Implement more generic quirk registers than just limit and capability
registers. This comes with the expense of a little bit more access time so
these should be only used when really needed.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some sensors do use binning but do not have valid limits in binning
registers. Use non-binning limits in that case.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
rval was not properly initialised in smiapp_read_nvm(). Do that.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The pre_pll divisor must be such that ext_clk / pre_pll divisor does not
result in a frequency that is greater than pll_ip_clk_freq. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some sensors only allow 8-bit access, so use safe 8-bit access before the
sensor has been identified.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some sensors implement only 8-bit read functionality and fail on wider
reads. Add a quirk flag for such sensors.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pass struct sensor to register access commands. This allows taking quirks
into account in register access.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of providing a function in platform data, allow also providing the
name of the external clock and use it through the clock framework.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Report SNR in 0.1 dB scale instead of raw hardware register values.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_pac7302 module supports the webcam with usb id: 093a:2627.
It is a Genius FaceCam 300.
The module does not need any changes but listing the usb id along with a vertical flip flag.
The included patch adds this to the module source.
Signed-off-by: Jozsef Marton <jmarton@users.sourceforge.net>
Acked-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Continuous flip of bit2 reg 0x70 can cause device to become unresponsive.
Also correct reg read mistake.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trival patch to get it working with my cards stuff.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Acked-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device supports V4L2_STD_ALL, but its check for 60Hz standards
is broken, as NTSC is not the only standard that uses 60Hz.
Cc: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 driver for the Video Input Port within STA2X11 board
Signed-off-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Video user controls such as brightness, contrast, saturation, and
hue are now handled.
Signed-off-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fintek-cir, ite-cir and nuvoton-cir may try to free an I/O region
and/or IRQ handler that was never allocated after a failure in their
respective probe functions. Add and use separate labels on the
failure path so they will do the right cleanup after each possible
point of failure.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are many different Medion X10 remotes that need slightly different
keymaps. We may not yet have all the needed keymaps, in which case a
wrong keymap may be used. This happened with Medion X10 OR2x remotes
before the keymap for them was added, causing the ati_remote driver to
select the Medion Digitainer keymap instead. Unfortunately, the Medion
Digitainer keymap doesn't have the standard X10 up/down scancodes
assigned to KEY_UP and KEY_DOWN keycodes, making wrongly assigned
remotes mostly unusable.
Add the regular KEY_UP and KEY_DOWN scancodes to the Medion X10
Digitainer keymap, making any Medion remote mostly usable even when
wrongly used with that keymap (standard buttons, such as
up/down/left/right, 0-9, play/stop/pause, have the same scancode in all
the X10 remotes).
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add another Medion X10 remote keymap. This is for the Medion OR2x
remotes with the Windows MCE button.
The receiver shipped with this remote has the same USB ID as the other
Medion receivers, but the name is different and is therefore used to
detect this variant.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch were applied by mistake, as it were rejected by Don, who
requested it to be broken into per-change patches.
This reverts commit 0982db20ab.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Volokh Konstantin <volokh84@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a warning when ran "make versioncheck"
drivers/staging/media/as102/as102_fe.c: 20 linux/version.h not needed.
Signed-off-by: joseph daniel <josephdanielwalter@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card is similar to TeVii s470, but has different LNB power control.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Logitech pan/tilt reset UVC control contains two V4L2 button
controls to reset pan and tilt. As the UVC control is not marked as
auto-update, the button bits are set but never reset. A pan reset that
follows a tilt reset would thus reset both pan and tilt.
Fix this by not caching the control value of write-only controls. All
standard UVC controls are either readable or auto-update, so this will
not cause any regression and will not result in extra USB requests.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This issuses applyed only for Adlink MPG24 board with go7007
& wis2804, all whese changes was tested for continuos
load&restart mode
This is minimal changes needed for start up go7007&wis2804 to work correctly
in 3.4 branch
Changes:
- When go7007 reset device, i2c was not worked (need rewrite GPIO5)
- As wis2804 has i2c_addr=0x00/*really*/, so Need set I2C_CLIENT_TEN flag for validity
- some main nonzero initialization, rewrites with kzalloc instead kmalloc
- STATUS_SHUTDOWN was placed in incorrect place, so if firmware wasn`t loaded, we
failed v4l2_device_unregister with kernel panic (OOPS)
- some new v4l2 style features as call_all(...s_stream...) for using subdev calls
- wis-tw2804.ko module code was incompatible with 3.4 branch in initialization v4l2_subdev parts.
now i2c_get_clientdata(...) contains v4l2_subdev struct instead non standart wis_tw2804 struct
Adds:
- Additional chipset tw2804 controls with: gain,auto gain,inputs[0,1],color kill,chroma gain,gain balances,
for all 4 channels (from tw2804.pdf)
- Power control for each 4 ADC (tw2804) up when s_stream(...,1), down otherwise
Signed-off-by: Volokh Konstantin <volokh84@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Demod needs some time to wake up after power on.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changes compared to version 0.1 of driver (sent 6 May):
- Initial implementation of get_rf_strength function.
- Introduction of a warning message
Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Common defines for the FC0012 (v0.5) and FC0013 tuner drivers
Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/lg2160.c: In function ‘lg216x_read_ucblocks’:
drivers/media/dvb/frontends/lg2160.c:1336:1: warning: label ‘fail’ defined but not used [-Wunused-label]
drivers/media/dvb/frontends/lg2160.c:1325:6: warning: unused variable ‘ret’ [-Wunused-variable]
drivers/media/dvb/frontends/lg2160.c:1324:23: warning: unused variable ‘state’ [-Wunused-variable]
drivers/media/dvb/frontends/lg2160.c: In function ‘lg216x_set_ensemble’:
drivers/media/dvb/frontends/lg2160.c:420:23: warning: ‘reg’ may be used uninitialized in this function [-Wuninitialized]
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro is proposing a new API to handle statistics. This functionality will
be returned after the statistics API is ready. Just remove them for now.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the ATSC-MH frontend on the WinTV Aero-m
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch adds support for a third frontend to exist on a single
DVB adapter, in the mxl111sf driver. This patch allows that to be possible.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Select this feature setting the dvb-usb-adapter caps field with
DVB_USB_ADAP_RECEIVES_RAW_PAYLOAD
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If your driver needs to deliver the raw payload to userspace without
passing through the kernel demux, use function: dvb_dmx_swfilter_raw
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This field should not be used anymore inside the frontend drivers.
The DVB core won't rely on it.
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for controlling the LG2160 and
LG2161 ATSC-MH demodulators.
[mchehab@redhat.com: fold with the next patch that was fixing the DVB ABI]
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The MxL111SF tuner is programmed the same way for ATSC-MH
as it is programmed for ATSC.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
increment the DVB API version to 5.6 to signify support for
controlling an ATSC-MH frontend.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Document the following properties for controlling an ATSC-MH frontend:
DTV_ATSCMH_FIC_VER - Version number of the FIC signaling data
DTV_ATSCMH_PARADE_ID - Parade identification number
DTV_ATSCMH_NOG - Number of MH groups per MH subframe for a designated parade
DTV_ATSCMH_TNOG - Total number of MH groups in all parades in one subframe
DTV_ATSCMH_SGN - Start group number
DTV_ATSCMH_PRC - Parade repetition cycle
DTV_ATSCMH_RS_FRAME_MODE - RS frame mode
DTV_ATSCMH_RS_FRAME_ENSEMBLE - RS frame ensemble
DTV_ATSCMH_RS_CODE_MODE_PRI - RS code mode (primary)
DTV_ATSCMH_RS_CODE_MODE_SEC - RS code mode (secondary)
DTV_ATSCMH_SCCC_BLOCK_MODE - Series Concatenated Convolutional Code Block Mode
DTV_ATSCMH_SCCC_CODE_MODE_A - Series Concatenated Convolutional Code Rate A
DTV_ATSCMH_SCCC_CODE_MODE_B - Series Concatenated Convolutional Code Rate B
DTV_ATSCMH_SCCC_CODE_MODE_C - Series Concatenated Convolutional Code Rate C
DTV_ATSCMH_SCCC_CODE_MODE_D - Series Concatenated Convolutional Code Rate D
DTV_ATSCMH_FIC_ERR - FIC error count
DTV_ATSCMH_CRC_ERR - CRC error count
DTV_ATSCMH_RS_ERR - RS error count
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
