Remove rsstable array and its initialization from be_set_rss_hash_opts().
The array became unused after "e255787 be2net: Support for configurable
RSS hash key". The initial RSS table is now filled and stored for later
usage during Rx queue creation.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX/TX interrupt for Network Control queue and Best Effort queue
is issued at the same time, the interrupt mask of Network Control
queue will be reset when the mask of Best Effort queue is set.
This patch fixes this problem.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
On certain hardware after software reboot the chip may get stuck and fail
to reinitialize during reset. This can be fixed by ensuring that PHY is
reset too.
Old PHY resetting method required operational MDIO interface, therefore
the chip should have been already set up. In order to be able to function
during probe, it is changed to use PMT_CTRL register.
The problem could be observed on SMDK5410 board.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The err variable wasn't set with the correct error value in some cases.
Fixes: 47605df953 ('mlx4: Modify proxy/tunnel QP mechanism [..]')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cleaning slave's counter resources, we hold a spinlock that
protects the slave's counters list. As part of the clean, we call
__mlx4_clear_if_stat which calls mlx4_alloc_cmd_mailbox which is a
sleepable function.
In order to fix this issue, hold the spinlock, and copy all counter
indices into a temporary array, and release the spinlock. Afterwards,
iterate over this array and free every counter. Repeat this scenario
until the original list is empty (a new counter might have been added
while releasing the counters from the temporary array).
Fixes: b72ca7e96a ("net/mlx4_core: Reset counters data when freed")
Reported-by: Moni Shoua <monis@mellanox.com>
Tested-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On xmit path we use skb_frag_dma_map() which is using dma_map_page(),
while upon completion we dma-unmap the skb fragments using
dma_unmap_single() rather than dma_unmap_page().
To fix this, we now save the dma map type on xmit path and use this
info to call the right dma unmap method upon TX completion.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On change mtu the driver compares between hardware queried mtu and
software requested mtu. We need to compare between software
representation of the queried mtu and the requested mtu.
Fixes: facc9699f0 ('net/mlx5e: Fix HW MTU settings')
Signed-off-by: Doron Tsur <doront@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent outgoing multicast frames from looping back to the RX queue.
By introducing new HW capability self_lb_en_modifiable, which indicates
the support to modify self_lb_en bit in modify_tir command.
When this capability is set we can prevent TIRs from sending back
loopback multicast traffic to their own RQs, by "refreshing TIRs" with
modify_tir command, on every time new channels (SQs/RQs) are created at
device open.
This is needed since TIRs are static and only allocated once on driver
load, and the loopback decision is under their responsibility.
Fixes issues of the kind:
"IPv6: eth2: IPv6 duplicate address fe80::e61d:2dff:fe5c:f2e9 detected!"
The issue is seen since the IPv6 solicitations multicast messages are
loopedback and the network stack thinks they are coming from another host.
Fixes: 5c50368f38 ("net/mlx5e: Light-weight netdev open/stop")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5e_get_inline_hdr_size didn't take into account the vlan insertion
into the inline WQE segment.
This could lead to max inline violation in cases where
skb_headlen(skb) + VLAN_HLEN >= sq->max_inline.
Fixes: 3ea4891db8 ("net/mlx5e: Fix LSO vlan insertion")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If device probe fails, driver remains bound to the PCI device. However,
driver data has been reset to NULL. This causes crash upon dereferencing
it in nicvf_remove()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building dwmac-ipq806x on a 64-bit architecture produces a harmless
warning from gcc:
stmmac/dwmac-ipq806x.c: In function 'ipq806x_gmac_probe':
include/linux/bitops.h:6:19: warning: overflow in implicit constant conversion [-Woverflow]
val = QSGMII_PHY_CDR_EN |
stmmac/dwmac-ipq806x.c:333:8: note: in expansion of macro 'QSGMII_PHY_CDR_EN'
#define QSGMII_PHY_CDR_EN BIT(0)
#define BIT(nr) (1UL << (nr))
This is a result of the type conversion rules in C, when we take the
logical OR of multiple different types. In particular, we have
and unsigned long
QSGMII_PHY_CDR_EN == BIT(0) == (1ul << 0) == 0x0000000000000001ul
and a signed int
0xC << QSGMII_PHY_TX_DRV_AMP_OFFSET == 0xc0000000
which together gives a signed long value
0xffffffffc0000001l
and when this is passed into a function that takes an unsigned int type,
gcc warns about the signed overflow and the loss of the upper 32-bits that
are all ones.
This patch adds 'ul' type modifiers to the literal numbers passed in
here, so now the expression remains an 'unsigned long' with the upper
bits all zero, and that avoids the signed overflow and the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b1c17215d7 ("stmmac: add ipq806x glue layer")
Signed-off-by: David S. Miller <davem@davemloft.net>
- Support for the ACPI _CCA configuration object intended to tell
the OS whether or not a bus master device supports hardware
managed cache coherency and a new set of functions to allow
drivers to check the cache coherency support for devices in a
platform firmware interface agnostic way (Suravee Suthikulpanit,
Jeremy Linton).
- ACPI backlight quirks for ESPRIMO Mobile M9410 and Dell XPS L421X
(Aaron Lu, Hans de Goede).
- Fixes for the arm_big_little and s5pv210-cpufreq cpufreq drivers
(Jon Medhurst, Nicolas Pitre).
- kfree()-related fixup for the recently introduced CPPC cpufreq
frontend (Markus Elfring).
- intel_pstate fix reducing kernel log noise on systems where
P-states are managed by hardware (Prarit Bhargava).
- intel_pstate maintainers information update (Srinivas Pandruvada).
- cpufreq core optimization related to the handling of delayed work
items used by governors (Viresh Kumar).
- Locking fixes and cleanups of the Operating Performance Points
(OPP) framework (Viresh Kumar).
- Generic power domains framework cleanups (Lina Iyer).
- cpupower tool updates (Jacob Tanenbaum, Sriram Raghunathan,
Thomas Renninger).
- turbostat tool updates (Len Brown).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=XZiP
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"The only new feature in this batch is support for the ACPI _CCA device
configuration object, which it a pre-requisite for future ACPI PCI
support on ARM64, but should not affect the other architectures.
The rest is fixes and cleanups, mostly in cpufreq (including
intel_pstate), the Operating Performace Points (OPP) framework and
tools (cpupower and turbostat).
Specifics:
- Support for the ACPI _CCA configuration object intended to tell the
OS whether or not a bus master device supports hardware managed
cache coherency and a new set of functions to allow drivers to
check the cache coherency support for devices in a platform
firmware interface agnostic way (Suravee Suthikulpanit, Jeremy
Linton).
- ACPI backlight quirks for ESPRIMO Mobile M9410 and Dell XPS L421X
(Aaron Lu, Hans de Goede).
- Fixes for the arm_big_little and s5pv210-cpufreq cpufreq drivers
(Jon Medhurst, Nicolas Pitre).
- kfree()-related fixup for the recently introduced CPPC cpufreq
frontend (Markus Elfring).
- intel_pstate fix reducing kernel log noise on systems where
P-states are managed by hardware (Prarit Bhargava).
- intel_pstate maintainers information update (Srinivas Pandruvada).
- cpufreq core optimization related to the handling of delayed work
items used by governors (Viresh Kumar).
- Locking fixes and cleanups of the Operating Performance Points
(OPP) framework (Viresh Kumar).
- Generic power domains framework cleanups (Lina Iyer).
- cpupower tool updates (Jacob Tanenbaum, Sriram Raghunathan, Thomas
Renninger).
- turbostat tool updates (Len Brown)"
* tag 'pm+acpi-4.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
PCI: ACPI: Add support for PCI device DMA coherency
PCI: OF: Move of_pci_dma_configure() to pci_dma_configure()
of/pci: Fix pci_get_host_bridge_device leak
device property: ACPI: Remove unused DMA APIs
device property: ACPI: Make use of the new DMA Attribute APIs
device property: Adding DMA Attribute APIs for Generic Devices
ACPI: Adding DMA Attribute APIs for ACPI Device
device property: Introducing enum dev_dma_attr
ACPI: Honor ACPI _CCA attribute setting
cpufreq: CPPC: Delete an unnecessary check before the function call kfree()
PM / OPP: Add opp_rcu_lockdep_assert() to _find_device_opp()
PM / OPP: Hold dev_opp_list_lock for writers
PM / OPP: Protect updates to list_dev with mutex
PM / OPP: Propagate error properly from dev_pm_opp_set_sharing_cpus()
cpufreq: s5pv210-cpufreq: fix wrong do_div() usage
MAINTAINERS: update for intel P-state driver
Creating a common structure initialization pattern for struct option
cpupower: Enable disabled Cstates if they are below max latency
cpupower: Remove debug message when using cpupower idle-set -D switch
cpupower: cpupower monitor reports uninitialized values for offline cpus
...
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Fixes: d7d2d89d4b ("r8169: Add software counter for multicast packages")
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge final patch-bomb from Andrew Morton:
"Various leftovers, mainly Christoph's pci_dma_supported() removals"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
pci: remove pci_dma_supported
usbnet: remove ifdefed out call to dma_supported
kaweth: remove ifdefed out call to dma_supported
sfc: don't call dma_supported
nouveau: don't call pci_dma_supported
netup_unidvb: use pci_set_dma_mask insted of pci_dma_supported
cx23885: use pci_set_dma_mask insted of pci_dma_supported
cx25821: use pci_set_dma_mask insted of pci_dma_supported
cx88: use pci_set_dma_mask insted of pci_dma_supported
saa7134: use pci_set_dma_mask insted of pci_dma_supported
saa7164: use pci_set_dma_mask insted of pci_dma_supported
tw68-core: use pci_set_dma_mask insted of pci_dma_supported
pcnet32: use pci_set_dma_mask insted of pci_dma_supported
lib/string.c: add ULL suffix to the constant definition
hugetlb: trivial comment fix
selftests/mlock2: add ULL suffix to 64-bit constants
selftests/mlock2: add missing #define _GNU_SOURCE
Pull networking fixes from David Miller:
1) Fix null deref in xt_TEE netfilter module, from Eric Dumazet.
2) Several spots need to get to the original listner for SYN-ACK
packets, most spots got this ok but some were not. Whilst covering
the remaining cases, create a helper to do this. From Eric Dumazet.
3) Missiing check of return value from alloc_netdev() in CAIF SPI code,
from Rasmus Villemoes.
4) Don't sleep while != TASK_RUNNING in macvtap, from Vlad Yasevich.
5) Use after free in mvneta driver, from Justin Maggard.
6) Fix race on dst->flags access in dst_release(), from Eric Dumazet.
7) Add missing ZLIB_INFLATE dependency for new qed driver. From Arnd
Bergmann.
8) Fix multicast getsockopt deadlock, from WANG Cong.
9) Fix deadlock in btusb, from Kuba Pawlak.
10) Some ipv6_add_dev() failure paths were not cleaning up the SNMP6
counter state. From Sabrina Dubroca.
11) Fix packet_bind() race, which can cause lost notifications, from
Francesco Ruggeri.
12) Fix MAC restoration in qlcnic driver during bonding mode changes,
from Jarod Wilson.
13) Revert bridging forward delay change which broke libvirt and other
userspace things, from Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
Revert "bridge: Allow forward delay to be cfgd when STP enabled"
bpf_trace: Make dependent on PERF_EVENTS
qed: select ZLIB_INFLATE
net: fix a race in dst_release()
net: mvneta: Fix memory use after free.
net: Documentation: Fix default value tcp_limit_output_bytes
macvtap: Resolve possible __might_sleep warning in macvtap_do_read()
mvneta: add FIXED_PHY dependency
net: caif: check return value of alloc_netdev
net: hisilicon: NET_VENDOR_HISILICON should depend on HAS_DMA
drivers: net: xgene: fix RGMII 10/100Mb mode
netfilter: nft_meta: use skb_to_full_sk() helper
net_sched: em_meta: use skb_to_full_sk() helper
sched: cls_flow: use skb_to_full_sk() helper
netfilter: xt_owner: use skb_to_full_sk() helper
smack: use skb_to_full_sk() helper
net: add skb_to_full_sk() helper and use it in selinux_netlbl_skbuff_setsid()
bpf: doc: correct arch list for supported eBPF JIT
dwc_eth_qos: Delete an unnecessary check before the function call "of_node_put"
bonding: fix panic on non-ARPHRD_ETHER enslave failure
...
dma_set_mask already checks for a supported DMA mask before updating it,
the call to dma_supported is redundant.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Shradha Shah <sshah@solarflare.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All drivers should be using dma_set_mask / pci_set_dma_mask to try to
set the dma mask instead of just querying it. Without that some iommu
implementations may not work.
pci_dma_supported is removed entirely, but dma_supported stays for
dma_ops implementations for now.
This patch (of 15):
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Don Fry <pcnet32@frontier.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Helge Deller <deller@gmx.de>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Sergey Kozlov <serjk@netup.ru>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Steven Toth <stoth@kernellabs.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The newly added qlogic qed driver uses the zlib library, but
misses the dependency:
drivers/built-in.o: In function `qed_alloc_stream_mem':
drivers/net/ethernet/qlogic/qed/qed_main.c:707: undefined reference to `zlib_inflate_workspacesize'
drivers/built-in.o: In function `qed_unzip_data':
drivers/net/ethernet/qlogic/qed/qed_main.c:675: undefined reference to `zlib_inflateInit2'
This changes Kconfig to always select zlib when needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: fe56b9e6a8 ("qed: Add module with basic common support")
Signed-off-by: David S. Miller <davem@davemloft.net>
After changing an interface's MTU, then bringing the interface down and
back up again, I immediately saw tons of kernel messages like below.
The reason for this bad behavior is mvneta_rxq_drop_pkts(), which calls
dma_unmap_single() on already-freed memory. So we need to switch the
order of those two operations.
[ 152.388518] BUG: Bad page state in process ifconfig pfn:1b518
[ 152.388526] page:dff3dbc0 count:0 mapcount:0 mapping: (null) index:0x0
[ 152.395178] flags: 0x200(arch_1)
[ 152.398441] page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set
[ 152.398446] bad because of flags:
[ 152.398450] flags: 0x200(arch_1)
[ 152.401716] Modules linked in:
[ 152.401728] CPU: 0 PID: 1453 Comm: ifconfig Tainted: P B O 4.1.12.armada.1 #1
[ 152.401733] Hardware name: Marvell Armada 370/XP (Device Tree)
[ 152.401749] [<c0015b1c>] (unwind_backtrace) from [<c0011d8c>] (show_stack+0x10/0x14)
[ 152.401762] [<c0011d8c>] (show_stack) from [<c06aa68c>] (dump_stack+0x74/0x90)
[ 152.401772] [<c06aa68c>] (dump_stack) from [<c0096c08>] (bad_page+0xc4/0x124)
[ 152.401783] [<c0096c08>] (bad_page) from [<c0099378>] (get_page_from_freelist+0x4e4/0x644)
[ 152.401794] [<c0099378>] (get_page_from_freelist) from [<c0099620>] (__alloc_pages_nodemask+0x148/0x784)
[ 152.401805] [<c0099620>] (__alloc_pages_nodemask) from [<c00ac658>] (kmalloc_order+0x10/0x20)
[ 152.401818] [<c00ac658>] (kmalloc_order) from [<c04c6f44>] (mvneta_rx_refill+0xc4/0xe8)
[ 152.401830] [<c04c6f44>] (mvneta_rx_refill) from [<c04c96c0>] (mvneta_setup_rxqs+0x298/0x39c)
[ 152.401842] [<c04c96c0>] (mvneta_setup_rxqs) from [<c04c9904>] (mvneta_open+0x3c/0x150)
[ 152.401853] [<c04c9904>] (mvneta_open) from [<c0597764>] (__dev_open+0xac/0x124)
[ 152.401864] [<c0597764>] (__dev_open) from [<c05979e4>] (__dev_change_flags+0x8c/0x148)
[ 152.401875] [<c05979e4>] (__dev_change_flags) from [<c0597ac0>] (dev_change_flags+0x18/0x48)
[ 152.401886] [<c0597ac0>] (dev_change_flags) from [<c060d308>] (devinet_ioctl+0x620/0x6d0)
[ 152.401897] [<c060d308>] (devinet_ioctl) from [<c057d810>] (sock_ioctl+0x64/0x288)
[ 152.401908] [<c057d810>] (sock_ioctl) from [<c00dcb7c>] (do_vfs_ioctl+0x78/0x608)
[ 152.401918] [<c00dcb7c>] (do_vfs_ioctl) from [<c00dd170>] (SyS_ioctl+0x64/0x74)
[ 152.401930] [<c00dd170>] (SyS_ioctl) from [<c000f3a0>] (ret_fast_syscall+0x0/0x3c)
Signed-off-by: Justin Maggard <jmaggard@netgear.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fixed_phy infrastructure is done in a way that is optional,
by providing 'static inline' helper functions doing nothing in
include/linux/phy_fixed.h for all its APIs. However, three out
of the four users (DSA, BCMGENET, and SYSTEMPORT) always
'select FIXED_PHY', presumably because they need that.
MVNETA is the fourth one, and if that is built-in but FIXED_PHY
is configured as a loadable module, we get a link error:
drivers/built-in.o: In function `mvneta_fixed_link_update':
fpga-mgr.c:(.text+0x33ed80): undefined reference to `fixed_phy_update_state'
Presumably this driver has the same dependency as the others,
so this patch also uses 'select' to ensure that the fixed-phy
support is built-in.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 898b2970e2 ("mvneta: implement SGMII-based in-band link state signaling")
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the RGMII 10/100M mode by reprogramming the clock.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge second patch-bomb from Andrew Morton:
- most of the rest of MM
- procfs
- lib/ updates
- printk updates
- bitops infrastructure tweaks
- checkpatch updates
- nilfs2 update
- signals
- various other misc bits: coredump, seqfile, kexec, pidns, zlib, ipc,
dma-debug, dma-mapping, ...
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (102 commits)
ipc,msg: drop dst nil validation in copy_msg
include/linux/zutil.h: fix usage example of zlib_adler32()
panic: release stale console lock to always get the logbuf printed out
dma-debug: check nents in dma_sync_sg*
dma-mapping: tidy up dma_parms default handling
pidns: fix set/getpriority and ioprio_set/get in PRIO_USER mode
kexec: use file name as the output message prefix
fs, seqfile: always allow oom killer
seq_file: reuse string_escape_str()
fs/seq_file: use seq_* helpers in seq_hex_dump()
coredump: change zap_threads() and zap_process() to use for_each_thread()
coredump: ensure all coredumping tasks have SIGNAL_GROUP_COREDUMP
signal: remove jffs2_garbage_collect_thread()->allow_signal(SIGCONT)
signal: introduce kernel_signal_stop() to fix jffs2_garbage_collect_thread()
signal: turn dequeue_signal_lock() into kernel_dequeue_signal()
signals: kill block_all_signals() and unblock_all_signals()
nilfs2: fix gcc uninitialized-variable warnings in powerpc build
nilfs2: fix gcc unused-but-set-variable warnings
MAINTAINERS: nilfs2: add header file for tracing
nilfs2: add tracepoints for analyzing reading and writing metadata files
...
- "Checksum offload support in user space" enablement
- Misc cxgb4 fixes, add T6 support
- Misc usnic fixes
- 32 bit build warning fixes
- Misc ocrdma fixes
- Multicast loopback prevention extension
- Extend the GID cache to store and return attributes of GIDs
- Misc iSER updates
- iSER clustering update
- Network NameSpace support for rdma CM
- Work Request cleanup series
- New Memory Registration API
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bBIY
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is my initial round of 4.4 merge window patches. There are a few
other things I wish to get in for 4.4 that aren't in this pull, as
this represents what has gone through merge/build/run testing and not
what is the last few items for which testing is not yet complete.
- "Checksum offload support in user space" enablement
- Misc cxgb4 fixes, add T6 support
- Misc usnic fixes
- 32 bit build warning fixes
- Misc ocrdma fixes
- Multicast loopback prevention extension
- Extend the GID cache to store and return attributes of GIDs
- Misc iSER updates
- iSER clustering update
- Network NameSpace support for rdma CM
- Work Request cleanup series
- New Memory Registration API"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (76 commits)
IB/core, cma: Make __attribute_const__ declarations sparse-friendly
IB/core: Remove old fast registration API
IB/ipath: Remove fast registration from the code
IB/hfi1: Remove fast registration from the code
RDMA/nes: Remove old FRWR API
IB/qib: Remove old FRWR API
iw_cxgb4: Remove old FRWR API
RDMA/cxgb3: Remove old FRWR API
RDMA/ocrdma: Remove old FRWR API
IB/mlx4: Remove old FRWR API support
IB/mlx5: Remove old FRWR API support
IB/srp: Dont allocate a page vector when using fast_reg
IB/srp: Remove srp_finish_mapping
IB/srp: Convert to new registration API
IB/srp: Split srp_map_sg
RDS/IW: Convert to new memory registration API
svcrdma: Port to new memory registration API
xprtrdma: Port to new memory registration API
iser-target: Port to new memory registration API
IB/iser: Port to new fast registration API
...
Pull trivial updates from Jiri Kosina:
"Trivial stuff from trivial tree that can be trivially summed up as:
- treewide drop of spurious unlikely() before IS_ERR() from Viresh
Kumar
- cosmetic fixes (that don't really affect basic functionality of the
driver) for pktcdvd and bcache, from Julia Lawall and Petr Mladek
- various comment / printk fixes and updates all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
bcache: Really show state of work pending bit
hwmon: applesmc: fix comment typos
Kconfig: remove comment about scsi_wait_scan module
class_find_device: fix reference to argument "match"
debugfs: document that debugfs_remove*() accepts NULL and error values
net: Drop unlikely before IS_ERR(_OR_NULL)
mm: Drop unlikely before IS_ERR(_OR_NULL)
fs: Drop unlikely before IS_ERR(_OR_NULL)
drivers: net: Drop unlikely before IS_ERR(_OR_NULL)
drivers: misc: Drop unlikely before IS_ERR(_OR_NULL)
UBI: Update comments to reflect UBI_METAONLY flag
pktcdvd: drop null test before destroy functions
The of_node_put() function tests whether its argument is NULL
and then returns immediately.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding driver saves a copy of slaves' original mac address and then
assigns whatever mac as needed to the slave, depending on mode. In at
least modes 5 and 6 (balance-tlb, balance-alb), it often ends up being the
mac address of another slave. On release from the bond, the original mac
address is supposed to get restored via a dev_set_mac_address() call in
the bonding driver's __bond_release_one() function, which calls the
slave's ndo_set_mac_address function, which for qlcnic, is
qlcnic_set_mac().
Now, this function tries to be somewhat intelligent and exit early if
you're trying to set the mac address to the same thing that is already
set. The problem here is that adapter->mac_addr isn't in sync with
netdev->dev_addr. The qlcnic driver still has the original mac stored in
adapter->mac_addr, while the bonding driver has updated netdev->dev_addr,
so qlcnic thinks we're trying to set the same address it already has.
I think the way to go here, since the function updates both netdev and
adapter's stored mac addresses, is to check if either of them doesn't
match the newly requested mac. Simply checking netdev's value only could
result in a similar mismatch and non-update, so look at both.
CC: Dept-GELinuxNICDev@qlogic.com
CC: netdev@vger.kernel.org
CC: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we have the new DMA attribute APIs, we can replace the older
acpi_check_dma() and device_dma_is_coherent().
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The asm-generic changes for 4.4 are mostly a series from Christoph Hellwig
to clean up various abuses of headers in there. The patch to rename the
io-64-nonatomic-*.h headers caused some conflicts with new users, so I
added a workaround that we can remove in the next merge window.
The only other patch is a warning fix from Marek Vasut
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dQKG
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanups from Arnd Bergmann:
"The asm-generic changes for 4.4 are mostly a series from Christoph
Hellwig to clean up various abuses of headers in there. The patch to
rename the io-64-nonatomic-*.h headers caused some conflicts with new
users, so I added a workaround that we can remove in the next merge
window.
The only other patch is a warning fix from Marek Vasut"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: temporarily add back asm-generic/io-64-nonatomic*.h
asm-generic: cmpxchg: avoid warnings from macro-ized cmpxchg() implementations
gpio-mxc: stop including <asm-generic/bug>
n_tracesink: stop including <asm-generic/bug>
n_tracerouter: stop including <asm-generic/bug>
mlx5: stop including <asm-generic/kmap_types.h>
hifn_795x: stop including <asm-generic/kmap_types.h>
drbd: stop including <asm-generic/kmap_types.h>
move count_zeroes.h out of asm-generic
move io-64-nonatomic*.h out of asm-generic
Instead of always calling pci_sriov_disable() in remove_one(),
the driver should detect whether VFs are currently assigned
to the VMs. If the VFs are active in VMs, then it should not
disable SRIOV as it is catastrophic to the VMs. Instead,
it just leaves the VFs alone and continues to unload the PF.
The user can then cleanup the VMs even after the PF driver
has been unloaded.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign the return value from bitmap_find_free_region() to an integer
variable and check for negative error codes first, before assigning
the bit ID to the unsigned sw_id field.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to use offset 0x4014 for reading CAG interrupt status,
the actual CAG register must be mapped to GRC bar0 window #4.
Otherwise, the driver is reading garbage. This patch corrects
this issue.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The profile ID in the completion record needs to be ANDed with the
profile ID mask of 0x1f. This bug was causing the SKB hash type
and the gso_type to be wrong in some cases.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the sp event bits to be bit positions instead of bit values since
the bit helper functions are expecting the former.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
The variable phy_iface is double-initialized to itself.
This patch remove that.
Reported-by: coverity (CID 1271141)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally return success instead of -ENOMEM here.
Fixes: fe56b9e6a8 ('qed: Add module with basic common support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch of
debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6ePQACgkQMUfUDdst+ymNTgCgpP0CZw57GpwF/Hp2L/lMkVeo
Kx8AoKhEi4iqD5fdCQS9qTfomB+2/M6g
=g7ZO
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch
of debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time"
* tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Add debugfs_create_ulong()
of: to support binding numa node to specified device in devicetree
debugfs: Add read-only/write-only bool file ops
debugfs: Add read-only/write-only size_t file ops
debugfs: Add read-only/write-only x64 file ops
debugfs: Consolidate file mode checks in debugfs_create_*()
Revert "mm: Check if section present during memory block (un)registering"
driver-core: platform: Provide helpers for multi-driver modules
mm: Check if section present during memory block (un)registering
devres: fix a for loop bounds check
CMA: fix CONFIG_CMA_SIZE_MBYTES overflow in 64bit
base/platform: assert that dev_pm_domain callbacks are called unconditionally
sysfs: correctly handle short reads on PREALLOC attrs.
base: soc: siplify ida usage
kobject: move EXPORT_SYMBOL() macros next to corresponding definitions
kobject: explain what kobject's sd field is
debugfs: document that debugfs_remove*() accepts NULL and error values
debugfs: Pass bool pointer to debugfs_create_bool()
ACPI / EC: Fix broken 64bit big-endian users of 'global_lock'
VXLAN may be a loadable module, and this driver cannot be built-in
in that case, or we get a link error:
drivers/built-in.o: In function `__bnxt_open_nic':
drivers/net/ethernet/broadcom/bnxt/bnxt.c:4581: undefined reference to `vxlan_get_rx_port'
This adds a Kconfig dependency that ensures that either VXLAN is
disabled (which the driver handles correctly), or we depend on
VXLAN itself and disallow built-in compilation when VXLAN is
a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MODE_MF_SI is 9. We should be testing bit 9 instead of AND 0x9.
Fixes: fe56b9e6a8 ('qed: Add module with basic common support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We check if "p_hwfn" is NULL and then dereference it in the error
handling code. I read the code and it isn't NULL so let's remove the
check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the ring allocation is done by a single function, sh_eth_ring_init(),
the ring deallocation was split into two functions (almost always called
one after the other) for no good reason. Merge sh_eth_free_dma_buffer()
into sh_eth_ring_free() which allows us to save space not only on the
direct calls of the former function but also on the sh_eth_ring_init()'s
simplified error path...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'ret' local variable in sh_eth_ring_init() serves no useful purpose as
the only values it gets assigned are 0 and -ENOMEM both of which could be
returned directly...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a fixed-link devicetree sub-node in case the the
cpsw MAC is directly connected to a non-mdio PHY/device.
Signed-off-by: Markus Brunner <systemprogrammierung.brunner@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
Changes of note:
1) Allow to schedule ICMP packets in IPVS, from Alex Gartrell.
2) Provide FIB table ID in ipv4 route dumps just as ipv6 does, from
David Ahern.
3) Allow the user to ask for the statistics to be filtered out of
ipv4/ipv6 address netlink dumps. From Sowmini Varadhan.
4) More work to pass the network namespace context around deep into
various packet path APIs, starting with the netfilter hooks. From
Eric W Biederman.
5) Add layer 2 TX/RX checksum offloading to qeth driver, from Thomas
Richter.
6) Use usec resolution for SYN/ACK RTTs in TCP, from Yuchung Cheng.
7) Support Very High Throughput in wireless MESH code, from Bob
Copeland.
8) Allow setting the ageing_time in switchdev/rocker. From Scott
Feldman.
9) Properly autoload L2TP type modules, from Stephen Hemminger.
10) Fix and enable offload features by default in 8139cp driver, from
David Woodhouse.
11) Support both ipv4 and ipv6 sockets in a single vxlan device, from
Jiri Benc.
12) Fix CWND limiting of thin streams in TCP, from Bendik Rønning
Opstad.
13) Fix IPSEC flowcache overflows on large systems, from Steffen
Klassert.
14) Convert bridging to track VLANs using rhashtable entries rather than
a bitmap. From Nikolay Aleksandrov.
15) Make TCP listener handling completely lockless, this is a major
accomplishment. Incoming request sockets now live in the
established hash table just like any other socket too.
From Eric Dumazet.
15) Provide more bridging attributes to netlink, from Nikolay
Aleksandrov.
16) Use hash based algorithm for ipv4 multipath routing, this was very
long overdue. From Peter Nørlund.
17) Several y2038 cures, mostly avoiding timespec. From Arnd Bergmann.
18) Allow non-root execution of EBPF programs, from Alexei Starovoitov.
19) Support SO_INCOMING_CPU as setsockopt, from Eric Dumazet. This
influences the port binding selection logic used by SO_REUSEPORT.
20) Add ipv6 support to VRF, from David Ahern.
21) Add support for Mellanox Spectrum switch ASIC, from Jiri Pirko.
22) Add rtl8xxxu Realtek wireless driver, from Jes Sorensen.
23) Implement RACK loss recovery in TCP, from Yuchung Cheng.
24) Support multipath routes in MPLS, from Roopa Prabhu.
25) Fix POLLOUT notification for listening sockets in AF_UNIX, from Eric
Dumazet.
26) Add new QED Qlogic river, from Yuval Mintz, Manish Chopra, and
Sudarsana Kalluru.
27) Don't fetch timestamps on AF_UNIX sockets, from Hannes Frederic
Sowa.
28) Support ipv6 geneve tunnels, from John W Linville.
29) Add flood control support to switchdev layer, from Ido Schimmel.
30) Fix CHECKSUM_PARTIAL handling of potentially fragmented frames, from
Hannes Frederic Sowa.
31) Support persistent maps and progs in bpf, from Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1790 commits)
sh_eth: use DMA barriers
switchdev: respect SKIP_EOPNOTSUPP flag in case there is no recursion
net: sched: kill dead code in sch_choke.c
irda: Delete an unnecessary check before the function call "irlmp_unregister_service"
net: dsa: mv88e6xxx: include DSA ports in VLANs
net: dsa: mv88e6xxx: disable SA learning for DSA and CPU ports
net/core: fix for_each_netdev_feature
vlan: Invoke driver vlan hooks only if device is present
arcnet/com20020: add LEDS_CLASS dependency
bpf, verifier: annotate verbose printer with __printf
dp83640: Only wait for timestamps for packets with timestamping enabled.
ptp: Change ptp_class to a proper bitmask
dp83640: Prune rx timestamp list before reading from it
dp83640: Delay scheduled work.
dp83640: Include hash in timestamp/packet matching
ipv6: fix tunnel error handling
net/mlx5e: Fix LSO vlan insertion
net/mlx5e: Re-eanble client vlan TX acceleration
net/mlx5e: Return error in case mlx5e_set_features() fails
net/mlx5e: Don't allow more than max supported channels
...
Pull locking changes from Ingo Molnar:
"The main changes in this cycle were:
- More gradual enhancements to atomic ops: new atomic*_read_ctrl()
ops, synchronize atomic_{read,set}() ordering requirements between
architectures, add atomic_long_t bitops. (Peter Zijlstra)
- Add _{relaxed|acquire|release}() variants for inc/dec atomics and
use them in various locking primitives: mutex, rtmutex, mcs, rwsem.
This enables weakly ordered architectures (such as arm64) to make
use of more locking related optimizations. (Davidlohr Bueso)
- Implement atomic[64]_{inc,dec}_relaxed() on ARM. (Will Deacon)
- Futex kernel data cache footprint micro-optimization. (Rasmus
Villemoes)
- pvqspinlock runtime overhead micro-optimization. (Waiman Long)
- misc smaller fixlets"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ARM, locking/atomics: Implement _relaxed variants of atomic[64]_{inc,dec}
locking/rwsem: Use acquire/release semantics
locking/mcs: Use acquire/release semantics
locking/rtmutex: Use acquire/release semantics
locking/mutex: Use acquire/release semantics
locking/asm-generic: Add _{relaxed|acquire|release}() variants for inc/dec atomics
atomic: Implement atomic_read_ctrl()
atomic, arch: Audit atomic_{read,set}()
atomic: Add atomic_long_t bitops
futex: Force hot variables into a single cache line
locking/pvqspinlock: Kick the PV CPU unconditionally when _Q_SLOW_VAL
locking/osq: Relax atomic semantics
locking/qrwlock: Rename ->lock to ->wait_lock
locking/Documentation/lockstat: Fix typo - lokcing -> locking
locking/atomics, cmpxchg: Privatize the inclusion of asm/cmpxchg.h
Pull timer updates from Thomas Gleixner:
"The timer departement provides:
- More y2038 work in the area of ntp and pps.
- Optimization of posix cpu timers
- New time related selftests
- Some new clocksource drivers
- The usual pile of fixes, cleanups and improvements"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
timeconst: Update path in comment
timers/x86/hpet: Type adjustments
clocksource/drivers/armada-370-xp: Implement ARM delay timer
clocksource/drivers/tango_xtal: Add new timer for Tango SoCs
clocksource/drivers/imx: Allow timer irq affinity change
clocksource/drivers/exynos_mct: Use container_of() instead of this_cpu_ptr()
clocksource/drivers/h8300_*: Remove unneeded memset()s
clocksource/drivers/sh_cmt: Remove unneeded memset() in sh_cmt_setup()
clocksource/drivers/em_sti: Remove unneeded memset()s
clocksource/drivers/mediatek: Use GPT as sched clock source
clockevents/drivers/mtk: Fix spurious interrupt leading to crash
posix_cpu_timer: Reduce unnecessary sighand lock contention
posix_cpu_timer: Convert cputimer->running to bool
posix_cpu_timer: Check thread timers only when there are active thread timers
posix_cpu_timer: Optimize fastpath_timer_check()
timers, kselftest: Add 'adjtick' test to validate adjtimex() tick adjustments
timers: Use __fls in apply_slack()
clocksource: Remove return statement from void functions
net: sfc: avoid using timespec
ntp/pps: use y2038 safe types in pps_event_time
...
Commit 7d7355f58b ("sh_eth: Ensure proper ordering of descriptor active
bit write/read") did the right thing but used too "heavy" barriers while
there were already "lighter" DMA barriers exactly for this case...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider vlan insertion impact on headers copy size also for LSO
packets.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit cd58c714ac "net/mlx5e: Disable client vlan TX acceleration".
Bring back client vlan insertion offload, the original
performance issue was found and fixed in the next patch.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case mlx5e_set_features() fails, return the failure status rather
than 0.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider MLX5E_MAX_NUM_CHANNELS @ethtool set/get_channels
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of storing the msix array index in eq->irqn (vecidx),
store the real irq number.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use jiffies rather than wait loop with msleep().
The wait loop didn't take into consideration time when the
process was not executing.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a configuration operation that involves closing and re-opening
resources (e.g RX/TX queue size change) fails at the re-opening stage
these resources will remain closed.
So when executing (following) configuration operations (e.g ifconfig
down) we cannot assume that these resources are available.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the IP stack passes SKBs the sfc driver puts them in 2 different TX
queues (called partners), one for checksummed and one for not checksummed.
If the SKB has xmit_more set the driver will delay pushing the work to the
NIC.
When later it does decide to push the buffers this patch ensures it also
pushes the partner queue, if that also has any delayed work. Before this
fix the work in the partner queue would be left for a long time and cause
a netdev watchdog.
Fixes: 70b33fb ("sfc: add support for skb->xmit_more")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct name of the RX descriptor 0 bit 30 is RDLE (receive descriptor
list end), not RDEL.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corrects what appear to be typos, making the code consistent with
itself, and allowing meaningful prefixes to be displayed with the errors in
question.
Before:
(null): failed to initialize MDIO
(null): Cannot allocate desc base address table (size 176 bytes)
After:
ravb e6800000.ethernet: failed to initialize MDIO
ravb e6800000.ethernet: Cannot allocate desc base address table (size 176 bytes)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_ring_free() called in the sh_eth_ring_init()'s error path expects
the arrays pointed to by 'sh_eth_private::[rt]x_skbuff' to be initialized
with NULLs but they are allocated with just kmalloc_array() and so are left
filled with random data. Use kcalloc() instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver Kconfig symbol is tristate which means that it can be built as
a module but the module alias information is not added to the module info
so module autoload won't work since user-space won't have the information.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver's SPI id table is expected to be an array of struct spi_device_id
that ends with a zero-initialized sentinel entry. But this driver defines
the table as a single struct spi_device_id and sets .id_table to a pointer
to this struct.
But spi_match_id() has a loop that iterates while the struct spi_device_id
.name[0] is not NULL, so not having a sentinel can cause a NULL pointer
deference error.
This patch defines the SPI id table correctly as all other SPI drivers do.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The affinity hint is used by the user space daemon, irqbalancer, to
indicate a preferred CPU mask for irqs. This patch sets the irq affinity
hint to local numa core first, when exausted we try non-local numa cores.
Also set tx xps cpus mask bassed on affinity hint.
v2: remove the global affinity policy.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
priv->hwts_*_en indicate if timestamping is enabled/disabled at run
time. But priv->dma_cap.time_stamp and priv->dma_cap.atime_stamp
indicates HW is support for PTPv1/PTPv2.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_driver doesn't need to set .owner, because
platform_driver_register() will set it.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EPHY on GENET v1->v3 is extremely finicky, and will show occasional
failures based on the timing and reset sequence, ranging from duplicate
packets, to extremely high latencies.
Perform an additional software reset, and re-configuration to make sure it is
in a consistent and working state.
Fixes: 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On certain hardware in certain situations loopback test fails and the
driver gets removed. During mdiobus_unregister() instance of PHY driver
gets disposed. But by this time it has already been started using
phy_connect_direct().
PHY driver uses DELAYED_WORK in order to maintain its state. Attempting
to dispose the driver without calling phy_disconnect() causes deallocation
of DELAYED_WORK being active. This shortly causes a bad crash in timer
code.
The problem can be discovered by enabling CONFIG_DEBUG_OBJECTS_TIMERS and
CONFIG_DEBUG_OBJECTS_FREE
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are in a context where we can sleep, and the FEC PHY reset gpio
may be on an I2C expander. Use the cansleep() variant when
setting the GPIO value.
Based on a patch from Russell King for pci-mvebu.c.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a place where checkpatch complains that braces should be used
on all arms of this statement.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes those places where checkpatch complains that comparisons
should place the constant on the right side of the test.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value passed through switchdev attr set is not in jiffies, but in
clock_t, so fix the convert.
Reported-by: Sagi Rotem <sagir@mellanox.com>
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original description was for LAG, so fix it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add or remove a bridged port from the flooding domain of unknown unicast
packets according to user configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling a range of VLANs on a bridged port we can configure
flooding for these VLANs by one register access instead of calling the
same register for each VLAN. This is accomplished by using the 'range'
field of the Switch Flooding Table Register (SFTR).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a flag anyway, so move it to existing u8 flag and don't waste mem.
Fix the flags to be in single u8 on the way.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RGMII TX/RX delay configuration support. RGMII standard requires 2ns
delay to help the RGMII bridge receiver to sample data correctly. If the
default value does not provide proper centering of the data sample, the
TX/RX delay parameters can be used to adjust accordingly.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing memcpy/memset of EQEs, we should use sizeof struct
mlx4_eqe as the base size and not caps.eqe_size which could be bigger.
If caps.eqe_size is bigger than the struct mlx4_eqe then we corrupt
data in the master context.
When using a 64 byte stride, the memcpy copied over 63 bytes to the
slave_eq structure. This resulted in copying over the entire eqe of
interest, including its ownership bit -- and also 31 bytes of garbage
into the next WQE in the slave EQ -- which did NOT include the ownership
bit (and therefore had no impact).
However, once the stride is increased to 128, we are overwriting the
ownership bits of *three* eqes in the slave_eq struct. This results
in an incorrect ownership bit for those eqes, which causes the eq to
seem to be full. The issue therefore surfaced only once 128-byte EQEs
started being used in SRIOV and (overarchitectures that have 128/256
byte cache-lines such as PPC) - e.g after commit 77507aa249
"net/mlx4_core: Enable CQE/EQE stride support".
Fixes: 08ff32352d ('mlx4: 64-byte CQE/EQE support')
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not set the ins_vlan field to zero when no vlan id is present in the packet.
Since WQEs in the TX ring are not zeroed out between uses, this oversight
could result in having vlan flags present in the WQE ctrl segment when no
vlan is preset.
Fixes: e38af4faf0 ('net/mlx4_en: Add support for hardware accelerated 802.1ad vlan')
Reported-by: Gideon Naim <gideonn@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
delete action of ETHTOOL_ID_ON/ETHTOOL_ID_OFF in XGE ethtool -p,
so Hardware control the LED state instead of software.
Signed-off-by: Li Peng <lipeng321@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increased TX_TIMEOUT to 5HZ to accommodate worst case situation
for traffic and CPU intensive use cases
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Abhimanyu <abhimanyu@freescale.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During Tx cleanup it's still possible for the descriptor data to be
read ahead of the descriptor index. A memory barrier is required between
the read of the descriptor index and the start of the Tx cleanup loop.
This allows a change to a lighter-weight barrier in the Tx transmit
routine just before updating the current descriptor index.
Since the memory barrier does result in extra overhead on arm64, keep
the previous change to not chase the current descriptor value. This
prevents the execution of the barrier for each loop performed.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forcedeth currently uses disable_irq_lockdep and enable_irq_lockdep, which in
some configurations simply calls local_irq_disable. This causes errant warnings
in the netpoll path as in netpoll_send_skb_on_dev, where we disable irqs using
local_irq_save, leading to the following warning:
WARNING: at net/core/netpoll.c:352 netpoll_send_skb_on_dev+0x243/0x250() (Not
tainted)
Hardware name:
netpoll_send_skb_on_dev(): eth0 enabled interrupts in poll
(nv_start_xmit_optimized+0x0/0x860 [forcedeth])
Modules linked in: netconsole(+) configfs ipv6 iptable_filter ip_tables ppdev
parport_pc parport sg microcode serio_raw edac_core edac_mce_amd k8temp
snd_hda_codec_realtek snd_hda_codec_generic forcedeth snd_hda_intel
snd_hda_codec snd_hwdep snd_seq snd_seq_device snd_pcm snd_timer snd soundcore
snd_page_alloc i2c_nforce2 i2c_core shpchp ext4 jbd2 mbcache sr_mod cdrom sd_mod
crc_t10dif pata_amd ata_generic pata_acpi sata_nv dm_mirror dm_region_hash
dm_log dm_mod [last unloaded: scsi_wait_scan]
Pid: 1940, comm: modprobe Not tainted 2.6.32-573.7.1.el6.x86_64.debug #1
Call Trace:
[<ffffffff8107bbc1>] ? warn_slowpath_common+0x91/0xe0
[<ffffffff8107bcc6>] ? warn_slowpath_fmt+0x46/0x60
[<ffffffffa00fe5b0>] ? nv_start_xmit_optimized+0x0/0x860 [forcedeth]
[<ffffffff814b3593>] ? netpoll_send_skb_on_dev+0x243/0x250
[<ffffffff814b37c9>] ? netpoll_send_udp+0x229/0x270
[<ffffffffa02e3299>] ? write_msg+0x39/0x110 [netconsole]
[<ffffffffa02e331b>] ? write_msg+0xbb/0x110 [netconsole]
[<ffffffff8107bd55>] ? __call_console_drivers+0x75/0x90
[<ffffffff8107bdba>] ? _call_console_drivers+0x4a/0x80
[<ffffffff8107c445>] ? release_console_sem+0xe5/0x250
[<ffffffff8107d200>] ? register_console+0x190/0x3e0
[<ffffffffa02e71a6>] ? init_netconsole+0x1a6/0x216 [netconsole]
[<ffffffffa02e7000>] ? init_netconsole+0x0/0x216 [netconsole]
[<ffffffff810020d0>] ? do_one_initcall+0xc0/0x280
[<ffffffff810d4933>] ? sys_init_module+0xe3/0x260
[<ffffffff8100b0d2>] ? system_call_fastpath+0x16/0x1b
---[ end trace f349c7af88e6a6d5 ]---
console [netcon0] enabled
netconsole: network logging started
Fix it by modifying the forcedeth code to use
disable_irq_nosync_lockdep_irqsavedisable_irq_nosync_lockdep_irqsave instead,
which saves and restores irq state properly. This also saves us a little code
in the process
Tested by the reporter, with successful restuls
Patch applies to the head of the net tree
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces the overhead of locking for busy poll.
Previously the state was protected by a lock, whereas now
it's manipulated solely with atomic operations.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic ethtool operations to the qed driver, allowing support in:
- Statistics gathering [ethtool -S]
- Setting of debug level [ethtool -s <interface> msglvl]
- Getting basic information [ethtool, ethtool -i]
In addition it adds the ability to change the MTU.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device statistics can be gathered on-demand. This adds the qed support for
reading the statistics [both function and port] from the device, and adds
to the public API a method for requesting the current statistics.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic link functionality to qede - driver still doesn't provide
users with an API to change any link property, but it does request qed to
initialize the link using default configuration, and registers a callback
that allows it to get link notifications.
This patch adds the ability of the driver to set the carrier as active and
to enable traffic as a result of async. link notifications.
Following this patch, driver should be capable of running traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical link is handled by the management Firmware.
This patch lays the infrastructure for attention handling in the driver,
as link change notifications arrive via async. attentions,
as well the handling of such notifications.
This patch also extends the API with the protocol drivers by adding
registered callbacks which the protocol driver passes to qed in order
to be notified of async. events originating from the FW/HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to configure basic classification in driver by
implementing ndo_set_mac_address() and ndo_set_rx_mode().
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes the basic Rx/Tx support for the driver [although
carrier will still never be turned on].
Following this patch the driver registers a network device, initializes
it and prepares it for traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds to the qed the support to configure various L2 elements,
such as channels and basic filtering conditions.
It also enhances its public API to allow qede to later utilize this
functionality.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver for Ethernet is the Ethernet specific module for
QL4xxx ethernet products by Qlogic.
This patch adds a very minimal PCI driver, one that doesn't yet register
a network device, but one that does interact with qed and does a basic
initialization of the HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a public API for a network driver to work on top of QED.
The interface itself is very minimal - it's mostly infrastructure, as the
only content it has after this patch is a query for HW-based information
required for the creation of a network interface [I.e., no actual
protocol-specific configurations are supported].
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver is the backend module for the QL4xxx ethernet
products by Qlogic.
This module serves two main purposes:
1. It's responsible to contain all the common code that will be shared
between the various drivers that would be used with said line of
products. Flows such as chip initialization and de-initialization
fall under this category.
2. It would abstract the protocol-specific HW & FW components, allowing
the protocol drivers to have a clean APIs which is detached in its
slowpath configuration from the actual HSI.
This adds a very basic module without any protocol-specific bits.
I.e., this adds a basic implementation that almost entirely falls under
the first category.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
for_each_available_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression r.n;
expression r,e;
@@
for_each_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression r.n;
expression r,e;
@@
for_each_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX buffer size calulation failed to account for the length granularity
(which is now 32 bytes)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both Renesas R-Car and RZ/A1 manuals state that RX buffer length must be
a multiple of 32 bytes, while the driver only uses 16 byte granularity...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_gro_skb() has unused variables when CONFIG_INET is not set. We
really cannot support hardware GRO if CONFIG_INET is not set, so
compile out bnxt_gro_skb() completely and define BNXT_FLAG_GRO to be 0
if CONFIG_INET is not set. This will effectively always disable
hardware GRO if CONFIG_INET is not set.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx BSY error interrupt indicates that a frame was
received and discarded due to lack of buffers, so it's
a rx ring overflow condition and has nothing to do with
with bad rx packets. Use the right counter.
BSY conditions happen when the SoC is under performance
stress. Doing *more* work in stress situations by trying
to schedule NAPI is not a good idea as the stressed system
becomes still more stressed. The Rx interrupt is already
at work making sure the NAPI is scheduled.
So calling gfar_receive() here does not help. This issue
was present since day 1.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under one unusual circumstance it's possible to wrongly set
FILREN without enabling PRSDEP as well in the RCTRL register,
against the hardware specifications. With the default config
this does not happen because the default Rx offloads (Rx csum
and Rx VLAN) properly enable PRSDEP. But if anyone disables
all these offloads (via ethtool), we get a wrong configuration
were the Rx flow classification and hashing, and other Filer
based features (e.g. wake-on-filer interrupt) won't work.
This patch fixes the issue.
Also, account for Rx FCB insertion which happens every time
PRSDEP is set.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RQFCR_AND is duplicated.
Add missing space as well.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the mask used to update the LED configuration so that it clears
the necessary bits as well as setting the bits according to the mask.
Also reverse the LED configuration to show the Link state + collisions in
LEDA and the Link state + TX/RX events in LEDB.
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing function to clear the MIB statatistics was using the
wrong address for the registers. Also, the counters would of been
cleared when the interface was brought up, not during the
probe. Fix both of these.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the ethtool statistic interface, returning the full set
of statistics which both Armada 370, 38x and Armada XP can support.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ThunderX pass2 CPI and MPI configuration changes.
MPI_ALG is not enabled i.e MCAM parsing is disabled.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test for pass-1 silicon was incorrect, it should be for all
revisions less than 8. Also the revision is already present in the
pci_dev, so there is no need to read and keep a private copy.
Remove rev_id and code to read it from struct nicpf. Create new
static inline function pass1_silicon() to be used to testing the
silicon version. Use pass1_silicon() for revision checks, this will
be more widely used in follow on patches.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some silicon revisions, the soft reset clobbers PCI config space,
so quit doing the reset.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
struct bnxt_pf_info needs to be always defined. Move bnxt_update_vf_mac()
to bnxt_sriov.c and add some missing #ifdef CONFIG_BNXT_SRIOV.
Reported-by: Jim Hull <jim.hull@hpe.com>
Tested-by: Jim Hull <jim.hull@hpe.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-23
This series contains updates to i40e, i40evf, if_link, ixgbe and ixgbevf.
Anjali adds a workaround to drop any flow control frames from being
transmitted from any VSI, so that a malicious VF cannot send flow control
or PFC packets out on the wire. Also fixed a bug in debugfs by grabbing
the filter list lock before adding or deleting a filter.
Akeem fixes an issue where we were unconditionally returning VEB bridge
mode before allowing LB in the add VSI routine, resolve by checking if
the bridge is actually in VEB mode first.
Mitch fixed an issue where the incorrect structure was being used for
VLAN filter list, which meant the VLAN filter list did not get
processed correctly and VLAN filters would not be re-enabled after any
kind of reset.
Helin fixed a problem of possibly getting inconsistent flow control
status after a PF reset. The issue was requested_mode was being set
with a default value during probe, but the hardware state could be a
different value from this mode.
Carolyn fixed a problem where the driver output of the OEM version
string varied from the other tools.
Jean Sacren fixes up kernel documentation by fixing function header
comments to match actual variables used in the functions. Also
cleaned up variable initialization, when the variable would be
over-written immediately.
Hiroshi Shimanoto provides three patches to add "trusted" VF by adding
netlink directives and an NDO entry. Then implement these new controls
in ixgbe and ixgbevf. This series has gone through several iterations
to address all the suggested community changes and concerns.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The limitation of the number of multicast address for VF is not enough
for the large scale server with SR-IOV feature. IPv6 requires the multicast
MAC address for each IP address to handle the Neighbor Solicitation
message. We couldn't assign over 30 IPv6 addresses to a single VF.
This patch introduces the new mailbox API, IXGBE_VF_UPDATE_XCAST_MODE,
to update multicast mode of VF. This adds 3 modes;
- NONE only L2 exact match addresses or Flow Director enabled
- MULTI BAM and ROMPE set
- ALLMULTI BAM, ROMPE and MPE set
If a guest VF user wants over 30 MAC multicast addresses, set IFF_ALLMULTI
to request PF to update xcast mode to enable VF multicast promiscuous mode.
On the other hand, enabling VF multicast promiscuous mode may affect
security and performance in the network of the NIC. Only trusted VF can
enable multicast promiscuous mode. The behavior of untrusted VF is the
same as previous version.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implements the new netdev op to trust VF in ixgbe.
The administrator can turn on and off VF trusted by ip command which
supports trust message.
# ip link set dev eth0 vf 1 trust on
or
# ip link set dev eth0 vf 1 trust off
Send a ping to reset VF on changing the status of trusting.
VF driver will reconfigure its features on reset.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no reasons to probe cpsw from late_initcall level
and it's not recommended. Hence, use module_platform_driver()
to register and probe cpsw driver from module_init() level.
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 3092e5e4cc79 ("i40e: add little endian conversion for
checksum") fixed the checksum bug on big-endian architecture.
But we should not execute cpu_to_le16() unconditionally. Thus, put
cpu_to_le16() under certain condition.
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In both i40e_calc_nvm_checksum() and i40e_update_nvm_checksum(), the
local variables designated by 'ret_code' are overwritten immediately. As
such, they should merely be declared.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In i40evf_msix_aq(), the first two lines of rd32() are mainly to clear
the registers. If we initialize 'val' at this point, it will be
overwritten immediately. We shall simply discard the return value here.
When we initialize 'val', we might as well include the mask in one step.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The following kernel-doc arguments for their respective functions are
missing:
1) @cd_type_cmd_tso_mss for i40e_tso();
2) @cd_type_cmd_tso_mss for i40e_tsyn();
3) @tx_ring for i40e_tx_enable_csum().
Add them all for the kernel-doc requirement.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
@flush has been missing since the inception of i40evf_irq_enable(). Add
it for the kernel doc.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of using a custom approach change the code to use %*ph format
specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump up the version...
Change-ID: Ib8d501021671ba20250115ed54330e2c182255b7
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a call to enable SR-IOV in the kernel failed, we need to disable
I40E_FLAG_VEB_MODE_ENABLED, so that bridge mode could fall back to
VEPA, which is a default.
Change-ID: I12b6f776769506db85b29bea94b9c88d0b5ee65e
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where the driver output of the OEM
version string varied from the other tools. The mask value
and the order of operations were incorrect, per the original
change request. Without this patch, the version string will
appear incorrect from the driver.
Change-ID: Ie1ca6485284b4ce3b57e5a99b18b7641617c7ef7
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem of possibly getting inconsistent flow control
statuses after a PF reset. Requested_mode was being set with a default
value during probing, but the initial HW state could be different from
this mode.
Change-ID: I772bf07b78616e87086418d4bd87954b66fa17cd
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Not sure how this compiles at all. Use the correct struct for
manipulating the VLAN filter list. Without this, the VLAN filter
list doesn't get processed correctly, and VLAN filters will not
be re-enabled after any kind of reset.
Change-ID: Iceff2dc089f303058fb71ecb08419eed471e0e90
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix i40e_is_vsi_uplink_mode_veb to check if bridge is actually
in VEB mode before allowing LB in the add VSI routine, instead of
unconditionally returning VEB bridge mode.
Change-ID: I162397b1bdd02367735fe9baaeb51465be2a3ce9
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new code flow requires us to grab the filter list lock before
adding/deleting the filter.
Change-ID: I4eaef508ab4da2d1b2e23f20f2a78d931d5b6aeb
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a workaround to drop any flow control frames from being
transmitted from any VSI. FW can still send flow control frames if flow
control is enabled.
With this patch in place a malicious VF cannot send flow control or PFC
packets out on the wire.
Change-ID: I4303b24e98b93066d2767fec24dfe78be591c277
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code currently uses the lightweight dma_wmb barrier before updating
the current descriptor count. Under heavy load, the Tx cleanup routine
was seeing the updated current descriptor count before the updated
descriptor information. As a result, the Tx descriptor was being cleaned
up before it was used because it was not "owned" by the hardware yet,
resulting in a Tx queue hang.
Using the wmb barrier insures that the descriptor is updated before the
descriptor counter preventing the Tx queue hang. For extra insurance,
the Tx cleanup routine is changed to grab the current decriptor count on
entry and uses that initial value in the processing loop rather than
trying to chase the current value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom ethernet driver for the new family of NetXtreme-C/E
ethernet devices.
v5:
- Removed empty blank lines at end of files (noted by David Miller).
- Moved busy poll helper functions to bnxt.h to at least make the
.c file look less cluttered with #ifdef (noted by Stephen Hemminger).
v4:
- Broke up 2 long message strings with "\n" (suggested by John Linville)
- Constify an array of strings (suggested by Stephen Hemminger)
- Improve bnxt_vf_pciid() (suggested by Stephen Hemminger)
- Use PCI_VDEVICE() to populate pci_device_id table for more compact
source.
v3:
- Fixed 2 more sparse warnings.
- Removed some unused structures in .h files.
v2:
- Fixed all kbuild test robot reported warnings.
- Fixed many of the checkpatch.pl errors and warnings.
- Fixed the Kconfig description (noted by Dmitry Kravkov).
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was printing a message about not being able
to assign VMDq because of a lack of MSI-X vectors.
This was because a line was missing that initialized a variable,
simply a merge error.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code was setting up stats that were not being initialized.
This caused several counters to be displayed incorrectly, due
to indexing beyond the array of strings when printing stats.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
the global Soc configuration is treated by syscon, and sub ctrl bus is
Soc bus. it has to be treated by syscon.
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update ethtool get_drvinfo to display regdump len and also update
firmware string version print to display N/A in case FW isn't present
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the ethtool set_settings() routine we need to remember our old L1
Configuration in case the firmware rejects the request and then restore
that.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For {1, 10, 40} Gb/s. Prohibiting turning off autonegotiation isn't anywhere
in the standard.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
