This migrates SH7786 to evt2irq() backed hwirq lookup rather than
using an open-coded calculation. This will make it possible to reposition
the vector base at a later point in time.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The generic hardirq layer provides all of the routines that we need these
days, so we don't require any of the dynamic IRQ API wrapping, and can
call in to irq_alloc_descs() directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SSR.MD status amongst other things are already made available, which
can be used for encoding a more precise fault code value.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This unifies the fast-path TLB miss handler, allowing for further cleanup
and eventual utilization of a shared _32/_64 handler.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the fast-path handler has been moved, we also need to update the
Makefile to ensure that the same restrictions for caller-save registers
are observed.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This brings the sh64 version in line with the sh32 one with regards to
how errors are handled. Base work for further unification of the
implementations.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that we have a method for finding out if we're handling an ITLB fault
or not without passing it all the way down the chain, it's possible to
use the __update_tlb() interface in place of a special __do_tlb_refill().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves the now generic _32 page fault handling code to a shared place
and adapts the _64 implementation to make use of it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was reworked some time ago to go through fixmaps instead, leaving
the range itself unused. As such, kill off the remaining references and
hand over the remaining space for fixmaps directly. This also makes it
possible to simplify the vmalloc fault case as we no longer have to care
about the special section.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
At the moment the top of the fixmap space is calculated from P4SEG, which
places it at the end of the store queue space when that API is enabled.
Make sure we use P3_ADDR_MAX here instead to find the proper address
limit. With this done, it's also possible to switch to the generic
vmalloc address range check now that VMALLOC_START/END encapsulate the
translatable areas that we care about.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a simple interface modelled after sparc64/m32r to encode
the error code in the upper byte of thread_info for finer-grained
handling in the page fault path.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the x86 changes for tidying up the page fault error paths.
We'll build on top of this for _32/_64 unification.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rather than requiring architectures that use gpiolib but don't have any
need to define anything custom to copy an asm/gpio.h provide a Kconfig
symbol which architectures must select in order to include gpio.h and
for other architectures just provide the trivial implementation directly.
This makes it much easier to do gpiolib updates and is also a step towards
making gpiolib APIs available on every architecture.
For architectures with existing boilerplate code leave a stub header in
place which warns on direct inclusion of asm/gpio.h and includes
linux/gpio.h to catch code that's doing this. Direct inclusion of
asm/gpio.h has long been deprecated.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jonas Bonn <jonas@southpole.se>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The RSK2+SH7269 board uses the SH7269 processor. It is often
referred to as just rsk7269. NOR Flash, SDRAM, serial, USB Host and
ethernet are working.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is an sh2a device (max 266MHz) with FPU, video display
controller (VDC), 8 serial ports, 4 I2C channels, 3 CAN ports,
SD and on-chip USB.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Too many drivers fail at IOPORT vs IOMEM checking before blindly calling
in to the API, so we may as well just provide basic stubs to get more
build coverage. Other platforms already do this, too (tile, parisc, etc.)
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The RSK2+SH7264 board uses the sh7264 processor. It is often
referred to as just rsk7264. NOR Flash, SDRAM, serial, USB Host and
ethernet are working.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is an sh2a device with FPU, video display controller (VDC),
8 serial ports, 3 I2C channels, 2 CAN ports, SD and on-chip USB.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the introduction of static keys, anything using tracepoints blows up
in the following manner:
include/trace/events/oom.h:8:13: error: initializer element is not constant
include/trace/events/oom.h:8:13: error: (near initialization for '__tracepoint_oom_score_adj_update')
include/trace/events/oom.h:8:13: error: initializer element is not constant
include/trace/events/oom.h:8:13: error: (near initialization for '__tracepoint_oom_score_adj_update.key')
This is a result of the STATIC_KEY_INIT_xxx defs wrapping ATOMIC_INIT()
which on sh includes an atomic_t typecast. Given that we don't really
need the typecast for anything anymore, the simplest solution is simply
to kill off the cast.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
