The call to free_netdev() in __rtl8139_cleanup_dev() clears the network device
napi list, and explicit calls to netif_napi_del() are unnecessary.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit removed calls to rtl_set_rx_mode(). This is ok for the
standard path if the link is brought up, however it breaks system
resume from suspend. Link comes up but no network traffic.
Meanwhile common code from rtl_hw_start_8169/8101/8168() was moved
to rtl_hw_start(), therefore re-add the call to rtl_set_rx_mode()
there.
Due to adding this call we have to move definition of rtl_hw_start()
after definition of rtl_set_rx_mode().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: 82d3ff6dd1 ("r8169: remove calls to rtl_set_rx_mode")
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit a92a08499b "r8169: improve runtime pm in general and
suspend unused ports" interfaces w/o link are runtime-suspended after
10s. On systems where drivers take longer to load this can lead to the
situation that the interface is runtime-suspended already when it's
initially brought up.
This shouldn't be a problem because rtl_open() resumes MAC/PHY.
However with at least one chip version the interface doesn't properly
come up, as reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=199549
The vendor driver uses a delay to give certain chip versions some
time to resume before starting the PHY configuration. So let's do
the same. I don't know which chip versions may be affected,
therefore apply this delay always.
This patch was reported to fix the issue for RTL8168h.
I was able to reproduce the issue on an Asus H310I-Plus which also
uses a RTL8168h. Also in my case the patch fixed the issue.
Reported-by: Slava Kardakov <ojab@ojab.ru>
Tested-by: Slava Kardakov <ojab@ojab.ru>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is basically the same as 6e74d1749a ("r8152: replace
get_protocol with vlan_get_protocol"). Use vlan_get_protocol
instead of duplicating the functionality.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interpreting a member of an u16 array as u32 may result in a misaligned
access. Also it's not really intuitive to define a mac address variable
as array of three u16 words. Therefore use an array of six bytes that
is properly aligned for 32 bit access.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some chips have a non-zero function id, however instead of hardcoding
the id's (CSIAR_FUNC_NIC and CSIAR_FUNC_NIC2) we can get them
dynamically via PCI_FUNC(pci_dev->devfn). This way we can get rid
of the csi_ops.
In general csi is just a fallback mechanism for PCI config space
access in case no native access is supported. Therefore let's
try native access first.
I checked with Realtek regarding the functionality of config space
byte 0x070f and according to them it controls the L0s/L1
entrance latency.
Currently ASPM is disabled in general and therefore this value
isn't used. However we may introduce a whitelist for chips
where ASPM is known to work, therefore let's keep this code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only two places are left where rtl_generic_op() is used, so we can
inline it and simplify the code a little.
This change also avoids the overhead of unlocking/locking in case
the respective operation isn't set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some longer if statements can be simplified by using switch
statements instead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several switch statements can be significantly simplified by using
case ranges.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After merging r810x_pll_power_down/up and r8168_pll_power_down/up we
don't need member pll_power_ops any longer and can drop it, thus
simplifying the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
r810x_pll_power_down/up and r8168_pll_power_down/up have a lot in common,
so we can simplify the code by merging the former into the latter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functionality of 810x_phy_power_up/down is covered by the default
clause in 8168_phy_power_up/down. Therefore we don't need these
functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL_GIGA_MAC_VER_23/24 are configured by rtl_hw_start_8168cp_2()
and rtl_hw_start_8168cp_3() respectively which both apply
CPCMD_QUIRK_MASK, thus clearing bit ASF.
Bit ASF isn't set at any other place in the driver, therefore this
check can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use disable_irq_nosync() instead of disable_irq() as this might be
called in atomic context with netpoll.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip-specific init code includes quite some calls which are
identical for all chips. So move these calls to tp->hw_start().
In addition move rtl_set_rx_max_size() a little to make sure it's
defined before it's used. Unfortunately the diff generated by git
is a little bit hard to read.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__dev_open() calls the ndo_set_rx_mode callback anyway, so we don't
have to do it here too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently done:
- if mac_version in (01, 02, 03, 04)
RTL_W8(tp, ChipCmd, CmdTxEnb | CmdRxEnb);
- if mac_version in (01, 02, 03, 04)
rtl_set_rx_tx_config_registers(tp);
- if mac_version not in (01, 02, 03, 04)
RTL_W8(tp, ChipCmd, CmdTxEnb | CmdRxEnb);
rtl_set_rx_tx_config_registers(tp);
So we do exactly the same independent of chip version and can simplify
the code.
In addition remove the call to rtl_init_rxcfg(), it's called in
rtl_init_one() already and the set bits are never touched later.
rtl_init_8168/8101 don't include this call either.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both quirk masks are the same, so we can merge them. The quirk mask
includes most bits so it's actually easier to define a mask with
the bits to keep.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tp->cp_cmd is supposed to reflect the current value of the CplusCmd
register. Several (quite old) changes however directly change this
register w/o updating tp->cp_cmd. Also we have places in the code
reading this register where we could use the cached value.
In addition:
- Properly initialize tp->cmd with the register value.
- In rtl_hw_start_8169 remove one setting of PCIMulRW because it's
set unconditionally anyway a few lines later.
- In rtl_hw_start_8168 properly mask out the INTT bits before
setting INTT_1. So far we rely on both bits being zero.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__rtl8169_set_features is used in rtl8169_set_features only, so we
can inline it. In addition:
- Remove check (features ^ dev->features), __netdev_update_features
check's already that requested features differ from current ones.
- Don't mask out unsupported flags, there's no benefit in it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RxChkSum and RxVlan aren't touched outside __rtl8169_set_features
(except in probe), so they are always in sync with dev->features.
And the RxConfig flags are set in rtl_set_rx_mode() which is
called via dev_set_rx_mode() from __dev_open().
Therefore we can safely remove this call.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no benefit in using netif_info et al before the net_device has
been registered. We get messages like
r8169 0000:03:00.0 (unnamed net_device) (uninitialized): [message]
Therefore use dev_info/dev_err instead.
As a side effect we don't need parameter dev for function
rtl8169_get_mac_version() any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the chip configuration entries only RTL8169 (ver <= 06)
supports tx checksumming for jumbo packets.
By the way: constant JUMBO_1K is a little misleading because it refers
to the standard packet size and not to a jumbo packet size.
By implementing this rule we can get rid of configuring tx checksumming
support per chip type.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The region to be used is always the first of type IORESOURCE_MEM.
We can implement this rule directly w/o having to specify which
region is the first one per configuration entry.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
txd_version is used in rtl_init_one() only, so we can drop member
txd_version from struct rtl8169_private.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain entries in array mac_info[] are redundant, so remove them:
0x7cf, 0x2c200000 (VER 33): matched by entry 0x7c8, 0x2c000000
0x7cf, 0x28300000 (VER 26): matched by entry 0x7c8, 0x28000000
0x7cf, 0x3cb00000 (VER 24): matched by entry 0x7c8, 0x3c800000
0x7cf, 0x3c400000 (VER 22): matched by entry 0x7c8, 0x3c000000
0x7cf, 0x38500000 (VER 17): matched by entry 0x7c8, 0x38000000
0x7cf, 0x44900000 (VER 39): matched by entry 0x7c8, 0x44800000
0x7cf, 0x40b00000 (VER 30): matched by entry 0x7c8, 0x40800000
0x7cf, 0x40a00000 (VER 30): matched by entry 0x7c8, 0x40800000
0x7cf, 0x34a00000 (VER 09): matched by entry 0x7c8, 0x34800000
0x7cf, 0x24a00000 (VER 09): matched by entry 0x7c8, 0x24800000
In addition don't mask out bits 30 and 29 when printing the XID.
Most likely this is a relict from the times when the driver covered
RTL8169 chip version only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For security reasons since commit ad67b74d24 "printk: hash addresses
printed with %p" %p doesn't display the full address any longer.
We could switch to %px, but I think the pointer address doesn't
provide a real benefit, so remove printing the hashed address.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can get rid of member opts1_mask and in addition save a few cpu
cycles in the hot path of rtl_rx().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code can be a little simplified by switching the interrupt handler
argument type to struct rtl8169_private *.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The counter handling functions don't deal with the net_device, so code
can be simplified by changing the argument type to
struct rtl8169_private *.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code can be simplified by changing the argument type of hw_start
callbacks from struct net_device * to struct rtl8169_private *.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is very simple and used only once, so we can inline
the two statements.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_buf_sz is constant, so we don't have to pass it as parameter and
in general can replace it with a constant.
When working on this I noticed that also before in
rtl_set_rx_max_size() a value of 0x4000 is set, what is not in line
with the chip spec. According to the spec only bits 0..13 are used
and we set an effective value of zero therefore.
However, the driver still seems to work and due to potential side
effects I'm reluctant to make a change.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_rx_fill() is called only once and directly before the call
array tp->Rx_databuff[] is filled with zero's. Therefore we don't
need this check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function doesn't use the net_device, therefore change the
parameter to type struct rtl8169_private * to simplify the code.
In addition we don't need the calculations in the memset
statements, we can use the size of the arrays directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->dev.parent has the same value as tp_to_dev(tp)
(set by SET_NETDEV_DEV() in rtl_init_one()) and we know it can't be NULL.
This allows us to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_schedule() is called from hard irq context, so we can switch to
napi_schedule_irqoff() and avoid some overhead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use generic constant NAPI_POLL_WAIT instead of defining an own
constant for the same value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not a giant leap for mankind, but let's avoid the open-coded memcpy
and use standard helper skb_copy_to_linear_data instead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 6f0333b8fd "r8169: use 50% less ram for RX ring" member
align isn't used any longer, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Member features of struct rtl8169_private isn't used any longer since
commit 6c6aa15fde "r8169: improve interrupt handling", so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace magic number "0x5 << MAX_READ_REQUEST_SHIFT" with the
appropriate constant as defined in PCI core.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflicts in drivers/net/ethernet/mellanox/mlx5/core/en_rep.c,
we had some overlapping changes:
1) In 'net' MLX5E_PARAMS_LOG_{SQ,RQ}_SIZE -->
MLX5E_REP_PARAMS_LOG_{SQ,RQ}_SIZE
2) In 'net-next' params->log_rq_size is renamed to be
params->log_rq_mtu_frames.
3) In 'net-next' params->hard_mtu is added.
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_set_drvdata() is called only after registering the net_device,
therefore we could run into a NPE if one of the functions using
driver_data is called before it's set.
Fix this by calling pci_set_drvdata() before registering the
net_device.
This fix is a candidate for stable. As far as I can see the
bug has been there in kernel version 3.2 already, therefore
I can't provide a reference which commit is fixed by it.
The fix may need small adjustments per kernel version because
due to other changes the label which is jumped to if
register_netdev() fails has changed over time.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In several places struct device is referenced by using &tp->pci_dev->dev.
Add helper tp_to_dev() to improve code readability.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the argument type to struct rtl8169_private * is more in line
with the other functions in the driver and it allows to reduce the code size.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the type of the first argument to struct rtl8169_private * is more
in line with the other functions in the driver and it allows to reduce the
code size.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
