CPTS module and IRQs are always enabled when CPTS is registered,
before starting overflow check work, and disabled during
deregistration, when overflow check work has been canceled already.
So, It doesn't require to (re)enable CPTS module and IRQs in
cpts_overflow_check().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a CPTS user does not exit gracefully by disabling cpts
timestamping and leaving a joined multicast group, the system
continues to receive and timestamps the ptp packets which eventually
occupy all the event list entries. When this happns, the added code
tries to remove some list entries which are expired.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpts now is left enabled after unregistration.
Hence, disable it in cpts_unregister().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ptp clock registered before spinlock, which is protecting it, and
before timecounter and cyclecounter initialization in cpts_register().
So, ensure that ptp clock is registered the last, after everything
else is done.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two issues with TI CPTS code which are reproducible when TI
CPSW ethX device passes few up/down iterations:
- cpts refclk prepare counter continuously incremented after each
up/down iteration;
- devm_clk_get(dev, "cpts") is called many times.
Hence, fix these issues by using clk_disable_unprepare() in
cpts_clk_release() and skipping devm_clk_get() if cpts refclk has been
acquired already.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will provide more flexibility in changing CPTS internals and also
required for further changes.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI CPTS IP is used as part of TI OMAP CPSW driver, but it's also
present as part of NETCP on TI Keystone 2 SoCs. So, It's required
to enable build of CPTS for both this drivers and this can be
achieved by allowing CPTS to be built separately.
Hence, allow cpts to be built separately and convert it to be
a module as both CPSW and NETCP drives can be built as modules.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to readl/writel_relaxed() APIs, because this is recommended
API and the CPTS IP is reused on Keystone 2 SoCs
where LE/BE modes are supported.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the network driver and RDMA driver operate on the same PCI function,
we need to create an interface to allow the RDMA driver to share resources
with the network driver.
1. Create a new bnxt_en_dev struct which will be returned by
bnxt_ulp_probe() upon success. After that, all calls from the RDMA driver
to bnxt_en will pass a pointer to this struct.
2. This struct contains additional function pointers to register, request
msix, send fw messages, register for async events.
3. If the RDMA driver wants to enable RDMA on the function, it needs to
call the function pointer bnxt_register_device(). A ulp_ops structure
is passed for RCU protected upcalls from bnxt_en to the RDMA driver.
4. The RDMA driver can call firmware APIs using the bnxt_send_fw_msg()
function pointer.
5. 1 stats context is reserved when the RDMA driver registers. MSIX
and completion rings are reserved when the RDMA driver calls
bnxt_request_msix() function pointer.
6. When the RDMA driver calls bnxt_unregister_device(), all RDMA resources
will be cleaned up.
v2: Fixed 2 uninitialized variable warnings.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver register function with firmware consists of passing version
information and registering for async events. To support the RDMA driver,
the async events that we need to register may change. Separate the
driver register function into 2 parts so that we can just update the
async events for the RDMA driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device supports RDMA, we'll setup network default rings so that
there are enough minimum resources for RDMA, if possible. However, the
user can still increase network rings to the max if he wants. The actual
RDMA resources won't be reserved until the RDMA driver registers.
v2: Fix compile warning when BNXT_CONFIG_SRIOV is not set.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All available remaining completion rings not used by the PF should be
made available for the VFs so that there are enough rings in the VF to
support RDMA. The earlier workaround code of capping the rings by the
statistics context is removed.
When SRIOV is disabled, call a new function bnxt_restore_pf_fw_resources()
to restore FW resources. Later on we need to add some logic to account
for RDMA resources.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that MSIX is enabled in bnxt_init_one(), resources may be allocated by
the RDMA driver before the network device is opened. So we cannot do
function reset in bnxt_open() which will clear all the resources.
The proper place to do function reset now is in bnxt_init_one().
If we get AER, we'll do function reset as well.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To better support the new RDMA driver, we need to move pci_enable_msix()
from bnxt_open() to bnxt_init_one(). This way, MSIX vectors are available
to the RDMA driver whether the network device is up or down.
Part of the existing bnxt_setup_int_mode() function is now refactored into
a new bnxt_init_int_mode(). bnxt_init_int_mode() is called during
bnxt_init_one() to enable MSIX. The remaining logic in
bnxt_setup_int_mode() to map the IRQs to the completion rings is called
during bnxt_open().
v2: Fixed compile warning when CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By refactoring existing code into this new function. The new function
will be used in subsequent patches.
v2: Fixed compile warning when CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes tun.c to call netif_receive_skb instead of netif_rx
when a packet is received (if CONFIG_4KSTACKS is not enabled to avoid
stack exhaustion). The difference between the two is that netif_rx queues
the packet into the backlog, and netif_receive_skb proccesses the packet
in the current context.
This patch is required for syzkaller [1] to collect coverage from packet
receive paths, when a packet being received through tun (syzkaller collects
coverage per process in the process context).
As mentioned by Eric this change also speeds up tun/tap. As measured by
Peter it speeds up his closed-loop single-stream tap/OVS benchmark by
about 23%, from 700k packets/second to 867k packets/second.
A similar patch was introduced back in 2010 [2, 3], but the author found
out that the patch doesn't help with the task he had in mind (for cgroups
to shape network traffic based on the original process) and decided not to
go further with it. The main concern back then was about possible stack
exhaustion with 4K stacks.
[1] https://github.com/google/syzkaller
[2] https://www.spinics.net/lists/netdev/thrd440.html#130570
[3] https://www.spinics.net/lists/netdev/msg130570.html
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more common logging style, standardize function output logging use.
Miscellanea:
o Add and use pr_fmt
o Convert printks to pr_<level>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neaten function declaration and definition arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add braces where appropriate and remove an unnecessary else.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add spaces around operators.
git diff -w shows no differences.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove leading and trailing whitespace.
git diff -w shows no differences.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the negative logic (i.e. FLUSH state), after the RQ/SQ reopen
we will have a time interval that the RQ/SQ is not really ready and the
state indicates that its not in FLUSH state because the initial SQ/RQ struct
memory starts as zeros.
Now we changed the state to indicate if the SQ/RQ is opened and we will
set the READY state after finishing preparing all the SQ/RQ resources.
Fixes: 6e8dd6d6f4 ("net/mlx5e: Don't wait for SQ completions on close")
Fixes: f2fde18c52 ("net/mlx5e: Don't wait for RQ completions on close")
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are doing SQ descriptors cleanup in driver.
Fixes: 6e8dd6d6f4 ("net/mlx5e: Don't wait for SQ completions on close")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to do this a couple of steps ahead anyway.
Fixes: d3c9bc2743 ("net/mlx5e: Added ICO SQs")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In old FWs query ISSI command is not supported and for some of those FWs
it might fail with status other than "MLX5_CMD_STAT_BAD_OP_ERR".
In such case instead of failing the driver load, we will treat any FW
status other than 0 for Query ISSI FW command as ISSI not supported and
assume ISSI=0 (most basic driver/FW interface).
In case of driver syndrom (query ISSI failure by driver) we will fail
driver load.
Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicate pci dev name printing from mlx5_core_warn/dbg.
Fixes: 5a7883989b ('net/mlx5_core: Improve mlx5 messages')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify the mlx5_core module parameters by making sure that they are in
the expected range and if they aren't restore them to their default
values.
Fixes: 9603b61de1 ('mlx5: Move pci device handling from mlx5_ib to mlx5_core')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the RX checksum function to check the
status of the hardware calculated checksum and its error and
appropriately convey status to the upper stack in skb->ip_summed
field.
In hardware, we only support checksum for the following
protocols:
1) IPv4,
2) TCP(over IPv4 or IPv6),
3) UDP(over IPv4 or IPv6),
4) SCTP(over IPv4 or IPv6)
but we support many L3(IPv4, IPv6, MPLS, PPPoE etc) and
L4(TCP, UDP, GRE, SCTP, IGMP, ICMP etc.) protocols.
Hardware limitation:
Our present hardware RX Descriptor lacks L3/L4 checksum
"Status & Error" bit (which usually can be used to indicate whether
checksum was calculated by the hardware and if there was any error
encountered during checksum calculation).
Software workaround:
We do get info within the RX descriptor about the kind of
L3/L4 protocol coming in the packet and the error status. These
errors might not just be checksum errors but could be related to
version, length of IPv4, UDP, TCP etc.
Because there is no-way of knowing if it is a L3/L4 error due
to bad checksum or any other L3/L4 error, we will not (cannot)
convey hardware checksum status(CHECKSUM_UNNECESSARY) for such
cases to upper stack and will not maintain the RX L3/L4 checksum
counters as well.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 80cca775cd ("net: fec: cache statistics while device is down")
introduced unconditional statistics-related actions.
However, when driver is compiled with CONFIG_M5272, staticsics-related
definitions do not exist, which results into build errors.
Fix that by adding explicit handling of !defined(CONFIG_M5272) case.
Fixes: 80cca775cd ("net: fec: cache statistics while device is down")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OPCODE_COMMON_GET_FN_PRIVILEGES is returning only DEVSEC
privilege (Unrestricted Administrative Privilege) for Lancer NIC functions.
So, driver is failing SET_HSW_CONFIG command, as DEVSEC privilege was not
set in the privilege bitmap. This patch fixes the problem by setting DEVSEC
privilege in SET_HSW_CONFIG’s privilege bitmap.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_VMAP_STACK=y, virtnet_set_mac_address() can be passed a
pointer to the stack and it will OOPS. Copy the address to the heap
to prevent the crash.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Laura Abbott <labbott@redhat.com>
Reported-by: zbyszek@in.waw.pl
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The budget split function requires the phy speed to be known.
While ndo open a phy speed identification is postponed till the
moment link is up. Hence, move it to appropriate callback, when link
is up.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Fixes: 8feb0a1965 ("net: ethernet: ti: cpsw: split tx budget according between channels")
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell chips can enable/disable the PPU on demand. This is needed
to access the PHY registers when there is no indirection mechanism.
Add two new ppu_enable and ppu_disable ops to describe this and finally
get rid of the MV88E6XXX_FLAG_PPU* flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell chips have different way to issue a software reset.
Old chips (such as 88E6060) have a reset bit in an ATU control register.
Newer chips moved this bit in a Global control register. Chips with
controllable PPU should reset the PPU when resetting the switch.
Add a new reset operation to implement these differences and introduce a
mv88e6xxx_software_reset() helper to wrap it conveniently.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an helper to toggle the eventual GPIO connected to the reset pin.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before resetting a switch, the ports should be set to the Disabled state
and the transmit queues should be drained.
Add an helper to explicit that.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver for Alacritech gigabit ethernet cards with SLIC (session-layer
interface control) technology. The driver provides basic support without
SLIC for the following devices:
- Mojave cards (single port PCI Gigabit) both copper and fiber
- Oasis cards (single and dual port PCI-x Gigabit) copper and fiber
- Kalahari cards (dual and quad port PCI-e Gigabit) copper and fiber
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
WR_OSR_LMT and RD_OSR_LMT have a reset value of 1.
Since the reset value wasn't cleared before writing, the value in the
register would be incorrect if specifying an uneven value for
snps,wr_osr_lmt/snps,rd_osr_lmt.
Zero is a valid value for the properties, since the databook specifies:
maximum outstanding requests = WR_OSR_LMT + 1.
We do not want to change the behavior for existing users when the
property is missing. Therefore, default to 1 if the property is missing,
since that is the same as the reset value.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add three reset control signals, "mac_core_rst", "mac_ifc_rst" and
"phy_rst".
The following diagram explained how the reset signals work.
SoC
|-----------------------------------------------------
| ------ |
| | cpu | |
| ------ |
| | |
| ------------ AMBA bus |
| GMAC | |
| ---------------------- |
| ------------- mac_core_rst | -------------- | |
| |clock and |-------------->| mac core | | |
| |reset | | -------------- | |
| |generator |---- | | | |
| ------------- | | ---------------- | |
| | ---------->| mac interface | | |
| | mac_ifc_rst | ---------------- | |
| | | | | |
| | | ------------------ | |
| |phy_rst | | RGMII interface | | |
| | | ------------------ | |
| | ---------------------- |
|----------|------------------------------------------|
| |
| ----------
|--------------------- |PHY chip |
----------
The "mac_core_rst" represents "mac core reset signal", it resets
the mac core including packet processing unit, descriptor processing unit,
tx engine, rx engine, control unit.
The "mac_ifc_rst" represents "mac interface reset signal", it resets
the mac interface. The mac interface unit connects mac core and
data interface like MII/RMII/RGMII. After we set a new value of
interface mode, we must reset mac interface to reload the new mode value.
The "mac_core_rst" and "mac_ifc_rst" are both optional to be
backward compatible with the hix5hd2 SoC.
The "phy_rst" represents "phy reset signal", it does a hardware reset
on the PHY chip. This reset signal is optional if the PHY can work well
without the hardware reset.
Add one more clock signal, the existing is MAC core clock,
and the new one is MAC interface clock.
The MAC interface clock is optional to be backward compatible with
the hix5hd2 SoC.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"hisi-gemac-v2" adds the SG/TXCSUM/TSO/UFO features.
This patch only adds the SG(scatter-gather) driver for transmitting,
the drivers of other features will be submitted later.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "hix5hd2" is SoC name, add the generic ethernet driver name.
The "hisi-gemac-v1" is the basic version and "hisi-gemac-v2" adds
the SG/TXCSUM/TSO/UFO features.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DSA_TAG_PROTO_EDSA as tag_protocol for the mv88e6097. The
initialisation was missing before.
Fixes: a1f482aa8c33 ("net: dsa: mv88e6xxx: Move the tagging protocol into info")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we unload the ep93xx_eth, whether we have opened the network
interface or not, we will either hit a kernel paging request error, or a
simple NULL pointer de-reference because:
- if ep93xx_open has been called, we have created a valid DMA mapping
for ep->descs, when we call ep93xx_stop, we also call
ep93xx_free_buffers, ep->descs now has a stale value
- if ep93xx_open has not been called, we have a NULL pointer for
ep->descs, so performing any operation against that address just won't
work
Fix this by adding a NULL pointer check for ep->descs which means that
ep93xx_free_buffers() was able to successfully tear down the descriptors
and free the DMA cookie as well.
Fixes: 1d22e05df8 ("[PATCH] Cirrus Logic ep93xx ethernet driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spamming the console with: net eth1: packet dropped can happen
fairly frequently if the adapter is busy transmitting, demote the
message to a debug print.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address() which
looks up the MAC address using the 3 typical property names.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethoc_mdio_poll() which is our PHYLIB adjust_link callback does nothing,
we should at least react to duplex changes and change MODER accordingly.
Speed changes is not a problem, since the OpenCores Ethernet core seems
to be reacting okay without us telling it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
