This patch simply adds a new DMATYPE for SAI which's included
in i.MX6 Solo X.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes a race condition about a list of shdma-base driver.
If we don't apply this patch, a dma slave driver (especially a usb
peripheral driver) may not be able to start the transfer.
If a dma slave driver has a callback, __ld_cleanup() will call
the callback before this driver removes the list. After the callback,
since the return value of __ld_cleanup() is not zero,
shdma_chan_ld_cleanup() calls __ld_cleanup() again. And, __ld_clean()
will removes the list.
At this time, if a dma slave driver calls dmaengine_submit() before
this driver removes the list, this driver will set schan->pm_state
to SHDMA_PM_PENDING in shdma_tx_submit(). And then, even if a dma
slave driver calls dma_async_issue_pending(), this driver don't
start the transfer because the schan->pm_state is SHDMA_PM_PENDING
in shdma_issue_pending().
So, this patch adds a new condition in __ld_clean() to check if the
schan->pm_state is SHDMA_PM_PENDING or not.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We currently have register offset information only for BAM IPs with revision
1.4.0. We add register offset table entries for the legacy (v1.3.0) version
of BAM IPs found on SoCs like APQ8064 and MSM8960.
The register offset table pointers are stored in DT data corresponding to the
BAM IP version specified in the compatible string.
Reviewed-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The BAM DMA IP comes in different versions. The register offset layout varies
among these versions. The layouts depend on which generation/family of SoCs they
belong to.
The current SoCs(like 8084, 8074) have a layout where the Top level registers
come in the beginning of the address range, followed by pipe and event
registers. The BAM revision numbers fall above 1.4.0.
The older SoCs (like 8064, 8960) have a layout where the pipe registers come
first, and the top level come later. These have BAM revision numbers lesser than
1.4.0.
It isn't suitable to have macros provide the register offsets with the layouts
changed. Future BAM revisions may have different register layouts too. The
register addresses are now calculated by referring a table which contains a base
offset and multipliers for pipe/evnt/ee registers.
We have a common function bam_addr() which computes addresses for all the
registers. When computing address of top level/ee registers, we pass 0 to the
pipe argument in addr() since they don't have any multiple instances.
Some of the unused register definitions are removed. We can add new registers as
we need them.
Reviewed-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The A23 SoC has the same dma engine as the A31 (sun6i), with a
reduced amount of endpoints and physical channels. Add the proper
config data and compatible string to support it.
A slight difference in sun8i is an undocumented register needs
to be toggled for dma to function.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for hardware parameters tied to compatible
strings, so similar hardware can reuse the driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When platform_driver_probe() is not used, sdma_probe() can be called
by bind/unbind via sysfs. In addition, sdma_init() can be called by
sdma_probe(). Thus, __init annotation should be removed from sdma_init(),
Also, this patch fixes section mismatch warning.
WARNING: drivers/dma/built-in.o(.text+0xd6e4): Section mismatch in reference from the function sdma_probe() to the function
.init.text:sdma_init()
The function sdma_probe() references
the function __init sdma_init().
This is often because sdma_probe lacks a __init
annotation or the annotation of sdma_init is wrong.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit f6f2421c0a removed pl330_info structure by embedding it into
pl330_dmac structure, but did not ensure that the dmac->ddma.dev
pointer gets initialised before use. When dma_alloc_coherent() gets
called on arm64 a WARN() gets triggered due to dev being NULL.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1 at arch/arm64/mm/dma-mapping.c:49 __dma_alloc_coherent+0xd0/0xe0()
Use an actual device structure for DMA allocation
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.17.0+ #5
Call trace:
[<ffffffc000087f24>] dump_backtrace+0x0/0x130
[<ffffffc000088064>] show_stack+0x10/0x1c
[<ffffffc0004e8af8>] dump_stack+0x74/0xb8
[<ffffffc0000aa444>] warn_slowpath_common+0x8c/0xb4
[<ffffffc0000aa4b8>] warn_slowpath_fmt+0x4c/0x58
[<ffffffc000092580>] __dma_alloc_coherent+0xcc/0xe0
[<ffffffc000092734>] __dma_alloc_noncoherent+0x64/0x158
[<ffffffc000312cd8>] pl330_probe+0x650/0x8f0
[<ffffffc00030e1d4>] amba_probe+0xa0/0xc8
[<ffffffc000350240>] really_probe+0xc4/0x22c
[<ffffffc0003504b4>] __driver_attach+0xa0/0xa8
[<ffffffc00034e5fc>] bus_for_each_dev+0x54/0x98
[<ffffffc00034fd8c>] driver_attach+0x1c/0x28
[<ffffffc00034fa08>] bus_add_driver+0x14c/0x204
[<ffffffc000350b84>] driver_register+0x64/0x130
[<ffffffc00030dcf8>] amba_driver_register+0x50/0x5c
[<ffffffc0006a60d0>] pl330_driver_init+0x10/0x1c
[<ffffffc0000814ac>] do_one_initcall+0x88/0x19c
[<ffffffc00068dab8>] kernel_init_freeable+0x140/0x1e0
[<ffffffc0004e5e18>] kernel_init+0x10/0xd4
---[ end trace 76f2d47a444e523e ]---
(NULL device *): dmac_alloc_resources:1821 Can't allocate memory!
(NULL device *): Unable to create channels for DMAC
This patch will also ensure that any dev_err messages are printed
with the appropriate device name.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch modifies the icg field to match the description
as mentioned in the DMA Linux framework.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds a sanity check to see if frame_size is 1.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The segment list in a descriptor should be checked for empty, else
it will try to access invalid address for the first call. This
patch fixes this issue.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
[for nvidia]
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
New atmel DMA controller known as XDMAC, introduced with SAMA5D4
devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
The freescale driver uses custom device control FSLDMA_EXTERNAL_START to
put the controller in external start mode.
Since we are planning to deprecate the device control, move this to exported
API. Subsequent patches will remove the FSLDMA_EXTERNAL_START
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The drivers should use dmaengine_terminate_all() API instead of accessing
the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
I added book keeping of whether or not the 8250-dma driver has an RX
transfer pending or not so we don't BUG here if it calls
dmaengine_pause() on a channel which has not a pending transfer. Guess
what, this is not enough.
The following can be triggered with a busy RX channel and hackbench in
background:
- DMA transfer completes. The callback is delayed via
vchan_cookie_complete() into a tasklet so it das not happen asap.
- hackbench keeps the system busy so the tasklet does not run "soon".
- the UART collected enough data and generates an "timeout"-interrupt.
Since 8250-dma *thinks* the DMA-transfer is still pending it tries to
cancel it via invoking dmaengine_pause() first. This causes the segfault
because echan->edesc is NULL now that the transfer completed (however
the callback did not run yet).
With this patch we don't BUG in the scenario described.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The driver library functions can be used directly by the compound devices such
as ADSP or serial driver where DesignWare DMA IP is privately attached to the
main hardware.
Instead of creating a new platform device leaf they may call dw_dma_probe()
with given struct dw_dma_chip directly and make sure that the main device is
DMA capable.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Enable controller automatically whenever first user requires for a channel and
disable it when the last user gone.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of conditional exporing of dw_dma_suspend() / dw_dma_resume() let's
export dw_dma_disable() / dw_dma_enable(). Since dw_dma_shutdown() repeats
dw_dma_disable() we may safely remove it at all.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As an opposite to dw_dma_off() let's introduce dw_dma_on() helper. It will be
useful later as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The introduced include/linux/dma/dw.h is going to contain the private
extensions and structures which are shared for dw_dmac users in the kernel.
Meanwhile include/linux/platform_data/dma-dw.h keeps only platform related data
types and definitions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since we don't allow user to set registers directly through private slave
configuration we may move definitions to the regs.h because they are not used
anywhere except core.c part.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This change uses managed resource APIs to allocate resources such as,
mem, irq in order to simplify the driver unload or failure cases
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The 'void __iomem *regs' is not used in pl330_submit_req() function.
Remove it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pl330_submit_req() checked supplied 'struct pl330_thread thrd' and
'struct dma_pl330_desc desc' parameters for non-NULL. However these
checks are useless because supplied arguments won't be NULL.
The pl330_submit_req() is called in only one place and:
1. 'desc' is already dereferenced in fill_queue() before calling
pl330_submit_req().
2. 'thrd' is always dereferenced after calling
fill_queue()->pl330_submit_req().
Removing the checks for non-NULL values fixes following warning:
drivers/dma/pl330.c:1376 pl330_submit_req() warn: variable dereferenced before check 'thrd' (see line 1367)
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
1/ Step down as dmaengine maintainer see commit 08223d80df "dmaengine
maintainer update"
2/ Removal of net_dma, as it has been marked 'broken' since 3.13 (commit
7787380336 "net_dma: mark broken"), without reports of performance
regression.
3/ Miscellaneous fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BBBv
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine updates from Dan Williams:
"Even though this has fixes marked for -stable, given the size and the
needed conflict resolutions this is 3.18-rc1/merge-window material.
These patches have been languishing in my tree for a long while. The
fact that I do not have the time to do proper/prompt maintenance of
this tree is a primary factor in the decision to step down as
dmaengine maintainer. That and the fact that the bulk of drivers/dma/
activity is going through Vinod these days.
The net_dma removal has not been in -next. It has developed simple
conflicts against mainline and net-next (for-3.18).
Continuing thanks to Vinod for staying on top of drivers/dma/.
Summary:
1/ Step down as dmaengine maintainer see commit 08223d80df
"dmaengine maintainer update"
2/ Removal of net_dma, as it has been marked 'broken' since 3.13
(commit 7787380336 "net_dma: mark broken"), without reports of
performance regression.
3/ Miscellaneous fixes"
* tag 'dmaengine-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
net: make tcp_cleanup_rbuf private
net_dma: revert 'copied_early'
net_dma: simple removal
dmaengine maintainer update
dmatest: prevent memory leakage on error path in thread
ioat: Use time_before_jiffies()
dmaengine: fix xor sources continuation
dma: mv_xor: Rename __mv_xor_slot_cleanup() to mv_xor_slot_cleanup()
dma: mv_xor: Remove all callers of mv_xor_slot_cleanup()
dma: mv_xor: Remove unneeded mv_xor_clean_completed_slots() call
ioat: Use pci_enable_msix_exact() instead of pci_enable_msix()
drivers: dma: Include appropriate header file in dca.c
drivers: dma: Mark functions as static in dma_v3.c
dma: mv_xor: Add DMA API error checks
ioat/dca: Use dev_is_pci() to check whether it is pci device
In e34b731faa ("dma: imx-sdma: Remove spurious __init annotation on
sdma_probe()"), Mark found an extraneous __init label and fixed it.
However, he missed another one, because now we get this other warning:
WARNING: drivers/dma/imx-sdma.o(.text+0x3bb4): Section mismatch in reference from the function sdma_probe() to the function .init.text:sdma_get_firmware()
The function sdma_probe() references
the function __init sdma_get_firmware().
Same reasoning as the last time, the function may get called at
runtime, so it can't be __init.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Per commit "77873803363c net_dma: mark broken" net_dma is no longer used
and there is no plan to fix it.
This is the mechanical removal of bits in CONFIG_NET_DMA ifdef guards.
Reverting the remainder of the net_dma induced changes is deferred to
subsequent patches.
Marked for stable due to Roman's report of a memory leak in
dma_pin_iovec_pages():
https://lkml.org/lkml/2014/9/3/177
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: David Whipple <whipple@securedatainnovations.ch>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: <stable@vger.kernel.org>
Reported-by: Roman Gushchin <klamm@yandex-team.ru>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The sun6i DMA controller requires the AHB1 bus clock to be
clocked from PLL6. This was originally done by the dmaengine
driver during probe time. The AHB1 clock driver has since been
unified, so the original code does not work.
Remove the clk muxing code, and replace it with DT clk default
properties.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
MX6 processors also use the IMX_SDMA driver, so include it in the help text.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When we fail to allocate memory for thread->srcs or thread->dsts and src_cnt or
dst_cnt great than 1 we leak memory on error path. This patch fixes the issue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The driver is capable of supporting DMA_INTERRUPT by issuing a dummy 128-byte
transfer. This helps removing a poll in the async_tx stack, replacing it with
a completion interrupt.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The driver currently defines the USE_TIMER macro, but the timer-feature
is never used in the code. The XOR and CRC32 results are never used.
The 'unmap_xxx' fields are no longer needed, they were made obsolete
in commit: 54f8d501e8 dmaengine: remove DMA unmap from drivers.
Let's remove all this dead code.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
