOS: fix exynos_boot_secondary() return value on timeout
...
If watchdog_register_device() fails we should disable the previously
acquired wdev->clk clock on error path.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
WDIOC_SETOPTIONS makes it possible to disable and re-enable the
watchdog timer while the hpwdt driver is loaded.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The omap watchdog hardware is able to read the watchdog timer counter
register. This implements this functionality in the omap_wdt driver, so
one is can read the time until the watchdog will trigger the reset in
seconds using WDIOC_GETTIMELEFT.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add watchdog driver support for DA9062
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If on watchdog device registration a parent device is not set, then
the registered watchdog is considered to be a virtual device:
/sys/devices/virtual/watchdog/watchdog0
/sys/devices/virtual/watchdog/watchdog1
Setting a correct reference to a platform device allows to
distinguish multiple instances of iMX2+ hardware watchdogs:
/sys/devices/soc0/soc/2000000.aips-bus/20bc000.wdog/watchdog/watchdog0
/sys/devices/soc0/soc/2000000.aips-bus/20c0000.wdog/watchdog/watchdog1
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In a21_wdt_remove() we do a watchdog_unregister_device() on struct
a21_wdt_drv->wdt but never assign it.
Also move the dev_set_drvdata() call in front of the watchdog_register_device()
call, so it doesn't look like an error.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If you've got code that does this in a tight loop
1. Open watchdog
2. Send 'expect close'
3. Close watchdog
...you'll eventually trigger a watchdog reset. You can reproduce this
by using daisydog (1) and running:
while true; do daisydog -c > /dev/null; done
The problem is that each time you write to the watchdog for 'expect
close' it moves the timer .5 seconds out. The timer thus never fires
and never pats the watchdog for you.
1: http://git.chromium.org/gitweb/?p=chromiumos/third_party/daisydog.git
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Right now the dw_wdt uses a spinlock to protect dw_wdt_open(). The
problem is that while holding the spinlock we call:
-> dw_wdt_set_top()
-> dw_wdt_top_in_seconds()
-> clk_get_rate()
-> clk_prepare_lock()
-> mutex_lock()
Locking a mutex while holding a spinlock is not allowed and leads to
warnings like "BUG: spinlock wrong CPU on CPU#1", among other
problems.
There's no reason to use a spinlock. Only dw_wdt_open() was protected
and the test_and_set_bit() at the start of that function protects us
anyway.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Commit faad5de0b1 ("watchdog: imx2_wdt: convert to watchdog core api")
removes the custom ioctl function. The generic ioctl handler is not
setting the wdog->timeout to the new_timeout but handing this preset
value back to the userspace. This patch sets the new value in the
drivers set_timeout function to fix that problem.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Not all architectures have io memory.
Fixes:
drivers/built-in.o: In function `cdns_wdt_probe':
cadence_wdt.c:(.text+0x33b7c9): undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove the ARM Kconfig dependency since the Maxim MAX63xx devices are
architecture independent.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This watchdog hardware can be configured in terms of power-of-two
clock cycles. Therefore, the watchdog timeout configured by the user
will be rounded-up to the next possible hardware timeout.
This commit adds a comment explaining this.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Maximum timeout is currently set in clock cycles, but the watchdog
core expects it to be in seconds. Fix it.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Register a restart handler that will restart the system by writing
to the watchdog's SOFT_RESET register.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Set up the watchdog for the specified timeout before attempting to start it.
Signed-off-by: Naidu Tellapati <naidu.tellapati@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Since the heartbeat is statically initialized to its default value,
watchdog_init_timeout() will never look in the device-tree for a
timeout-sec value. Instead of statically initializing heartbeat,
fall back to the default timeout value if watchdog_init_timeout()
fails.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The omap watchdog has the annoying behaviour that writes to most
registers don't have any effect when the watchdog is already running.
Quoting the AM335x reference manual:
To modify the timer counter value (the WDT_WCRR register),
prescaler ratio (the WDT_WCLR[4:2] PTV bit field), delay
configuration value (the WDT_WDLY[31:0] DLY_VALUE bit field), or
the load value (the WDT_WLDR[31:0] TIMER_LOAD bit field), the
watchdog timer must be disabled by using the start/stop sequence
(the WDT_WSPR register).
Currently the timer is stopped in the .probe callback but still there
are possibilities that yield to a situation where omap_wdt_start is
entered with the timer running (e.g. when /dev/watchdog is closed
without stopping and then reopened). In such a case programming the
timeout silently fails!
To circumvent this stop the timer before reprogramming.
Assuming one of the first things the watchdog user does is setting the
timeout explicitly nothing too bad should happen because this explicit
setting works fine.
Fixes: 7768a13c25 ("[PATCH] OMAP: Add Watchdog driver support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Instead of using an over-long expression involving the ?: operator use
an if and instead of an else branch rely on the fact that the data
structure was allocated using devm_kzalloc. This also allows to put the
used helper variable into a more local scope.
There is no functional change.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This way only a single allocation is needed (per device). Also this
simplifies the data structure used by the driver because there is no
need anymore to link from one struct to the other (by means of
watchdog_{set,get}_drvdata).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Instead of (partly) open coding watchdog_init_timeout to determine the
inital timeout use the core function that exists for exactly this
purpose.
As a side effect the "timeout-sec" device-tree property is recognized now
(though currently unused in the omap device trees).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This commit add a driver for the watchdog functionality of the Conexant CX92755
SoC, from the Digicolor series of SoCs. Of 8 system timers provided by the
CX92755, the first one, timer A, can reset the chip when its counter reaches
zero. This driver uses this capability to provide userspace with a standard
watchdog, using the watchdog timer driver core framework. This driver also
implements a reboot handler for the reboot(2) system call.
The watchdog driver shares the timer registers with the CX92755 timer driver
(drivers/clocksource/timer-digicolor.c). The timer driver, however, uses only
timers other than A, so both drivers should coexist.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use endian agnostic IO functions for the watchdog driver for when it
is enabled on ATSAMA5D36 devices running in big endian.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Initial submission adding support for this IP only included Watchdog and
the Real-Time Clock. Now the third (and final) device is enabled this
trivial patch is required to update the comment in the Watchdog driver
to encompass Clocksource.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: David Paris <david.paris@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Since the WDT is what's used to drive restart and power off, it makes
more sense to keep it there, where the regs are already mapped and
definitions for them provided. Note that this means you may need to
add CONFIG_BCM2835_WDT to retain functionality of your kernel.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Driver updates for v4.1. Some of these are for drivers/soc, where we find more
and more SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
The larger parts of this branch are:
- MediaTek support for their PMIC wrapper interface, a high-level interface
for talking to the system PMIC over a dedicated I2C interface.
- Qualcomm SCM driver has been moved to drivers/firmware. It's used for CPU
up/down and needs to be in a shared location for arm/arm64 common code.
- Cleanup of ARM-CCI PMU code.
- Anoter set of cleanusp to the OMAP GPMC code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/sWo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for v4.1. Some of these are for drivers/soc, where we
find more and more SoC-specific drivers these days. Some are for
other driver subsystems where we have received acks from the
appropriate maintainers.
The larger parts of this branch are:
- MediaTek support for their PMIC wrapper interface, a high-level
interface for talking to the system PMIC over a dedicated I2C
interface.
- Qualcomm SCM driver has been moved to drivers/firmware. It's used
for CPU up/down and needs to be in a shared location for arm/arm64
common code.
- cleanup of ARM-CCI PMU code.
- another set of cleanusp to the OMAP GPMC code"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
soc/mediatek: Remove unused variables
clocksource: atmel-st: select MFD_SYSCON
soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs
arm-cci: Fix CCI PMU event validation
arm-cci: Split the code for PMU vs driver support
arm-cci: Get rid of secure transactions for PMU driver
arm-cci: Abstract the CCI400 PMU specific definitions
arm-cci: Rearrange code for splitting PMU vs driver code
drivers: cci: reject groups spanning multiple HW PMUs
ARM: at91: remove useless include
clocksource: atmel-st: remove mach/hardware dependency
clocksource: atmel-st: use syscon/regmap
ARM: at91: time: move the system timer driver to drivers/clocksource
ARM: at91: properly initialize timer
ARM: at91: at91rm9200: remove deprecated arm_pm_restart
watchdog: at91rm9200: implement restart handler
watchdog: at91rm9200: use the system timer syscon
mfd: syscon: Add atmel system timer registers definition
ARM: at91/dt: declare atmel,at91rm9200-st as a syscon
soc: qcom: gsbi: Add support for ADM CRCI muxing
...
My Pengutronix address is not valid anymore, redirect people to the Pengutronix
kernel team.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
My Pengutronix address is not valid anymore, redirect people to the Pengutronix
kernel team.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use fixed length string for register names. This saves 416 bytes
in text size.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix some trivial coding style issues to reduce noise from static analyzers.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert OCTEON watchdog to WATCHDOG_CORE API. This enables support
for multiple watchdogs on OCTEON boards.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove Kconfig dependency and enable driver for
all ARCHs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
MSM watchdog configuration happens in the same register block as the
timer, so we'll use the same binding as the existing timer.
The qcom-wdt will now be probed when devicetree has an entry compatible
with "qcom,kpss-timer" or "qcom-scss-timer".
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The seq_printf return value, because it's frequently misused,
will eventually be converted to void.
See: commit 1f33c41c03 ("seq_file: Rename seq_overflow() to
seq_has_overflowed() and make public")
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Guenter Roeck <linux~roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull s390 updates from Martin Schwidefsky:
"The major change in this merge is the removal of the support for
31-bit kernels. Naturally 31-bit user space will continue to work via
the compat layer.
And then some cleanup, some improvements and bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (23 commits)
s390/smp: wait until secondaries are active & online
s390/hibernate: fix save and restore of kernel text section
s390/cacheinfo: add missing facility check
s390/syscalls: simplify syscall_get_arch()
s390/irq: enforce correct irqclass_sub_desc array size
s390: remove "64" suffix from mem64.S and swsusp_asm64.S
s390/ipl: cleanup macro usage
s390/ipl: cleanup shutdown_action attributes
s390/ipl: cleanup bin attr usage
s390/uprobes: fix address space annotation
s390: add missing arch_release_task_struct() declaration
s390: make couple of functions and variables static
s390/maccess: improve s390_kernel_write()
s390/maccess: remove potentially broken probe_kernel_write()
s390/watchdog: support for KVM hypervisors and delete pr_info messages
s390/watchdog: enable KEEPALIVE for /dev/watchdog
s390/dasd: remove setting of scheduler from driver
s390/traps: panic() instead of die() on translation exception
s390: remove test_facility(2) (== z/Architecture mode active) checks
s390/cmpxchg: simplify cmpxchg_double
...
This series reworks some of the CCI-400 PMU code so that it can be used
on both ARM and ARM64-based systems, without the need to boot in secure
mode on the latter. This paves the way for CCI-500 support in future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVFWAiAAoJELescNyEwWM0pK8IALUinCT+Ec/Oi5WwGJaLgQgw
exlDFAcmml0xisxglGL7eHcvNBs/j4wFD37mqDUszrGW3jrM+Ex+/cvUzWIlEyZl
LjG99ZF2j51LFxDHMgpRwg1aD/NNQsQjwsuHHdCr+NHB5R2C0M4umsgX6Kt6/PE4
95LOnnjBOx4FkMOG9mZElzldUlqnhWd6drjQ9qZQar9VVVewfbR1LH/xQhjrCL0w
nwRzJwYj1LnLFO0hBVUAJSfvYltMF9PxBEx0FkyzN7QcuP1tLQ25NmGEvarHP6iZ
XpvTZ7akzButyUQbvz/kf6a0agPNUv1HHEqh7/Zddvgm//+p8nEBORuJ/cC6g1E=
=UHCi
-----END PGP SIGNATURE-----
Merge tag 'arm-perf-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into next/drivers
Merge "arm-cci PMU updates for 4.1" from Will Deacon:
CCI-400 PMU updates
This series reworks some of the CCI-400 PMU code so that it can be used
on both ARM and ARM64-based systems, without the need to boot in secure
mode on the latter. This paves the way for CCI-500 support in future.
* tag 'arm-perf-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux:
arm-cci: Fix CCI PMU event validation
arm-cci: Split the code for PMU vs driver support
arm-cci: Get rid of secure transactions for PMU driver
arm-cci: Abstract the CCI400 PMU specific definitions
arm-cci: Rearrange code for splitting PMU vs driver code
drivers: cci: reject groups spanning multiple HW PMUs
+ Linux 4.0-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
If the target sleep state of the system is not an ACPI sleep state
(S1, S2 or S3), the TCO watchdog needs to be stopped during system
suspend, because it may not be possible to ping it any more after
timekeeping has been suspended (suspend-to-idle does that for
one example).
For this reason, provide ->suspend_noirq and ->resume_noirq
callbacks for the iTCO watchdog driver and use them to stop
and restart the watchdog during system suspend and resume,
respectively, if the system is not going to enter an ACPI
sleep state (in which case the watchdog will be stopped
by the platform firmware before the state is entered).
Reported-and-tested-by: Borun Fu <borun.fu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
The IMG PDC watchdog driver heartbeat module parameter has no default so
it is initialised to zero. This results in the following warning during
probe:
imgpdc-wdt 2006000.wdt: Initial timeout out of range! setting max timeout
The module parameter description implies that the default value should
be PDC_WDT_DEF_TIMEOUT, which isn't yet used, so initialise it to that.
Also tweak the heartbeat module parameter description for consistency.
Fixes: 93937669e9 ("watchdog: ImgTec PDC Watchdog Timer Driver")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Naidu Tellapati <Naidu.Tellapati@imgtec.com>
Cc: Jude Abraham <Jude.Abraham@imgtec.com>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The IMG PDC watchdog probe function calls pdc_wdt_stop() prior to
watchdog_set_drvdata(), causing a NULL pointer dereference when
pdc_wdt_stop() retrieves the struct pdc_wdt_dev pointer using
watchdog_get_drvdata() and reads the register base address through it.
Fix by moving the watchdog_set_drvdata() call earlier, to where various
other pdc_wdt->wdt_dev fields are initialised.
Fixes: 93937669e9 ("watchdog: ImgTec PDC Watchdog Timer Driver")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Naidu Tellapati <Naidu.Tellapati@imgtec.com>
Cc: Jude Abraham <Jude.Abraham@imgtec.com>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
"ret" should be signed for the error handling to work correctly. This
doesn't matter much in real life since mtk_wdt_set_timeout() always
succeeds.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch extends the diag288 watchdog driver to be able to deal with KVM
hypervisors. Only z/VM needs special handling, we can use the same interface
as on LPAR. Remove all pr_info output to avoid misconception. Because there
is no value in these messages and only the pr_err messages make sense.
Signed-off-by: Xu Wang <gesaint@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There's no reason why we wouldn't want to be able to send a keep alive
message to /dev/watchdog (feed dog) for the s390 diag288 watchdog, so
let's enable the WDIOF_KEEPALIVEPING option.
Signed-off-by: Xu Wang <gesaint@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Restarting the at91rm9200 is done through programming the watchdog and waiting
for it to reset.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use a syscon regmap to access the system timer registers.
Also, rename the driver atmel_st_watchdog to stop conflicting with
at91sam9_wdt.c
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The watchdog interrupt (only used when activating software watchdog)
shouldn't be suspended when entering suspend mode, because it is shared
with a timer device (which request the line with IRQF_NO_SUSPEND) and once
the watchdog "Mode Register" has been written, it cannot be changed (which
means we cannot disable the watchdog interrupt when entering suspend).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
BCM5301X (ARCH_BCM_5301X) is a new Broadcom architecture using the same
SoC bus driver (bcma) as BCM47XX but based on ARM instead of MIPS.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add DT support to the jz4740 driver. Simple of_match_ptr. No other
modification for probe needed
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The dw_wdt_set_top() function takes in a value in seconds. In
dw_wdt_open() we were calling it with a value that's supposed to
represent the maximum value programmed into the "top" register with a
comment saying that we were trying to set the watchdog to its maximum
value. Instead we ended up setting the watchdog to ~15 seconds.
Let's fix this. However, setting things to the "max" gives me an 86
second watchdog in the system I'm looking at. 86 seconds feels a
little too long. We'll explicitly choose 30 seconds as a more
reasonable value.
NOTE: Ideally this driver should be transitioned to be a real watchdog
driver. Then we could use "watchdog_init_timeout" and let the timeout
be specified in a number of ways (device tree, module parameter, etc).
This patch should be considered a bit of a stopgap solution.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On some dw_wdt implementations the "top" register may be initted to 0
at bootup. In such a case, each "pat" of the watchdog will reset the
timer to 0xffff. That's pretty short.
The input clock of the wdt can be any of a wide range of values. On
an rk3288 system, I've seen the wdt clock be 24.75 MHz. That means
each tick is ~40ns and we'll count to 0xffff in ~2.6ms.
Because of the above two facts, it's a really good idea to pat the
watchdog after initting the "top" register properly and before
enabling the watchdog. If you don't then there's no way we'll get the
next heartbeat in time.
Jisheng Zhang fixed this problem on some dw_wdt versions by using the
TOP_INIT feature. However, the dw_wdt on rk3288 doesn't have TOP_INIT
so it's a good idea to also pat the watchdog manually.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog functionality in both chips is almost identical to NCT6779.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Just like in case of other watchdog drivers, use the new kernel core
API to provide restart support.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On some chips, like the TPS386000, the trigger cannot be disabled
and the CPU must keep toggling the line at all times. Add a switch
"always_running" to keep toggling the GPIO line regardless of the
state of the soft part of the watchdog. The "armed" member keeps
track of whether a timeout must also cause a reset.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Register a restart handler for the da9063 watchdog. System restart is
triggered by sending the shutdown command to the PMIC.
As more-suitable restart handlers may exist, the priority of the
watchdog restart handler is set to 128.
The actual restart method was inspired by a platform-specific patch from
the BSP by Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds a driver for the Mediatek SoC integrated
watchdog. This driver supports watchdog and software reset
for mt65xx and mt81xx SoCs.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This allows testing the watchdog easily with distros just by
doing pkill -9 watchdog.
Reported-by: Thomas Dziedzic <gostrc@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Replace device_reset() with devm_reset_control_get() + reset_control_deassert().
Make use of watchdog_init_timeout() instead of setting the timeout manually.
Signed-off-by: John Crispin <blogic@openwrt.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
allow_kdump was enabled as default since following commit.
commit a089361cf5,
watchdog: hpwdt: Unregister NMI events on exit.
But the initialization message was not modified.
So it still shows
HP Watchdog Timer Driver: NMI decoding initialized,
allow kernel dump: ON (default = 0/OFF) <=
This "default = 0/OFF" message may confuse users.
Fix it as "default = 1/ON".
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
IT8783 watchdog works as in IT872x
Tested on Adlink cPCI-6520 boards
Signed-off-by: Paolo Teti <paolo.teti@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make struct
watchdog_ops const as well.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Disable power down counter of the watchdog to avoid system resets. The
watchdog power down counter is set automatically by the chip. If it is
not set to 0 in the driver, the system resets.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Improve power management operations(suspend and resume) as part of
dev_pm_ops for IMX2 watchdog driver.
If PM will be supported, please make sure that the wdev->clk
could disable the watchdog's counter input clock source or can
mask watchdog's reset request to the core.
If watchdog is still used by consumers and resumes from deep
sleep state, we need to restart the watchdog again without
enabling the timer.
If watchdog been has started --> stopped by the consumers and
resumes from non-deep sleep state, then start the timer again.
If watchdog has been started --> stopped by the consumers and
resumes from deep sleep state, will do nothing. The watchdog
will be restarted by consumers next time to be used.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix the following build warning by passing the expected argument type to
watchdog_active():
drivers/watchdog/imx2_wdt.c: In function 'imx2_wdt_suspend':
drivers/watchdog/imx2_wdt.c:340:2: warning: passing argument 1 of 'watchdog_active' from incompatible pointer type [enabled by default]
In file included from drivers/watchdog/imx2_wdt.c:38:0:
include/linux/watchdog.h:104:20: note: expected 'struct watchdog_device *' but argument is of type 'struct watchdog_device **'
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add power management operations(suspend and resume) as part of
dev_pm_ops for IMX2 watchdog driver.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Pull timer core updates from Thomas Gleixner:
"The time(r) departement provides:
- more infrastructure work on the year 2038 issue
- a few fixes in the Armada SoC timers
- the usual pile of fixlets and improvements"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: armada-370-xp: Use the reference clock on A375 SoC
watchdog: orion: Use the reference clock on Armada 375 SoC
clocksource: armada-370-xp: Add missing clock enable
time: Fix sign bug in NTP mult overflow warning
time: Remove timekeeping_inject_sleeptime()
rtc: Update suspend/resume timing to use 64bit time
rtc/lib: Provide y2038 safe rtc_tm_to_time()/rtc_time_to_tm() replacement
time: Fixup comments to reflect usage of timespec64
time: Expose get_monotonic_coarse64() for in-kernel uses
time: Expose getrawmonotonic64 for in-kernel uses
time: Provide y2038 safe mktime() replacement
time: Provide y2038 safe timekeeping_inject_sleeptime() replacement
time: Provide y2038 safe do_settimeofday() replacement
time: Complete NTP adjustment threshold judging conditions
time: Avoid possible NTP adjustment mult overflow.
time: Rename udelay_test.c to test_udelay.c
clocksource: sirf: Remove hard-coded clock rate
On Atmel AT91, the conversion to device tree is now considered complete,
and all machines that were not already converted in 3.18 are assumed to
be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the platform
itself is not "multiplatform"-enabled, but both issues are going to be
taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size
of the branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iD8DBQBUhyNX5t5GS2LDRf4RAnjxAKCER7eoLNadu1/93n/a9d1nUz4MoQCcCZUq
BolxCOi0wr4YTcQtp7rHzWI=
=ykAB
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup on mach-at91 from Arnd Bergmann:
"On Atmel AT91, the conversion to device tree is now considered
complete, and all machines that were not already converted in 3.18 are
assumed to be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the
platform itself is not "multiplatform"-enabled, but both issues are
going to be taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size of
the branch"
* tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91: remove unused board.h file
ARM: at91: remove unneeded header files
ARM: at91/clocksource: remove !DT PIT initializations
ARM: at91: at91rm9200 ST initialization is now DT only
ARM: at91: remove old AT91-specific drivers
ARM: at91: cleanup initilisation code by removing dead code
ARM: at91/Kconfig: select board files automatically
ARM: at91: remove unused IRQ function declarations
ARM: at91: remove legacy IRQ driver and related code
ARM: at91: remove old at91-specific clock driver
ARM: at91: remove clock data in at91sam9n12.c and at91sam9x5.c files
ARM: at91: remove all !DT related configuration options
ARM: at91/trivial: update Kconfig comment to mention SAMA5
ARM: at91: always USE_OF from now on
ARM: at91/Kconfig: remove ARCH_AT91RM9200 option for drivers
ARM: at91: switch configuration option to SOC_AT91RM9200
ARM: at91: remove at91rm9200 legacy board support
ARM: at91: remove at91rm9200 legacy boards files
ARM: at91/Kconfig: remove useless fbdev Kconfig options
ARM: at91: remove at91sam9261/at91sam9g10 legacy board support
...
Daniel Lezcano muttered:
* Marvell timer updates from Ezequiel Garcia
- Add missing clock enable calls for armada
- Change source clock for clocksource and watchdog
* SIRF timer updates from Yanchang Li
- Make clock rate configurable
The precise selection is useless, so we simply remove these dependencies.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
The 25 MHz reference clock has better stability so its use is prefered over the
core clock. Change the Armada 375 clock initialization to use this reference
clock. To ensure the driver is compatible with an old devicetree, also provide
a fallback path which will silently return to the previous behavior.
While here, add the clock specification to the binding documentation.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This patch removes the magic value used for rebooting the board. This
value is useless and leads to a static checker warning as reported by
Dan Carpenter.
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
They need HAS_IOMEM, so let them depend on it, the related error (with
allmodconfig under um):
MODPOST 1205 modules
ERROR: "devm_ioremap_resource" [drivers/watchdog/tegra_wdt.ko] undefined!
ERROR: "devm_ioremap_resource" [drivers/watchdog/of_xilinx_wdt.ko] undefined!
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for the watchdog hardware found in A31 and
newer SoCs. This new hardware has registers at different offsets, and
the system reset control has been split out of the "mode" register
into a new "configuration" register.
Differences not supported by this driver include separate interrupt
lines for each watchdog, instead of sharing an interrupt line and
registers with the timer block.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for hardware parameters tied to compatible
strings, so similar hardware can reuse the driver.
This will be used to support the newer watchdog found in A31 and
later SoCs. Differences in the new hardware include separate
interrupt lines for each watchdog, and corresponding interrupt
control/status registers. Watchdog control registers were also
slightly rearranged.
Also replace ioread32()/iowrite32() with readl()/writel() in various
places changed.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Register the watchdog as the system restart function
to the new introducing kernel restart call chain in the
driver instead of providing the restart in machine desc.
This restart handler function is from the mxc_restart()
in arch/arm/mach-imx/system.c
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WDT's BITE_TIME warm-reset behavior can be leveraged as a last
resort mechanism for triggering chip reset. Usually, other restart
methods (such as PS_HOLD) are preferrable for issuing a more complete
reset of the chip. As such, keep the priority of the watchdog notifier
low.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On a lot of Samsung systems the watchdog is responsible for restarting the
system and until now this code was contained in plat-samsung/watchdog-reset.c.
With the introduction of the restart handlers, this code can now move into
driver itself, removing the need for arch-specific code.
Tested on a S3C2442 based GTA02
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kernel core now provides an API to trigger a system restart.
Register with it to support restarting the system via. watchdog.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the watchdog driver for the Amlogic Meson SoCs used also
to reboot the device.
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no conflict with rtc/rtc-stmp3xxx.c parent
because modified registers in PM functions of stmp3xxx_rtc_wdt
are different.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This driver supports the watchdog device inside the DA9063 PMIC.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This adds a driver for the watchdog timer available in Ricoh RN5T618
PMIC. The device supports a programmable expiration time of 1, 8, 32
or 128 seconds.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Exynos7 SoC has a Watchdog for Atlas (A57) cores
This patch adds support for the Atlas watchdog.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a driver for the watchdog timer block found in the Krait Processor
Subsystem (KPSS) on the MSM8960, APQ8064, and IPQ8064.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The TOP_INIT, ie bit 4-7 of the WDOG_TIMEOUT_RANGE_REG_OFFSET register
may be zero, so the timeout period may be very short after initialization
is done, thus the system may be reset soon after enabling. We fix this
problem by also initialising the TOP_INIT when setting TOP in function
dw_wdt_set_top().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add Cadence WDT driver. This is used by Xilinx Zynq.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no need to store the return value of misc_deregister() in a
variable. Instead we can just return the value directly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Building booke_wdt fails when trying to build as a module as there is no
early_param() in module. Fix by using module_param() instead of early_param().
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
Register ntc_thermistor driver with thermal subsystem.
Add support for F15h M60h to k10temp driver.
Add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vI5p
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for menf21bmc.
- convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
- register ntc_thermistor driver with thermal subsystem.
- add support for F15h M60h to k10temp driver.
- add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18
* tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ab8500) Call kernel_power_off instead of pm_power_off
hwmon: (menf21bmc) Introduce MEN14F021P00 BMC HWMON driver
leds: leds-menf21bmc: Introduce MEN 14F021P00 BMC LED driver
watchdog: menf21bmc_wdt: Introduce MEN 14F021P00 BMC Watchdog driver
mfd: menf21bmc: Introduce MEN 14F021P00 BMC MFD Core driver
hwmon: (ntc_thermistor) Add ntc thermistor to thermal subsystem as a sensor.
hwmon: (smsc47b397) Convert to devm_hwmon_device_register_with_groups
MAINTAINERS: add entry for the PWM fan driver
hwmon: (k10temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (k10temp) Add support for F15h M60h
hwmon: (da9052) Convert to devm_hwmon_device_register_with_groups
hwmon: (da9055) Convert to devm_hwmon_device_register_with_groups
hwmon: (ads1015) Use of_property_read_u32 at appropriate places
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cP1w
-----END PGP SIGNATURE-----
Merge tag 'restart-handler-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull restart handler infrastructure from Guenter Roeck:
"This series was supposed to be pulled through various trees using it,
and I did not plan to send a separate pull request. As it turns out,
the pinctrl tree did not merge with it, is now upstream, and uses it,
meaning there are now build failures.
Please pull this series directly to fix those build failures"
* tag 'restart-handler-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
arm/arm64: unexport restart handlers
watchdog: sunxi: register restart handler with kernel restart handler
watchdog: alim7101: register restart handler with kernel restart handler
watchdog: moxart: register restart handler with kernel restart handler
arm: support restart through restart handler call chain
arm64: support restart through restart handler call chain
power/restart: call machine_restart instead of arm_pm_restart
kernel: add support for kernel restart handler call chain
The kernel core now provides an API to trigger a system restart. Register
with it instead of setting arm_pm_restart.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kernel core now provides an API to trigger a system restart. Register
with it to restart the system instead of misusing the reboot notifier.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kernel now provides an API to trigger a system restart. Register with
it instead of setting arm_pm_restart.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Added driver to support the 14F021P00 BMC Watchdog.
The BMC is a Board Management Controller including watchdog functionality.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 3.17. It contains:
- misc Cavium Octeon, BCM47xx, BCM63xx and Alchemy updates
- MIPS ptrace updates and cleanups
- various fixes that will also go to -stable
- a number of cleanups and small non-critical fixes.
- NUMA support for the Loongson 3.
- more support for MSA
- support for MAAR
- various FP enhancements and fixes"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
MIPS: jz4740: remove unnecessary null test before debugfs_remove
MIPS: Octeon: remove unnecessary null test before debugfs_remove_recursive
MIPS: ZBOOT: implement stack protector in compressed boot phase
MIPS: mipsreg: remove duplicate MIPS_CONF4_FTLBSETS_SHIFT
MIPS: Bonito64: remove a duplicate define
MIPS: Malta: initialise MAARs
MIPS: Initialise MAARs
MIPS: detect presence of MAARs
MIPS: define MAAR register accessors & bits
MIPS: mark MSA experimental
MIPS: Don't build MSA support unless it can be used
MIPS: consistently clear MSA flags when starting & copying threads
MIPS: 16 byte align MSA vector context
MIPS: disable preemption whilst initialising MSA
MIPS: ensure MSA gets disabled during boot
MIPS: fix read_msa_* & write_msa_* functions on non-MSA toolchains
MIPS: fix MSA context for tasks which don't use FP first
MIPS: init upper 64b of vector registers when MSA is first used
MIPS: save/disable MSA in lose_fpu
MIPS: preserve scalar FP CSR when switching vector context
...
Pull s390 updates from Martin Schwidefsky:
"Mostly cleanups and bug-fixes, with two exceptions.
The first is lazy flushing of I/O-TLBs for PCI to improve performance,
the second is software dirty bits in the pmd for the madvise-free
implementation"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (24 commits)
s390/locking: Reenable optimistic spinning
s390/mm: implement dirty bits for large segment table entries
KVM: s390/mm: Fix page table locking vs. split pmd lock
s390/dasd: fix camel case
s390/3215: fix hanging console issue
s390/irq: improve displayed interrupt order in /proc/interrupts
s390/seccomp: fix error return for filtered system calls
s390/pci: introduce lazy IOTLB flushing for DMA unmap
dasd: fix error recovery for alias devices during format
dasd: fix list_del corruption during format
dasd: fix unresponsive device during format
dasd: use aliases for formatted devices during format
s390/pci: fix kmsg component
s390/kdump: Return NOTIFY_OK for all actions other than MEM_GOING_OFFLINE
s390/watchdog: Fix module name in Kconfig help text
s390/dasd: replace seq_printf by seq_puts
s390/dasd: replace pr_warning by pr_warn
s390/dasd: Move EXPORT_SYMBOL after function/variable
s390/dasd: remove unnecessary null test before debugfs_remove
s390/zfcp: use qdio buffer helpers
...
Most of the watchdog code is duplicated between the machine restart code and
the watchdog driver. Add the restart hook to the watchdog driver, to be able to
remove it from the machine code eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This watchdog driver will be working on IMX2+, Vybrid, LS1, LS2+
platforms, and will be in different endianness mode in those SoCs:
SoCs WDT endian mode
------------------------------------
IMX2+ LE
Vybird LE
LS1 BE
LS2 LE
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
devm_ioremap_resource check for a valid resource. Remove the unnecessary check.
Also group platform_get_resource and devm_ioremap_resource together for better
readability.
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
devm_ioremap_resource() checks for valid resource.
Remove the un-necessary check after platform_get_resource().
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
devm_ioremap_resource() checks for valid resource.
Remove the un-necessary check after platform_get_resource().
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If CONFIG_HOTPLUG_CPU is set, the driver thinks bootloader entry
address is configured and we should jump there. However, this is
not necessarily true if the kernel is booted on a system
with older/incompatible bootloader.
Add dynamic checks for the bootloader entry address.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-watchdog@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7201/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The help text for DIAG288_WATCHDOG in drivers/watchdog/Kconfig
still mentioned the misleading old module name vmwatchdog.
This patch changes that to the correct new name diag288_wdt.
Signed-off-by: Philipp Hachtmann <phacht@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull s390 patches from Martin Schwidefsky:
"A couple of bug fixes, a debug change for qdio, an update for the
default config, and one small extension.
The watchdog module based on diagnose 0x288 is converted to the
watchdog API and it now works under LPAR as well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ccwgroup: use ccwgroup_ungroup wrapper
s390/ccwgroup: fix an uninitialized return code
s390/ccwgroup: obtain extra reference for asynchronous processing
qdio: Keep device-specific dbf entries
s390/compat: correct ucontext layout for high gprs
s390/cio: set device name as early as possible
s390: update default configuration
s390: avoid format strings leaking into names
s390/airq: silence lockdep warning
s390/watchdog: add support for LPAR operation (diag288)
s390/watchdog: use watchdog API
s390/sclp_vt220: Enable ASCII console per default
s390/qdio: replace shift loop by ilog2
s390/cio: silence lockdep warning
s390/uaccess: always load the kernel ASCE after task switch
s390/ap_bus: Make modules parameters visible in sysfs
Add initial Intel MID watchdog driver support.
This driver is an initial implementation of generic Intel MID watchdog
driver. Currently it supports Intel Merrifield platform.
Signed-off-by: Eric Ernst <eric.ernst@intel.com>
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Implementation of ->set_timeout() is supposed to set 'timeout' field of 'struct
watchdog_device' passed to it. sp805 was rather setting this in a local
variable. Fix it.
Reported-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: <stable@vger.kernel.org> # 2.6.36+
Basically, this patch does the following:
1. Move the codes of parsing boot parameters from setup-common.c
to driver. In this way, code reader can know directly that
there are boot parameters that can change the timeout.
2. Make boot parameter 'booke_wdt_period' effective.
currently, when driver is loaded, default timeout is always
being used in stead of booke_wdt_period.
3. Wrap up the watchdog timeout in device struct and clean up
unnecessary codes.
Signed-off-by: Tang Yuantian <yuantian.tang@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Li Yang <leoli@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
All three iop variants we support in Linux (iop32x, iop33x and
iop13xx) seem to have support for the watchdog hardware, but this
driver fails to build for the first two of these because it
uses the IOP13XX_WDTCR_IB_RESET macro that is only defined for
iop13xx.
This clarifies the dependency in Kconfig to avoid randconfig
build errors. It is unlikely that anyone will ever miss support
for this driver on the ancient iop3xx platforms, so we don't
need to bother trying to fix it properly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Since both chips are now supported by the w83627hf watchdog driver,
the chip specific drivers are no longer needed and can be removed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add early_disable module parameter to match functionality previously
available in the w83697hf_wdt driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This commit adds support for the Armada 375 and Armada 380 SoCs.
This SoC variant has a second RSTOUT register, in addition to the already
existent, which is shared with the system-controller. To handle this RSTOUT,
we introduce a new MMIO register 'rstout_mask' to be required on
'armada-{375,380}-watchdog' new compatible string.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In order to support other SoCs, it's needed to have a different enabled()
implementation for each SoC. This commit adds no functionality, and it
consists of preparation work.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In order to support other SoCs, it's needed to have a different stop()
implementation for each SoC. This commit adds no functionality, and it
consists of preparation work.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The RSTOUT register on the Armada 370 SoC variant is a dedicated register
(not shared across orthogonal subsystems) and so it's not needed to write
it atomically.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Separate the RSTOUT register mapping for the different compatible strings
supported by the driver. This allows to use devm_ioremap on SoC variants that
share the RSTOUT register, and devm_ioremap_resource (which requests the MMIO
region) on SoCs that have a dedicated RSTOUT register.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
