Commit Graph

147093 Commits

Author SHA1 Message Date
Yoni Divinsky
2e42c203a9 wlcore: use psd_type indexing according to spec
In ieee80211.h the uapsd bit mask is defined such that
VO=BIT(0), VI=BIT(1), BK=BIT(2), BE=BIT(3).
The firmware uses the indexing as defined in the ieee80211
spec, meaning that VO=3, VI=2, BK=1, BE=0.

In AP mode when adding peer wlcore needs to convert
the indexing accordingly.

Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-05 20:24:31 +03:00
Eliad Peller
bfb92ca133 wlcore: set wl->ht_cap per-band
Save the ht_cap IE per-band, so we can configure different
params to BG and A bands (we currently don't support MIMO
on A band)

[Small fix for rx_highest - Arik]

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-05 17:16:09 +03:00
Arik Nemtsov
a121a5b8ab wl18xx: add dependency on mac80211
Add a dependency on mac80211 in Kconfig, and also replace some spaces
with tabs.

Reported-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-05 17:16:09 +03:00
Assaf Azulay
0a15d9b589 wlcore: increase number of BA sessions to 3
With the new FW (sigle role X.3.8.0.108, multi role X.5.4.0.21)
we are supporting 3 RX BA sessions, this change is to support this
new ability.

Signed-off-by: Assaf Azulay <assaf@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-05 17:16:08 +03:00
Igal Chernobelsky
7b052214e5 wlcore: modify bss loss parameters
Modify default parameters to reduce firmware BSS lose
probability in congested environment.

[Applied to 18xx configuration as well - Arik]

Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-05 17:16:08 +03:00
Eliad Peller
b515d83a29 wlcore: flush before stopping AP
Make sure the deauth bcast gets sent

[Make sure we are AP as well before the flush - Arik]

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-05 17:16:08 +03:00
Eliad Peller
45b60f7ddd wlcore: use correct link for bcast/multicast frames
Multicast management frames (e.g. global deauth)
should be sent out on the bcast link, rather than
the global, which should be used only for pre-added
stations (e.g. for auth/assoc resp).

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-05 17:16:08 +03:00
Arik Nemtsov
6b8bf5bc5e wlcore: fixes for connection_loss_work
We can't use cancel_delayed_work_sync() from functions that take the
wl->mutex, since connection_loss_work also takes the mutex. This might
result in a deadlock. Restructure the code so the work is synchronously
canceled before taking the mutex.
Avoid a bug where we would indefinitely delay the connection loss
indication by re-queuing the connection loss work on consecutive beacon
loss events.

Cc: bartosz.markowski <bartosz.markowski@tieto.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-05 17:16:08 +03:00
Arik Nemtsov
6e066921b3 wlcore: fix dynamic_ps_timeout time regression
In patch d7b63b9fc7 we have raised the dynamic
PS timeout to 200ms to improve user experience. Re-apply the change,
since it was reverted in the wlcore split.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-05 17:16:08 +03:00
Eliad Peller
1ab0f21262 wlcore: use the original elp time in forced_ps mode
The dynamic PS timeout is meaningless in forced PS mode.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-05 17:16:08 +03:00
Arik Nemtsov
d35dc739f6 wlcore: fix sparse warnings related to static functions
The "static" modifier was mistakenly forgotten for some functions.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-05 17:16:08 +03:00
Luciano Coelho
b5d6d9b28c wlcore/wl12xx/wl18xx: don't use TX align quirk for wl127x
Commit 4afc37 (wlcore: reorder identify_chip and get_hw_info) broke
support for wl127x chips.

When we moved the identify_chip operation to an earlier stage (ie. to
the probe function), we broke wl127x support because during HW init we
would set the WLCORE_QUIRK_TX_BLOCKSIZE_ALIGN.

To avoid this, set this quirk in the identify_chip operations and only
force it to be unset if the bus module doesn't support it.  We were
doing the opposite and setting the flag if the bus module supports it.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-05 16:07:16 +03:00
Assaf Azulay
3d62eb5a7e wl18xx: change default tcp_checksum to false
as tcp check sum is going to be removed from firmware, and as
there is a problem with getting dns in security when checksum is
enabled, it was decided to disable it by default.
for none security modes it can be enabled by module paramenter.

Signed-off-by: Assaf Azulay <assaf@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-05 15:59:41 +03:00
Luciano Coelho
c5d94169e8 wl18xx: use new fw stats structures
Some of the structures were updated, other structures had a few
missing values and a few new ones were added.  Change the driver
structs accordingly.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:59:10 +03:00
Luciano Coelho
3507efa084 wl18xx: increase tx_ba_win_size to 64
Now the firmware can support TX block ack sessions with 64 frames.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:59:06 +03:00
Luciano Coelho
5a7589be34 wlcore: increase aggregation buffer size by one page
With 4 pages (16Kb), we can't fit 10 frames in the aggregation buffer
during iperf.  This is the optimal for the firmware.  Thus, increase
the buffer size by one page.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:59:02 +03:00
Luciano Coelho
ad62d81a9e wlcore/wl12xx/wl18xx: move lower driver debugfs to a subdir
Instead of adding more files from the lower drivers into the same
directory in debugfs as wlcore, we now add a subdirectory for the
lower driver.  This makes things a bit easier, because we can quickly
see where the debugfs entry is implemented and what is specific to the
lower driver.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:58:59 +03:00
Luciano Coelho
7b03c306da wl18xx: export pwr_limit_reference_11_abg value as a module parameter
Yet another temporary module parameter requested by the firmware team.
This will be replaced by the conf binary.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:58:54 +03:00
Luciano Coelho
858403ab44 wl18xx: export low/high band component values as module params
We use hardcoded values for the different board types.  In some cases
we may need to override the defaults, so export the values as module
params.  If not defined, the defaults for the specified board type
will be used.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:58:51 +03:00
Luciano Coelho
5add82edd1 wl18xx: add power limit reference value to mac_and_phy settings
With more recent PHY firmware versions (>8.1.0.0.116), we need to use
the correct value for the pwr_limit_reference_11_abg parameter when
setting the mac_and_phy options.

For now we use a hardcoded 0xc8 as the value.  This will be moved to
the configuration binary when it gets implemented.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:58:46 +03:00
Luciano Coelho
8334271882 wl18xx: add module parameter to force SISO 20MHz
In some cases it may be useful to force narrow-band SISO channels.
Add a new value to the ht_mode module parameter to force the device to
operate in SISO 20MHz.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:58:42 +03:00
Luciano Coelho
60462b4885 wlcore: use proper values for supported local rates
We were setting all the rates bits when starting the AP role.  Instead
of doing this, we should set only the rates we really support
(eg. MIMO rates or wide-channel rates).  This commit changes that so
that we always use the default rates (basic rates + MCS0-7) and add
the values returned by the ap_get_mimo_wide_rate_mask operation.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:58:36 +03:00
Luciano Coelho
174a73034c wl18xx: don't use MIMO when ht_mode is set to wide
If the wl18xx module is loaded with ht_mode=wide (the default), we
shouldn't use MIMO rates when the channel type is not HT40.  Fix this
by checking the ht_mode before deciding which rates to used.
Additionally, set the ht_mode parameter explicitly to "wide" as the
default.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:58:32 +03:00
Luciano Coelho
06bba80e71 wlcore: print the interrupt status when recovery is triggered
In some cases it may be useful for debugging to check what is the
status of the interrupt register when a hardware recovery happens.
Print the contents of REG_INTERRUPT_NO_CLEAR (aka. HINT_STS_RAW) when
recovery starts.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:58:28 +03:00
Luciano Coelho
283e8c425f wl18xx: print the PHY firmware version from the private static data
The wl18xx firmware writes the PHY firmware version in the static
data.  Add an operation to parse the static data and print the PHY
firmware version when booting.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:58:24 +03:00
Luciano Coelho
7140df6e51 wlcore: create private static_data area and add operation to parse it
The wl18xx firmware has more information in the static_data than
wl12xx.  To be able to parse that in an abstracted way, this patch
adds a priv area to the static data struct and an operation that
allows the lower driver to parse it if necessary.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:58:20 +03:00
Luciano Coelho
8c0ea1021c wl18xx: implement fw status debugfs entries
Implement the operations that are necessary to fetch the
wl18xx-specific FW statistics and export them in debugfs.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:58:16 +03:00
Luciano Coelho
10b1e8a27a wl12xx: implement fw status debugfs entries
Implement the operations that are necessary to fetch the
wl12xx-specific FW statistics.  Re-add some of the code removed from
wlcore.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:58:12 +03:00
Luciano Coelho
bcca1bbdd4 wlcore: add debugfs macro to help print fw statistics arrays
Add a macro to make it easy to print arrays from the FW statistics
array in debugfs.  At the same time, increase the buffer size so
arrays fit more easily.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:58:08 +03:00
Luciano Coelho
4987257c30 wlcore: abstract debugfs fw_stats to be handled by the lower drivers
The FW statistics differ from hardware to hardware.  This commit
prepares for hardware-specific implementation of the FW statistics
debugfs entries.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:58:02 +03:00
Luciano Coelho
15e05bc059 wlcore: use all AP basic rates as default
Sometimes we get a BSS_CHANGED_BEACON_ENABLED event before the basic
rates have been properly set.  To avoid problems with the firmware not
expecting to receive frames at rates that are not set during
CMD_START_ROLE, we now start with all basic rates by default.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:57:58 +03:00
Luciano Coelho
62c2e579e0 wlcore: update beacon and probe_resp templates when rates change
When the data rates change, we get BSS_CHANGED_BASIC_RATES.  At this
point, we should update all the templates to match the new rates.  We
were changing some of the templates, but the beacon and the probe
response templates were missing.

[Remove redundant min_rate variable - Arik]

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:57:50 +03:00
Luciano Coelho
7ae25da396 wl18xx: disable MCS_13 for wl18xx PG 1.0
There are some problems with MCS_13 in PG 1.0 hardware.  So we disable
it when PG 1.0 is detected.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:57:45 +03:00
Luciano Coelho
4afc37a0c1 wlcore: reorder identify_chip and get_hw_info
We can do get the HW information and identify the chip already at
probe time.  This makes it easier to mangle with the parameters during
identify chip before registering the hardware with mac80211.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:57:41 +03:00
Luciano Coelho
73d8a42464 wl18xx: change low_band_component_type value for COM8
Like HDK, COM8 uses 0x06 for the low_band_component_type as well.
Hardcode the value for COM8 until this configuration can be done in
the external configuration binary (to be implemented).

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:57:36 +03:00
Luciano Coelho
4f64a1e93f wlcore: add space for private area when allocating fw_status
When allocating the fw_status structure, the space for the
lower-driver private area was missing.  This was causing an illegal
write outside the allocated area, which was causing random oopses
around the kernel.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:57:32 +03:00
Luciano Coelho
4b9d2365d5 wl18xx: changed default board_type to HDK
Since the most common board we're using now is an HDK board, change
the default board_type to hdk.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:57:27 +03:00
Luciano Coelho
776f030aa0 wl18xx: copy the default configuration before checking the board_type
We were changing the low_band_component_type in the private
configuration structure before copying the default values to it, so
the change was overwritten and only took effect after HW recovery.

Reported-by: Dror Erez <drorer@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:57:20 +03:00
Luciano Coelho
df472894ab wlcore: add module parameter to dump SDIO reads and writes
In some cases we may want to dump all the SDIO data in order to get
detailed information for debugging the communication with the
firmware.

Add printks to dump the data and a module parameter to enable/disable
it.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:57:15 +03:00
Luciano Coelho
1ddbc7d4c7 wl18xx: add a module parameter to control 11a support
In wl18xx we don't have an NVS yet, so we need to control whether 11a
is supported with a module parameter for now.  11a support is enabled
by default and can be changed by setting enable_11a to false when
loading the module.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:57:11 +03:00
Luciano Coelho
a5114d9c0d wl18xx: derive the MAC address from the BD_ADDR in fuse ROM
Add the get_mac operation in order to fetch the BD_ADDR from fuse ROM,
so that we can derive the WLAN MAC addresses from it.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:57:06 +03:00
Arik Nemtsov
0afd04e5e5 wlcore/wl12xx/18xx: split fw_status struct into two
The number of RX packet descriptors may vary from chip to chip and
in different firmware versions.  Unfortunately, the array that
contains the actual descriptors is in the middle of the fw_status
structure.  To manage this, we split the struct into two so we can
calculate the offset of what comes after the array and access the last
elements more easily.

[Changed the STATUS_LEN macro to be placement agnostic - Arik]

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:56:58 +03:00
Luciano Coelho
102165c6d2 wl18xx: add module parameter to disable TCP checksum
Add a new module parameter to disable TCP checksum offload.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:56:53 +03:00
Luciano Coelho
e9258815a8 wl18xx: add number of antennas and dc2dc type as module params
We need to specify the number of 2.4GHz and 5GHz antennas and whether
the board has an internal or external DC2DC.  Add some module
parameters that allow changing that.

In the future this will come from the "NVS" file.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:56:48 +03:00
Luciano Coelho
0a1569f82b wl18xx: change the low_band_component_type for HDK boards
Currently, all HDK boards use low_band_component_type 0x06.  In the
future this may change, but for now, we hardcode this value when the
board_type is set to HDK.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:56:43 +03:00
Luciano Coelho
be42aee6df wl18xx: add plt_init operation
Add the correct FW name for PLT (which is the same as the normal
firmware) and implement the plt_init operation.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:56:39 +03:00
Luciano Coelho
c331b344d5 wlcore/wl12xx: add plt_init op and move the code to wl12xx
PLT mode needs to be initialized differently for each chip.  This
patch adds an operation to init PLT and moves the existing PLT
initialization into the wl12xx driver.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-06-05 15:56:33 +03:00
Arik Nemtsov
05057c0621 wl18xx: change board type enum according to new FW
Add more board types and remove a now unneeded write to SCR_PAD2 setting
the board type.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-05 15:56:31 +03:00
Arik Nemtsov
2f1d74e6e7 wl18xx: don't upload NVS to FW
In this chip family the NVS file should not be uploaded to FW. In fact,
we encounter strange bugs (sdio errors) when trying to upload it with
certain parameters.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-05 15:56:29 +03:00
Arik Nemtsov
f2baf075c5 wl18xx: init Tx-released index to 0 on HW init
This ensures the index is 0 on FW recovery and prevents spurious error
prints - "WARNING illegal id in tx completion".

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-05 15:56:27 +03:00