In ieee80211.h the uapsd bit mask is defined such that
VO=BIT(0), VI=BIT(1), BK=BIT(2), BE=BIT(3).
The firmware uses the indexing as defined in the ieee80211
spec, meaning that VO=3, VI=2, BK=1, BE=0.
In AP mode when adding peer wlcore needs to convert
the indexing accordingly.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Save the ht_cap IE per-band, so we can configure different
params to BG and A bands (we currently don't support MIMO
on A band)
[Small fix for rx_highest - Arik]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add a dependency on mac80211 in Kconfig, and also replace some spaces
with tabs.
Reported-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
With the new FW (sigle role X.3.8.0.108, multi role X.5.4.0.21)
we are supporting 3 RX BA sessions, this change is to support this
new ability.
Signed-off-by: Assaf Azulay <assaf@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Modify default parameters to reduce firmware BSS lose
probability in congested environment.
[Applied to 18xx configuration as well - Arik]
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Make sure the deauth bcast gets sent
[Make sure we are AP as well before the flush - Arik]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Multicast management frames (e.g. global deauth)
should be sent out on the bcast link, rather than
the global, which should be used only for pre-added
stations (e.g. for auth/assoc resp).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We can't use cancel_delayed_work_sync() from functions that take the
wl->mutex, since connection_loss_work also takes the mutex. This might
result in a deadlock. Restructure the code so the work is synchronously
canceled before taking the mutex.
Avoid a bug where we would indefinitely delay the connection loss
indication by re-queuing the connection loss work on consecutive beacon
loss events.
Cc: bartosz.markowski <bartosz.markowski@tieto.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In patch d7b63b9fc7 we have raised the dynamic
PS timeout to 200ms to improve user experience. Re-apply the change,
since it was reverted in the wlcore split.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The "static" modifier was mistakenly forgotten for some functions.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Commit 4afc37 (wlcore: reorder identify_chip and get_hw_info) broke
support for wl127x chips.
When we moved the identify_chip operation to an earlier stage (ie. to
the probe function), we broke wl127x support because during HW init we
would set the WLCORE_QUIRK_TX_BLOCKSIZE_ALIGN.
To avoid this, set this quirk in the identify_chip operations and only
force it to be unset if the bus module doesn't support it. We were
doing the opposite and setting the flag if the bus module supports it.
Signed-off-by: Luciano Coelho <coelho@ti.com>
as tcp check sum is going to be removed from firmware, and as
there is a problem with getting dns in security when checksum is
enabled, it was decided to disable it by default.
for none security modes it can be enabled by module paramenter.
Signed-off-by: Assaf Azulay <assaf@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some of the structures were updated, other structures had a few
missing values and a few new ones were added. Change the driver
structs accordingly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Now the firmware can support TX block ack sessions with 64 frames.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
With 4 pages (16Kb), we can't fit 10 frames in the aggregation buffer
during iperf. This is the optimal for the firmware. Thus, increase
the buffer size by one page.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Instead of adding more files from the lower drivers into the same
directory in debugfs as wlcore, we now add a subdirectory for the
lower driver. This makes things a bit easier, because we can quickly
see where the debugfs entry is implemented and what is specific to the
lower driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Yet another temporary module parameter requested by the firmware team.
This will be replaced by the conf binary.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We use hardcoded values for the different board types. In some cases
we may need to override the defaults, so export the values as module
params. If not defined, the defaults for the specified board type
will be used.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
With more recent PHY firmware versions (>8.1.0.0.116), we need to use
the correct value for the pwr_limit_reference_11_abg parameter when
setting the mac_and_phy options.
For now we use a hardcoded 0xc8 as the value. This will be moved to
the configuration binary when it gets implemented.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
In some cases it may be useful to force narrow-band SISO channels.
Add a new value to the ht_mode module parameter to force the device to
operate in SISO 20MHz.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We were setting all the rates bits when starting the AP role. Instead
of doing this, we should set only the rates we really support
(eg. MIMO rates or wide-channel rates). This commit changes that so
that we always use the default rates (basic rates + MCS0-7) and add
the values returned by the ap_get_mimo_wide_rate_mask operation.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
If the wl18xx module is loaded with ht_mode=wide (the default), we
shouldn't use MIMO rates when the channel type is not HT40. Fix this
by checking the ht_mode before deciding which rates to used.
Additionally, set the ht_mode parameter explicitly to "wide" as the
default.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
In some cases it may be useful for debugging to check what is the
status of the interrupt register when a hardware recovery happens.
Print the contents of REG_INTERRUPT_NO_CLEAR (aka. HINT_STS_RAW) when
recovery starts.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The wl18xx firmware writes the PHY firmware version in the static
data. Add an operation to parse the static data and print the PHY
firmware version when booting.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The wl18xx firmware has more information in the static_data than
wl12xx. To be able to parse that in an abstracted way, this patch
adds a priv area to the static data struct and an operation that
allows the lower driver to parse it if necessary.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Implement the operations that are necessary to fetch the
wl18xx-specific FW statistics and export them in debugfs.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Implement the operations that are necessary to fetch the
wl12xx-specific FW statistics. Re-add some of the code removed from
wlcore.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add a macro to make it easy to print arrays from the FW statistics
array in debugfs. At the same time, increase the buffer size so
arrays fit more easily.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The FW statistics differ from hardware to hardware. This commit
prepares for hardware-specific implementation of the FW statistics
debugfs entries.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Sometimes we get a BSS_CHANGED_BEACON_ENABLED event before the basic
rates have been properly set. To avoid problems with the firmware not
expecting to receive frames at rates that are not set during
CMD_START_ROLE, we now start with all basic rates by default.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
When the data rates change, we get BSS_CHANGED_BASIC_RATES. At this
point, we should update all the templates to match the new rates. We
were changing some of the templates, but the beacon and the probe
response templates were missing.
[Remove redundant min_rate variable - Arik]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
There are some problems with MCS_13 in PG 1.0 hardware. So we disable
it when PG 1.0 is detected.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We can do get the HW information and identify the chip already at
probe time. This makes it easier to mangle with the parameters during
identify chip before registering the hardware with mac80211.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Like HDK, COM8 uses 0x06 for the low_band_component_type as well.
Hardcode the value for COM8 until this configuration can be done in
the external configuration binary (to be implemented).
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
When allocating the fw_status structure, the space for the
lower-driver private area was missing. This was causing an illegal
write outside the allocated area, which was causing random oopses
around the kernel.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Since the most common board we're using now is an HDK board, change
the default board_type to hdk.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We were changing the low_band_component_type in the private
configuration structure before copying the default values to it, so
the change was overwritten and only took effect after HW recovery.
Reported-by: Dror Erez <drorer@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
In some cases we may want to dump all the SDIO data in order to get
detailed information for debugging the communication with the
firmware.
Add printks to dump the data and a module parameter to enable/disable
it.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
In wl18xx we don't have an NVS yet, so we need to control whether 11a
is supported with a module parameter for now. 11a support is enabled
by default and can be changed by setting enable_11a to false when
loading the module.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add the get_mac operation in order to fetch the BD_ADDR from fuse ROM,
so that we can derive the WLAN MAC addresses from it.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The number of RX packet descriptors may vary from chip to chip and
in different firmware versions. Unfortunately, the array that
contains the actual descriptors is in the middle of the fw_status
structure. To manage this, we split the struct into two so we can
calculate the offset of what comes after the array and access the last
elements more easily.
[Changed the STATUS_LEN macro to be placement agnostic - Arik]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We need to specify the number of 2.4GHz and 5GHz antennas and whether
the board has an internal or external DC2DC. Add some module
parameters that allow changing that.
In the future this will come from the "NVS" file.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Currently, all HDK boards use low_band_component_type 0x06. In the
future this may change, but for now, we hardcode this value when the
board_type is set to HDK.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add the correct FW name for PLT (which is the same as the normal
firmware) and implement the plt_init operation.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
PLT mode needs to be initialized differently for each chip. This
patch adds an operation to init PLT and moves the existing PLT
initialization into the wl12xx driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add more board types and remove a now unneeded write to SCR_PAD2 setting
the board type.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In this chip family the NVS file should not be uploaded to FW. In fact,
we encounter strange bugs (sdio errors) when trying to upload it with
certain parameters.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This ensures the index is 0 on FW recovery and prevents spurious error
prints - "WARNING illegal id in tx completion".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Only wl127x chips use the rx_mem_pool_addr values, which need to be
given to the firmware as part of the RX path. Move this from core to
the wl12xx driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Read the HW PG version of the 18xx chip from FUSE.
Based on an earlier patch by Luciano Coelho <coelho@ti.com>.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Only wl12xx needs to get the ref_clock anc tcxo_clock values from the
platform data. Move these elements from the wl1271 structure to
wl12xx's private data.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The wl12xx.h file now contains mostly definitions that are internal to
wlcore. Still, some things need to me moved to the public header, so
for now we keep including it in wlcore.h.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Instead of using hardcoded values for a single frequency, we need to
read the frequency and use the appropriate values for it in the top
initialization.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Define the FW pc in the 18xx register translation table. This specific
register is only valid in the boot partition, so change the momentarily
change partitions. This doesn't damage 12xx cards, where the FW pc is
accessible via boot partition as well.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The firmware uses the SCR_PAD2 register to read the board type passed
from the driver. The values don't match the ones used in the mac and
phy configuration, so we need to map them before writing. This commit
adds a translation table that is used when writing the board type to
SCR_PAD2.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Different board types (ie. FPGA, HDK and DVP/EVB) require slightly
different init configuration options. Since we cannot probe the type
of board from the actual hardware, we need to pass it as an option
during module load.
This patch adds a module parameters that accepts the 3 different board
types, with DVP/EVB as the default, and uses this value where needed.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Set an alternate HT cap allowing MIMO rates (but only 20mhz) channels,
when the module is loaded with ht_mode=mimo.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Define the default HT capabilities of the 18xx chip family - these include
support for wide-channel.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add a HW op to add extra enabled rates for AP-mode data-rates. Since
the rates might depend on channel properties, reconfigure AP-mode rates
when these change.
Implement the HW op for the 18xx family, where MIMO or wide-chan rates
can be added.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Parse the peer ht_cap element containing MCS8-MCS15 rates and pass it
to the FW. Rates unsupported by the HW will be sanitized by mac80211
before reaching us.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Translate the NL80211 channel type to a FW-specific channel type and send
it to the FW as part of the role-start command. For wl12xx this has no
effect - this element is treated as padding.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Track the current 802.11 channel type, defaulting to a NO_HT channel.
Update the channel type element when changed by mac80211.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Now wlcore requires the lower drivers to set the correct
configuration. Move the existing private configuration to the proper
place and add all generic configuration parameters.
The important changes are in Tx interrupt pacing and Rx BA window size.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Some chip families can checksum certain classes of Rx packets in FW.
Implement the Rx-checksum feature as a HW-op. For the 18xx chip-family,
set Rx-checsum according to indication from FW.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some chip families are capable of checksumming certain classes of Tx
packets in HW. Indicate this fact in the netdev features and perform the
HW checksum by protocol type for the 18xx family.
Fix the location of the skb network header when we move it so we can
rely on it when setting the checksum.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Implement immediate Tx completion for the 18xx family. Move 18xx
specific Tx code to new tx.c/h files and create helper header files
for definitions.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Implement the 18xx-specific way for getting the length of a Rx packet.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Implement the HW op for getting alignment state in wl18xx. The FW aligns
the Rx Ethernet payload data.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl18xx chip passes extra information in the firmware status to the
driver. Add a private data section to handle that.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Define HW-rate conversion tables for the 18xx chip. Initialize
the appropriate wlcore elements with these tables and values to allow
conversion of HW-rates.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Set the frame length during Tx in a way compatible with the 18xx FW.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add the 18xx variant to the HW Tx descriptor union and set the 18xx
specific values during Tx.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize the Tx spare block counts for all operating modes in the 18xx
card.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize the number of Tx-descriptors for the 18xx family.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Make use of the wlcore provided private storage in the 18xx low-level
driver.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add the operations that allow wlcore to trigger commands to the
firmware and acknowledge when an event has been fully received.
Allocate a private buffer to hold the maximum sized cmd. Send the
entire length of the buffer each time a command is sent to signal
EOT. Remove the previous EOT mechanism.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Implement the boot operation. Add a wl18xx-specific configuration
structure (namely to configure the mac and phy parameters).
The default hw configuration matches the DVP board.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add identify_chip operation to detect the chip ID for wl185x and set
the correct firmware name.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add the register table with the appropriate values for wl18xx.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We don't have any chip-specific operations yet, but now wlcore has
defined an operations structure and requires the pointer to be set.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
At least in PG1, the wl18xx chips use the same SDIO vendor/device ID,
so it's not possible to figure out which driver is to be used. As a
workaround, we can check the SDIO revision number, because wl18xx uses
3.00 and wl12xx does not.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add the wl18xx module and the probe functions. Use wlcore for the
main parts (not functional at this point due to differences in the
wl18xx initialization).
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
skb_defer_rx_timestamp was called with a freshly allocated skb but must
be called with rskb instead.
Signed-off-by: Stephan Gatzka <stephan@gatzka.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add .status callback that detects link state changes.
Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver).
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead
of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY
register greater than the maximum allowed by the latter macro, and fix a
typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan.
Also for clarity, rename a few defines as bit definitions instead of masks.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is another fixup where the data is not transfered into buffer
addressed by skb->data but into a page.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
when register_netdev fails, the init'ed NAPIs by netif_napi_add must be
deleted with netif_napi_del, and also when driver unloads, it should
delete the NAPI before unregistering netdevice using unregister_netdev.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we terminate the eeprom access through clearing the CS by:
RTL_W8 (Cfg9346, ~EE_CS); or writeb (~EE_CS, ee_addr);
This would left the eeprom into "Config. Register Write Enable:"
state which is not expcted as the highest two bits were set to
0x11 ( expected is the "Normal" mode (0x00)). Solving this by write
0x0 instead of ~EE_CS when terminating the eeprom access.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we enable the receiver before setting the ring address which could
lead the card DMA into unexpected areas. Solving this by set the ring address
before enabling the receiver.
btw. I find and test this in qemu as I didn't have a 8139cp card in hand. please
review it carefully.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "!mlx4_is_slave" is totally confusing. Fix with
constant MLX4_CMD_NATIVE, which is the intended behavior.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The range check was performed after using the port number.
Reverse this to prevent a potential array overflow.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- pass the following parameters:
- firmware version (added QUERY_FW paravirtualization for that)
- disable Blueflame on slaves. KVM disables write combining on guests,
and we get better performance without BF in this case. (This requires
QUERY_DEV_CAP paravirtualization, also in this commit)
- max qp rdma as destination
- get rid of a chunk of "if (0)" dead code
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
