Add a INTC_PINT() macro with various helper bits to allow SoCs
like sh73a0 to suppor the PINT hardware using regular INTC tables.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Implement GPIO hotplugging via TMIO_MMC_HAS_COLD_CD for
AG5EVM SDHI0. This is possible now when INTCA is used for
IRQ triggering on sh73a0. Without INTCA IRQ support we are
left with the GIC hardware block that does not support
dealing with active low interrupt sources.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve IRQ triggering support by making use of the macro
INTC_IRQ_PINS_32() for INTCA on sh73a0. Unfortunately it
is not as easy as just using the macro as-is, we need to
do mask and unmaks in the GIC but configure other bits
and ack in INTCA. Update GPIO IRQ mappings while at it.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for sh73a0 GPIO IRQs by making use
of the PFC GPIO IRQ feature. Only IRQ pins are supported
at this time. In the future when PINT interrupts also are
supported properly we can easily extend the table with such
information. Also, the sh73a0 is currently making use of
the GIC for external interrupt which is rather unflexible
when it comes to triggering configuration at this point.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Always use CS0 shadow area for NOR flash instead of regular CS0
memory area on ap4evb.
When booting from CS0 NOR Flash the regular CS0 memory area is
available, but when booting via USB the MASK ROM gets mapped to
0x0 which gets in the way for the NOR Flash. Always using CS0
shadow area works well for both NOR Flash boot and USB boot.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Always use CS0 shadow area for NOR flash instead of regular CS0
memory area on Mackerel.
When booting from CS0 NOR Flash the regular CS0 memory area is
available, but when booting via USB the MASK ROM gets mapped to
0x0 which gets in the way for the NOR Flash. Always using CS0
shadow area works well for both NOR Flash boot and USB boot.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add INTC_IRQ_PINS_16() and INTC_IRQ_PINS_32() to mach/intc.h.
These macros define 16 or 32 external IRQ pins on a certain
memory base address. Can be used with INTCA or INTCS.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (144 commits)
[media] saa7134.h: Suppress compiler warnings when CONFIG_VIDEO_SAA7134_RC is not set
[media] it913x [VER 1.07] Support for single ITE 9135 devices
[media] Support for Terratec G1
[media] cx25821: off by one in cx25821_vidioc_s_input()
[media] media: tea5764: reconcile Kconfig symbol and macro
[media] omap_vout: Add poll() support
[media] omap3isp: preview: Add crop support on the sink pad
[media] omap3isp: preview: Rename min/max input/output sizes defines
[media] omap3isp: preview: Remove horizontal averager support
[media] omap3isp: Report the ISP revision through the media controller API
[media] omap3isp: ccdc: remove redundant operation
[media] omap3isp: Fix memory leaks in initialization error paths
[media] omap3isp: Add missing mutex_destroy() calls
[media] omap3isp: Move *_init_entities() functions to the init/cleanup section
[media] omap3isp: Move media_entity_cleanup() from unregister() to cleanup()
[media] MFC: Change MFC firmware binary name
[media] vb2: add vb2_get_unmapped_area in vb2 core
[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor
[media] v4l: Add AUTO option for the V4L2_CID_POWER_LINE_FREQUENCY control
[media] media: ov6650: stylistic improvements
...
The sh_mobile_ceu_camera driver has been converted to use the V4L2
subdevice .[gs]_mbus_config() operations, therefore we don't need
SOCAM_* flags for the soc_camera_platform driver anymore. Remove
them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Camera-switching GPIOs are provided by a i2c GPIO extender, switching
them can send the caller to sleep. Use the GPIO API *_cansleep methods
explicitly to avoid runtime warnings.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prepare the board to switch to the new subdevice media-bus configuration
operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sh_mobile_csi2 driver will change meaning of the .lanes platform
data field from "bitmask of used lanes" to "number of used lanes."
To avoid a regression during this transition switch ap4evb to rely
on the 2 lane default.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-next' of git://git.infradead.org/users/sameo/mfd-2.6: (80 commits)
mfd: Fix missing abx500 header file updates
mfd: Add missing <linux/io.h> include to intel_msic
x86, mrst: add platform support for MSIC MFD driver
mfd: Expose TurnOnStatus in ab8500 sysfs
mfd: Remove support for early drop ab8500 chip
mfd: Add support for ab8500 v3.3
mfd: Add ab8500 interrupt disable hook
mfd: Convert db8500-prcmu panic() into pr_crit()
mfd: Refactor db8500-prcmu request_clock() function
mfd: Rename db8500-prcmu init function
mfd: Fix db5500-prcmu defines
mfd: db8500-prcmu voltage domain consumers additions
mfd: db8500-prcmu reset code retrieval
mfd: db8500-prcmu tweak for modem wakeup
mfd: Add db8500-pcmu watchdog accessor functions for watchdog
mfd: hwacc power state db8500-prcmu accessor
mfd: Add db8500-prcmu accessors for PLL and SGA clock
mfd: Move to the new db500 PRCMU API
mfd: Create a common interface for dbx500 PRCMU drivers
mfd: Initialize DB8500 PRCMU regs
...
Fix up trivial conflicts in
arch/arm/mach-imx/mach-mx31moboard.c
arch/arm/mach-omap2/board-omap3beagle.c
arch/arm/mach-u300/include/mach/irqs.h
drivers/mfd/wm831x-spi.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock:
hwspinlock: add MAINTAINERS entries
hwspinlock/omap: omap_hwspinlock_remove should be __devexit
hwspinlock/u8500: add hwspinlock driver
hwspinlock/core: register a bank of hwspinlocks in a single API call
hwspinlock/core: remove stubs for register/unregister
hwspinlock/core: use a mutex to protect the radix tree
hwspinlock/core/omap: fix id issues on multiple hwspinlock devices
hwspinlock/omap: simplify allocation scheme
hwspinlock/core: simplify 'owner' handling
hwspinlock/core: simplify Kconfig
Fix up trivial conflicts (addition of omap_hwspinlock_pdata, removal of
omap_spinlock_latency) in arch/arm/mach-omap2/hwspinlock.c
Also, do an "evil merge" to fix a compile error in omap_hsmmc.c which
for some reason was reported in the same email thread as the "please
pull hwspinlock changes".
* 'next/soc' of git://git.linaro.org/people/arnd/arm-soc: (21 commits)
MAINTAINERS: add ARM/FREESCALE IMX6 entry
arm/imx: merge i.MX3 and i.MX6
arm/imx6q: add suspend/resume support
arm/imx6q: add device tree machine support
arm/imx6q: add smp and cpu hotplug support
arm/imx6q: add core drivers clock, gpc, mmdc and src
arm/imx: add gic_handle_irq function
arm/imx6q: add core definitions and low-level debug uart
arm/imx6q: add device tree source
ARM: highbank: add suspend support
ARM: highbank: Add cpu hotplug support
ARM: highbank: add SMP support
MAINTAINERS: add Calxeda Highbank ARM platform
ARM: add Highbank core platform support
ARM: highbank: add devicetree source
ARM: l2x0: add empty l2x0_of_init
picoxcell: add a definition of VMALLOC_END
picoxcell: remove custom ioremap implementation
picoxcell: add the DTS for the PC7302 board
picoxcell: add the DTS for pc3x2 and pc3x3 devices
...
Fix up trivial conflicts in arch/arm/Kconfig, and some more header file
conflicts in arch/arm/mach-omap2/board-generic.c (as per an ealier merge
by Arnd).
* 'next/dt' of git://git.linaro.org/people/arnd/arm-soc:
ARM: gic: use module.h instead of export.h
ARM: gic: fix irq_alloc_descs handling for sparse irq
ARM: gic: add OF based initialization
ARM: gic: add irq_domain support
irq: support domains with non-zero hwirq base
of/irq: introduce of_irq_init
ARM: at91: add at91sam9g20 and Calao USB A9G20 DT support
ARM: at91: dt: at91sam9g45 family and board device tree files
arm/mx5: add device tree support for imx51 babbage
arm/mx5: add device tree support for imx53 boards
ARM: msm: Add devicetree support for msm8660-surf
msm_serial: Add devicetree support
msm_serial: Use relative resources for iomem
Fix up conflicts in arch/arm/mach-at91/{at91sam9260.c,at91sam9g45.c}
* 'next/cleanup2' of git://git.linaro.org/people/arnd/arm-soc: (31 commits)
ARM: OMAP: Warn if omap_ioremap is called before SoC detection
ARM: OMAP: Move set_globals initialization to happen in init_early
ARM: OMAP: Map SRAM later on with ioremap_exec()
ARM: OMAP: Remove calls to SRAM allocations for framebuffer
ARM: OMAP: Avoid cpu_is_omapxxxx usage until map_io is done
ARM: OMAP1: Use generic map_io, init_early and init_irq
arm/dts: OMAP3+: Add mpu, dsp and iva nodes
arm/dts: OMAP4: Add a main ocp entry bound to l3-noc driver
ARM: OMAP2+: l3-noc: Add support for device-tree
ARM: OMAP2+: board-generic: Add i2c static init
ARM: OMAP2+: board-generic: Add DT support to generic board
arm/dts: Add support for OMAP3 Beagle board
arm/dts: Add initial device tree support for OMAP3 SoC
arm/dts: Add support for OMAP4 SDP board
arm/dts: Add support for OMAP4 PandaBoard
arm/dts: Add initial device tree support for OMAP4 SoC
ARM: OMAP: omap_device: Add a method to build an omap_device from a DT node
ARM: OMAP: omap_device: Add omap_device_[alloc|delete] for DT integration
of: Add helpers to get one string in multiple strings property
ARM: OMAP2+: devices: Remove all omap_device_pm_latency structures
...
Fix up trivial header file conflicts in arch/arm/mach-omap2/board-generic.c
* 'next/cross-platform' of git://git.linaro.org/people/arnd/arm-soc:
arm/imx: use Kconfig choice for low-level debug UART selection
ARM: realview: use Kconfig choice for debug UART selection
ARM: plat-samsung: use Kconfig choice for debug UART selection
ARM: versatile: convert logical CPU numbers to physical numbers
ARM: ux500: convert logical CPU numbers to physical numbers
ARM: shmobile: convert logical CPU numbers to physical numbers
ARM: msm: convert logical CPU numbers to physical numbers
ARM: exynos4: convert logical CPU numbers to physical numbers
Fix up trivial conflict (config DEBUG_S3C_UART move/split vs addition of
ARM_KPROBES_TEST option) in arch/arm/Kconfig.debug
* 'next/devel' of git://git.linaro.org/people/arnd/arm-soc: (50 commits)
ARM: tegra: update defconfig
arm/tegra: Harmony: Configure PMC for low-level interrupts
arm/tegra: device tree support for ventana board
arm/tegra: add support for ventana pinmuxing
arm/tegra: prepare Seaboard pinmux code for derived boards
arm/tegra: pinmux: ioremap registers
gpio/tegra: Convert to a platform device
arm/tegra: Convert pinmux driver to a platform device
arm/dt: Tegra: Add pinmux node to tegra20.dtsi
arm/tegra: Prep boards for gpio/pinmux conversion to pdevs
ARM: mx5: fix clock usage for suspend
ARM i.MX entry-macro.S: remove now unused code
ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLER
ARM i.MX tzic: add handle_irq function
ARM i.MX avic: add handle_irq function
ARM: mx25: Add the missing IIM base definition
ARM i.MX avic: convert to use generic irq chip
mx31moboard: Add poweroff support
ARM: mach-qong: Add watchdog support
ARM: davinci: AM18x: Add wl1271/wlan support
...
Fix up conflicts in:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-mx5/devices-imx53.h
arch/arm/plat-mxc/include/mach/memory.h
* 'next/board' of git://git.linaro.org/people/arnd/arm-soc: (34 commits)
ep93xx: add support Vision EP9307 SoM
ARM: mxs: Add initial support for DENX MX28
ARM: EXYNOS4: Add support SMDK4412 Board
ARM: EXYNOS4: Add MCT support for EXYNOS4412
ARM: EXYNOS4: Add functions for gic interrupt handling
ARM: EXYNOS4: Add support clock for EXYNOS4412
ARM: EXYNOS4: Add support new EXYNOS4412 SoC
ARM: EXYNOS4: Add support MCT PPI for EXYNOS4212
ARM: EXYNOS4: Add support PPI in external GIC
ARM: EXYNOS4: convert boot_params to atag_offset
ixp4xx: support omicron ixp425 based boards
ARM: EXYNOS4: Add support SMDK4212 Board
ARM: EXYNOS4: Add support PM for EXYNOS4212
ARM: EXYNOS4: Add support clock for EXYNOS4212
ARM: EXYNOS4: Add support new EXYNOS4212 SoC
at91: USB-A9G20 C01 & C11 board support
at91: merge board USB-A9260 and USB-A9263 together
at91: add support for RSIs EWS board
ARM: SAMSUNG: Fix mask value for S5P64X0 CPU IDs
ARM: SAMSUNG: Fix mask for S3C64xx CPU IDs
...
* 'next/deletion' of git://git.linaro.org/people/arnd/arm-soc:
ARM: mach-nuc93x: delete
Fix up trivial delete/edit conflicts in
arch/arm/mach-nuc93x/{Makefile.boot,mach-nuc932evb.c,time.c}
* 'next/pm' of git://git.linaro.org/people/arnd/arm-soc: (66 commits)
ARM: CSR: PM: use outer_resume to resume L2 cache
ARM: CSR: call l2x0_of_init to init L2 cache of SiRFprimaII
ARM: OMAP: voltage: voltage layer present, even when CONFIG_PM=n
ARM: CSR: PM: add sleep entry for SiRFprimaII
ARM: CSR: PM: save/restore irq status in suspend cycle
ARM: CSR: PM: save/restore timer status in suspend cycle
OMAP4: PM: TWL6030: add cmd register
OMAP4: PM: TWL6030: fix ON/RET/OFF voltages
OMAP4: PM: TWL6030: address 0V conversions
OMAP4: PM: TWL6030: fix uv to voltage for >0x39
OMAP4: PM: TWL6030: fix voltage conversion formula
omap: voltage: add a stub header file for external/regulator use
OMAP2+: VC: more registers are per-channel starting with OMAP5
OMAP3+: voltage: update nominal voltage in voltdm_scale() not VC post-scale
OMAP3+: voltage: rename omap_voltage_get_nom_volt -> voltdm_get_voltage
OMAP3+: voltdm: final removal of omap_vdd_info
OMAP3+: voltage: move/rename curr_volt from vdd_info into struct voltagedomain
OMAP3+: voltage: rename scale and reset functions using voltdm_ prefix
OMAP3+: VP: combine setting init voltage into common function
OMAP3+: VP: remove unused omap_vp_get_curr_volt()
...
Fix up trivial conflict in arch/arm/mach-prima2/l2x0.c (code removal vs
edit)
* 'next/driver' of git://git.linaro.org/people/arnd/arm-soc:
hw_random: add driver for atmel true hardware random number generator
ARM: at91: at91sam9g45: add trng clock and platform device
MX53 Enable the AHCI SATA on MX53 SMD board
MX53 Enable the AHCI SATA on MX53 LOCO board
MX53 Enable the AHCI SATA on MX53 ARD board
AHCI Add the AHCI SATA feature on the MX53 platforms
Fix pata imx resource
ARM: imx: Define functions for registering PATA
ARM: imx: Add PATA clock support
ARM: imx: Add PATA resources for other i.MX processors
imx: efika: Enable pata.
imx51: add pata clock
imx51: add pata device
Fix up trivial conflict (new selects next to each other from separate
branches for EFIKA_COMMON) in arch/arm/mach-mx5/Kconfig
* 'next/fixes' of git://git.linaro.org/people/arnd/arm-soc: (28 commits)
ARM: pxa/cm-x300: properly set bt_reset pin
ARM: mmp: rename SHEEVAD to GPLUGD
ARM: imx: Fix typo 'MACH_MX31_3DS_MXC_NAND_USE_BBT'
ARM: i.MX28: shift frac value in _CLK_SET_RATE
plat-mxc: iomux-v3.h: implicitly enable pull-up/down when that's desired
ARM: mx5: fix clock usage for suspend
ARM: pxa: use correct __iomem annotations
ARM: pxa: sharpsl pm needs SPI
ARM: pxa: centro and treo680 need palm27x
ARM: pxa: make pxafb_smart_*() empty when not enabled
ARM: pxa: select POWER_SUPPLY on raumfeld
ARM: pxa: pxa95x is incompatible with earlier pxa
ARM: pxa: CPU_FREQ_TABLE is needed for CPU_FREQ
ARM: pxa: pxa95x/saarb depends on pxa3xx code
ARM: pxa: allow selecting just one of TREO680/CENTRO
ARM: pxa: export symbols from pxa3xx-ulpi
ARM: pxa: make zylonite_pxa*_init declaration match code
ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available
ARM: at91: add defconfig for at91sam9g45 family
ARM: at91: remove dependency for Atmel PWM driver selector in Kconfig
...
* 'for-linus/i2c-3.2' of git://git.fluff.org/bjdooks/linux: (47 commits)
i2c-s3c2410: Add device tree support
i2c-s3c2410: Keep a copy of platform data and use it
i2c-nomadik: cosmetic coding style corrections
i2c-au1550: dev_pm_ops conversion
i2c-au1550: increase timeout waiting for master done
i2c-au1550: remove unused ack_timeout
i2c-au1550: remove usage of volatile keyword
i2c-tegra: __iomem annotation fix
i2c-eg20t: Add initialize processing in case i2c-error occurs
i2c-eg20t: Fix flag setting issue
i2c-eg20t: add stop sequence in case wait-event timeout occurs
i2c-eg20t: Separate error processing
i2c-eg20t: Fix 10bit access issue
i2c-eg20t: Modify returned value s32 to long
i2c-eg20t: Fix bus-idle waiting issue
i2c-designware: Fix PCI core warning on suspend/resume
i2c-designware: Add runtime power management support
i2c-designware: Add support for Designware core behind PCI devices.
i2c-designware: Push all register reads/writes into the core code.
i2c-designware: Support multiple cores using same ISR
...
The board changes in the imx/devel branch conflict with other changes in
the device imx/dt branch.
Conflicts:
arch/arm/mach-mx5/board-mx53_loco.c
arch/arm/mach-mx5/board-mx53_smd.c
arch/arm/plat-mxc/include/mach/common.h
arch/arm/plat-mxc/include/mach/memory.h
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are lots of conflicts between the omap and exynos cleanups
and the memory.h remove series.
Conflicts:
arch/arm/mach-exynos4/mach-smdkc210.c
arch/arm/mach-exynos4/mach-smdkv310.c
arch/arm/mach-imx/mach-cpuimx27.c
arch/arm/mach-omap1/board-ams-delta.c
arch/arm/mach-omap1/board-generic.c
arch/arm/mach-omap1/board-h2.c
arch/arm/mach-omap1/board-h3.c
arch/arm/mach-omap1/board-nokia770.c
arch/arm/mach-omap1/board-osk.c
arch/arm/mach-omap1/board-palmte.c
arch/arm/mach-omap1/board-palmtt.c
arch/arm/mach-omap1/board-palmz71.c
arch/arm/mach-omap1/board-sx1.c
arch/arm/mach-omap1/board-voiceblue.c
arch/arm/mach-omap1/io.c
arch/arm/mach-omap2/board-generic.c
arch/arm/mach-omap2/io.c
arch/arm/plat-omap/io.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The regulator support in the l4f00242t03 is very non-idiomatic. Rather
than requesting the regulators based on the device name and the supply
names used by the device the driver requires boards to pass system
specific supply names around through platform data. The driver also
conditionally requests the regulators based on this platform data, adding
unneeded conditional code to the driver.
Fix this by removing the platform data and converting to the standard
idiom, also updating all in tree users of the driver. As no datasheet
appears to be available for the LCD I'm guessing the names for the
supplies based on the existing users and I've no ability to do anything
more than compile test.
The use of regulator_set_voltage() in the driver is also problematic,
since fixed voltages are required the expectation would be that the
voltages would be fixed in the constraints set by the machines rather than
manually configured by the driver, but is less problematic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Things like module_param and core_param come from the header
moduleparam.h -- these files were relying on the fact that
module.h is implicitly present everywhere and it in turn
includes the moduleparam header.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files will fail to compile if we dont clean them up in advance
and have them include the appropriate headers they need.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files all make use of one of the EXPORT_SYMBOL variants
or the THIS_MODULE macro. So they will need <linux/export.h>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Many of the core ARM kernel files are not modules, but just
including module.h for exporting symbols. Now these files can
use the lighter footprint export.h for this role.
There are probably lots more, but ARM files of mach-* and plat-*
don't get coverage via a simple yesconfig build. They will have
to be cleaned up and tested via using their respective configs.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Building these files does not reveal a hidden need for
any of these. Since module.h brings in the whole kitchen
sink, it just needlessly adds 30k+ lines to the cpp burden.
There are probably lots more, but ARM files of mach-* and plat-*
don't get coverage via a simple yesconfig build. They will have
to be cleaned up and tested via using their respective configs.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
To fix messages like this:
CC arch/arm/plat-samsung/platformdata.o
arch/arm/plat-samsung/platformdata.c: In function 's3c_set_platdata':
arch/arm/plat-samsung/platformdata.c:29: error: 'GFP_KERNEL' undeclared (first use in this function)
arch/arm/plat-samsung/platformdata.c:29: error: (Each undeclared identifier is reported only once
arch/arm/plat-samsung/platformdata.c:29: error: for each function it appears in.)
make[3]: *** [arch/arm/plat-samsung/platformdata.o] Error 1
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
To fix this:
arch/arm/mach-bcmring/dma.c: In function 'dma_request_channel_dbg':
arch/arm/mach-bcmring/dma.c:1022: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
arch/arm/mach-bcmring/dma.c:1022: error: (Each undeclared identifier is reported only once
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Add the include to fix things like this:
arch/arm/mach-sa1100/jornada720.c:278: error: 'PAGE_SHIFT' undeclared here (not in a function)
arch/arm/mach-bcmring/mm.c:32: error: 'PAGE_SHIFT' undeclared here (not in a function)
arch/arm/mach-sa1100/collie.c:361: error: 'PAGE_SHIFT' undeclared here (not in a function)
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
To fix things like this:
arch/arm/mach-omap2/usb-tusb6010.c:58: error: implicit declaration of function 'memset'
arch/arm/kernel/leds.c:40: error: implicit declaration of function 'strcspn'
arch/arm/kernel/leds.c:40: warning: incompatible implicit declaration of built-in function 'strcspn'
arch/arm/kernel/leds.c:45: error: implicit declaration of function 'strncmp'
arch/arm/kernel/leds.c:55: error: implicit declaration of function 'strlen'
arch/arm/kernel/leds.c:55: warning: incompatible implicit declaration of built-in function 'strlen'
arch/arm/mach-omap2/clockdomain.c:52: error: implicit declaration of function 'strcmp'
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
It was implicitly getting it via an implicit presence of module.h
but when we clean that up, we'll get a bunch of lines like this:
arch/arm/kernel/ptrace.c:764: error: 'NT_PRSTATUS' undeclared here (not in a function)
arch/arm/kernel/ptrace.c:765: error: 'ELF_NGREG' undeclared here (not in a function)
arch/arm/kernel/ptrace.c:776: error: 'NT_PRFPREG' undeclared here (not in a function)
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The module.h cleanup series is not merged at this point, so use the
older header file for now, to make it build either way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The exynos4 updates conflict with code from the arm devel-stable branch
and new boards need to set atag_offset in place of boot_param.
Conflicts:
arch/arm/Kconfig
arch/arm/mach-exynos4/include/mach/entry-macro.S
arch/arm/mach-exynos4/mach-smdkc210.c
arch/arm/mach-exynos4/mach-smdkv310.c
arch/arm/mach-exynos4/mct.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The timer and cleanup branches from stericsson conflict,
so I'm merging them here.
Conflicts:
arch/arm/mach-ux500/Makefile
arch/arm/mach-ux500/cpu.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Omap cleanups conflicted with omap2_dss work in a nontrivial
way, this is the most logical fixup.
Conflicts:
arch/arm/mach-omap2/board-2430sdp.c
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-apollon.c
arch/arm/mach-omap2/board-h4.c
arch/arm/mach-omap2/board-ldp.c
arch/arm/mach-omap2/board-rx51.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The patch merges the build of imx3 and imx6. The Kconfig symbol
ARCH_IMX_V6_V7 is introduced to replace ARCH_MX3 and ARCH_MX6.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It adds a number of core drivers support for imx6q, including clock,
General Power Controller (gpc), Multi Mode DDR Controller(mmdc) and
System Reset Controller (src).
Signed-off-by: Ranjani Vaidyanathan <ra5478@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This is a plain translation of assembly gic irq handler to C function
for CONFIG_MULTI_IRQ_HANDLER support on imx family.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This adds cpu hotplug for highbank. On highbank, a core is always reset and
boots up the same path as a cold boot.
Signed-off-by: Martin Bogomolni <martin@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
This enables SMP support on highbank processor.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
This adds basic support for the Calxeda Highbank platform.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
This adds the devicetree source and documentation for the Calxeda highbank
platform.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Add empty version of l2x0_of_init for when CONFIG_CACHE_L2X0 is not selected.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Barry Song <21cnbao@gmail.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Commit "ARM: gic: add irq_domain support" (b49b6ff) breaks SPARSE_IRQ
on platforms with GIC. When SPARSE_IRQ is enabled, all NR_IRQS or
mach_desc->nr_irqs will be allocated by arch_probe_nr_irqs(). This caused
irq_alloc_descs to allocate irq_descs after the pre-allocated space.
Make irq_alloc_descs search for an exact irq range and assume it has
been pre-allocated on failure. For DT probing dynamic allocation is used.
DT enabled platforms should set their nr_irqs to NR_IRQ_LEGACY and have all
irq_chips allocate their irq_descs with irq_alloc_descs if SPARSE_IRQ is
enabled.
gic_init irq_start param is changed to be signed with negative meaning do
dynamic Linux irq assigment.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This adds ARM gic interrupt controller initialization using device tree
data.
The initialization function is intended to be called by of_irq_init
function like this:
const static struct of_device_id irq_match[] = {
{ .compatible = "arm,cortex-a9-gic", .data = gic_of_init, },
{}
};
static void __init init_irqs(void)
{
of_irq_init(irq_match);
}
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Convert the gic interrupt controller to use irq domains in preparation
for device-tree binding and MULTI_IRQ. This allows for translation between
GIC interrupt IDs and Linux irq numbers.
The meaning of irq_offset has changed. It now is just the number of skipped
GIC interrupt IDs for the controller. It will be 16 for primary GIC and 32
for secondary GICs.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (33 commits)
iommu/core: Remove global iommu_ops and register_iommu
iommu/msm: Use bus_set_iommu instead of register_iommu
iommu/omap: Use bus_set_iommu instead of register_iommu
iommu/vt-d: Use bus_set_iommu instead of register_iommu
iommu/amd: Use bus_set_iommu instead of register_iommu
iommu/core: Use bus->iommu_ops in the iommu-api
iommu/core: Convert iommu_found to iommu_present
iommu/core: Add bus_type parameter to iommu_domain_alloc
Driver core: Add iommu_ops to bus_type
iommu/core: Define iommu_ops and register_iommu only with CONFIG_IOMMU_API
iommu/amd: Fix wrong shift direction
iommu/omap: always provide iommu debug code
iommu/core: let drivers know if an iommu fault handler isn't installed
iommu/core: export iommu_set_fault_handler()
iommu/omap: Fix build error with !IOMMU_SUPPORT
iommu/omap: Migrate to the generic fault report mechanism
iommu/core: Add fault reporting mechanism
iommu/core: Use PAGE_SIZE instead of hard-coded value
iommu/core: use the existing IS_ALIGNED macro
iommu/msm: ->unmap() should return order of unmapped page
...
Fixup trivial conflicts in drivers/iommu/Makefile: "move omap iommu to
dedicated iommu folder" vs "Rename the DMAR and INTR_REMAP config
options" just happened to touch lines next to each other.
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (270 commits)
video: platinumfb: Add __devexit_p at necessary place
drivers/video: fsl-diu-fb: merge diu_pool into fsl_diu_data
drivers/video: fsl-diu-fb: merge diu_hw into fsl_diu_data
drivers/video: fsl-diu-fb: only DIU modes 0 and 1 are supported
drivers/video: fsl-diu-fb: remove unused panel operating mode support
drivers/video: fsl-diu-fb: use an enum for the AOI index
drivers/video: fsl-diu-fb: add several new video modes
drivers/video: fsl-diu-fb: remove broken screen blanking support
drivers/video: fsl-diu-fb: move some definitions out of the header file
drivers/video: fsl-diu-fb: fix some ioctls
video: da8xx-fb: Increased resolution configuration of revised LCDC IP
OMAPDSS: picodlp: add missing #include <linux/module.h>
fb: fix au1100fb bitrot.
mx3fb: fix NULL pointer dereference in screen blanking.
video: irq: Remove IRQF_DISABLED
smscufx: change edid data to u8 instead of char
OMAPDSS: DISPC: zorder support for DSS overlays
OMAPDSS: DISPC: VIDEO3 pipeline support
OMAPDSS/OMAP_VOUT: Fix incorrect OMAP3-alpha compatibility setting
video/omap: fix build dependencies
...
Fix up conflicts in:
- drivers/staging/xgifb/XGI_main_26.c
Changes to XGIfb_pan_var()
- drivers/video/omap/{lcd_apollon.c,lcd_ldp.c,lcd_overo.c}
Removed (or in the case of apollon.c, merged into the generic
DSS panel in drivers/video/omap2/displays/panel-generic-dpi.c)
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
ARM: mark empty gpio.h files empty
gpio: Fix ARM versatile-express build failure
of: include errno.h
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
h8300: Move gpio.h to gpio-internal.h
gpio: pl061: add DT binding support
gpio: fix build error in include/asm-generic/gpio.h
gpiolib: Ensure struct gpio is always defined
irq: Add EXPORT_SYMBOL_GPL to function of irq generic-chip
gpio-ml-ioh: Use NUMA_NO_NODE not GFP_KERNEL
gpio-pch: Use NUMA_NO_NODE not GFP_KERNEL
gpio: langwell: ensure alternate function is cleared
gpio-pch: Support interrupt function
gpio-pch: Save register value in suspend()
gpio-pch: modify gpio_nums and mask
gpio-pch: support ML7223 IOH n-Bus
gpio-pch: add spinlock in suspend/resume processing
gpio-pch: Delete invalid "restore" code in suspend()
gpio-ml-ioh: Fix suspend/resume issue
gpio-ml-ioh: Support interrupt function
gpio-ml-ioh: Delete unnecessary code
gpio/mxc: add chained_irq_enter/exit() to mx3_gpio_irq_handler()
gpio/nomadik: use genirq core to track enablement
gpio/nomadik: disable clocks when unused
It is generally a better idea to make intentionally empty files
contain the human-readable /* empty */ comment, also it makes
the files play nice with "make distclean".
Reported-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
A missing mach/gpio.h prevents building gpiolib on versatile express.
CC drivers/gpio/gpiolib.o
In file included from /.../linux/include/linux/gpio.h:18:0,
from /.../linux/drivers/gpio/gpiolib.c:10:
/.../linux/arch/arm/include/asm/gpio.h:5:23: fatal error: mach/gpio.h: No such file or directory
compilation terminated.
make[3]: *** [drivers/gpio/gpiolib.o] Error 1
make[2]: *** [drivers/gpio] Error 2
make[1]: *** [drivers] Error 2
make: *** [sub-make] Error 2
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
