"previous" is a better name for the variable storing the previous
asynchronous request, better than the opaque name "data" atleast.
We see that we assign the return status to the returned variable
on all code paths, so we might as well just do that immediately
after calling mmc_finalize_areq().
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to reuse the code for CQE support.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to reuse the code for CQE support.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out data preparation into a separate function mmc_blk_data_prep()
which can be re-used for command queuing.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_apply_rel_rw() will be used by Software Command Queuing also. In that
case the command argument is not the block address so change
mmc_apply_rel_rw() to get block address from the request.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
RPMB does not allow Command Queue commands. Disable and re-enable the
Command Queue when switching.
Note that the driver only switches partitions when the queue is empty.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Normal read and write commands may not be used while the command queue is
enabled. Disable the Command Queue when mmc_test is probed and re-enable it
when it is removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eMMC can have multiple internal partitions that are represented as separate
disks / queues. However switching between partitions is only done when the
queue is empty. Consequently the array of mmc requests that are queued can
be shared between partitions saving memory.
Keep a pointer to the mmc request queue on the card, and use that instead
of allocating a new one for each partition.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change from viewing the requests in progress as 'current' and 'previous',
to viewing them as a queue. The current request is allocated to the first
free slot. The presence of incomplete requests is determined from the
count (mq->qcnt) of entries in the queue. Non-read-write requests (i.e.
discards and flushes) are not added to the queue at all and require no
special handling. Also no special handling is needed for the
MMC_BLK_NEW_REQUEST case.
As well as allowing an arbitrarily sized queue, the queue thread function
is significantly simpler.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A subsequent patch will remove 'mq->mqrq_cur'. Prepare for that by
assigning it to a local variable.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out setting the response configuration bits thus further reducing
complexity of function meson_mmc_start_cmd.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out setting the block size. This also contributes to reducing
complexity of function meson_mmc_start_cmd.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use added dev variable for devm_clk_get.
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DTS properties are used instead of fixed data
because PHY settings can be different for different chips/boards.
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add polling for ACK to be sure that data are written to PHY register.
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This fixes a NULL pointer dereference in case of a MMC request with a
set block count command and no data.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CMD23 mode (use "set block count" command before transferring multiple
data blocks) typically is more performant as host / card know upfront
how many data blocks to expect. Therefore add support for this mode to
the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently we use a fixed timeout of 4s for all data transfers. Switch
to dynamic timeout values by making use of data->timeout_ns.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
So far the driver name is used as interrupt description, therefore in
/proc/interrupts it's not possible to tell which interrupt belongs to
which port. Change this by switching to NULL what causes the default
(device name) to be used. In our case that's the DT node name.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use GENMASK consistently for all bit masks and switch to using the
bitfield macros FIELD_GET and FIELD_PREP. This hides parts of the
complexity of dealing with bit fields.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the get_timeout_clock callback doesn't clearly
have a statement that it needs the variant drivers to return
the timeout clock rate in kHz if the SDHCI_TIMEOUT_CLK_UNIT
isn't present, otherwise the variant drivers should return it
in MHz. It's also very likely that further variant drivers which
are going to use this callback will be confused by this situation.
Given the fact that moderm sdhci variant hosts are very prone to get
the timeout clock from common clock framework (actually the only three
users did that), it's more natural to return the value in Hz and we
make an explicit comment there. Then we put the unit conversion inside
the sdhci core. Thus will improve the code and prevent further misuses.
Reported-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The controller's errors are usually normal (for example, for MMC or SDIO
cards, some errors are expected to happen; and for boards without a
dedicated card detect pin the error info will even flood console and
hide other normal messages) and hard to understand.
Change their print level to debug, thus it won't be shown to generic
users.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't need variable cmd_cfg_timeout, so remove it and simplify the
code a little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Centralize setting data->bytes_xfered in one place and make sure
that the number of transfererd bytes is set only if we receive
the end-of-chain interrupt and there was no error.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Response reading can be slightly improved by doing it in just one place.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Simplify the code by using two variables instead of a struct sd_emmc_desc.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Replace cmd->data with a local variable to simplify code a little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
The variables holding the configuration bits are zero-initialized.
So we can remove all bit resets.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
If we don't select a set of better parameters for our emmc host,
It may easily occur CMD response CRC error. And also it may cause
cannot boot up issue.
Fot getting a set of better parameters, our emmc host supports
data tune mechanism.Therefore, our emmc driver also should change
to use data tune for CMD line.
Because our emmc host use the different clock source to sample the
CMD signal between HS200 and HS400 mode, the parameters are also
different between these two modes.
Separate cmd internal delay for HS200/HS400 mode.
This change can fix "System can not boot up" issue.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Improve mmc_io_rw_extended a little:
- using DIV_ROUND_UP achieves the same but is better readable
- simplify code by using sg_set_buf
- simplify one statement by using -= operator
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current code gets number of taps only once and keeps the value. This is
not correct, we need to obtain it every time before executing tuning,
so remove the outer if-block.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[wsa: extracted from a larger patch and reworded commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the (maybe academical) case, we don't get a DATAEND interrupt after
DMA completed, we will wait endlessly for the completion to complete.
This is not bad per se, since we have a more generic completion tracking
a timeout. In that rare case, however, the DMA buffer will not get
unmapped and we have a leak. Reorder the code, so unmapping will always
take place.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move a function to avoid having to forward declare it in a subsequent
patch.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The suspend / resume callbacks lack the flexibility to allow a device to
specify a different function entirely. Change them around so that device
functions are called directly and they in turn can call the default
implementations if needed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
It is confusing to have some parts of suspend / resume under conditional
compilation and some parts not. Use conditional compilation everywhere.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Do not use suspend/resume callbacks with runtime pm. It doesn't make sense
and isn't being used, so remove.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
SDHCI provides more flexibility than simply calling sdhci_add_host(). Make
that available by allowing devices to specify their own ->add_host()
function.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Add an interrupt hook and helper functions for enabling, disabling and
delivering interrupts to a CQE.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Get rid of unnecessary 'extern' in header file.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Export sdhci_dumpregs so that it can be called by drivers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Ensure all prints start with the mmc host name, and the text all lines up.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Ensure all debug prints start with the mmc host name.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Tuning execution is already synchronized with respect to other host
operations by upper layers "claiming" the host, which also takes care of
runtime pm. There can be no requests in progress. Retain the spin lock
usage only for ensuring that sending tuning commands is synchronized with
respect to the interrupt handler.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The spin lock is not necessary in set_ios. Anything that is racing with
changes to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host. So remove spin_lock and friends
from sdhci_set_ios and related callbacks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Drivers can use the host operation directly, so remove this now unused
callback.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Make use of an Intel ACPI _DSM that provides eMMC driver strength.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Make use of an Intel ACPI _DSM that indicates if re-tuning is needed after
D3.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Let devices define their own private data to facilitate device-specific
operations. The size of the private structure is specified in the
sdhci_pci_fixes structure, then sdhci_pci_probe_slot() will allocate extra
space for it, and sdhci_pci_priv() can be used to get a reference to it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Devices might save and restore tuning values so that re-tuning might not be
needed after a pm transition. Let drivers decide by pushing the
mmc_retune_needed() logic down to them.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The delay loops for reset and clock enable always take at least 1 ms
because they use mdelay(1). However they can take a lot less time e.g. less
than 50us. Use ktime and reduce the delay to 10 microseconds per loop.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The 2835 has two SD controllers: The Arasan sdhci controller (supported
by the iproc driver) and a custom sdhost controller. This patch adds a
driver for the latter.
The sdhci controller supports both sdcard and sdio. The sdhost
controller supports the sdcard only, but has better performance. Also
note that the rpi3 has sdio wifi, so driving the sdcard with the sdhost
controller allows to use the sdhci controller for wifi support.
The configuration is done by devicetree via pin muxing. Both SD
controller are available on the same pins (2 pin groups = pin 22 to 27 +
pin 48 to 53). So it's possible to use both SD controllers at the same
time with different pin groups.
The code was originally written by Phil Elwell in the downstream
Rasbperry Pi tree. In preparation for the upstream merge it was
cleaned up and the code base was moderized by Eric Anholt, Stefan
Wahren and Gerd Hoffmann.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
File contains multiple functions doing variations on the same thing,
sdio_readb(), sdio_writeb()f, sdio_readw(), sdio_writew()
etc. Although the functions have very similar logic the code is laid
out in a variety of ways. This makes it overly complicated to
read. There is a already a nice clean chunk of code, if we use this
format for all instances then we will have cleaned up the code,
reduced the line count and lessened the cognitive load required while
reading. Less lines equals less bugs.
Pick the most simple and clear code flow and change all functions to
be the same.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Various functions take as parameter an optional pointer. Pointer
should be guarded with non-NULL check before dereferencing.
Add non-NULL check before dereference of pointer.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch fixes the case where meson_mmc_probe function fails before
core_clk is enabled.
Originally, that would result in a try to disable the core clock, and if
it was not already enabled, it would result in a kernel warning.
This issue is similar to the one with div_clk.
Fix it by introducing another error path used only between successfully
enabling the core clock, and successfully enabling the div clock.
That would ensure that core clock is disabled only if it was enabled before.
Signed-off-by: Michał Zegan <webczat@webczatnet.pl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_pltfm_init() has already set the platform drvdata for us, remove
the unnecessary platform_set_drvdata() call.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_pltfm_init() has already set the platform drvdata for us, remove
the unnecessary platform_set_drvdata() call.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI controller found on NVIDIA Tegra186 SoCs is very similar to
the one on prior generations of Tegra and can be supported by the same
driver.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The device tree binding for the SDHCI controller found on Tegra SoCs
specifies that a reset control can be provided by the device tree. No
code was ever added to support the module reset, which can cause the
driver to try and access registers from a module that's in reset. On
most Tegra SoC generations doing so would cause a hang.
Note that it's unlikely to see this happen because on most platforms
these resets will have been deasserted by the bootloader. However the
portability can be improved by making sure the driver deasserts the
reset before accessing any registers.
Since resets are synchronous on Tegra SoCs, the platform driver needs
to implement a custom ->remove() callback now to make sure the clock
is disabled after the reset is asserted.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc host was added in meson_mmc_probe, but never removed in
meson_mmc_remove.
Fix that by removing the host before deallocating other resources.
Signed-off-by: Michał Zegan <webczat@webczatnet.pl>
Tested-by: Michał Zegan <webczat@webczatnet.pl>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After we received the dataend interrupt, R1 response register carries
the value from the automatically generated stop command. Report that
info back to the MMC block layer, so we will be notified in case of e.g.
ECC errors which happened during the last transfer.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Halting the kernel on an unsupported stop command seems overkill, report
the error and say what we already did (due to autocmd12) instead.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Making sure we match the actual register names.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current code assumes that DMA is finished before SD access end is
flagged. Thus, it schedules the 'dma_complete' tasklet in the SD card
interrupt routine when DATAEND is set. The assumption is not safe,
though. Even by mounting an SD card, it can be seen that sometimes DMA
complete is first, sometimes DATAEND. It seems they are usually close
enough timewise to not cause problems. However, a customer reported that
with CMD53 sometimes things really break apart. As a result, the BSP has
a patch which introduces flags for both events and makes sure both flags
are set before scheduling the tasklet. The customer accepted the patch,
yet it doesn't seem a proper upstream solution to me.
This patch refactors the code to replace the tasklet with already
existing and more lightweight mechanisms. First of all, we set the
callback in a DMA descriptor to automatically get notified when DMA is
done. In the callback, we then use a completion to make sure the SD
access has already ended. Then, we proceed as before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no check if clk_prepare_enable() succeed in sdhci_pxav2_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Struct mmc_command includes a reference to the related mmc_request.
Therefore we don't have to store mrq separately in struct meson_host.
And we can remove some now unneeded WARN_ON's.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Config values which are not changed during runtime we can set
in the probe function already.
The block size setting is overwritten later in
meson_mmc_start_cmd anyway if needed, so it doesn't harm if we
remove this setting in meson_mmc_set_ios.
In addition write config register only if configuration changed.
Don't change the location of clock initialization as in an
earlier version of the patch, this change causes a hang.
This issue was reported and fix suggested by:
Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CLK core does a deep copy of init.name, therefore it's fully ok to
provide a local variable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The condition should be "if (ret)" as the disable/unprepare is
supposed to be executed if the previous command fails.
In addition adjust the error path in probe to properly deal
with the case that cfg_div_clk can be registered successfully
but enable/prepare fails.
In this case we shouldn't call clk_disable_unprepare.
Reported-by: Michał Zegan <webczat_200@poczta.onet.pl>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Member mux_parent isn't used outside meson_mmc_clk_init. So remove it
and replace it with a local variable in meson_mmc_clk_init.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because the DT requires a fixed number of mux parent clocks,
variable mux_parent_count can be replaced with constant
MUX_CLK_NUM_PARENTS, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Member ocr_mask is never used and member irq we can replace with a
local variable in meson_mmc_probe. So let's remove both members.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The return value of meson_mmc_request_done and meson_mmc_read_resp
isn't used, so make both functions return void.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Core ensures that there are no commands with cmd->data being set and
nothing to transfer. And we don't have to reset bit CMD_CFG_DATA_NUM
because cmd_cfg was zero-initialized and this bit isn't set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Too much condition iteration makes the code
less readable. Slightly improve it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No need to declar it there, remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just use the readl_poll_timeout{_atomic} to avold open
coding them.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently for DDR50 card, it need tuning in default. We meet tuning fail
issue for DDR50 card and some data CRC error when DDR50 sd card works.
This is because the default pad I/O drive strength can't make sure DDR50
card work stable. So increase the pad I/O drive strength for DDR50 card,
and use pins_100mhz.
This fixes DDR50 card support for IMX since DDR50 tuning was enabled from
commit 9faac7b95e ("mmc: sdhci: enable tuning for DDR50")
Tested-and-reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org # v4.4+
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/mmc/host/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Pierre Ossman <pierre@ossman.eu>
cc: Ulf Hansson <ulf.hansson@linaro.org>
cc: linux-mmc@vger.kernel.org
According to the SDIO standard interrupts are normally signalled in a
very complicated way. They require the card clock to be running and
require the controller to be paying close attention to the signals
coming from the card. This simply can't happen with the clock stopped
or with the controller in a low power mode.
To that end, we'll disable runtime_pm when we detect that an SDIO card
was inserted. This is much like with what we do with the special
"SDMMC_CLKEN_LOW_PWR" bit that dw_mmc supports.
NOTE: we specifically do this Runtime PM disabling at card init time
rather than in the enable_sdio_irq() callback. This is _different_
than how SDHCI does it. Why do we do it differently?
- Unlike SDHCI, dw_mmc uses the standard sdio_irq code in Linux (AKA
dw_mmc doesn't set MMC_CAP2_SDIO_IRQ_NOTHREAD).
- Because we use the standard sdio_irq code:
- We see a constant stream of enable_sdio_irq(0) and
enable_sdio_irq(1) calls. This is because the standard code
disables interrupts while processing and re-enables them after.
- While interrupts are disabled, there's technically a period where
we could get runtime disabled while processing interrupts.
- If we are runtime disabled while processing interrupts, we'll
reset the controller at resume time (see dw_mci_runtime_resume),
which seems like a terrible idea because we could possibly have
another interrupt pending.
To fix the above isues we'd want to put something in the standard
sdio_irq code that makes sure to call pm_runtime get/put when
interrupts are being actively being processed. That's possible to do,
but it seems like a more complicated mechanism when we really just
want the runtime pm disabled always for SDIO cards given that all the
other bits needed to get Runtime PM vs. SDIO just aren't there.
NOTE: at some point in time someone might come up with a fancy way to
do SDIO interrupts and still allow (some) amount of runtime PM.
Technically we could turn off the card clock if we used an alternate
way of signaling SDIO interrupts (and out of band interrupt is one way
to do this). We probably wouldn't actually want to fully runtime
suspend in this case though--at least not with the current
dw_mci_runtime_resume() which basically fully resets the controller at
resume time.
Fixes: e9ed8835e9 ("mmc: dw_mmc: add runtime PM callback")
Cc: <stable@vger.kernel.org>
Reported-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain 64-bit systems (e.g. Amlogic Meson GX) require buffers to be
used for DMA to be 8-byte-aligned. struct sdio_func has an embedded
small DMA buffer not meeting this requirement.
When testing switching to descriptor chain mode in meson-gx driver
SDIO is broken therefore. Fix this by allocating the small DMA buffer
separately as kmalloc ensures that the returned memory area is
properly aligned for every basic data type.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc only supports discarding on large alignments, so the zeroing code
would always fall back to explicit writings of zeroes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The controller has different timings for MMC_TIMING_UHS_DDR50 and
MMC_TIMING_MMC_DDR52. Configuring the controller with SDHCI_CTRL_UHS_DDR50,
when MMC_TIMING_MMC_DDR52 timings are requested, is not correct and can
lead to unexpected behavior.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Fixes: bb5f8ea4d5 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC")
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
