Prior to commit 6800234cee ("drm/vc4: hdmi: Convert to gpiod"), in the
detect hook, if we had an HPD GPIO we would only rely on it and return
whatever state it was in.
However, that commit changed that by mistake to only consider the case
where we have a GPIO and it returns a logical high, and would fall back
to the other methods otherwise.
Since we can read the EDIDs when the HPD signal is low on some displays,
we changed the detection status from disconnected to connected, and we
would ignore an HPD pulse.
Fixes: 6800234cee ("drm/vc4: hdmi: Convert to gpiod")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-3-maxime@cerno.tech
Commit 9d44abbbb8 ("drm/vc4: Fall back to using an EDID probe in the
absence of a GPIO.") added some code to read the EDID through DDC in the
HDMI driver detect hook since the Pi3 had no HPD GPIO back then.
However, commit b1b8f45b31 ("ARM: dts: bcm2837: Add missing GPIOs of
Expander") changed that a couple of years later.
This causes an issue though since some TV (like the LG 55C8) when it
comes out of standy will deassert the HPD line, but the EDID will
remain readable.
It causes an issues nn platforms without an HPD GPIO, like the Pi4,
where the DDC probing will be our primary mean to detect a display, and
thus we will never detect the HPD pulse. This was fine before since the
pulse was small enough that we would never detect it, and we also didn't
have anything (like the scrambler) that needed to be set up in the
display.
However, now that we have both, the display during the HPD pulse will
clear its scrambler status, and since we won't detect the
disconnect/reconnect cycle we will never enable the scrambler back.
As our main reason for that DDC probing is gone, let's just remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-2-maxime@cerno.tech
Define helpers and struct members required to record boost info.
Boost frequency is initialized to RP0 at SLPC init. Also define num_waiters
which can track the pending boost requests.
Boost will be done by scheduling a worker thread. This will avoid
the need to make H2G calls inside an interrupt context. Initialize the
worker function during SLPC init as well. Had to move intel_guc_slpc_init
a few lines below to accommodate this.
v2: Add a workqueue to handle waitboost
v3: Code review comments (Ashutosh)
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211102012608.8609-2-vinay.belgaumkar@intel.com
Pull ARM SoC driver updates from Arnd Bergmann:
"These are all the driver updates for SoC specific drivers. There are a
couple of subsystems with individual maintainers picking up their
patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this tree this
time. There are only minor changes, but they depend on other tegra
driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process. This
depends on a small sound driver change that is included here as
well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains a
mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for the
"Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed BMCs,
something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better
suspend/resume support"
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx,
layerscape, allwinner, broadcom, and omap"
* tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (179 commits)
optee: Fix spelling mistake "reclain" -> "reclaim"
Revert "firmware: qcom: scm: Add support for MC boot address API"
qcom: spm: allow compile-testing
firmware: arm_ffa: Remove unused 'compat_version' variable
soc: samsung: exynos-chipid: add exynosautov9 SoC support
firmware: qcom: scm: Don't break compile test on non-ARM platforms
soc: qcom: smp2p: Add of_node_put() before goto
soc: qcom: apr: Add of_node_put() before return
soc: qcom: qcom_stats: Fix client votes offset
soc: qcom: rpmhpd: fix sm8350_mxc's peer domain
dt-bindings: arm: cpus: Document qcom,msm8916-smp enable-method
ARM: qcom: Add qcom,msm8916-smp enable-method identical to MSM8226
firmware: qcom: scm: Add support for MC boot address API
soc: qcom: spm: Add 8916 SPM register data
dt-bindings: soc: qcom: spm: Document qcom,msm8916-saw2-v3.0-cpu
soc: qcom: socinfo: Add PM8150C and SMB2351 models
firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available()
soc: aspeed: Add UART routing support
soc: fsl: dpio: rename the enqueue descriptor variable
soc: fsl: dpio: use an explicit NULL instead of 0
...
The code which constructs the modules for each engine present on the GPU
passes -1 for 'instance' on non-instanced engines, which affects how the
name for a sub-device is generated. This is then stored as 'instance 0'
in nvkm_subdev.inst, so code can potentially be shared with earlier GPUs
that only had a single instance of an engine.
However, GF100's CE constructor uses this value to calculate the address
of its falcon before it's translated, resulting in CE0 getting the wrong
address.
This slightly modifies the approach, always passing a valid instance for
engines that *can* have multiple copies, and having the code for earlier
GPUs explicitly ask for non-instanced name generation.
Bug: https://gitlab.freedesktop.org/drm/nouveau/-/issues/91
Fixes: 50551b15c7 ("drm/nouveau/ce: switch to instanced constructor")
Cc: <stable@vger.kernel.org> # v5.12+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Tested-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211103011057.15344-1-skeggsb@gmail.com
[Why]
During Z10, root clock gating and memory low power registers needs to
to be restored if optimization is enabled in driver.
[How]
Added new DMUB boot option for root clock gating and memory low power.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPO is only used for DP2.0. HPO HW control should be
disable when not being used to save power.
[How]
Shutdown HPO HW control during init hw.
Shutdown HPO HW control during stream disable.
Enable HPO HW control during stream enable if DP2.0.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
State can be cleared without removing individual streams (by
calling dc_remove_stream_from_ctx()). This can leave the
encoder assignment module in an incoherent state and cause
future assignments to be incorrect.
[How]
Clear encoder assignments when committing 0 streams or
re-initializing hardware.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In scenario when 1 display connected with pipe split (2 pipes in use)
and 3 new displays simultaneously hotplugged via MST hub (4 pipes in use),
mpcc may get reprogram to other vtg, remaining busy.
In this case waiting for mpcc idle timeouts with error like this:
[drm] REG_WAIT timeout 1us * 100000 tries - mpc2_assert_idle_mpcc
RIP: 0010:mpc2_assert_mpcc_idle_before_connect
Call Trace:
dcn20_update_mpcc
dcn20_program_front_end_for_ctx
dc_commit_state
amdgpu_dm_atomic_commit_tail
...
[How]
Add pipe split change condition to disable dangling plane.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
It was found that the system would hang on a dummy pstate when playing
4k60 videos on a 1080p 390Hz monitor.
[HOW]
Properly select the dummy_pstate_latency_ms when firmware assisted
memory clock switching is enabled instead of assuming that the highest
latency would work for every monitor timing.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Felipe Clark <felclark@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
If timing and bpp of displays on mst hub are not changed,
pbn, slot_num for displays should not be changed. Linux
user mode may initiate atomic_check with different display
configuration after set mode finished. This will call to
amdgpu_dm to re-compute payload, slot_num of displays and
saved to dm_connect_state. stream->timing.flags.dsc, pbn,
slot_num are updated to values which may be different from
that were used for set mode. when dsc hub with 3 4k@60hz dp
connected, 3 dsc engines are enabled. timing.flags.dsc = 1.
timing.flags.dsc are changed to 0 due to atomic check. when
dsc hub is unplugged, amdgpu driver check timing.flags.dsc
for last mode set and find out flags.dsc = 0, then does not
disable dsc.
[HOW]
check status of displays on dsc mst hubs. re-compute pbn,
slot_num, timing.flags.dsc only if there is mode, connect
or enable/disable change.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Hersen Wu <hersenwu@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This better aligns that the caller can make a mistake with the buffer
and -EINVAL should be returned, but if the hardware doesn't support
the feature it should be -EOPNOTSUPP.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was added by commit bd8dcea93a ("drm/amd/pm: add callbacks to
read/write sysfs file pp_power_profile_mode") but the feature was
deprecated from PMFW. Remove it from the driver.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previously Renoir compiler gfx target version was forced to Raven.
Update driver side for completeness.
Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is more useful when talking to the SMU team to have the information
in this format, save one less step to manually do it.
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If some pages fail to migrate to system memory, don't update
prange->actual_loc = 0. This prevents endless CPU page faults after
partial migration failures due to contested page locks.
Migration to RAM must be complete during migrations from VRAM to VRAM and
during evictions. Implement retry and fail if the migration to RAM fails.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stack and heap pages tend to be shared by many small allocations.
Concurrent access by CPU and GPU is therefore likely, which can lead to
thrashing. Avoid this by setting the preferred location to system memory.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The preferred location should be used as the migration destination
whenever it is accessible by the faulting GPU. System memory is always
accessible. Peer memory is accessible if it's in the same XGMI hive.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Aldebaran has different register mask definitions for
regiter MC_VM_XGMI_LFB_CNTL. Use the correct masks
to interpret fields of this register.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In advance tdr mode, the real bad job will be resubmitted twice, while
in drm_sched_resubmit_jobs_ext, there's a dma_fence_put, so the bad job
is put one more time than other jobs.
[How]
Adding dma_fence_get before resbumit job in
amdgpu_device_recheck_guilty_jobs and put the fence for normal jobs
Signed-off-by: Jingwen Chen <Jingwen.Chen2@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull drm updates from Dave Airlie:
"Summary below. i915 starts to add support for DG2 GPUs, enables DG1
and ADL-S support by default, lots of work to enable DisplayPort 2.0
across drivers. Lots of documentation updates and fixes across the
board.
core:
- improve dma_fence, lease and resv documentation
- shmem-helpers: allocate WC pages on x86, use vmf_insert_pin
- sched fixes/improvements
- allow empty drm leases
- add dma resv iterator
- add more DP 2.0 headers
- DP MST helper improvements for DP2.0
dma-buf:
- avoid warnings, remove fence trace macros
bridge:
- new helper to get rid of panels
- probe improvements for it66121
- enable DSI EOTP for anx7625
fbdev:
- efifb: release runtime PM on destroy
ttm:
- kerneldoc switch
- helper to clear all DMA mappings
- pool shrinker optimizaton
- remove ttm_tt_destroy_common
- update ttm_move_memcpy for async use
panel:
- add new panel-edp driver
amdgpu:
- Initial DP 2.0 support
- Initial USB4 DP tunnelling support
- Aldebaran MCE support
- Modifier support for DCC image stores for GFX 10.3
- Display rework for better FP code handling
- Yellow Carp/Cyan Skillfish updates
- Cyan Skillfish display support
- convert vega/navi to IP discovery asic enumeration
- validate IP discovery table
- RAS improvements
- Lots of fixes
i915:
- DG1 PCI IDs + LMEM discovery/placement
- DG1 GuC submission by default
- ADL-S PCI IDs updated + enabled by default
- ADL-P (XE_LPD) fixed and updates
- DG2 display fixes
- PXP protected object support for Gen12 integrated
- expose multi-LRC submission interface for GuC
- export logical engine instance to user
- Disable engine bonding on Gen12+
- PSR cleanup
- PSR2 selective fetch by default
- DP 2.0 prep work
- VESA vendor block + MSO use of it
- FBC refactor
- try again to fix fast-narrow vs slow-wide eDP training
- use THP when IOMMU enabled
- LMEM backup/restore for suspend/resume
- locking simplification
- GuC major reworking
- async flip VT-D workaround changes
- DP link training improvements
- misc display refactorings
bochs:
- new PCI ID
rcar-du:
- Non-contiguious buffer import support for rcar-du
- r8a779a0 support prep
omapdrm:
- COMPILE_TEST fixes
sti:
- COMPILE_TEST fixes
msm:
- fence ordering improvements
- eDP support in DP sub-driver
- dpu irq handling cleanup
- CRC support for making igt happy
- NO_CONNECTOR bridge support
- dsi: 14nm phy support for msm8953
- mdp5: msm8x53, sdm450, sdm632 support
stm:
- layer alpha + zpo support
v3d:
- fix Vulkan CTS failure
- support multiple sync objects
gud:
- add R8/RGB332/RGB888 pixel formats
vc4:
- convert to new bridge helpers
vgem:
- use shmem helpers
virtio:
- support mapping exported vram
zte:
- remove obsolete driver
rockchip:
- use bridge attach no connector for LVDS/RGB"
* tag 'drm-next-2021-11-03' of git://anongit.freedesktop.org/drm/drm: (1259 commits)
drm/amdgpu/gmc6: fix DMA mask from 44 to 40 bits
drm/amd/display: MST support for DPIA
drm/amdgpu: Fix even more out of bound writes from debugfs
drm/amdgpu/discovery: add SDMA IP instance info for soc15 parts
drm/amdgpu/discovery: add UVD/VCN IP instance info for soc15 parts
drm/amdgpu/UAPI: rearrange header to better align related items
drm/amd/display: Enable dpia in dmub only for DCN31 B0
drm/amd/display: Fix USB4 hot plug crash issue
drm/amd/display: Fix deadlock when falling back to v2 from v3
drm/amd/display: Fallback to clocks which meet requested voltage on DCN31
drm/amd/display: move FPU associated DCN301 code to DML folder
drm/amd/display: fix link training regression for 1 or 2 lane
drm/amd/display: add two lane settings training options
drm/amd/display: decouple hw_lane_settings from dpcd_lane_settings
drm/amd/display: implement decide lane settings
drm/amd/display: adopt DP2.0 LT SCR revision 8
drm/amd/display: FEC configuration for dpia links in MST mode
drm/amd/display: FEC configuration for dpia links
drm/amd/display: Add workaround flag for EDID read on certain docks
drm/amd/display: Set phy_mux_sel bit in dmub scratch register
...
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to the most recent upstream
revision, address some issues related to the ACPI power resources
management, simplify the enumeration of PCI devices having ACPI
companions, add new quirks, fix assorted problems, update the
ACPI-related information in maintainers and clean up code in several
places.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20210930
including the following changes:
- Fix system-wide resume issue caused by evaluating control
methods too early in the resume path (Rafael Wysocki).
- Add support for Windows 2020 _OSI string (Mario Limonciello).
- Add Generic Port Affinity type for SRAT (Alison Schofield).
- Add disassembly support for the NHLT ACPI table (Bob Moore).
- Avoid flushing caches before entering C3 type of idle states on AMD
processors (Deepak Sharma).
- Avoid enumerating CPUs that are not present and not online-capable
according to the platform firmware (Mario Limonciello).
- Add DMI-based mechanism to quirk IRQ overrides and use it for two
platforms (Hui Wang).
- Change the configuration of unused ACPI device objects to reflect
the D3cold power state after enumerating devices (Rafael Wysocki).
- Update MAINTAINERS information regarding ACPI (Rafael Wysocki).
- Fix typo in ACPI Kconfig (Masanari Iid).
- Use sysfs_emit() instead of snprintf() in some places (Qing Wang).
- Make the association of ACPI device objects with PCI devices more
straightforward and simplify the code doing that for all devices in
general (Rafael Wysocki).
- Use acpi_device_adr() in acpi_find_child_device() instead of
evaluating _ADR (Rafael Wysocki).
- Drop duplicate device IDs from PNP device IDs list (Krzysztof
Kozlowski).
- Allow acpi_idle_play_dead() to use C3 on AMD processors (Richard
Gong).
- Use ACPI_COMPANION() to simplify code in some drivers (Rafael
Wysocki).
- Check the states of all ACPI power resources during initialization
to avoid dealing with power resources in unknown states (Rafael
Wysocki).
- Fix ACPI power resource issues related to sharing wakeup power
resources (Rafael Wysocki).
- Avoid registering redundant suspend_ops (Rafael Wysocki).
- Report battery charging state as "full" if it appears to be over
the design capacity (André Almeida).
- Quirk GK45 mini PC to skip reading _PSR in the AC driver (Stefan
Schaeckeler).
- Mark apei_hest_parse() static (Christoph Hellwig).
- Relax platform response timeout to 1 second after instructing it to
inject an error (Shuai Xue).
- Make the PRM code handle memory allocation and remapping failures
more gracefully and drop some unnecessary blank lines from that
code (Aubrey Li).
- Fix spelling mistake in the ACPI documentation (Colin Ian King)"
* tag 'acpi-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (36 commits)
ACPI: glue: Use acpi_device_adr() in acpi_find_child_device()
perf: qcom_l2_pmu: ACPI: Use ACPI_COMPANION() directly
ACPI: APEI: mark apei_hest_parse() static
ACPI: APEI: EINJ: Relax platform response timeout to 1 second
gpio-amdpt: ACPI: Use the ACPI_COMPANION() macro directly
nouveau: ACPI: Use the ACPI_COMPANION() macro directly
ACPI: resources: Add one more Medion model in IRQ override quirk
ACPI: AC: Quirk GK45 to skip reading _PSR
ACPI: PM: sleep: Do not set suspend_ops unnecessarily
ACPI: PRM: Handle memory allocation and memory remap failure
ACPI: PRM: Remove unnecessary blank lines
ACPI: PM: Turn off wakeup power resources on _DSW/_PSW errors
ACPI: PM: Fix sharing of wakeup power resources
ACPI: PM: Turn off unused wakeup power resources
ACPI: PM: Check states of power resources during initialization
ACPI: replace snprintf() in "show" functions with sysfs_emit()
ACPI: LPSS: Use ACPI_COMPANION() directly
ACPI: scan: Release PM resources blocked by unused objects
ACPI: battery: Accept charges over the design capacity as full
ACPICA: Update version to 20210930
...
Pull gfs2 mmap + page fault deadlocks fixes from Andreas Gruenbacher:
"Functions gfs2_file_read_iter and gfs2_file_write_iter are both
accessing the user buffer to write to or read from while holding the
inode glock.
In the most basic deadlock scenario, that buffer will not be resident
and it will be mapped to the same file. Accessing the buffer will
trigger a page fault, and gfs2 will deadlock trying to take the same
inode glock again while trying to handle that fault.
Fix that and similar, more complex scenarios by disabling page faults
while accessing user buffers. To make this work, introduce a small
amount of new infrastructure and fix some bugs that didn't trigger so
far, with page faults enabled"
* tag 'gfs2-v5.15-rc5-mmap-fault' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Fix mmap + page fault deadlocks for direct I/O
iov_iter: Introduce nofault flag to disable page faults
gup: Introduce FOLL_NOFAULT flag to disable page faults
iomap: Add done_before argument to iomap_dio_rw
iomap: Support partial direct I/O on user copy failures
iomap: Fix iomap_dio_rw return value for user copies
gfs2: Fix mmap + page fault deadlocks for buffered I/O
gfs2: Eliminate ip->i_gh
gfs2: Move the inode glock locking to gfs2_file_buffered_write
gfs2: Introduce flag for glock holder auto-demotion
gfs2: Clean up function may_grant
gfs2: Add wrapper for iomap_file_buffered_write
iov_iter: Introduce fault_in_iov_iter_writeable
iov_iter: Turn iov_iter_fault_in_readable into fault_in_iov_iter_readable
gup: Turn fault_in_pages_{readable,writeable} into fault_in_{readable,writeable}
powerpc/kvm: Fix kvm_use_magic_page
iov_iter: Fix iov_iter_get_pages{,_alloc} page fault return value
Pull KVM updates from Paolo Bonzini:
"ARM:
- More progress on the protected VM front, now with the full fixed
feature set as well as the limitation of some hypercalls after
initialisation.
- Cleanup of the RAZ/WI sysreg handling, which was pointlessly
complicated
- Fixes for the vgic placement in the IPA space, together with a
bunch of selftests
- More memcg accounting of the memory allocated on behalf of a guest
- Timer and vgic selftests
- Workarounds for the Apple M1 broken vgic implementation
- KConfig cleanups
- New kvmarm.mode=none option, for those who really dislike us
RISC-V:
- New KVM port.
x86:
- New API to control TSC offset from userspace
- TSC scaling for nested hypervisors on SVM
- Switch masterclock protection from raw_spin_lock to seqcount
- Clean up function prototypes in the page fault code and avoid
repeated memslot lookups
- Convey the exit reason to userspace on emulation failure
- Configure time between NX page recovery iterations
- Expose Predictive Store Forwarding Disable CPUID leaf
- Allocate page tracking data structures lazily (if the i915 KVM-GT
functionality is not compiled in)
- Cleanups, fixes and optimizations for the shadow MMU code
s390:
- SIGP Fixes
- initial preparations for lazy destroy of secure VMs
- storage key improvements/fixes
- Log the guest CPNC
Starting from this release, KVM-PPC patches will come from Michael
Ellerman's PPC tree"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (227 commits)
RISC-V: KVM: fix boolreturn.cocci warnings
RISC-V: KVM: remove unneeded semicolon
RISC-V: KVM: Fix GPA passed to __kvm_riscv_hfence_gvma_xyz() functions
RISC-V: KVM: Factor-out FP virtualization into separate sources
KVM: s390: add debug statement for diag 318 CPNC data
KVM: s390: pv: properly handle page flags for protected guests
KVM: s390: Fix handle_sske page fault handling
KVM: x86: SGX must obey the KVM_INTERNAL_ERROR_EMULATION protocol
KVM: x86: On emulation failure, convey the exit reason, etc. to userspace
KVM: x86: Get exit_reason as part of kvm_x86_ops.get_exit_info
KVM: x86: Clarify the kvm_run.emulation_failure structure layout
KVM: s390: Add a routine for setting userspace CPU state
KVM: s390: Simplify SIGP Set Arch handling
KVM: s390: pv: avoid stalls when making pages secure
KVM: s390: pv: avoid stalls for kvm_s390_pv_init_vm
KVM: s390: pv: avoid double free of sida page
KVM: s390: pv: add macros for UVC CC values
s390/mm: optimize reset_guest_reference_bit()
s390/mm: optimize set_guest_storage_key()
s390/mm: no need for pte_alloc_map_lock() if we know the pmd is present
...
