When in an active transaction that takes a signal, we need to be careful with
the stack. It's possible that the stack has moved back up after the tbegin.
The obvious case here is when the tbegin is called inside a function that
returns before a tend. In this case, the stack is part of the checkpointed
transactional memory state. If we write over this non transactionally or in
suspend, we are in trouble because if we get a tm abort, the program counter
and stack pointer will be back at the tbegin but our in memory stack won't be
valid anymore.
To avoid this, when taking a signal in an active transaction, we need to use
the stack pointer from the checkpointed state, rather than the speculated
state. This ensures that the signal context (written tm suspended) will be
written below the stack required for the rollback. The transaction is aborted
becuase of the treclaim, so any memory written between the tbegin and the
signal will be rolled back anyway.
For signals taken in non-TM or suspended mode, we use the
normal/non-checkpointed stack pointer.
Tested with 64 and 32 bit signals
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # v3.9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These cause codes are usable by userspace, so let's export to uapi.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # v3.9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we are emulating an instruction inside an active user transaction that
touches memory, the kernel can't emulate it as it operates in transactional
suspend context. We need to abort these transactions and send them back to
userspace for the hardware to rollback.
We can service these if the user transaction is in suspend mode, since the
kernel will operate in the same suspend context.
This adds a check to all alignment faults and to specific instruction
emulations (only string instructions for now). If the user process is in an
active (non-suspended) transaction, we abort the transaction go back to
userspace allowing the HW to roll back the transaction and tell the user of the
failure. This also adds new tm abort cause codes to report the reason of the
persistent error to the user.
Crappy test case here http://neuling.org/devel/junkcode/aligntm.c
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # v3.9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PAPR carves out 0xff-0xe0 for hypervisor use of transactional memory software
abort cause codes. Unfortunately we don't respect this currently.
Below fixes this to move our cause codes to below this region.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # 3.9 only
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc fixes from Benjamin Herrenschmidt:
"Some more P8 related bits, a bunch of fixes for our P7+/P8 HW crypto
drivers, some added workarounds for those radeons that don't do proper
64-bit MSIs and a couple of other trivialities by myself."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pseries: Make 32-bit MSI quirk work on systems lacking firmware support
powerpc/powernv: Build a zImage.epapr
powerpc: Make radeon 32-bit MSI quirk work on powernv
powerpc: Context switch more PMU related SPRs
powerpc/powernv: Fix condition for when to invalidate the TCE cache
powerpc/pci: Fix bogus message at boot about empty memory resources
powerpc: Fix TLB cleanup at boot on POWER8
drivers/crypto/nx: Fixes for multiple races and issues
Recent commit e61133dda4 added support
for a new firmware feature to force an adapter to use 32 bit MSIs.
However, this firmware is not available for all systems. The hack below
allows devices needing 32 bit MSIs to work on these systems as well.
It is careful to only enable this on Gen2 slots, which should limit
this to configurations where this hack is needed and tested to work.
[Small change to factor out the hack into a separate function -- BenH]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The zImage.epapr wrapper allows to use zImages when booting via a flat
device-tree which can be used on powernv.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This moves the quirk itself to pci_64.c as to get built on all ppc64
platforms (the only ones with a pci_dn), factors the two implementations
of get_pdn() into a single pci_get_dn() and use the quirk to do 32-bit
MSIs on IODA based powernv platforms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In commit 9353374 "Context switch the new EBB SPRs" we added support for
context switching some new EBB SPRs. However despite four of us signing
off on that patch we missed some. To be fair these are not actually new
SPRs, but they are now potentially user accessible so need to be context
switched.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We use two flags, one to indicate an invalidation is needed after
creating a new entry and one to indicate an invalidation is needed
after removing an entry. However we were testing the wrong flag
in the remove case.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The message is only meant to be displayed if resource 0 is empty,
but was displayed if any is.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The TLB has 512 congruence classes (2048 entries 4 way set associative)
while P7 had 128
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Here are a number of tiny USB bugfixes / new device ids for 3.10-rc2
The majority of these are USB gadget fixes, but they are all small.
Other than that, some USB host controller fixes, and USB serial driver
fixes for problems reported with them.
Also hopefully a fixed up USB_OTG Kconfig dependancy, that one seems to
be almost impossible to get right for all of the different platforms
these days.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlGeP/gACgkQMUfUDdst+ykXygCfeIL5/HMREhUSHQgb6IiIDR81
QHAAn0zJfRAyWUz4AtbrRsLSVfk3Q9vm
=DQIq
-----END PGP SIGNATURE-----
Merge tag 'usb-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of tiny USB bugfixes / new device ids for 3.10-rc2
The majority of these are USB gadget fixes, but they are all small.
Other than that, some USB host controller fixes, and USB serial driver
fixes for problems reported with them.
Also hopefully a fixed up USB_OTG Kconfig dependancy, that one seems
to be almost impossible to get right for all of the different
platforms these days."
* tag 'usb-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (56 commits)
USB: cxacru: potential underflow in cxacru_cm_get_array()
USB: ftdi_sio: Add support for Newport CONEX motor drivers
USB: option: add device IDs for Dell 5804 (Novatel E371) WWAN card
usb: ohci: fix goto wrong tag in err case
usb: isp1760-if: fix memleak when platform_get_resource fail
usb: ehci-s5p: fix memleak when fallback to pdata
USB: serial: clean up chars_in_buffer
USB: ti_usb_3410_5052: fix chars_in_buffer overhead
USB: io_ti: fix chars_in_buffer overhead
USB: ftdi_sio: fix chars_in_buffer overhead
USB: ftdi_sio: clean up get_modem_status
USB: serial: add generic wait_until_sent implementation
USB: serial: add wait_until_sent operation
USB: set device dma_mask without reference to global data
USB: Blacklisted Cinterion's PLxx WWAN Interface
usb: option: Add Telewell TW-LTE 4G
USB: EHCI: remove bogus #error
USB: reset resume quirk needed by a hub
USB: usb-stor: realtek_cr: Fix compile error
usb, chipidea: fix link error when USB_EHCI_HCD is a module
...
Commit 84ebc10294 (USB: remove
CONFIG_USB_SUSPEND option) failed to remove all of the usages of
USB_SUSPEND throughout the kernel. This patch (as1677) removes the
remaining instances of that symbol.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull powerpc fixes from Benjamin Herrenschmidt:
"This is mostly bug fixes (some of them regressions, some of them I
deemed worth merging now) along with some patches from Li Zhong
hooking up the new context tracking stuff (for the new full NO_HZ)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (25 commits)
powerpc: Set show_unhandled_signals to 1 by default
powerpc/perf: Fix setting of "to" addresses for BHRB
powerpc/pmu: Fix order of interpreting BHRB target entries
powerpc/perf: Move BHRB code into CONFIG_PPC64 region
powerpc: select HAVE_CONTEXT_TRACKING for pSeries
powerpc: Use the new schedule_user API on userspace preemption
powerpc: Exit user context on notify resume
powerpc: Exception hooks for context tracking subsystem
powerpc: Syscall hooks for context tracking subsystem
powerpc/booke64: Fix kernel hangs at kernel_dbg_exc
powerpc: Fix irq_set_affinity() return values
powerpc: Provide __bswapdi2
powerpc/powernv: Fix starting of secondary CPUs on OPALv2 and v3
powerpc/powernv: Detect OPAL v3 API version
powerpc: Fix MAX_STACK_TRACE_ENTRIES too low warning again
powerpc: Make CONFIG_RTAS_PROC depend on CONFIG_PROC_FS
powerpc: Bring all threads online prior to migration/hibernation
powerpc/rtas_flash: Fix validate_flash buffer overflow issue
powerpc/kexec: Fix kexec when using VMX optimised memcpy
powerpc: Fix build errors STRICT_MM_TYPECHECKS
...
Currently we only set the "to" address in the branch stack when the CPU
explicitly gives us a value. Unfortunately it only does this for XL form
branches (eg blr, bctr, bctar) and not I and B form branches (eg b, bc).
Fortunately if we read the instruction from memory we can extract the offset of
a branch and calculate the target address.
This adds a function power_pmu_bhrb_to() to calculate the target/to address of
the corresponding I and B form branches. It handles branches in both user and
kernel spaces. It also plumbs this into the perf brhb reading code.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current Branch History Rolling Buffer (BHRB) code misinterprets the order
of entries in the hardware buffer. It assumes that a branch target address
will be read _after_ its corresponding branch. In reality the branch target
comes before (lower mfbhrb entry) it's corresponding branch.
This is a rewrite of the code to take this into account.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The new Branch History Rolling buffer (BHRB) code is only useful on 64bit
processors, so move it into the #ifdef CONFIG_PPC64 region.
This avoids code bloat on 32bit systems.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Start context tracking support from pSeries.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch corresponds to
[PATCH] x86: Use the new schedule_user API on userspace preemption
commit 0430499ce9
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch allows RCU usage in do_notify_resume, e.g. signal handling.
It corresponds to
[PATCH] x86: Exit RCU extended QS on notify resume
commit edf55fda35
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is the exception hooks for context tracking subsystem, including
data access, program check, single step, instruction breakpoint, machine check,
alignment, fp unavailable, altivec assist, unknown exception, whose handlers
might use RCU.
This patch corresponds to
[PATCH] x86: Exception hooks for userspace RCU extended QS
commit 6ba3c97a38
But after the exception handling moved to generic code, and some changes in
following two commits:
56dd9470d7
context_tracking: Move exception handling to generic code
6c1e0256fa
context_tracking: Restore correct previous context state on exception exit
it is able for exception hooks to use the generic code above instead of a
redundant arch implementation.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is the syscall slow path hooks for context tracking subsystem,
corresponding to
[PATCH] x86: Syscall hooks for userspace RCU extended QS
commit bf5a3c13b9
TIF_MEMDIE is moved to the second 16-bits (with value 17), as it seems there
is no asm code using it. TIF_NOHZ is added to _TIF_SYCALL_T_OR_A, so it is
better for it to be in the same 16 bits with others in the group, so in the
asm code, andi. with this group could work.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
MSR_DE is not cleared on entry to the kernel, and we don't clear it
explicitly outside of debug code. If we have MSR_DE set in
prime_debug_regs(), and the new thread has events enabled in DBCR0
(e.g. ICMP is set in thread->dbsr0, even though it was cleared in the
real DBCR0 when the thread got scheduled out), we'll end up taking a
debug exception in the kernel when DBCR0 is loaded. DSRR0 will not
point to an exception vector, and the kernel ends up hanging at
kernel_dbg_exc. Fix this by always clearing MSR_DE when we load new
debug state.
Another observed source of kernel_dbg_exc hangs is with the branch
taken event. If this event is active, but we take a non-debug trap
(e.g. a TLB miss or an asynchronous interrupt) before the next branch.
We end up taking a branch-taken debug exception on the initial branch
instruction of the exception vector, but because the debug exception is
DBSR_BT rather than DBSR_IC we branch to kernel_dbg_exc before even
checking the DSRR0 address. Fix this by checking for DBSR_BT as well
as DBSR_IC, which is what 32-bit does and what the comments suggest was
intended in the 64-bit code as well.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some versions of GCC apparently expect this to be provided by libgcc.
Updates from Mikey to fix 32 bit version and adding "r" to registers.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current code fails to handle kexec on OPALv2. This fixes it
and adds code to improve the situation on OPALv3 where we can
query the CPU status from the firmware and decide what to do
based on that.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Saw this warning again, and this time from the ret_from_fork path.
It seems we could clear the back chain earlier in copy_thread(), which
could cover both path, and also fix potential lockdep usage in
schedule_tail(), or exception occurred before we clear the back chain.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are getting build errors with CONFIG_PROC_FS=n:
arch/powerpc/kernel/rtas_flash.c
In function 'rtas_flash_init':
745:33: error: unused variable 'f' [-Werror=unused-variable]
But rtas_flash.c should not be built when CONFIG_PROC_FS=n, beacause all
it does is provide a /proc interface to the RTAS flash routines.
CONFIG_RTAS_FLASH already depends on CONFIG_RTAS_PROC, to indicate that
it depends on the RTAS proc support, but CONFIG_RTAS_PROC does not
depend on CONFIG_PROC_FS. So fix that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch brings online all threads which are present but not online
prior to migration/hibernation. After migration/hibernation those
threads are taken back offline.
During migration/hibernation all online CPUs must call H_JOIN, this is
required by the hypervisor. Without this patch, threads that are offline
(H_CEDE'd) will not be woken to make the H_JOIN call and the OS will be
deadlocked (all threads either JOIN'd or CEDE'd).
Cc: <stable@kernel.org>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit b3f271e86e (powerpc: POWER7 optimised memcpy using VMX and
enhanced prefetch) uses VMX when it is safe to do so (ie not in
interrupt). It also looks at the task struct to decide if we have to
save the current tasks' VMX state.
kexec calls memcpy() at a point where the task struct may have been
overwritten by the new kexec segments. If it has been overwritten
then when memcpy -> enable_altivec looks up current->thread.regs->msr
we get a cryptic oops or lockup.
I also notice we aren't initialising thread_info->cpu, which means
smp_processor_id is broken. Fix that too.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@vger.kernel.org> # 3.6+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Our pgtable are 2*sizeof(pte_t)*PTRS_PER_PTE which is PTE_FRAG_SIZE.
Instead of depending on frag size, mask with PMD_MASKED_BITS.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull audit changes from Eric Paris:
"Al used to send pull requests every couple of years but he told me to
just start pushing them to you directly.
Our touching outside of core audit code is pretty straight forward. A
couple of interface changes which hit net/. A simple argument bug
calling audit functions in namei.c and the removal of some assembly
branch prediction code on ppc"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: fix message spacing printing auid
Revert "audit: move kaudit thread start from auditd registration to kaudit init"
audit: vfs: fix audit_inode call in O_CREAT case of do_last
audit: Make testing for a valid loginuid explicit.
audit: fix event coverage of AUDIT_ANOM_LINK
audit: use spin_lock in audit_receive_msg to process tty logging
audit: do not needlessly take a lock in tty_audit_exit
audit: do not needlessly take a spinlock in copy_signal
audit: add an option to control logging of passwords with pam_tty_audit
audit: use spin_lock_irqsave/restore in audit tty code
helper for some session id stuff
audit: use a consistent audit helper to log lsm information
audit: push loginuid and sessionid processing down
audit: stop pushing loginid, uid, sessionid as arguments
audit: remove the old depricated kernel interface
audit: make validity checking generic
audit: allow checking the type of audit message in the user filter
audit: fix build break when AUDIT_DEBUG == 2
audit: remove duplicate export of audit_enabled
Audit: do not print error when LSMs disabled
...
Pull stray syscall bits from Al Viro:
"Several syscall-related commits that were missing from the original"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
switch compat_sys_sysctl to COMPAT_SYSCALL_DEFINE
unicore32: just use mmap_pgoff()...
unify compat fanotify_mark(2), switch to COMPAT_SYSCALL_DEFINE
x86, vm86: fix VM86 syscalls: use SYSCALL_DEFINEx(...)
lockdep.c has this:
/*
* So we're supposed to get called after you mask local IRQs,
* but for some reason the hardware doesn't quite think you did
* a proper job.
*/
if (DEBUG_LOCKS_WARN_ON(!irqs_disabled()))
return;
Since irqs_disabled() is based on soft_enabled(), that (not just the
hard EE bit) needs to be 0 before we call trace_hardirqs_off.
Signed-off-by: Scott Wood <scottwood@freescale.com>
We add a machine_shutdown hook that frees the OPAL interrupts
(so they get masked at the source and don't fire while kexec'ing)
and which triggers an IODA reset on all the PCIe host bridges
which will have the effect of blocking all DMAs and subsequent
PCIs interrupts.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRifUnAAoJEEFnBt12D9kBs2YP/0U6+ia+xYvkVaJc28PDVIzn
OReZNcJOYU8D5voxz0voaRD0EdcPwjbMu9Kp9aXMHlk4VxevF+8jCc/us0bIjtO1
VcB5VmSCIhMhxdnBlum11Mk7Vr5MCweyl9NBsypnPt8cl4obMBZHf2yzoodFktNb
wtyYlOb6FALtc6iDbOO6dG3w9F7FAOLvskUFzdv89m8mupTsBu9jw9NqFDbJHOex
rxq0Sdd+kWF/nkJVcV5Y6jIdletRlhpipefMJ9diexreHvwqh+c4kJEYZaXgB5+m
ha95cPbReK1d+RqzM3A8d4irzSVSmq4k7ijI6QkFOr48+AH7XsgKv5so885LKzMN
IIXg2Phm9i0H8+ecEvhcc4oIYBHJiEKK54Y0qUD9dqbFoDGPTCSqMHdSSMbpAY+J
bIIXlVzj1En3PPNUJLPt8q8Qz6WxCT9mDST3QSGYnD4o90HT+1R9j92RxGL6McOq
rUOyJDwmzFvpBvKK4raGdOU435M+ps2NPKKNIRaIGQPPY9rM1kN4YqvhXukEsC9L
3a3+3cQLh7iKxBHncxeQsJfethP1CPkJnzvF9r+ZZLf2rcPH4pbQIE2uO0XnX/nd
5/DKi0nGgAJ//GMMzdo3RiOA5zGFjIZ/KMvfhQldpP6qFJRhqdGi6FPlAcwr1z1n
YnCByPwwlvfC4LTXFOGL
=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
If the firmware returns an error such as "closed" (or hardware
error), we should drop characters.
Currently we only do that when a firmware compatible with OPAL v2
APIs is detected, in the code that calls opal_console_write_buffer_space(),
which didn't exist with OPAL v1 (or didn't work).
However, when enabling early debug consoles, the flag indicating
that v2 is supported isn't set yet, causing us, in case of errors
or closed console, to spin forever.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a new udbg early debug console which utilises
statically defined input and output buffers stored within the kernel
BSS. It is primarily designed to assist with bring up of new hardware
which may not have a working console but which has a method of
reading/writing kernel memory.
This version incorporates comments made by Ben H (thanks!).
Changes from v1:
- Add memory barriers.
- Ensure updating of read/write positions is atomic.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If hard_irq_disable() is called while interrupts are already soft-disabled
(which is the most common case) all is already well.
However you can (and in some cases want) to call it while everything is
enabled (to make sure you don't get a lazy even, for example before entry
into KVM guests) and in this case we need to inform the irq tracer that
the irqs are going off.
We have to change the inline into a macro to avoid an include circular
dependency hell hole.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are registering the attribute with permission 0600 but it
doesn't have a store callback, which causes WARN_ON's during
boot. Fix the permission.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PCI core supports an offset per aperture nowadays but our arch
code still has a single offset per host bridge representing the
difference betwen CPU memory addresses and PCI MMIO addresses.
This is a problem as new machines and hypervisor versions are
coming out where the 64-bit windows will have a different offset
(basically mapped 1:1) from the 32-bit windows.
This fixes it by using separate offsets. In the long run, we probably
want to get rid of that intermediary struct pci_controller and have
those directly stored into the pci_host_bridge as they are parsed
but this will be a more invasive change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some devices don't have a correct node ID and thus can't be
attached to an iommu.
The message displayed by the iommu code isn't very useful if
you don't have a device-tree node as it tries to print the
device-tree path but not the struct device name.
Improve this by printing the device name as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are registering the attribute with permission 0644 but it
doesn't have a store callback, which causes WARN_ON's during
boot. Fix the permission.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some interrupt controllers refuse to map interrupts marked as
"protected" by firwmare. Since we try to map everyting in the
device-tree on some platforms, we end up with a lot of nasty
WARN's in the boot log for what is a normal situation on those
machines.
This defines a specific return code (-EPERM) from the host map()
callback which cause irqdomain to fail silently.
MPIC is updated to return this when hitting a protected source
printing only a single line message for diagnostic purposes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>