Replace the chip lock by a the controller lock. For simple drivers a
dummy controller structure is created by the scan code.
This simplifies the locking algorithm in nand_get/release_chip().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Unrolling the loops produces denser and much faster code.
Add a config switch which allows to select the byte order of the
resulting ecc code. The current Linux implementation has a byte
swap versus the SmartMedia specification
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The patch below adds support for the NAND device on the Amstrad Delta.
This is a 32MiB 8bit Toshiba device, with the data bus connected to the
OMAP MPUIO pins and ALE, CLE, NCE, NRE, NWE and NWP all connected to the
Delta's latch2 16bit latch.
Signed-Off-By: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
On AMD Au1550 the static bus controller fails to keep -CE asserted during
chip ready delay on read commands and the NAND chip being used requires this.
So, the current driver allows nand_base.c to drive -CE manually during the
entire sector read. When the PCMCIA driver is enabled however, occasionally
the ECC errors occur on NAND reads. This happens because the PCMCIA driver
polls sockets periodically and reads one of the board's control/status regs
(BCSRs) which are on the same static bus as the NAND flash, and just use
another chip select (and the NOR flash also resides on that bus), so as the
NAND driver forces NAND chip select asserted and the -RE signal is shared, a
contention occurs on the static bus when BCSR or NOR flash is read while we're
reading from NAND.
So, we either can't keep interrupts enabled during the whole NAND sector
read (which is hardly acceptable), or have to implement some interlocking
scheme between multiple drivers (which is painful, and makes me shudder :-).
There's a third way which has proven to work: to force -CE asserted only
while we're waiting for a NAND chip to become ready after a read command,
disabling interrupts for a maximum of 25 microseconds (according to Toshiba
TC58DVM92A1FT00 datasheet -- this chip is mentioned in the board schematics);
for Samsung NAND chip which seems to be actually used this delay is even less,
12 us.
Signed-off-by: Konstantin Baydarov <kbaidarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
During the last cleanup of the AMD Au1550 NAND driver the old buglet was
reintroduced: as the MEM_STNDCTL register is write-only and seem to always
read as 0x31, read-modify-write to it done in au1xxx_nand_init() will have the
side effect of enabling -RCS0/1 pin override (via bits 4/5 of this reg.), thus
possibly causing a contention on the static bus when the NOR flash (using
-RCS0) or board control status registers (using -RCS2) are read. Luckily, this
goes away with a first NAND access, since au1550_hwcontrol() doesn't try to
read this register before writing anymore.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We all inherited the same error from the original NAND board driver which
got copied and changed. Fix them all at once...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Make it work even with compilers which lack the wit to notice that
THIS_MODULE is always non-NULL. Use #ifdef MODULE instead. It's only
a temporary debugging check anyway.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The _board_ driver needs to be mtd->owner, and it in turn pins the
nand.ko module. Fix them all to actually do that, and fix nand.ko not to
overwrite it -- and also to check that the caller sets it, if the caller
is a module.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We were scanning for 0xFF through the entire chip -- which takes a while
when it's a 512MiB device as I have on my current toy. The specs only say
we need to check certain bytes -- so do only that.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
- Implement HW ECC support,
- Provide read_buf() and write_buf() routines using memcpy
- Use on-flash bad block table
- Fix module refcounting
- Avoid read/modify/write in hwcontrol()
- Minor cosmetic fixes
Partly based on code and ideas from Tom Sylla <tom.sylla@amd.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This lacks hardware ECC support and a few optimisations we're going to
want fairly soon, but it works well enough to mount and use JFFS2.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The TS-72xx is a series of embedded single board computers from
Technologic Systems based on the Cirrus ep93xx (arm920t based) CPU.
The TS-7200 uses NOR flash, while all the other models in the series
(TS-7250, TS-7260) use NAND flash -- included is a driver for the NAND
flash on those boards.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove
duplicates of the macro.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MTD_NAND=m and MTD_NAND_SHARPSL=y or MTD_NAND_NANDSIM=y are illegal
combinations that mustn't be allowed.
This patch fixes this bug by making MTD_NAND_SHARPSL and MTD_NAND_NANDSIM
tristate's.
Additionally, it fixes some whitespace damage at these options.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: "Artem B. Bityutskiy" <dedekind@yandex.ru>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ICC likes to complain about storage class not being first, GCC doesn't
care much (except for cases like "inline static").
have a hard time seeing how it could break anything.
Thanks to Gabriel A. Devenyi for pointing out
http://linuxicc.sourceforge.net/ which is what made me create this patch.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It seems that clk_use() and clk_unuse() are additional complexity
which isn't required anymore. Remove them from the clock framework
to avoid the additional confusion which they cause, and update all
ARM machine types except for OMAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch contains the following possible cleanups:
- every file should #include the headers containing the prototypes for
it's global functions
- make needlessly global functions static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
__ioremap is an architecture private interface and must not be used
by drivers when the architecture independent interface will do just
as well. Switch the ipaq drivers to use the correct interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes almost all inclusions of linux/version.h. The 3
#defines are unused in most of the touched files.
A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.
There are also lots of #ifdef for long obsolete kernels, this was not
touched. In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.
quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`
search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the drivers/mtd part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/mtd/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Joern Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nathan Roberts noticed the nand_write_ecc index into oobbuf goes out of
bounds when crossing an erase block boundary, causing incorrect OOB data
to be written and corrupting memory. Reset the index to zero after
re-preparing oobbuf for a new erase block.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In case of an odd offset, the result was shifted by 1 instead of 8
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The Sharp Zaurus akita and borzoi models are large page flash devices.
This patch adds support for them to the sharpsl MTD NAND driver but
keeps the oob layout and bad block positions compatible with the Sharp
Zaurus 2.4 kernel and ROM bootloader.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added owner fields to the device_driver for tracking
ownership when built as a module
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- cleaned up the partitions and include files
- added more flexible CS and address detection and setup
Regression tested on db1200 and db1550.
Signed-off-by: Pete Popov <ppopov@pacbell.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The changes introduced allow to suspend/resume NAND flash.
A new state (FL_PM_SUSPENDED) is introduced, as well as
routines for mtd->suspend and mtd->resume to put the flash in
suspended state from software pov.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The bit mask used for oob size calculation was using 2 bits instead
of one. Fortunately the next bit has been 0 all the time.
Thanks to Nathan H. for pointing this out
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
It's pointless to include mach-types.h if you're not going to use
anything from it. These references were removed as a result of:
grep -lr 'asm/mach-types\.h' . | xargs grep -L 'machine_is_\|MACH_TYPE_\|MACHINE_START\|machine_type'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
