According to EHCI spec, EHCI HC clears USBSTS.HCHalted whenever
USBCMD.RS=1.
However, it is a good practice to wait some time after setting USBCMD.RS
(approximately 100ms) until USBSTS.HCHalted become zero.
Without this waiting, VirtualBox's EHCI virtual HC accidentally hangs
(see BugLink).
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211095
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugene Korenevsky <ekorenevsky@astralinux.ru>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210110173609.GA17313@himera.home
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit
latency is too long") was constraining the xhci code not to allow U1/U2
sleep states if the latency to wake up from the U-states reached the
service interval of an periodic endpoint. This fix was not taking into
account that in case the quirk XHCI_INTEL_HOST is set, the wakeup time
will be calculated and configured differently.
It checks for u1_params.mel/u2_params.mel as a limit. But the code could
decide to write another MEL into the hardware. This leads to broken
cases where not enough bandwidth is available for other devices:
usb 1-2: can't set config #1, error -28
This patch is fixing that case by checking for timeout_ns after the
wakeup time was calculated depending on the quirks.
Fixes: 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit latency is too long")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201215193147.11738-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Switch to the generic C VDSO, as well as some cleanups of our VDSO
setup/handling code.
- Support for KUAP (Kernel User Access Prevention) on systems using the hashed
page table MMU, using memory protection keys.
- Better handling of PowerVM SMT8 systems where all threads of a core do not
share an L2, allowing the scheduler to make better scheduling decisions.
- Further improvements to our machine check handling.
- Show registers when unwinding interrupt frames during stack traces.
- Improvements to our pseries (PowerVM) partition migration code.
- Several series from Christophe refactoring and cleaning up various parts of
the 32-bit code.
- Other smaller features, fixes & cleanups.
Thanks to:
Alan Modra, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Ard
Biesheuvel, Athira Rajeev, Balamuruhan S, Bill Wendling, Cédric Le Goater,
Christophe Leroy, Christophe Lombard, Colin Ian King, Daniel Axtens, David
Hildenbrand, Frederic Barrat, Ganesh Goudar, Gautham R. Shenoy, Geert
Uytterhoeven, Giuseppe Sacco, Greg Kurz, Harish, Jan Kratochvil, Jordan
Niethe, Kaixu Xia, Laurent Dufour, Leonardo Bras, Madhavan Srinivasan, Mahesh
Salgaonkar, Mathieu Desnoyers, Nathan Lynch, Nicholas Piggin, Oleg Nesterov,
Oliver O'Halloran, Oscar Salvador, Po-Hsu Lin, Qian Cai, Qinglang Miao, Randy
Dunlap, Ravi Bangoria, Sachin Sant, Sandipan Das, Sebastian Andrzej Siewior ,
Segher Boessenkool, Srikar Dronamraju, Tyrel Datwyler, Uwe Kleine-König,
Vincent Stehlé, Youling Tang, Zhang Xiaoxu.
-----BEGIN PGP SIGNATURE-----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=Ga3K
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Switch to the generic C VDSO, as well as some cleanups of our VDSO
setup/handling code.
- Support for KUAP (Kernel User Access Prevention) on systems using the
hashed page table MMU, using memory protection keys.
- Better handling of PowerVM SMT8 systems where all threads of a core
do not share an L2, allowing the scheduler to make better scheduling
decisions.
- Further improvements to our machine check handling.
- Show registers when unwinding interrupt frames during stack traces.
- Improvements to our pseries (PowerVM) partition migration code.
- Several series from Christophe refactoring and cleaning up various
parts of the 32-bit code.
- Other smaller features, fixes & cleanups.
Thanks to: Alan Modra, Alexey Kardashevskiy, Andrew Donnellan, Aneesh
Kumar K.V, Ard Biesheuvel, Athira Rajeev, Balamuruhan S, Bill Wendling,
Cédric Le Goater, Christophe Leroy, Christophe Lombard, Colin Ian King,
Daniel Axtens, David Hildenbrand, Frederic Barrat, Ganesh Goudar,
Gautham R. Shenoy, Geert Uytterhoeven, Giuseppe Sacco, Greg Kurz,
Harish, Jan Kratochvil, Jordan Niethe, Kaixu Xia, Laurent Dufour,
Leonardo Bras, Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu
Desnoyers, Nathan Lynch, Nicholas Piggin, Oleg Nesterov, Oliver
O'Halloran, Oscar Salvador, Po-Hsu Lin, Qian Cai, Qinglang Miao, Randy
Dunlap, Ravi Bangoria, Sachin Sant, Sandipan Das, Sebastian Andrzej
Siewior , Segher Boessenkool, Srikar Dronamraju, Tyrel Datwyler, Uwe
Kleine-König, Vincent Stehlé, Youling Tang, and Zhang Xiaoxu.
* tag 'powerpc-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (304 commits)
powerpc/32s: Fix cleanup_cpu_mmu_context() compile bug
powerpc: Add config fragment for disabling -Werror
powerpc/configs: Add ppc64le_allnoconfig target
powerpc/powernv: Rate limit opal-elog read failure message
powerpc/pseries/memhotplug: Quieten some DLPAR operations
powerpc/ps3: use dma_mapping_error()
powerpc: force inlining of csum_partial() to avoid multiple csum_partial() with GCC10
powerpc/perf: Fix Threshold Event Counter Multiplier width for P10
powerpc/mm: Fix hugetlb_free_pmd_range() and hugetlb_free_pud_range()
KVM: PPC: Book3S HV: Fix mask size for emulated msgsndp
KVM: PPC: fix comparison to bool warning
KVM: PPC: Book3S: Assign boolean values to a bool variable
powerpc: Inline setup_kup()
powerpc/64s: Mark the kuap/kuep functions non __init
KVM: PPC: Book3S HV: XIVE: Add a comment regarding VP numbering
powerpc/xive: Improve error reporting of OPAL calls
powerpc/xive: Simplify xive_do_source_eoi()
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_EOI_FW
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_MASK_FW
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_SHIFT_BUG
...
Here is the big driver core updates for 5.11-rc1
This time there was a lot of different work happening here for some
reason:
- redo of the fwnode link logic, speeding it up greatly
- auxiliary bus added (this was a tag that will be pulled in
from other trees/maintainers this merge window as well, as
driver subsystems started to rely on it)
- platform driver core cleanups on the way to fixing some
long-time api updates in future releases
- minor fixes and tweaks.
All have been in linux-next with no (finally) reported issues. Testing
there did helped in shaking issues out a lot :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iEUQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynBJwCgjBAtVWXquZz4m/pyjn0HoTC7tdYAnAlQIj9s
vRbPjOgH9R+YRJzFs1Kx
=X6UP
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core updates for 5.11-rc1
This time there was a lot of different work happening here for some
reason:
- redo of the fwnode link logic, speeding it up greatly
- auxiliary bus added (this was a tag that will be pulled in from
other trees/maintainers this merge window as well, as driver
subsystems started to rely on it)
- platform driver core cleanups on the way to fixing some long-time
api updates in future releases
- minor fixes and tweaks.
All have been in linux-next with no (finally) reported issues. Testing
there did helped in shaking issues out a lot :)"
* tag 'driver-core-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (39 commits)
driver core: platform: don't oops in platform_shutdown() on unbound devices
ACPI: Use fwnode_init() to set up fwnode
misc: pvpanic: Replace OF headers by mod_devicetable.h
misc: pvpanic: Combine ACPI and platform drivers
usb: host: sl811: Switch to use platform_get_mem_or_io()
vfio: platform: Switch to use platform_get_mem_or_io()
driver core: platform: Introduce platform_get_mem_or_io()
dyndbg: fix use before null check
soc: fix comment for freeing soc_dev_attr
driver core: platform: use bus_type functions
driver core: platform: change logic implementing platform_driver_probe
driver core: platform: reorder functions
driver core: make driver_probe_device() static
driver core: Fix a couple of typos
driver core: Reorder devices on successful probe
driver core: Delete pointless parameter in fwnode_operations.add_links
driver core: Refactor fw_devlink feature
efi: Update implementation of add_links() to create fwnode links
of: property: Update implementation of add_links() to create fwnode links
driver core: Use device's fwnode to check if it is waiting for suppliers
...
Switch to use new platform_get_mem_or_io() instead of home grown analogue.
Note, the code has been moved upper in the function to allow farther cleanups,
such as resource sanity check.
Cc: linux-usb@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201209203642.27648-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_create_hcd will alloc memory for hcd, and we should
call usb_put_hcd to free it when adding fails to prevent
memory leak.
Fixes: b92a78e582 ("usb host: Oxford OXU210HP HCD driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201123145809.1456541-1-zhangqilong3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pm_runtime_enable will decrement the power disable depth. Imbalance
depth will resulted in enabling runtime PM of device fails later. Thus
a pairing decrement must be needed on the error handling path to keep it
balanced.
Fixes: 6c984b066d ("ARM: OMAP: USBHOST: Replace usbhs core driver APIs by Runtime pm APIs")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201123145719.1455849-1-zhangqilong3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a USB2 device wakeup is not enabled/supported the link state may
still be in U0 in xhci_bus_suspend(), where it's then manually put
to suspended U3 state.
Just as with selective suspend the device needs time to enter U3
suspend before continuing with further suspend operations
(e.g. system suspend), otherwise we may enter system suspend with link
state in U0.
[commit message rewording -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Maple Ridge is successor of Titan Ridge Thunderbolt controller. As
Titan Ridge this one also includes xHCI host controller. In order to
safe energy we should put it to low power state by default when idle.
For this reason allow host runtime PM for Maple Ridge.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-5-mathias.nyman@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI controller on Alpine Ridge LP keeps the whole Thunderbolt
controller awake if the host controller is not allowed to sleep.
This is the case even if no USB devices are connected to the host.
Add the Intel Alpine Ridge LP product-id to the list of product-ids
for which we allow runtime PM by default.
Fixes: 2815ef7fe4 ("xhci-pci: allow host runtime PM as default for Intel Alpine and Titan Ridge")
Cc: <stable@vger.kernel.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Synopsys xHC has an internal TRB cache of size TRB_CACHE_SIZE for
each endpoint. The default value for TRB_CACHE_SIZE is 16 for SS and 8
for HS. The controller loads and updates the TRB cache from the transfer
ring in system memory whenever the driver issues a start transfer or
update transfer command.
For chained TRBs, the Synopsys xHC requires that the total amount of
bytes for all TRBs loaded in the TRB cache be greater than or equal to 1
MPS. Or the chain ends within the TRB cache (with a last TRB).
If this requirement is not met, the controller will not be able to send
or receive a packet and it will hang causing a driver timeout and error.
This can be a problem if a class driver queues SG requests with many
small-buffer entries. The XHCI driver will create a chained TRB for each
entry which may trigger this issue.
This patch adds logic to the XHCI driver to detect and prevent this from
happening.
For every (TRB_CACHE_SIZE - 2), we check the total buffer size of
the SG list and if the last window of (TRB_CACHE_SIZE - 2) SG list length
and we don't make up at least 1 MPS, we create a temporary buffer to
consolidate full SG list into the buffer.
We check at (TRB_CACHE_SIZE - 2) window because it is possible that there
would be a link and/or event data TRB that take up to 2 of the cache
entries.
We discovered this issue with devices on other platforms but have not
yet come across any device that triggers this on Linux. But it could be
a real problem now or in the future. All it takes is N number of small
chained TRBs. And other instances of the Synopsys IP may have smaller
values for the TRB_CACHE_SIZE which would exacerbate the problem.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit uses the private data passed by parent device
to set the quirk for Synopsys xHC. This patch fixes the
SNPS xHC hang issue when the data is scattered across
small buffers which does not make atleast MPS size for
given TRB cache size of SNPS xHC.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-2-mathias.nyman@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were a bunch of issues with the patch converting the
OMAP1 OSK board to use descriptors for controlling the USB
host:
- The chip label was incorrect
- The GPIO offset was off-by-one
- The code should use sleeping accessors
This patch tries to fix all issues at the same time.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 15d157e874 ("usb: ohci-omap: Convert to use GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201130083033.29435-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core ignores the return value of struct device_driver::remove
because there is only little that can be done. For the shutdown callback
it's ps3_system_bus_shutdown() which ignores the return value.
To simplify the quest to make struct device_driver::remove return void,
let struct ps3_system_bus_driver::remove return void, too. All users
already unconditionally return 0, this commit makes it obvious that
returning an error code is a bad idea and ensures future users behave
accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201126165950.2554997-2-u.kleine-koenig@pengutronix.de
retval may be reassigned to 0 after max3421_of_vbus_en_pin(),
if allocate memory failed after this, max3421_probe() cann't
return ENOMEM, fix this by moving assign retval afther max3421_probe().
Fixes: 721fdc83b3 ("usb: max3421: Add devicetree support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20201117061500.3454223-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ehci-mxc driver was only used by i.MX non-DT platforms.
Since 5.10-rc1, i.MX has been converted to a DT-only platform and all
board files are gone.
Remove the ehci-mxc driver as there are no more users at all.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201113171231.2205-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 4b563a0666 ("ARM: imx: Remove imx21 support") the imx21
SoC is no longer supported.
Get rid of its USB driver too, which is now unused.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201109210813.21382-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "fallthrough" pseudo-keyword was added as a portable way to denote
intentional fallthrough. Clang will still warn on cases where there is a
fallthrough to an immediate break. Add explicit breaks for those cases.
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20201111014716.260633-1-ndesaulniers@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_get_sync() will increment pm usage at first and it
will resume the device later. We should decrease the usage count
whetever it succeeded or failed(maybe runtime of the device has
error, or device is in inaccessible state, or other error state).
If we do not call put operation to decrease the reference, it will
result in reference leak in xhci_histb_probe. Moreover, this
device cannot enter the idle state and always stay busy or other
non-idle state later. So we fixed it by jumping to error handling
branch.
Fixes: c508f41da0 ("xhci: hisilicon: support HiSilicon STB xHCI host controller")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201106122221.2304528-1-zhangqilong3@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Creating debugfs files while loding the spin_lock_irqsave(xhci->lock)
creates a lock dependecy that could possibly deadlock.
Lockdep warns:
=====================================================
WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
5.10.0-rc1pdx86+ #8 Not tainted
-----------------------------------------------------
systemd-udevd/386 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
ffffffffb1a94038 (pin_fs_lock){+.+.}-{2:2}, at: simple_pin_fs+0x22/0xa0
and this task is already holding:
ffff9e7b87fbc430 (&xhci->lock){-.-.}-{2:2}, at: xhci_alloc_streams+0x5f9/0x810
which would create a new lock dependency:
(&xhci->lock){-.-.}-{2:2} -> (pin_fs_lock){+.+.}-{2:2}
Create the files a bit later after lock is released.
Fixes: 673d746836 ("usb: xhci: add debugfs support for ep with stream")
CC: Li Jun <jun.li@nxp.com>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reported-by: Mike Galbraith <efault@gmx.de>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some platform of AMD, S3 fails with HCE and SRE errors. To fix this,
need to disable a bit which is enable in sparse controller.
Cc: stable@vger.kernel.org #v4.19+
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An incorrect sizeof() is being used, sizeof(rhub->ports) is not
correct, it should be sizeof(*rhub->ports). This bug did not
cause any issues because it just so happens the sizes are the same.
Fixes: bcaa9d5c59 ("xhci: Create new structures to store xhci port information")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
tegra_ehci_probe().
Fixes: 79ad3b5add ("usb: host: Add EHCI driver for NVIDIA Tegra SoCs")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20201026090657.49988-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fsl_usb2_device_register() should stop init if dma_set_mask() return
error.
Fixes: cae0586104 ("drivers/usb/host: fsl: Set DMA_MASK of usb platform device")
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Link: https://lore.kernel.org/r/20201010060308.33693-1-ran.wang_1@nxp.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No one is calling this function, so it's pointless to keep around as it
is triggering automated scanning tools to try to fix up the problems
with it using in_interrupt().
So delete the thing.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reported-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20201028113107.2007742-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usage of in_interrupt() in drivers is phased out for various reasons.
xhci_set_hc_event_deq() has an !in_interrupt() check which is pointless
because the function is only invoked from xhci_mem_init() which is clearly
task context as it does GFP_KERNEL allocations. Remove it.
xhci_urb_enqueue() prints a debug message if an URB is submitted after the
underlying hardware was suspended. But that warning is only issued when
in_interrupt() is true, which makes no sense. Simply return -ESHUTDOWN and
be done with it.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20201019101110.148631116@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_hcd_msp_remove() has a pdev argument which isn't used and the function
is used only within this file.
Remove pdev and make usb_hcd_msp_remove() static.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201019101110.530302737@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usage of in_interrupt() in drivers is phased out for various reasons.
Various comments use !in_interrupt() to describe calling context for probe()
and remove() functions. That's wrong because the calling context has to be
preemptible task context, which is not what !in_interrupt() describes.
Cleanup the comments. While at it add the missing kernel doc argument
descriptors.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Link: https://lore.kernel.org/r/20201019101110.439968251@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a comment explaining why find_tt() will not return error even though
find_tt() is checking for NULL and other errors.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20201011205008.24369-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To show the trb ring of streams, use the exsiting ring files of bulk ep
to show trb ring of one specific stream ID, which stream ID's trb ring
will be shown, is controlled by a new debugfs file stream_id, this is to
avoid to create a large number of dir for every allocate stream IDs,
another debugfs file stream_context_array is created to show all the
allocated stream context array entries.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure xHC completes the configure endpoint command and xhci driver
sets the ring pointers correctly before we create the user readable
debugfs file.
In theory there was a small gap where a user could have read the
debugfs file and cause a NULL pointer dereference error as ring
pointer was not yet set, in practise we want this change to simplify
the upcoming streams debugfs support.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
controllers with XHCI_AVOID_BEI quirk cause too frequent interrupts
and affect power management.
To avoid interrupting on every isochronous interval the BEI (Block
Event Interrupt) flag is set for all except the last Isoch TRB in a URB.
This lead to event ring filling up in case several isoc URB were
queued and cancelled rapidly, which some controllers didn't
handle well, and thus the XHCI_AVOID_BEI quirk was introduced.
see commit 227a4fd801 ("usb: xhci: apply XHCI_AVOID_BEI quirk to all
Intel xHCI controllers")
With the XHCI_AVOID_BEI quirk each Isoch TRB will trigger an interrupt.
This can cause up to 8000 interrupts per second for isochronous transfers
with HD USB3 cameras, affecting power saving.
The event ring fits 256 events, instead of interrupting on every
isochronous TRB if XHCI_AVOID_BEI is set we make sure at least every
8th Isochronous TRB asserts an interrupt, clearing the event ring.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the xhci-plat.c is the platform driver, after the runtime pm is
enabled, the xhci_suspend is called if nothing is connected on
the port. When the system goes to suspend, it will call xhci_suspend again
if USB wakeup is enabled.
Since the runtime suspend wakeup setting is not always the same as
system suspend wakeup setting, eg, at runtime suspend we always need
wakeup if the controller is in low power mode; but at system suspend,
we may not need wakeup. So, we move the judgement after changing
wakeup setting.
[commit message rewording -Mathias]
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this change, there will be a wakeup entry at /sys/../power/wakeup,
and the user could use this entry to choose whether enable xhci wakeup
features (wake up system from suspend) or not.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DRD controllers (eg, dwc3 & cdns3) have PHY management at
their own driver to cover both device and host mode, so add one
priv quirk for such users to skip PHY management from HCD core.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The if {} condition is duplicated with outer if {} condition.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
