The attached patch fix VBI support cx88 card.
I'm running a capture for hours, getting the closed caption from it[1], and
it's working perfect - the output is the same of a bttv card.
Please apply this patch as soon as possible.
[1] - using zvbi-ntsc-cc of zvbi project.
Signed-off-by: Rafael Diniz <diniz@wimobilis.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
config\tDVB_USB_CINERGY_T2 causes the make_kconfig.pl to forget to enable by default the compilation of cinergyT2 module.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There already is an report at kernel bugzilla about this issue:
http://bugzilla.kernel.org/show_bug.cgi?id=9455
When enabling extra checks for the i2c-bus of cx88 based cards by
loading i2c_algo_bit with bit_test=1 this may trigger an oops
when loading cx88_dvb.
This is caused by the extra check code that detects that the
sda-line is stuck high and thus does not register the i2c-bus.
cx88-dvb however does not check if the i2c-bus is valid and just
uses core->i2c_adap to attach dvb frontend modules.
This leads to an oops at the first call to i2c_transfer:
$ modprobe i2c_algo_bit bit_test=1
$ modprobe cx8802
cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
cx88[0]: quirk: PCIPCI_NATOMA -- set TBFX
cx88[0]: subsystem: 0070:9202, board: Hauppauge Nova-S-Plus DVB-S [card=37,autodetected], frontend(s): 1
cx88[0]: TV tuner type 4, Radio tuner type -1
cx88[0]: SDA stuck high!
cx88[0]: i2c register FAILED
input: cx88 IR (Hauppauge Nova-S-Plus as /class/input/input5
cx88[0]/2: cx2388x 8802 Driver Manager
cx88-mpeg driver manager 0000:00:10.2: enabling device (0154 -> 0156)
cx88-mpeg driver manager 0000:00:10.2: PCI INT A -> Link[LNKD] -> GSI 9 (level, low) -> IRQ 9
cx88[0]/2: found at 0000:00:10.2, rev: 5, irq: 9, latency: 64, mmio: 0xfb000000
cx8802_probe() allocating 1 frontend(s)
cx88/2: cx2388x dvb driver version 0.0.6 loaded
cx88/2: registering cx8802 driver, type: dvb access: shared
cx88[0]/2: subsystem: 0070:9202, board: Hauppauge Nova-S-Plus DVB-S [card=37]
cx88[0]/2: cx2388x based DVB/ATSC card
BUG: unable to handle kernel NULL pointer dereference at 00000000
IP: [<e084d4ef>] :i2c_core:i2c_transfer+0x1f/0x80
*pde = 00000000
Modules linked in: cx88_dvb(+) cx8802 cx88xx ir_common i2c_algo_bit tveeprom videobuf_dvb btcx_risc
mga drm ipv6 fscpos eeprom nfsd exportfs stv0299 b2c2_flexcop_pci b2c2_flexcop cx24123 s5h1420 ves1x93
dvb_ttpci dvb_core saa7146_vv saa7146 videobuf_dma_sg videobuf_core videodev v4l1_compat ttpci_eeprom
lirc_serial lirc_dev usbhid rtc uhci_hcd 8139too i2c_piix4 i2c_core usbcore evdev
Pid: 4249, comm: modprobe Not tainted (2.6.27-gentoo #3)
EIP: 0060:[<e084d4ef>] EFLAGS: 00010296 CPU: 0
EIP is at i2c_transfer+0x1f/0x80 [i2c_core]
EAX: 00000000 EBX: ffffffa1 ECX: 00000002 EDX: d6c71e3c
ESI: d80cd050 EDI: d8093c00 EBP: d6c71e20 ESP: d6c71e0c
DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Impact: driver could possibly stomp on resources outside of its scope
{mchehab@redhat.com: I got two versions of the same patch (identical,
except for whitespacing). One authored by Andy Burns and another
authored by Suresh Siddha. Due to that, I'm applying the one that has
less CodingStyle errors. I'm also adding both comments and the SOB's for
both patches, since they are both interesting}
Suresh Siddha commented:
Alexey Fisher reported:
> resource map sanity check conflict: 0xcfeff800 0xcff007ff 0xcfe00000
> 0xcfefffff PCI Bus 0000:01
BAR base is located in the middle of the 4K page and the hardcoded
size argument makes the request span two pages causing the conflict.
Fix the hard coded size argument in ioremap().
Andy Burns commented:
I have already sent this patch on the linux-dvb list, but it didn't get
much attention, so re-sending direct, I hope you all don't mind.
While attempting to run mythtv in a xen domU, I encountered problems
loading the driver for my saa7134 card, with an error from ioremap().
This error was due to the driver allocating an incorrectly sized mmio
area, which was trapped by xen's permission checks, but this would go
un-noticed on a kernel without xen.
My card has a 1K sized mmio area, I've had information that other cards
have 2K areas, perhaps others have different sizes, yet the driver
always attempts to map 4K. I realise that the granularity of mapping is
the page size, which typically would be 4K, but unless the card's base
address happens to fall on a 4K boundary (mine does not) then the
base+4K will end up spanning two pages, and this is when the error
occurs under xen.
My patch uses the pci_resource_len macro to determine the size required
for the user's particular card, instead of the hardcoded 4K value. I've
tested with a couple of printk() inside ioremap() that the start address
and size do get rounded to the closest page boundary.
With this patch I am able to successfully load the saa7134 driver and
run mythtv under xen with my card, subject to correct pollirq settings
in case of shared IRQ, I am still seeing occasional DMA panics, which I
think are related to swiotlb handling by dom0/domU, usually the panic
occurs when changing mux, once tuned to a mux, 12 hour continuous
recordings are possible without errors.
Reported-by: Alexey Fisher <bug-track@fisher-privat.net>
Tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andy Burns <andy@burns.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove lock_kernel() call from cafe_ccic.c
Commit d56dc61265 added lock_kernel()
calls to cafe_ccic.c. But that driver was written with proper locking
and does not need the BKL, so take it back out.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the missing compat ioctls that are needed to
operate Skype in combination with libv4l and a MJPEG only camera.
If you think it's trivial enough please submit it to -stable, too.
Signed-off-by: Gregor Jasny <gjasny@web.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by David Ellingsworth:
> I'm not sure if it matters or not, but the ibmcam driver in the
> Mauro's linux-2.6 git tree in the for_linus branch is currently
> broken.
uvd is equal to NULL during most of ibmcam_probe. Due to that, an OOPS is
generated at dev_info. This patch replaces uvd->dev->dev to dev->dev
inside this routine.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reviewed-by: David Ellingsworth <david@identd.dyndns.org>
This patch add support for new device named KWorld USB FM Radio
SnapMusic Mobile 700 (FM700).
And changes few lines in comments.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update Kconfig to add missing dependency on zl10353 for dtv5100 driver.
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
rather than implementing different ways leading to confusion.
This allows multiple gate_enable/disable's in the tuner_read/write
functions, thereby lesser number of I/O operations throughout,
eventually leading to better results. As a side effect demods that
detect the STOP bit for auto closing of the gate can be avoided, thereby
a very minimal gain in disabling the auto detect feature as well.
Improves readability on the device control.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device is already handled by radio-si470x driver, and we
therefore want usbhid to ignore it.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I am trying out suspend, resume on an OMAP3 based board. What I see
during resume is that the SMC911x driver resume routing gets stuck
after trying to transmit the packet out of the controller. Some debug
messages below:
--> smc911x_drv_resume
eth0: --> smc911x_reset
eth0: smc911x_reset timeout waiting for PM restore
eth0: --> smc911x_enable
eth0: --> smc911x_phy_configure()
eth0: --> smc911x_phy_reset()
eth0: phy caps=0x782d
eth0: phy advertised caps=0x0de1
eth0: --> smc911x_phy_check_media
smc911x_phy_read: phyaddr=0x1, phyreg=0x01, phydata=0x7809
smc911x_phy_read: phyaddr=0x1, phyreg=0x01, phydata=0x7809
eth0: link down
Restarting tasks ... eth0: --> smc911x_hard_start_xmit
eth0: --> smc911x_hardware_send_pkt
eth0: --> smc911x_hard_start_xmit
eth0: --> smc911x_hardware_send_pkt
eth0: --> smc911x_hard_start_xmit
eth0: --> smc911x_hardware_send_pkt
nfs: server 172.24.190.217 not responding, still trying
nfs: server 172.24.190.217 not responding, still trying
The following change makes it work fine: (The change within
smc911x_drv_probe function was to get rid of a compilation warning).
Signed-off-by: Romit Dasgupta <romit@ti.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When the iw_cxgb3 module's cxgb3_client "add" func gets called by the
cxgb3 module, the iwarp driver ends up calling the ethtool ops get_drvinfo
function in cxgb3 to get the fw version and other info. Currently the
iwarp driver grabs the rtnl lock around this down call to serialize.
As of 2.6.27 or so, things changed such that the rtnl lock is held around
the call to the netdev driver open function. Also the cxgb3_client "add"
function doesn't get called if the device is down.
So, if you load cxgb3, then load iw_cxgb3, then ifconfig up the device,
the iw_cxgb3 add func gets called with the rtnl_lock held. If you
load cxgb3, ifconfig up the device, then load iw_cxgb3, the add func
gets called without the rtnl_lock held. The former causes the deadlock,
the latter does not.
In addition, there are iw_cxgb3 sysfs handlers that also can call
down into cxgb3 to gather the fw and hw versions. These can be called
concurrently on different processors and at any time. Thus we need to
push this serialization down in the cxgb3 driver get_drvinfo func.
The fix is to remove rtnl lock usage, and use a per-device lock in cxgb3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Protect against invalid phy entries in the eeprom.
Extend eeprom access timeout.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The doorbell writes may be seen out of order by the firmware if they
are in WC memory since the tx spin(un)lock does not flush WC writes.
Hence if the "stop" is written on a different CPU than the "go", it
is possible that the stop will arrive after the go unless we add an
explicit memory barrier (and mmiowb() is not enough).
It fixes transmit hangs in multi tx queue mode.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Addresses in the hardware status page below index 0x20 are reserved for use
by the hardware. The legacy breadcrumb was sitting at index 5. Move it to
index 0x21, and make sure everyone uses the defined value instead of
hard-coded constants.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This fixes hangs on 855-class hardware by avoiding double attachment of the
driver due to the stub second head device having the same pci id as the real
device.
Other DRM drivers probably want this treatment as well, but I'm applying it
just to this one for safety. But we should clean up the drm_pciids.h mess
now so that each driver has its own pci id list header in its own directory.
Lets do that in the next release.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
ehc->last_reset is used to ensure that resets are not issued too
close to each other. It's initialized to jiffies minus one minute
on EH entry. However, when new links are initialized after PMP is
probed, new links have zero for this timestamp resulting in long wait
depending on the current jiffies.
This patch makes last_set considered iff ATA_EHI_DID_RESET is set, in
which case last_reset is always initialized. As an added precaution,
WARN_ON() is added so that warning is printed if last_reset is
in future.
This problem is spotted and debugged by Shane Huang.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Shane Huang <Shane.Huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Phillip O'Donnell <phillip.odonnell@gmail.com> pointed out that the same
sign extension bug that was fixed in commit ba14a9c2 ("libata: Avoid
overflow in ata_tf_to_lba48() when tf->hba_lbal > 127") also appears to
exist in ata_tf_read_block(). Fix this by adding a cast to u64.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I posted this last month, but was prompted to do so again in bz#467457
Add capability flag to support slave devices with pata_sch driver.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
No arguments named @deadline in cs5535_cable_detect() and
cs5536_cable_detect(). Remove them.
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that the radeon driver has suspend/resume functions, it needs to map its
registers at load time or it will likely crash if a suspend operation occurs
before the driver has been initialized.
This patch moves the register mapping code from firstopen to load and makes
the mapping into a _DRM_DRIVER one so that the core won't remove it at
lastclose time.
Fixes (at least partially) kernel bz #11891.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
It's not used in any other drivers, and doesn't look like it will be from
drm.git master.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
When userland detected that this ioctl was supported (by version number check),
it used it in a racy way -- dispatch delayed swap, wait for vblank, continue
rendering. As there was no mechanism for it to wait for the swap to finish,
sometimes it would render before the swap and garbage would be displayed on
the screen.
By removing the ioctl and returning -EINVAL, userland returns to its previous,
correct rendering path of waiting for a vblank then dispatching a swap. The
only path that could have used this ioctl correctly was page flipping, which
relied on only one client running and emitting wait-for-vblank-before-rendering
in the command stream. That path also falls back correctly, at the performance
cost of not being able to queue up rendering before the flip occurs.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This probably just means the chipset doesn't support MSI, which is fine.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This could return early when reading after writing a buffer, if somebody
had already put it on the flushing list (write domains are 0, but still
active), leading to glReadPixels failure.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This corresponds to the setup of the sarea pointers in DMA initialization,
though neither is exactly the point at which the sarea is set up or torn down.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This register is set by the 2D driver to prevent lockups, and so it needs to
be preserved across suspend/resume too. This makes my X200s work.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Mark dca_init as a subsys_initcall since it needs to be ready to go
before dependent drivers start registering themselves.
Cc: <stable@kernel.org>
Reported-and-tested-by: Mark Rustad <mark_rustad@Xiotech.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
async_tx.callback should be checked for the first
not the last descriptor in the chain.
Cc: <stable@kernel.org>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error handling needs to be modified in dma_pin_iovec_pages().
It should return NULL instead of ERR_PTR
(pinned_list is checked for NULL in tcp_recvmsg() to determine
if iovec pages have been successfully pinned down).
In case of error for the first iovec,
local_list->nr_iovecs needs to be initialized.
Cc: <stable@kernel.org>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ioatdma driver is loaded but not used it does not allocate descriptors.
Before it frees channel resources it should first be sure
that they have been previously allocated.
Cc: <stable@kernel.org>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Tested-by: Tom Picard <tom.s.picard@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the target system cannot support SSB, then don't show the menu option as
it'll simply be an empty submenu.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts the following three commits which convert libata to
use block layer tagging.
43a49cbdf3e013e13bf62fca5ccf97
Although using block layer tagging is the right direction, due to the
tight coupling among tag number, data structure allocation and
hardware command slot allocation, libata doesn't work correctly with
the current conversion.
The biggest problem is guaranteeing that tag 0 is always used for
non-NCQ commands. Due to the way blk-tag is implemented and how SCSI
starts and finishes requests, such guarantee can't be made. I'm not
sure whether this would actually break any low level driver but it
doesn't look like a good idea to break such assumption given the
frailty of ATA controllers.
So, for the time being, keep using the old dumb in-libata qc
allocation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axobe <jens.axboe@oracle.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's showing up as regressions; disabling it very likely just papers
over an underlying issue, but time is running out for 2.6.28, lets get
back to this for 2.6.29
Fixes: #11826 and #11893
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "Exclude staging drivers" question is there so that we don't build
staging drivers for allyesconfig or allnoconfig settings, but it's very
irritating when you've already said "no" to staging drivers earlier.
There is absolutely no point in declining twice - once you've declined
the staging drivers, you're done.
So make the second question depend on the first question having been
answered in the affirmative.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use menuconfig instead of flat configs so that you can disable/enable
regulator items with one selection. Also, use depends instead of
reverse selections to make life easier, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It seems that some cards are slightly out of spec and occasionally
will not be able to complete a write in the alloted 250 ms [1].
Incease the timeout slightly to allow even these cards to function
properly.
[1] http://lkml.org/lkml/2008/9/23/390
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch fixes the setting of the Book-E watchdog timer interval setup
on initialization and by ioctl().
On initialization the period bits have to be masked before setting
a new period.
In WDIOC_SETTIMEOUT ioctl we have to use the correct mask.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'oprofile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
oprofile: Fix p6 counter overflow check
Cell OProfile: Incorrect local array size in activate spu profiling function
Revert "Cell OProfile: Incorrect local array size in activate spu profiling function"
oprofile: fix memory ordering
Cell OProfile: Incorrect local array size in activate spu profiling function
Change UTF8 chars in Kconfig help text about Oprofile AMD barcelona
Thanks to Randy Dunlap for finding this problem.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This Kconfig change allows the common 'make allmodconfig' and
'make allyesconfig' build options to skip the staging tree, which is
probably what you want to have happen anyway.
This makes the linux-next developer's life a lot easier so he doesn't
have to worry about changes that break the staging tree, that's for me
to worry about...
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
If an ACPI graphics device supports backlight brightness functions (cmp. with
latest ACPI spec Appendix B), let the ACPI video driver control backlight and
switch backlight control off in vendor specific ACPI drivers (asus_acpi,
thinkpad_acpi, eeepc, fujitsu_laptop, msi_laptop, sony_laptop, acer-wmi).
Currently it is possible to load above drivers and let both poke on the
brightness HW registers, the video and vendor specific ACPI drivers -> bad.
This patch provides the basic support to check for BIOS capabilities before
driver loading time. Driver specific modifications are in separate follow up
patches.
"acpi_backlight=vendor"
Prever vendor driver over ACPI driver for backlight.
"acpi_backlight=video" (default)
Prever ACPI driver over vendor driver for backlight.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is a reimplemention of commit
0119509c4f
from Matthew Garrett <mjg59@srcf.ucam.org>
This patch got removed because of a regression: ThinkPads with a
Intel graphics card and an Integrated Graphics Device BIOS implementation
stopped working.
In fact, they only worked because the ACPI device of the discrete, the
wrong one, got used (via int10). So ACPI functions were poking on the wrong
hardware used which is a sever bug.
The next patch provides support for above ThinkPads to be able to
switch brightness via the legacy thinkpad_acpi driver and automatically
detect when to use it.
Original commit message from Matthew Garrett:
Vendors often ship machines with a choice of integrated or discrete
graphics, and use the same DSDT for both. As a result, the ACPI video
module will locate devices that may not exist on this specific platform.
Attempt to determine whether the device exists or not, and abort the
device creation if it doesn't.
http://bugzilla.kernel.org/show_bug.cgi?id=9614
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Len's tree branch release-2.6.27, found an unwanted return statement at
evgpe.c.
(git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
release-2.6.27)
Signed-of-by Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Reformat acpi.debug_layer and acpi.debug_level documentation so it's
more readable, add some clues about how to figure out the mask bits that
enable a specific ACPI_DEBUG_PRINT statement, and include some useful
examples.
Move the list of masks to Documentation/acpi/debug.txt (these are
copies of the authoritative values in acoutput.h and acpi_drivers.h).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When CONFIG_ACPI_DEBUG=y, the default acpi_dbg_layer and acpi_dbg_level
values built into the ACPI CA have some debug output enabled. We'd
rather be quiet unless the user actually specified the acpi.debug_level
argument.
This enables distros to ship with CONFIG_ACPI_DEBUG=y without
inundating users with debug output.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
/sys/module/acpi/parameters/debug_layers used to contain only the
debug layers defined by the ACPI CA. This patch adds the additional
layer definitions for ACPI drivers.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move all the component definitions for drivers to a single shared place,
include/acpi/acpi_drivers.h.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
breakage introduced by following patch
commit 27663c5855
Author: Matthew Wilcox <willy@linux.intel.com>
Date: Fri Oct 10 02:22:59 2008 -0400
acpi_evaluate_integer() does not clear passed variable if
there is an error at evaluation.
So if we ignore error, we must supply initialized variable.
http://bugzilla.kernel.org/show_bug.cgi?id=11917
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: fix range check on mmapped sysfs resource files
PCI: remove excess kernel-doc notation
PCI: annotate return value of pci_ioremap_bar with __iomem
PCI: fix VPD limit quirk for Broadcom 5708S
This triggers false bug reports as it does a bogus kmalloc with locks held
but is never really compiled into the kernel.
Closes#8329
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As we've lost our trivial maintainer for the moment I'll send this
directly. Only touches a comment
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yup, this appears to be the problem, thanks. I think &hso_net->net->dev
is more intuitive for the error message, so I've used that. I've also
added missing line endings on the error messages and set our local
rfkill structure element to NULL on failure so we don't try to call
rfkill_unregister on driver removal if we failed to register at all.
The patch below Works For Me (TM); the device is detected fine, can be
removed without problems and connects ok. I'll have a prod at why the
rfkill stuff isn't working next, but I believe this cleanup of the error
handling is appropriate no matter what the issue with registration is.
Signed-Off-By: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Due to a hardware bug, the originally assigned range cannot reliably
be used for boot configuration and must not be modifiable through
ethtool.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tried to deactivate rx ring that wasn't activated,
used wrong index.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since commit bc45b1d39a acpi tables are
allowed to have an empty signature and /sys/firmware/acpi/tables uses the
signature as filename. Applications using naive recursion through /sys
loop forever. A possible solution would be: (replacing the zero length
filename with the string "NULL")
http://bugzilla.kernel.org/show_bug.cgi?id=11539
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Impact: cleanup
Use MACRO for rev 3 fadt id instead of 3 directly.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Could fix a bug in a hotplug add scenario.
WARNING: drivers/misc/fujitsu-laptop.o(.text+0xbde): Section mismatch in reference from the function acpi_fujitsu_add() to the variable .init.data:fujitsu_dmi_table
The function acpi_fujitsu_add() references
the variable __initdata fujitsu_dmi_table.
This is often because acpi_fujitsu_add lacks a __initdata
annotation or the annotation of fujitsu_dmi_table is wrong.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
We want to submit a patch to -next, which will remove bus_id from
"struct device", to find the remaining pieces to convert, and finally
switch over to the new api, which will remove the 20 bytes array
and does no longer have a size limitation.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Associating a Local SAPIC with a processor object is dependent upon the
processor object's definition type. CPUs declared as "Processor" should
use the Local SAPIC's 'processor_id', and CPUs declared as "Device"
should use the 'uid'. Note that for "Processor" declarations, even if a
'_UID' child object exists, it has no bearing with respect to mapping
Local SAPICs (see section 5.2.11.13 - Local SAPIC Structure; "Advanced
Configuration and Power Interface Specification", Revision 3.0b).
This patch changes the lsapic mapping logic to rely on the distinction of
how the processor object was declared - the mapping can't just try both
types of matches regardless of declaration type and rely on one failing
as is currently being done.
Signed-off-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Declaring processors in ACPI namespace can be done using either a
"Processor" definition or a "Device" definition (see section 8.4 -
Declaring Processors; "Advanced Configuration and Power Interface
Specification", Revision 3.0b). Currently the two processor
declaration types are conflated.
This patch disambiguates the processor declaration's definition type
enabling subsequent code to behave uniquely based explicitly on the
declaration's type.
Signed-off-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Fix recursive descent in __scm_destroy().
iwl3945: fix deadlock on suspend
iwl3945: do not send scan command if channel count zero
iwl3945: clear scanning bits upon failure
ath5k: correct handling of rx status fields
zd1211rw: Add 2 device IDs
Fix logic error in rfkill_check_duplicity
iwlagn: avoid sleep in softirq context
iwlwifi: clear scanning bits upon failure
Revert "ath5k: honor FIF_BCN_PRBRESP_PROMISC in STA mode"
tcp: Fix recvmsg MSG_PEEK influence of blocking behavior.
netfilter: netns ct: walk netns list under RTNL
ipv6: fix run pending DAD when interface becomes ready
net/9p: fix printk format warnings
net: fix packet socket delivery in rx irq handler
xfrm: Have af-specific init_tempsel() initialize family field of temporary selector
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] SAM9 watchdog - supported on all SAM9 and CAP9 processors
[WATCHDOG] SAM9 watchdog - update for moved headers
* 'for-linus' of git://neil.brown.name/md:
md: linear: Fix a division by zero bug for very small arrays.
md: fix bug in raid10 recovery.
md: revert the recent addition of a call to the BLKRRPART ioctl.
The architecture header files were recently moved from
include/asm-arm/mach-at91/ to arch/arm/mach-at91/include/mach/. The SAM9
watchdog driver still includes a header from the old location.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-rtc0: alarms up to one month, y3k, 114 bytes nvram, , hpet irqs irqs
+rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The atmel_serial driver is mismanaging its clock by leaving it on at all
times ... the whole point of clock management is to leave it off unless
it's actively needed, which conserves power!!
Although the kernel doesn't actually hang without my fix, it does
discard quite a lot of early console output.
The result still looks correct:
usart users= 1 on 35000000 Hz, for atmel_usart.0
usart users= 0 off 35000000 Hz, for atmel_usart.2
when using ttyS0 as serial console.
[haavard.skinnemoen@atmel.com: Make sure clock is enabled early for console]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 3e680aae4e ("fb: convert
lock/unlock_kernel() into local fb mutex") introduced several deadlocks
in the fb_compat_ioctl() path, as mutex_lock() doesn't allow recursion,
unlike lock_kernel(). This broke frame buffer applications on 64-bit
systems with a 32-bit userland.
commit 120a37470c ("framebuffer compat_ioctl
deadlock") fixed one of the deadlocks.
This patch fixes the remaining deadlocks:
- Revert commit 120a37470c,
- Extract the core logic of fb_ioctl() into a new function do_fb_ioctl(),
- Change all callsites of fb_ioctl() where info->lock is already held to
call do_fb_ioctl() instead,
- Add sparse annotations to all routines that take info->lock.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a framebuffer driver for the Fujitsu Carmine/Coral-P(A)/Lime graphics
controllers. Lime GDC support is known to work on PPC440EPx based lwmon5
and MPC8544E based socrates embedded boards, both equipped with Lime GDC.
Carmine/Coral-P PCI GDC support is known to work on PPC440EPx based
Sequoia board and also on x86 platform.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Matteo Fortini <m.fortini@selcomgroup.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This regression was introduced by commit
6ae5ce8e8d ("cciss: remove redundant code").
This patch fixes a regression where the controller firmware version is not
displayed in procfs. The previous patch would be called anytime something
changed. This will get called only once for each controller.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org> [2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Regression introduced by commit 6ae5ce8e8d
("cciss: remove redundant code").
This patch fixes a broken symlink in sysfs that was introduced by the
above commit. We broke it in 2.6.27-rc on or about 20080804. Some
installers are broken if this symlink does not exist and they may not
detect the logical drives configured on the controller. It does not
require being backported into 2.6.26.x or earlier kernels.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org> [2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for iMac 8.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Klaus Doblmann <klaus.doblmann@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add accelerometer, backlight and temperature sensor support for the new
unibody Macbook Pro 5.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add accelerometer, backlight and temperature sensor support for the new
unibody Macbook 5.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: David M. Lary <dmlary@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for iMac 5.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Ricky Campbell <johnrcampbell@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When fixing up invalid years rtc_read_alarm() was calling rtc_valid_tm()
as a boolean but rtc_valid_tm() returns zero on success or a negative
number if the time is not valid so the test was inverted.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Problem 1 (see patch below):
vc_tab_stop is declared as an array of 8 unsigned ints in struct
vc_data in include/linux/console_struct.h .
In drivers/char/vt.c only 5 of these 8 unsigned ints get initialized
leading to unintended tabulator placement on displays with more than
160 columns text.
Problem 2 (open):
Upcoming displays will have more than 256 columns of text leading to
invalid memory access in drivers/char/vt.c during tabulator
calculations:
if (vc->vc_tab_stop[vc->vc_x >> 5] & (1 << (vc->vc_x & 31)))
break;
Signed-off-by: Wolfgang Kroworsch <wolfgang@kroworsch.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As reported by Dick Gevers on Compaq ProLiant:
Oct 13 18:06:51 dvgcpl kernel: Compaq SMART2 Driver (v 2.6.0)
Oct 13 18:06:51 dvgcpl kernel: sys_init_module: 'cpqarray'->init
suspiciously returned 1, it should follow 0/-E convention
Oct 13 18:06:51 dvgcpl kernel: sys_init_module: loading module anyway...
Oct 13 18:06:51 dvgcpl kernel: Pid: 315, comm: modprobe Not tainted
2.6.27-desktop-0.rc8.2mnb #1
Oct 13 18:06:51 dvgcpl kernel: [<c0380612>] ? printk+0x18/0x1e
Oct 13 18:06:51 dvgcpl kernel: [<c0158f85>] sys_init_module+0x155/0x1c0
Oct 13 18:06:51 dvgcpl kernel: [<c0103f06>] syscall_call+0x7/0xb
Oct 13 18:06:51 dvgcpl kernel: =======================
Make it return 0 on success and -ENODEV if no array was found.
Reported-by: Dick Gevers <dvgevers@xs4all.nl>
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for 2 new SAS/SATA controllers.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes iwl3945 deadlock during suspend by moving notify_mac out
of iwl3945 mutex. This is a portion of the same fix for iwlwifi by Tomas.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ensures we clear any scan status bit when
an error occurs while sending the scan command. It is
the implementation of patch:
"iwlwifi: clear scanning bits upon failure"
for iwl3945.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_rx_status fields rs_antenna and rs_more are u8s, but we
were setting them with bitwise ANDs of 32-bit values.
As a consequence, jumbo frames would not be discarded as intended.
Then, because the hw rate value of such frames is zero, and, since
"ath5k: rates cleanup", we do not fall back to the basic rate, such
packets would trigger the following WARN_ON:
------------[ cut here ]------------
WARNING: at net/mac80211/rx.c:2192 __ieee80211_rx+0x4d/0x57e [mac80211]()
Modules linked in: ath5k af_packet sha256_generic aes_i586 aes_generic cbc loop i915 drm binfmt_misc acpi_cpufreq fan container nls_utf8 hfsplus dm_crypt dm_mod kvm_intel kvm fuse sbp2 snd_hda_intel snd_pcm_oss snd_pcm snd_mixer_oss snd_seq_dummy snd_seq_oss arc4 joydev hid_apple ecb snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device usbhid appletouch mac80211 sky2 snd ehci_hcd ohci1394 bitrev crc32 sr_mod cdrom rtc sg uhci_hcd snd_page_alloc cfg80211 ieee1394 thermal ac battery processor button evdev unix [last unloaded: ath5k]
Pid: 0, comm: swapper Tainted: G W 2.6.28-rc2-wl #14
Call Trace:
[<c0123d1e>] warn_on_slowpath+0x41/0x5b
[<c012005d>] ? sched_debug_show+0x31e/0x9c6
[<c012489f>] ? vprintk+0x369/0x389
[<c0309539>] ? _spin_unlock_irqrestore+0x54/0x58
[<c011cd8f>] ? try_to_wake_up+0x14f/0x15a
[<f81918cb>] __ieee80211_rx+0x4d/0x57e [mac80211]
[<f828872a>] ath5k_tasklet_rx+0x5a1/0x5e4 [ath5k]
[<c013b9cd>] ? clockevents_program_event+0xd4/0xe3
[<c01283a9>] tasklet_action+0x94/0xfd
[<c0127d19>] __do_softirq+0x8c/0x13e
[<c0127e04>] do_softirq+0x39/0x55
[<c0128082>] irq_exit+0x46/0x85
[<c010576c>] do_IRQ+0x9a/0xb2
[<c010461c>] common_interrupt+0x28/0x30
[<f80e934a>] ? acpi_idle_enter_bm+0x2ad/0x31b [processor]
[<c02976bf>] cpuidle_idle_call+0x65/0x9a
[<c010262c>] cpu_idle+0x76/0xa6
[<c02fb402>] rest_init+0x62/0x64
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
07fa/1196
Bewan BWIFI-USB54AR: Tested by night1308, this device is a ZD1211B with
an AL2230S radio.
0ace/b215
HP 802.11abg: Tested by Robert Philippe
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__ieee80211_tasklet_handler -> __ieee80211_rx ->
__ieee80211_rx_handle_packet -> ieee80211_invoke_rx_handlers ->
ieee80211_rx_h_decrypt -> ieee80211_crypto_tkip_decrypt ->
ieee80211_tkip_decrypt_data -> iwl4965_mac_update_tkip_key ->
iwl_scan_cancel_timeout -> msleep
Ooops!
Avoid the sleep by changing iwl_scan_cancel_timeout with
iwl_scan_cancel and simply returning on failure if the scan persists.
This will cause hardware decryption to fail and we'll handle a few more
frames with software decryption.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwl_bg_request_scan function, if we could not send a
scan command it will go to done.
In done it does the right thing to call mac80211 with
scan complete, but the problem is STATUS_SCAN_HW is still
set causing any future scan to fail. Fix by clearing the scanning status
bits if scan fails.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unfortunately, the result was that mac80211 didn't see all the beacons
it actually wanted to see. This caused lost associations.
Hopefully we can revisit this when mac80211 is less greedy about seeing
beacons directly...
This reverts commit 063279062a.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove CONFIG_ACPI_EC. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
Per section 6.5.4 of the ACPI 3.0b specification,
OSPM must make Embedded Controller operation regions, accessed
via the Embedded Controllers described in ECDT, available before
executing any control method.
The ECDT table is optional, but if it is present, the above text
means that the EC it describes is a required part of the ACPI
subsystem, so CONFIG_ACPI_EC=n wouldn't make sense.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove CONFIG_ACPI_POWER. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
The interfaces under CONFIG_ACPI_POWER (acpi_device_sleep_wake(),
acpi_power_transition(), etc) are called unconditionally from the
ACPI core, so we already depend on it always being present.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_cm_sbs_init() doesn't do anything, so we can just remove it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
I don't think there's any point in cluttering the code with these.
Better to improve the documentation so *anybody* can figure out
what layer & level to use.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The SAM9 watchdog driver is usable on the whole family of AT91SAM9 and
CAP9 processors.
Update the configuration to indicate this and allow the driver to be selected.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The architecture header files were recently moved from
include/asm-arm/mach-at91/ to arch/arm/mach-at91/include/mach/.
The SAM9 watchdog driver still includes a header from the old location.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We currently oops with a divide error on starting a linear software
raid array consisting of at least two very small (< 500K) devices.
The bug is caused by the calculation of the hash table size which
tries to compute sector_div(sz, base) with "base" being zero due to
the small size of the component devices of the array.
Fix this by requiring the hash spacing to be at least one which
implies that also "base" is non-zero.
This bug has existed since about 2.6.14.
Cc: stable@kernel.org
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Adding a spare to a raid10 doesn't cause recovery to start.
This is due to an silly type in
commit 6c2fce2ef6
and so is a bug in 2.6.27 and .28-rc.
Thanks to Thomas Backlund for bisecting to find this.
Cc: Thomas Backlund <tmb@mandriva.org>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
It turns out that it is only safe to call blkdev_ioctl when the device
is actually open (as ->bd_disk is set to NULL on last close). And it
is quite possible for do_md_stop to be called when the device is not
open. So discard the call to blkdev_ioctl(BLKRRPART) which was
added in
commit 934d9c23b4
It is just as easy to call this ioctl from userspace when needed (on
mdadm -S) so leave it out of the kernel
Signed-off-by: NeilBrown <neilb@suse.de>
Set mr->umem to NULL in mlx4_ib_alloc_fast_reg_mr(). Otherwise
ib_dereg_mr() may invoke ib_umem_release() on a random pointer value
and get an oops.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For "unlock" cycles to 16bit devices in 8bit compatibility mode we need
to use the byte addresses 0xaaa and 0x555. These effectively match
the word address 0x555 and 0x2aa, except the latter has its low bit set.
Most chips don't care about the value of the 'A-1' pin in x8 mode,
but some -- like the ST M29W320D -- do. So we need to be careful to
set it where appropriate.
cfi_send_gen_cmd is only ever passed addresses where the low byte
is 0x00, 0x55 or 0xaa. Of those, only addresses ending 0xaa are
affected by this patch, by masking in the extra low bit when the device
is known to be in compatibility mode.
[dwmw2: Do it only when (cmd_ofs & 0xff) == 0xaa]
v4: Fix stupid typo in cfi_build_cmd_addr that failed to compile
I'm writing this patch way to late at night.
v3: Bring all of the work back into cfi_build_cmd_addr
including calling of map_bankwidth(map) and cfi_interleave(cfi)
So every caller doesn't need to.
v2: Only modified the address if we our device_type is larger than our
bus width.
Cc: stable@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Compiling with CONFIG_SMP = n and CONFIG_PS3_LPM != n gives this error:
drivers/ps3/ps3-lpm.c:838: error: implicit declaration of function 'get_hard_smp_processor_id'
This fixes it. We have to include <asm/smp.h> rather than
<linux/smp.h> because the UP definition of get_hard_smp_processor_id()
is in <asm/smp.h>, and <linux/smp.h> only includes <asm/smp.h> if
CONFIG_SMP = y.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix
drivers/net/mlx4/profile.c:55: warning: 'res_name' defined but not used
by making mlx4_dbg() always use all of its parameters, regardless of
whether CONFIG_MLX4_DEBUG is set or not.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
xfrm: Fix xfrm_policy_gc_lock handling.
niu: Use pci_ioremap_bar().
bnx2x: Version Update
bnx2x: Calling netif_carrier_off at the end of the probe
bnx2x: PCI configuration bug on big-endian
bnx2x: Removing the PMF indication when unloading
mv643xx_eth: fix SMI bus access timeouts
net: kconfig cleanup
fs_enet: fix polling
XFRM: copy_to_user_kmaddress() reports local address twice
SMC91x: Fix compilation on some platforms.
udp: Fix the SNMP counter of UDP_MIB_INERRORS
udp: Fix the SNMP counter of UDP_MIB_INDATAGRAMS
drivers/net/smc911x.c: Fix lockdep warning on xmit.
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: mask off DET when restoring SControl for detach
libata: implement ATA_HORKAGE_ATAPI_MOD16_DMA and apply it
libata: Fix a potential race condition in ata_scsi_park_show()
sata_nv: fix generic, nf2/3 detection regression
sata_via: restore vt*_prepare_host error handling
sata_promise: add ATA engine reset to reset ops
libata restores SControl on detach; however, trying to restore
non-zero DET can cause undeterministic behavior including PMP device
going offline till power cycling. Mask off DET when restoring
SControl.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata always uses PIO for ATAPI commands when the number of bytes to
transfer isn't multiple of 16 but quantum DAT72 chokes on odd bytes
PIO transfers. Implement a horkage to skip the mod16 check and apply
it to the quantum device.
This is reported by John Clark in the following thread.
http://thread.gmane.org/gmane.linux.ide/34748
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: John Clark <clarkjc@runbox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Peter Moulder has pointed out that there is a slight chance that a
negative value might be passed to jiffies_to_msecs() in
ata_scsi_park_show(). This is fixed by saving the value of jiffies in a
local variable, thus also reducing code since the volatile variable
jiffies is accessed only once.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Tejun Heo <tj.kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
All three flavors of sata_nv's are different in how their hardreset
behaves.
* generic: Hardreset is not reliable. Link often doesn't come online
after hardreset.
* nf2/3: A little bit better - link comes online with longer debounce
timing. However, nf2/3 can't reliable wait for the first D2H
Register FIS, so it can't wait for device readiness or classify the
device after hardreset. Follow-up SRST required.
* ck804: Hardreset finally works.
The core layer change to prefer hardreset and follow up changes
exposed the above issues and caused various detection regressions for
all three flavors. This patch, hopefully, fixes all the known issues
and should make sata_nv error handling more reliable.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
commit b9d5b89b48 (sata_via: fix support
for 5287) accidently (?) removed vt*_prepare_host error handling - restore it
catched by gcc:
drivers/ata/sata_via.c: In function 'svia_init_one':
drivers/ata/sata_via.c:567: warning: 'host' may be used uninitialized in this function
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Promise ATA engines need to be reset when errors occur.
That's currently done for errors detected by sata_promise itself,
but it's not done for errors like timeouts detected outside of
the low-level driver.
The effect of this omission is that a timeout tends to result
in a sequence of failed COMRESETs after which libata EH gives
up and disables the port. At that point the port's ATA engine
hangs and even reloading the driver will not resume it.
To fix this, make sata_promise override ->hardreset on SATA
ports with code which calls pdc_reset_port() on the port in
question before calling libata's hardreset. PATA ports don't
use ->hardreset, so for those we override ->softreset instead.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
max_state is unsigned long.
don't set max_state a negative value
Cc : Thomas Sujith <sujith.thomas@intel.com>
Cc : Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
netif_carrier_off was called too early at the probe. In case of failure
or simply bad timing, this can cause a fatal error since linkwatch_event
might run too soon.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code read nothing but zeros on big-endian (wrong part of the
32bits). This caused poor performance on big-endian machines. Though this
issue did not cause the system to crash, the performance is significantly
better with the fix so I view it as critical bug fix.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PMF flag is set, the driver can access the HW freely. When the
driver is unloaded, it should not access the HW. The problem caused fatal
errors when "ethtool -i" was called after the calling instance was unloaded
and another instance was already loaded
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_mmap_fits() returns the wrong answer if the sysfs resource file size
is not a multiple of the page size. vm_end and vm_start are already
page-aligned, so size - start < nr, causing mmap() to return EINVAL.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix pci/rom.c kernel-doc function notation:
Warning(drivers/pci/rom.c:110): Excess function parameter or struct member 'return' description in 'pci_map_rom'
Warning(drivers/pci/rom.c:177): Excess function parameter or struct member 'return' description in 'pci_map_rom_copy'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
VPD quirks need to be called after the VPD capability is initialized.
Since VPD initialization now runs after pci_fixup_header (due to the
capabilities consolidation), VPD quirks should be done at
pci_fixup_final stage correspondingly.
Tested-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The mv643xx_eth mii bus implementation uses wait_event_timeout() to
wait for SMI completion interrupts.
If wait_event_timeout() would return zero, mv643xx_eth would conclude
that the SMI access timed out, but this is not necessarily true --
wait_event_timeout() can also return zero in the case where the SMI
completion interrupt did happen in time but where it took longer than
the requested timeout for the process performing the SMI access to be
scheduled again. This would lead to occasional SMI access timeouts
when the system would be under heavy load.
The fix is to ignore the return value of wait_event_timeout(), and
to re-check the SMI done bit after wait_event_timeout() returns to
determine whether or not the SMI access timed out.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The bool kconfig option added to ixgbe and myri10ge for DCA is ambigous,
so this patch adds a description to the kconfig option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'io-mappings-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
io mapping: clean up #ifdefs
io mapping: improve documentation
i915: use io-mapping interfaces instead of a variety of mapping kludges
resources: add io-mapping functions to dynamically map large device apertures
x86: add iomap_atomic*()/iounmap_atomic() on 32-bit using fixmaps
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
i915: Add GEM ioctl to get available aperture size.
drm/radeon: fixup further bus mastering confusion.
build fix: CONFIG_DRM_I915=y && CONFIG_ACPI=n
This reverts 51ac3beffd ('SMC91x: delete
unused local variable "lp"') and adds __maybe_unused markers to these
(potentially) unused variables.
The issue is that in some configurations SMC_IO_SHIFT evaluates
to '(lp->io_shift)', but in some others it's plain '0'.
Based upon a build failure report from Manuel Lauss.
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy load, there is an compatibility issue regarding PCIe write
credits with certain chipsets. It can be mitigated by limiting read
requests to 256 Bytes.
This workaround is always enabled for Tbird2 on Gladius. We also add
a module parameter to enable workaround for non-Gladius cards.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix CQ allocation for multicast receive queue applications. Before
this patch, the CQ was not lined up with the right NIC.
Signed-off-by: Vadim Makhervaks <vadim.makhervaks@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* Roll back allocated structures on failures.
* Use GFP_ATOMIC instead of GFP_KERNEL since we are holding a lock.
* Acquire nesadapter->pbl_lock when modifying PBL counters.
* Decrement PBL counters on deallocation.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
