During detection the logic on the NAND bus is:
/* Regular ONFI detection */
1/ read the three NAND parameter pages
/* Extended parameter page detection */
2/ send "read the NAND parameter page" commands without reading
actual data
3/ move the column pointer to the extended page and read it
If fact, as long as there is nothing happening on the NAND bus between
1/ and 3/, the operation 2/ is redundant so remove it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-8-miquel.raynal@bootlin.com
Before reworking a little bit the ONFI detection code, let's
clean the coding style of the if statements to improve readability.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-5-miquel.raynal@bootlin.com
During ONFI detection, the CRC derived from the parameter page and the
CRC supposed to be at the end of the parameter page are compared. If
they do not match, the second then the third copies of the page are
tried.
The current implementation compares the newly derived CRC with the CRC
contained in the first page only. So if this particular CRC area has
been corrupted, then the detection will fail for a wrong reason.
Fix this issue by checking the derived CRC against the right one.
Fixes: 39138c1f4a ("mtd: rawnand: use bit-wise majority to recover the ONFI param page")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-4-miquel.raynal@bootlin.com
tR and tCCS are currently wrongly expressed in femtoseconds, while we
expect these values to be expressed in picoseconds. Set right
hardcoded values.
Fixes: 6a943386ee mtd: rawnand: add default values for dynamic timings
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-3-miquel.raynal@bootlin.com
Convert the timings union into a structure containing the mode and the
actual values. The values are still a union in prevision of the
addition of the NVDDR modes.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-2-miquel.raynal@bootlin.com
There is no correction involved at this point, it is just a matter of
reading registers and checking whether bitflips have occurred or
not. Rename the function to clarify it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-7-miquel.raynal@bootlin.com
Do not call nand_release() while the MTD device has not been
registered, use nand_cleanup() instead.
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-4-miquel.raynal@bootlin.com
Switch from the old platform_get_resource()/devm_ioremap_resource()
couple to the newer devm_platform_ioremap_resource() helper.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-3-miquel.raynal@bootlin.com
In a previous fix, I changed the condition on which the timeout of an
IRQ is reached from:
if (!ret)
into:
if (ret && !pending)
While having a non-zero return code is usual in the Linux kernel, here
ret comes from a wait_for_completion_timeout() which returns 0 when
the waiting period is too long.
Hence, the revised condition should be:
if (!ret && !pending)
The faulty patch did not produce any error because of the !pending
condition so this change is finally purely cosmetic and does not
change the actual driver behavior.
Fixes: cafb56dd74 ("mtd: rawnand: marvell: prevent timeouts on a loaded machine")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-2-miquel.raynal@bootlin.com
When the ECC strength is too weak compared to the NAND chip
requirements, display the values so that it is clear for people how
much they are far from the requirements (and might get in troubles in
the future).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200421163906.7515-1-miquel.raynal@bootlin.com
We are about to re-use those for the exec_op() implementation which
will not rely on au1550_hwcontrol(). Let's patch those helpers to
simply use the iomem address stored in the context.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200419193037.1544035-2-boris.brezillon@collabora.com
The Denali IP have several registers to specify how many clock cycles
should be waited between falling/rising signals. You can improve the
NAND access performance by programming these registers with optimized
values.
Because struct nand_sdr_timings represents the device requirement
in pico seconds, denali_setup_data_interface() computes the register
values by dividing the device timings with the clock period.
Marek Vasut reported this driver in the latest kernel does not work
on his SOCFPGA board. (The on-board NAND chip is mode 5)
The suspicious parameter is acc_clks, so this commit relaxes it.
The Denali NAND Flash Memory Controller User's Guide describes this
register as follows:
acc_clks
signifies the number of bus interface clk_x clock cycles,
controller should wait from read enable going low to sending
out a strobe of clk_x for capturing of incoming data.
Currently, acc_clks is calculated only based on tREA, the delay on the
chip side. This does not include additional delays that come from the
data path on the PCB and in the SoC, load capacity of the pins, etc.
This relatively becomes a big factor on faster timing modes like mode 5.
Before supporting the ->setup_data_interface() hook (e.g. Linux 4.12),
the Denali driver hacks acc_clks in a couple of ways [1] [2] to support
the timing mode 5.
We would not go back to the hard-coded acc_clks, but we need to include
this factor into the delay somehow. Let's say the amount of the additional
delay is 10000 pico sec.
In the new calculation, acc_clks is determined by timings->tREA_max +
data_setup_on_host.
Also, prolong the RE# low period to make sure the data hold is met.
Finally, re-center the data latch timing for extra safety.
[1] https://github.com/torvalds/linux/blob/v4.12/drivers/mtd/nand/denali.c#L276
[2] https://github.com/torvalds/linux/blob/v4.12/drivers/mtd/nand/denali.c#L282
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200317071821.9916-1-yamada.masahiro@socionext.com
->exec_op() is passed a check_only argument that encodes when the
controller should just check whether the operation is supported or not
without executing it. Some controllers simply ignore this arguments,
others don't but keep modifying some of the registers before returning.
Let's fix all those drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200418194217.1016060-1-boris.brezillon@collabora.com
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200417101129.35556-1-yuehaibing@huawei.com
Fix sparse warning:
drivers/mtd/nand/raw/cadence-nand-controller.c:2595:5:
warning: symbol 'cadence_nand_attach_chip' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200410115228.30440-1-yuehaibing@huawei.com
Fix sparse warning:
drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c:105:32:
warning: symbol 'qi_lb60_ooblayout_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200410115121.11852-1-yuehaibing@huawei.com
No need to use expensive atomic change_bit() on dat[] and err_idx[]:
1. fsmc_bch8_correct_data() is called while mutex chip->lock is held
2. err_idx[] is a local variable.
To avoid big endian concern due to type cast to unsigned long, directly
change the bit in the specified byte instead of using non-atomic
__change_bit().
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1576886755-9788-1-git-send-email-fenghua.yu@intel.com
Use Joe Perches cvt_fallthrough.pl script to convert
/* fallthrough */
comments (and its derivatives) into a
fallthrough;
statement. This automatically drops useless ones.
Do it MTD-wide.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/linux-mtd/20200325212115.14170-1-miquel.raynal@bootlin.com
* Add support for manufacturer specific suspend/resume operation
* Add support for manufacturer specific lock/unlock operation
* Replace zero-length array with flexible-array member
* Fix a typo ("manufecturer")
* Ensure nand_soft_waitrdy wait period is enough
Raw NAND controller driver changes:
* Brcmnand:
Add support for flash-edu for dma transfers (+ bindings)
* Cadence:
Reinit completion before executing a new command
Change bad block marker size
Fix the calculation of the avaialble OOB size
Get meta data size from registers
* Qualcom:
Use dma_request_chan() instead dma_request_slave_channel()
Release resources on failure within qcom_nandc_alloc()
* Allwinner:
Use dma_request_chan() instead dma_request_slave_channel()
* Marvell:
Use dma_request_chan() instead dma_request_slave_channel()
Release DMA channel on error
* Freescale:
Use dma_request_chan() instead dma_request_slave_channel()
* Macronix:
Add support for Macronix NAND randomizer (+ bindings)
* Ams-delta:
Rename structures and functions to gpio_nand*
Make the driver custom I/O ready
Drop useless local variable
Support custom driver initialisation
Add module device tables
Handle more GPIO pins as optional
Make read pulses optional
Don't hardcode read/write pulse widths
Push inversion handling to gpiolib
Enable OF partition info support
Drop board specific partition info
Use struct gpio_nand_platdata
Write protect device during probe
* Ingenic:
Use devm_platform_ioremap_resource()
Add dependency on MIPS || COMPILE_TEST
* Denali:
Deassert write protect pin
* ST:
Use dma_request_chan() instead dma_request_slave_channel()
Raw NAND chip driver changes:
* Toshiba:
Support reading the number of bitflips for BENAND (Built-in ECC NAND)
* Macronix:
Add support for deep power down mode
Add support for block protection
SPI-NAND core changes:
* Do not erase the block before writing a bad block marker
* Explicitly use MTD_OPS_RAW to write the bad block marker to OOB
* Stop using spinand->oobbuf for buffering bad block markers
* Rework detect procedure for different READ_ID operation
SPI-NAND driver changes:
* Toshiba:
Support for new Kioxia Serial NAND
Rename function name to change suffix and prefix (8Gbit)
Add comment about Kioxia ID
* Micron:
Add new Micron SPI NAND devices with multiple dies
Add M70A series Micron SPI NAND devices
identify SPI NAND device with Continuous Read mode
Add new Micron SPI NAND devices
Describe the SPI NAND device MT29F2G01ABAGD
Generalize the OOB layout structure and function names
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl5+XuIACgkQJWrqGEe9
VoRCAggAh0bpso9l8enk+ae1LrEGGLCV0sWMBy/pwM4zaBovqJqSdXRybg1IQE1N
5AvZrcQUBzdr9RzusB0J/xVC31gStjNQJROekArHJI6rzjoHRM/779fx0JV1JJHI
sWgX7UY7AVMH1l4BMB0mMezFeqJnZU5JRHQ+we3X4funNJ2JcBwvp1u4XJ2BDLRn
oCDLYgMC9S4lWEP7/ARgv27w7GfaegCUqNOHBVH75d2c+l476z5TKUap8s/LjI8u
8eRGerwLTj8/PLj1OqSEKXeJem2gZvZNpDCylgzrGZbU9r0M5I/EdXxJ90Pj6bR0
+G/0JHb4C1DXeDXzw79KisggHDkUUA==
=Zmzp
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.7' into mtd/next
Raw NAND core changes:
* Add support for manufacturer specific suspend/resume operation
* Add support for manufacturer specific lock/unlock operation
* Replace zero-length array with flexible-array member
* Fix a typo ("manufecturer")
* Ensure nand_soft_waitrdy wait period is enough
Raw NAND controller driver changes:
* Brcmnand:
Add support for flash-edu for dma transfers (+ bindings)
* Cadence:
Reinit completion before executing a new command
Change bad block marker size
Fix the calculation of the avaialble OOB size
Get meta data size from registers
* Qualcom:
Use dma_request_chan() instead dma_request_slave_channel()
Release resources on failure within qcom_nandc_alloc()
* Allwinner:
Use dma_request_chan() instead dma_request_slave_channel()
* Marvell:
Use dma_request_chan() instead dma_request_slave_channel()
Release DMA channel on error
* Freescale:
Use dma_request_chan() instead dma_request_slave_channel()
* Macronix:
Add support for Macronix NAND randomizer (+ bindings)
* Ams-delta:
Rename structures and functions to gpio_nand*
Make the driver custom I/O ready
Drop useless local variable
Support custom driver initialisation
Add module device tables
Handle more GPIO pins as optional
Make read pulses optional
Don't hardcode read/write pulse widths
Push inversion handling to gpiolib
Enable OF partition info support
Drop board specific partition info
Use struct gpio_nand_platdata
Write protect device during probe
* Ingenic:
Use devm_platform_ioremap_resource()
Add dependency on MIPS || COMPILE_TEST
* Denali:
Deassert write protect pin
* ST:
Use dma_request_chan() instead dma_request_slave_channel()
Raw NAND chip driver changes:
* Toshiba:
Support reading the number of bitflips for BENAND (Built-in ECC NAND)
* Macronix:
Add support for deep power down mode
Add support for block protection
SPI-NAND core changes:
* Do not erase the block before writing a bad block marker
* Explicitly use MTD_OPS_RAW to write the bad block marker to OOB
* Stop using spinand->oobbuf for buffering bad block markers
* Rework detect procedure for different READ_ID operation
SPI-NAND driver changes:
* Toshiba:
Support for new Kioxia Serial NAND
Rename function name to change suffix and prefix (8Gbit)
Add comment about Kioxia ID
* Micron:
Add new Micron SPI NAND devices with multiple dies
Add M70A series Micron SPI NAND devices
identify SPI NAND device with Continuous Read mode
Add new Micron SPI NAND devices
Describe the SPI NAND device MT29F2G01ABAGD
Generalize the OOB layout structure and function names
The suffix was changed from "G" to "J" to classify between 1st generation
and 2nd generation serial NAND devices (which now belong to the Kioxia
brand).
As reference that's
1st generation device of 1Gbit product is "TC58CVG0S3HRAIG"
2nd generation device of 1Gbit product is "TC58CVG0S3HRAIJ".
The 8Gbit type "TH58CxG3S0HRAIJ" is new to Kioxia's serial NAND lineup and
the prefix was changed from "TC58" to "TH58".
Thus the functions were renamed from tc58cxgxsx_*() to tx58cxgxsxraix_*().
Signed-off-by: Yoshio Furuyama <ytc-mb-yfuruyama7@kioxia.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/0dedd9869569a17625822dba87878254d253ba0e.1584949601.git.ytc-mb-yfuruyama7@kioxia.com
Macronix AD series support deep power down mode for a minimum
power consumption state.
Overload nand_suspend() & nand_resume() in Macronix specific code to
support deep power down mode.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add device table for new Micron SPI NAND devices, which have multiple
dies.
Also, enable support to select the dies.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200311175735.2007-7-sshivamurthy@micron.com
Add SPINAND_HAS_CR_FEAT_BIT flag to identify the SPI NAND device with
the Continuous Read mode.
Some of the Micron SPI NAND devices have the "Continuous Read" feature
enabled by default, which does not fit the subsystem needs.
In this mode, the READ CACHE command doesn't require the starting column
address. The device always output the data starting from the first
column of the cache register, and once the end of the cache register
reached, the data output continues through the next page. With the
continuous read mode, it is possible to read out the entire block using
a single READ command, and once the end of the block reached, the output
pins become High-Z state. However, during this mode the read command
doesn't output the OOB area.
Hence, we disable the feature at probe time.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200311175735.2007-5-sshivamurthy@micron.com
Add the SPI NAND device MT29F2G01ABAGD series number, size and voltage
details as a comment.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200311175735.2007-3-sshivamurthy@micron.com
In order to add new Micron SPI NAND devices, we generalized the OOB
layout structure and function names.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200311175735.2007-2-sshivamurthy@micron.com
Legacy mips soc platforms that have controller v5.0 and 6.0 use
flash-edu block for dma transfers. This change adds support for
nand dma transfers using the EDU block.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200122213313.35820-4-kdasu.kdev@gmail.com
Increase bad block marker size from one byte to two bytes.
Bad block marker is handled by skip bytes feature of HPNFC.
Controller expects this value to be an even number.
Fixes: ec4ba01e89 ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581328530-29966-3-git-send-email-piotrs@cadence.com
The value of cdns_chip->sector_count is not known at the moment
of the derivation of ecc_size, leading to a zero value. Fix
this by assigning ecc_size later in the code.
Fixes: ec4ba01e89 ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581328530-29966-2-git-send-email-piotrs@cadence.com
Add checking size of BCH meta data size in capabilities registers
instead of using fixed value. BCH meta data is used to keep data
from NAND flash OOB area.
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581328530-29966-1-git-send-email-piotrs@cadence.com
This driver has no arch-specific instructions but is only ever useful
on MIPS; so disable this driver if we're not compiling for MIPS, unless
the driver is compile-tested.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200302184509.10666-1-paul@crapouillou.net
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
Use using dma_request_chan() directly and inform user of error in case the
DMA request failed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-8-peter.ujfalusi@ti.com
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
Use using dma_request_chan() directly to return the real error code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-7-peter.ujfalusi@ti.com
In case when DMA channel request or alloc_bam_transaction() fails,
dma_unmap_single() and any channels already requested should be released.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-6-peter.ujfalusi@ti.com
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-5-peter.ujfalusi@ti.com
