Check for Firmware Hang (AF_FW_RECOVERY) after mailbox command
has gained access to ensure that the mailbox command does not
wait un-necessarily during a firmware recovery and prevent
premature mailbox timeout which will lead to back to back reset's.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPdrIWAAoJEDeqqVYsXL0Mny4IAMTzXGOXCykpWhdIe2R8w0Ys
eIoTJhBKoQWnLTV8cOODtwmtZcoQLeXkZmizZiAJvX6O1tOgueg+W4AFa9grxXGI
O0d1bSb2ardzU7VZrZSY60Hd4bylMwn4Xv/0dRrQMwTJO0LEeGWsJPV2+2BuXwMB
lGCNB67oUBXgMOI1jUZQRwx/mBzQ3e/gINjnpZTNKHia7YkX/yVTFISq7htgfDN7
1wRGxymbHtVap3NbtUO96BUUndAiF5vom+4WNvaQUyPrCc6aoGWjv+J9DQXY/zgv
AYjujAluK396D6YncGFAWBzYOg9WFbq54v0PRUanjcTTAu5ILs2BxqWdhmnvl14=
=IH8T
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
Pull SCSI updates from James Bottomley:
"This is primarily another round of driver updates (lpfc, bfa, fcoe,
ipr) plus a new ufshcd driver. There shouldn't be anything
controversial in here (The final deletion of scsi proc_ops which
caused some build breakage has been held over until the next merge
window to give us more time to stabilise it).
I'm afraid, with me moving continents at exactly the wrong time,
anything submitted after the merge window opened has been held over to
the next merge window."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (63 commits)
[SCSI] ipr: Driver version 2.5.3
[SCSI] ipr: Increase alignment boundary of command blocks
[SCSI] ipr: Increase max concurrent oustanding commands
[SCSI] ipr: Remove unnecessary memory barriers
[SCSI] ipr: Remove unnecessary interrupt clearing on new adapters
[SCSI] ipr: Fix target id allocation re-use problem
[SCSI] atp870u, mpt2sas, qla4xxx use pci_dev->revision
[SCSI] fcoe: Drop the rtnl_mutex before calling fcoe_ctlr_link_up
[SCSI] bfa: Update the driver version to 3.0.23.0
[SCSI] bfa: BSG and User interface fixes.
[SCSI] bfa: Fix to avoid vport delete hang on request queue full scenario.
[SCSI] bfa: Move service parameter programming logic into firmware.
[SCSI] bfa: Revised Fabric Assigned Address(FAA) feature implementation.
[SCSI] bfa: Flash controller IOC pll init fixes.
[SCSI] bfa: Serialize the IOC hw semaphore unlock logic.
[SCSI] bfa: Modify ISR to process pending completions
[SCSI] bfa: Add fc host issue lip support
[SCSI] mpt2sas: remove extraneous sas_log_info messages
[SCSI] libfc: fcoe_transport_create fails in single-CPU environment
[SCSI] fcoe: reduce contention for fcoe_rx_list lock [v2]
...
commit 44c10138fd (PCI: Change all
drivers to use pci_device->revision) converted all drivers to use
pci_dev->revision. Convert these three drivers which got missed.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Defined error codes for ping completion status.
This patch take care of Mike Christie's commets
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPZxSnAAoJEDeqqVYsXL0M0Y4IAMX0vrTVZbg6psA5/gMcWGRP
CkFXEQ8n0PL2SCaj6BoDqamJFe5Nc7dnqxM0fGawB4S9vr3rHhiOlwO+NbV9zFYC
2skBTpeL3sjgtN/jTBdfeeAa7xTYpu/XGyei0NS1A5c2AyMVXV0uYV2s4VNZxe44
tVIn1OEzM2giZ9EB1OZslDMrg5XXm3MBIUECP0LbWUhBm/35caSFKzMXRwhh7WiK
+AVmc2AZYtdEwuknDyiH7KlsaoB3vGL9pPrAUJzIgEhy2pOo2A7W72HfA4Fj+y6a
uF9HBS5zciMp1+sGWry62AjNbWgin9BRlozBEO/lJhIfMGDV1nXEIJsOkOgkdoE=
=1TxB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates from James Bottomley:
"The update includes the usual assortment of driver updates (lpfc,
qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
amount of infrastructure work in the SAS library and transport class
as well as an iSCSI update. There's also a new SCSI based virtio
driver."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
[SCSI] qla4xxx: Update driver version to 5.02.00-k15
[SCSI] qla4xxx: trivial cleanup
[SCSI] qla4xxx: Fix sparse warning
[SCSI] qla4xxx: Add support for multiple session per host.
[SCSI] qla4xxx: Export CHAP index as sysfs attribute
[SCSI] scsi_transport: Export CHAP index as sysfs attribute
[SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
[SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
[SCSI] pm8001: fix endian issue with code optimization.
[SCSI] pm8001: Fix possible racing condition.
[SCSI] pm8001: Fix bogus interrupt state flag issue.
[SCSI] ipr: update PCI ID definitions for new adapters
[SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
[SCSI] isci: improvements in driver unloading routine
[SCSI] isci: improve phy event warnings
[SCSI] isci: debug, provide state-enum-to-string conversions
[SCSI] scsi_transport_sas: 'enable' phys on reset
[SCSI] libsas: don't recover end devices attached to disabled phys
[SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
[SCSI] libsas: set attached device type and target protocols for local phys
...
Pull trivial tree from Jiri Kosina:
"It's indeed trivial -- mostly documentation updates and a bunch of
typo fixes from Masanari.
There are also several linux/version.h include removals from Jesper."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits)
kcore: fix spelling in read_kcore() comment
constify struct pci_dev * in obvious cases
Revert "char: Fix typo in viotape.c"
init: fix wording error in mm_init comment
usb: gadget: Kconfig: fix typo for 'different'
Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c"
writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header
writeback: fix typo in the writeback_control comment
Documentation: Fix multiple typo in Documentation
tpm_tis: fix tis_lock with respect to RCU
Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c"
Doc: Update numastat.txt
qla4xxx: Add missing spaces to error messages
compiler.h: Fix typo
security: struct security_operations kerneldoc fix
Documentation: broken URL in libata.tmpl
Documentation: broken URL in filesystems.tmpl
mtd: simplify return logic in do_map_probe()
mm: fix comment typo of truncate_inode_pages_range
power: bq27x00: Fix typos in comment
...
Fix following warning:-
drivers/scsi/qla4xxx/ql4_os.c:35:5: warning: symbol 'ql4xdisablesysfsboot' was not declared. Should it be static?
drivers/scsi/qla4xxx/ql4_iocb.c:461:5: warning: symbol 'qla4xxx_send_mbox_iocb' was not declared. Should it be static?
drivers/scsi/qla4xxx/ql4_os.c:3025:6: warning: symbol 'qla4xxx_do_work' was not declared. Should it be static?
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch will allow iscsiadm to create multiple session
for the same target on per host.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For offload iSCSI like qla4xxx CHAP entries are stored in FLASH.
This patch adds support to list CHAP entries stored in FLASH and
delete specified CHAP entry from FLASH using iscsi tools.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This provides unified readq()/writeq() helper functions for 32-bit
drivers.
For some cases, readq/writeq without atomicity is harmful, and order of
io access has to be specified explicitly. So in this patch, new two
header files which contain non-atomic readq/writeq are added.
- <asm-generic/io-64-nonatomic-lo-hi.h> provides non-atomic readq/
writeq with the order of lower address -> higher address
- <asm-generic/io-64-nonatomic-hi-lo.h> provides non-atomic readq/
writeq with reversed order
This allows us to remove some readq()s that were added drivers when the
default non-atomic ones were removed in commit dbee8a0aff ("x86:
remove 32-bit versions of readq()/writeq()")
The drivers which need readq/writeq but can do with the non-atomic ones
must add the line:
#include <asm-generic/io-64-nonatomic-lo-hi.h> /* or hi-lo.h */
But this will be nop in 64-bit environments, and no other #ifdefs are
required. So I believe that this patch can solve the problem of
1. driver-specific readq/writeq
2. atomicity and order of io access
This patch is tested with building allyesconfig and allmodconfig as
ARCH=x86 and ARCH=i386 on top of tip/master.
Cc: Kashyap Desai <Kashyap.Desai@lsi.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: James Bottomley <James.Bottomley@parallels.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: James Bottomley <jbottomley@parallels.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hitoshi Mitake <h.mitake@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added ping support for network connection diagnostics.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added support to post kernel host event to application using
netlink interface.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On ROM lock acquiring timeout failure, driver spews lot of warning
messages in a for loop, remove the unwanted warning message to reduce
kernel messages clutter.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In some configurations user may not have boot targets configured.
In such cases the debug messages printed out by driver look like
some kind of failure happening. However this could be a valid
case, so modified the messages to appear as warning messages
versus failure messages.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
qla4xxx_verify_boot_idx can falsely report a DDB to be boot target
if ha->pri_ddb_idx and ha->sec_ddb_idx are not initialized correctly.
What this could cause is if there is DDB entry in FLash at index 0, then
qla4xxx_verify_boot_idx would return wrong result as ha->pri_ddb_idx is not
set correctly. Fixed the qla4xxx_get_boot_info to set the ha->pri_ddb_idx and
ha->sec_ddb_idx correctly.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix the un-necessary wait for completion of a sendtarget on an
invalid DDB entry. The state of an invalid DDB entry is 0 (unassigned)
This will also avoid the delays during system boot.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This code initially added for FW debugging, we don't need this
code now so taking it out.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added debug print with error code in case of firmware error.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In case of FW hung ISP82xx generates continuous pause frames
which causes switch to disable port.
Added fix to disable generating pause frames in case of
FW hung
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During watchdog, need to monitor temperature of ISP82XX core
and set device state to FAILED when temperature reaches
"Panic" level.
Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If ql4xdisablesysfsboot = 0 and sendtargets entry as boot index then
driver does export sendtarget entries in sysfs but iscsistart does not
do discovery. So in this case let driver do the discovery and
login to the targets.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A wrong default timeout value programmed in the adapter causes driver
to wait for that much time while waiting for target discoveries to complete.
This could add huge delays during the driver load time. To avoid this,
limit the default timeout value to 12 seconds if the default timeout value
set in adapter is less than 12 seconds and greater than 120 seconds.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make qla4xxx_build_ddb_list shorter by adding more helper functions.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPBh1uAAoJEDeqqVYsXL0MnxIIAJl0SLxgX3Vo18jhv7epNaUy
Akm8VcLTjW99IAZm1x166pGjLvdeZJC5A50DxW3jQMknKYZyyxEmTGOOMVA/LuCS
J3V18tMrsEA7i1kEGx2MauRRNAvReAZl4a/nHuRc+hpVmfyQegBv1v4V0v0gzD5I
MDZSSksqtXpJhsHt2B4g/jao7RhuJYXw7NidRGzEtksax3NMyWzaIb/75Uq6eenE
HwJwCUgZZxxfRKksj/T8ShRE6BKL9wcvrm8SVNjBYF2OpnMUNCXtfLQ4fqbHtGz2
otWvoQxVERehPZhTWHk6QnLgPwBWYyIUK7ErSFMTb9EK8b3FsEZkw6/LlS/lXnI=
=Zopk
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates for post 3.2 merge window
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (67 commits)
[SCSI] lpfc 8.3.28: Update driver version to 8.3.28
[SCSI] lpfc 8.3.28: Add Loopback support for SLI4 adapters
[SCSI] lpfc 8.3.28: Critical Miscellaneous fixes
[SCSI] Lpfc 8.3.28: FC and SCSI Discovery Fixes
[SCSI] lpfc 8.3.28: Add support for ABTS failure handling
[SCSI] lpfc 8.3.28: SLI fixes and added SLI4 support
[SCSI] lpfc 8.3.28: Miscellaneous fixes in sysfs and mgmt interfaces
[SCSI] mpt2sas: Removed redundant calling of _scsih_probe_devices() from _scsih_probe
[SCSI] mac_scsi: Remove obsolete IRQ_FLG_* users
[SCSI] qla4xxx: Update driver version to 5.02.00-k10
[SCSI] qla4xxx: check for FW alive before calling chip_reset
[SCSI] qla4xxx: Fix qla4xxx_dump_buffer to dump buffer correctly
[SCSI] qla4xxx: Fix the IDC locking mechanism
[SCSI] qla4xxx: Wait for disable_acb before doing set_acb
[SCSI] qla4xxx: Don't recover adapter if device state is FAILED
[SCSI] qla4xxx: fix call trace on rmmod with ql4xdontresethba=1
[SCSI] qla4xxx: Fix CPU lockups when ql4xdontresethba set
[SCSI] qla4xxx: Perform context resets in case of context failures.
[SCSI] iscsi class: export pid of process that created
[SCSI] mpt2sas: Remove unused duplicate diag_buffer_enable param
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
Check for firmware alive and do premature completion of
mbox commands in case of FW hung before doing chip_reset
Signed-off-by: Shyam Sunder <shyam.sunder@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
KERN_INFO in printk adding new line character that mess-up
dump print format. Remove KERN_INFO to fix dump format.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This ensures the transition of dev_state from COLD to
INITIALIZING is within lock and atomic.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In function qla4xxx_iface_set_param wait for disable_acb to
complete so that set_acb will not fail.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Multiple reset request don't get handled correctly as
the driver tries to recover adapter which is in FAILED state.
Signed-off-by: Sarang Radke <sarang.radke@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
abort all active commands from eh_host_reset in-case
of ql4xdontresethba=1
Fix following call trace:-
Nov 21 14:50:47 172.17.140.111 qla4xxx 0000:13:00.4: qla4_8xxx_disable_msix: qla4xxx (rsp_q)
Nov 21 14:50:47 172.17.140.111 qla4xxx 0000:13:00.4: PCI INT A disabled
Nov 21 14:50:47 172.17.140.111 slab error in kmem_cache_destroy(): cache `qla4xxx_srbs': Can't free all objects
Nov 21 14:50:47 172.17.140.111 Pid: 9154, comm: rmmod Tainted: G O 3.2.0-rc2+ #2
Nov 21 14:50:47 172.17.140.111 Call Trace:
Nov 21 14:50:47 172.17.140.111 [<c051231a>] ? kmem_cache_destroy+0x9a/0xb0
Nov 21 14:50:47 172.17.140.111 [<c0489c4a>] ? sys_delete_module+0x14a/0x210
Nov 21 14:50:47 172.17.140.111 [<c04fd552>] ? do_munmap+0x202/0x280
Nov 21 14:50:47 172.17.140.111 [<c04a6d4e>] ? audit_syscall_entry+0x1ae/0x1d0
Nov 21 14:50:47 172.17.140.111 [<c083019f>] ? sysenter_do_call+0x12/0x28
Nov 21 14:51:50 172.17.140.111 SLAB: cache with size 64 has lost its name
Nov 21 14:51:50 172.17.140.111 iscsi: registered transport (qla4xxx)
Nov 21 14:51:50 172.17.140.111 qla4xxx 0000:13:00.4: PCI INT A -> GSI 28 (level, low) -> IRQ 28
Signed-off-by: Sarang Radke <sarang.radke@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix issue where CPU lockup is seen when ql4xdontresethba is set and
driver is "stuck" in NEED_RESET state handler.
Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For 4032, context reset was the same as chip reset, and any firmware
issue was recovered by performing a chip reset.
For 82xx, the iSCSI firmware runs along with FCoE and the NIC
firmware contexts, and an error encountered doesnot essentially mean
that a chip reset is necessary.
Perform Chip resets only in the following cases:
1. Mailbox system error.
2. Mailbox command timeout.
3. fw_heartbeat_counter counter stops incrementing.
For all other cases, only perform a context reset.
1. Command Completion with an invalid srb.
2. Other mailbox failures.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Shyam Sunder <shyam.sunder@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
iscsi_conn_setup can fail so we must check for NULL being
returned.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the qla4xxx_get_fwddb_entry returns QLA_ERROR
the nex_idx is not updated,
for (idx = 0; idx < max_ddbs; idx = next_idx) {
ret = qla4xxx_get_fwddb_entry(ha, idx, NULL, 0, NULL,
&next_idx, &state, &conn_err,
NULL, NULL);
if (ret == QLA_ERROR)
continue;
This means there is a risk that the 'idx < max_ddbs' condition will never
met and the loop will loop forever.
Fix this by explicitly increasing the next_idx in the error condition.
Maybe a break instead of continue is more appropriate, leaving the decision
on the qlogic maintainer.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
With open-iscsi support, target entries persisted in the FLASH were not
login. Added support in the qla4xxx driver to do the login on probe
time to the target entries saved in the FLASH by user.
With this changes upgrade to the new kernel with open-iscsi support in
qla4xxx will ensure users original target entries login on driver load
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The below patch fixes some typos in various parts of the kernel, as well as fixes some comments.
Please let me know if I missed anything, and I will try to get it changed and resent.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Udev uses the connection's persistent address/port in the
/dev/disk/by-path name. qla4xxx is not exporting this value
so its iscsi disk names have been lacking the iscsi info.
In the old driver we did not have this information but
we do now and can fix this by just setting the flags to tell
libiscsi/scsi_transport_iscsi to export this info in sysfs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Userspace was sending the priority/id part of the vlan tag
and sysfs was displaying the id in the vlan file. This
renames the vlan sysfs file to vlan_id to reflect that it
was showing the id and to match the vlan_priority file.
This also adds a ISCSI_NET_PARAM_VLAN_TAG iscsi nl command
to relfect that we are sending down the vlan/priority
part of the tag.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This has the driver use helpers for a common operation and fixes
a issue where if multiple iscsi params are sent they could be
sent at offsets that cause unaligned accesses. The nla helpers
account for the padding needed to align properly for the driver.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When sendtargets response is greater then max receive data segment length,
the passthrough IOCB failed with data overrun status. Solution is to
allocate space for iSCSI header in the IOCB response buffer.
JIRA Key: UPSISCSI-147
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When iscsid restarted for an existing active session, set DDB will
fail with status already logged in. In this case, we have to send
logged in event to iscsid.
JIRA Key: OPENISCSI-21
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Devices are getting blocked during continuous link up and down.
Solution is, during relogin unblock the session, using iscsi_conn_start,
before sending connection logged in event.
JIRA Key: UPSISCSI-138
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During link down, iscsid tries to do re-login to failed session. In case of
link down-up-down, LLD was sending connection login failed event to iscsid,
which is destroying the session, instead we have to continue re-login by
sending connection err event.
JIRA Key: UPSISCSI-134
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Unable to login to session if login-logout issued consecutively for
multiple sessions. Solution is to clear idx in DDB map on the basis
of no-active connection asynchronous event (AEN).
JIRA Key: UPSISCSI-135
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Firmware reserves DDBs if there are entries in the FLASH.
So there are no free DDBs left when a iSCSI login is initiated
by user space tool like iscsiadm.
Since now login is not controlled by firmware, LLD need to free
up the DDBs after firmware init. This will ensure free DDBs are
available for iSCSI logins using iscsiadm.
JIRA Key: UPSISCSI-151
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If a boot target has a BIDI CHAP enabled, then read the user/secret from
CHAP table. Do not assume BIDI chap at peer CHAP index + 1
JIRA Key: UPSISCSI-156
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The driver failed to export primary boot target if secondary target did not
exist in the FLASH. If boot targets are not valid then driver assumed 0 and
1 as default boot targets. Since these target did not exist in flash, the
driver failed exporting all the targets.
JIRA Key: UPSISCSI-148
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
QLogic applications store the CHAP information in FLASH. During login,
authentication information is provided using an index into the CHAP region.
In order to support QLogic applications along with iscsiadm, updated the
LLD to not add duplicate CHAP entries in the CHAP region and preserve the
existing CHAP info in the CHAP region in FLASH.
This allows QLogic applications to pre-write the CHAP entries in the
CHAP region.
With iscsiadm, when the CHAP authentication information is sent to the LLD, the
LLD searches for the entry in CHAP region in FLASH, if exists then do not add.
If CHAP entry does not exist then add the CHAP entry in the CHAP region.
JIRA Key: UPSISCSI-146
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver was not setting the bidirectional CHAP bit correctly in
the DDB entry.
JIRA Key: UPSISCSI-108
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
qla4xxx now uses iscsi_boot_sysfs to export the targets used
for boot to sysfs. It needs to select that config option
to make sure that module is also built.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When CONFIG_NET is disabled, SCSI_QLA_ISCSI selects SCSI_ISCSI_ATTRS,
which uses network interfaces, so the build fails with multiple errors:
warning: (ISCSI_TCP && SCSI_CXGB3_ISCSI && SCSI_CXGB4_ISCSI && SCSI_QLA_ISCSI && INFINIBAND_ISER) selects SCSI_ISCSI_ATTRS which has unmet direct dependencies (SCSI && NET)
ERROR: "skb_trim" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
ERROR: "netlink_kernel_create" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
ERROR: "netlink_kernel_release" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
...
so make SCSI_QLA_ISCSI also depend on NET to prevent the build errors.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: iscsi-driver@qlogic.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export the name of iface session is attached to. This is needed
so tools like iscsiadm/iscsistart can match the sessions to
userspace ifaces when rebuilding iscsid's state during boot.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This command is used to read ACB params from firmware
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This command will causes the firmware to update all
configurations to pre-defined factory default settings.
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hook qla4xxx in fw boot sysfs interface so iscsi tools
can use the info to create boot sessions.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
1. Remove device database entry (ddb) state.
2. Remove device database (DDB) list building.
With open-iscsi integration the logins to the target devices are
handled by the user space. So the information of target is now
maintained in the iscsi_session object. This is handled at
libiscsi level so there is no need to maintain a list of DDBs in
the qla4xxx LLD.
3. qla4xxx: Remove add_device_dynamically.
Since autologin in FW is disabled with open-iscsi integration,
driver will never get an AEN for which driver has not requested
a DDB index. So remove the add_device_dynamically function.
4. Remove qla4xxx_tgt_dscvr
Since firmware autologin is disabled this function will not work.
Now user has the ability to do the target discovery and login to
each target individually. Firwmare will not do the login on its own.
5. Remove relogin related code
All relogin is handled by userspace now. qla4xxx just need to
notify userspace of a connection failure, this triggers the
relogin.
6. Remove add_session and alloc_session
Now qla4xxx uses iscsi_session_setup that would do the necessary
allocations for session and ddb_entry.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add scsi_transport_iscsi hooks in qla4xxx to support
iSCSI session management using iscsiadm.
This patch is based on discussion here
http://groups.google.com/group/open-iscsi/browse_thread/thread/e89fd888baf656a0#
Now users can use iscsiadm to do target discovery and do login/logout to
individual targets using the qla4xxx iSCSI class interface.
This patch leaves some dead code, but to make it easier to review
we are leaving and in the next patch we will remove that old code.
V2 - NOTE: Added code to avoid waiting for AEN during login/logout
in the driver, instead added a kernel to user event
to notify iscsid about login status. Because of this
iscsid will not get blocked.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds bsg support to qla4xxx.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support to set VLAN and show vlan settings in sysfs
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
[Patch updated to new defines]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's host attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We can replace the iface param mask with the
attr_is_visible callback.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's session attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and drivers to use the attribute container
sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Move all ipaddress related param to "struct ipaddress_config"
from "struct scsi_qla_host"
- update function - qla4xxx_update_local_ip()
- Rename IPOPT_IPv4_PROTOCOL_ENABLE to IPOPT_IPV4_PROTOCOL_ENABLE
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
[update for new ISCSI_IFACE values]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allows user space (iscsiadm) to send down network configuration
parameters for LLD to set private network configuration on the iSCSI
adapters.
Based on patches from Vikas Chaudhary.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The presense of a writeq() implementation on 32-bit x86 that splits the
64-bit write into two 32-bit writes turns out to break the mpt2sas driver
(and in general is risky for drivers as was discussed in
<http://lkml.kernel.org/r/adaab6c1h7c.fsf@cisco.com>). To fix this,
revert 2c5643b1c5 ("x86: provide readq()/writeq() on 32-bit too") and
follow-on cleanups.
This unfortunately leads to pushing non-atomic definitions of readq() and
write() to various x86-only drivers that in the meantime started using the
definitions in the x86 version of <asm/io.h>. However as discussed
exhaustively, this is actually the right thing to do, because the right
way to split a 64-bit transaction is hardware dependent and therefore
belongs in the hardware driver (eg mpt2sas needs a spinlock to make sure
no other accesses occur in between the two halves of the access).
Build tested on 32- and 64-bit x86 allmodconfig.
Link: http://lkml.kernel.org/r/x86-32-writeq-is-broken@mdm.bga.com
Acked-by: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Kashyap Desai <Kashyap.Desai@lsi.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Acked-by: James Bottomley <James.Bottomley@parallels.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since queue_work does not requeue, there is no need to check
if a work is in progress using the AF_DPC_SCHEDULED flag.
queue_work would return if work is pending without adding the
work, do_dpc would again get invoked from qla4xxx_timer if
there is still DPC flags set.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Corrected logic to don't check for F/W is alive if reset is already
in progress for ISP82XX
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Do not process interrupt unconditionally during mailbox processing which can
lead to spurious interrupt. Mailbox completion are now polled if interrupt are
disabled or wait for interrupt to come in if its enabled
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Complete the cmd if sense length is zero. For cases where sense
data spans across multiple iocb's by FW, we need to hold on to the
I/O (ha->status_srb != NULL) till we have processed them all and
copied the sense data from internal buffer to scsi_cmd sense buffer.
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
- Added MBOX_ASTS_DUPLICATE_IP AEN handling.
- Update MBOX_AEN_REG_COUNT to 8 so that driver will save status
of all mbox registers in aen_q
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
Disable Interrupt MBX completion will disable the interrupt on
successful completion. Fixed the bug where driver was waiting for
Interrupt to come in for its completion. Now driver will poll for
disable interrupt MBX completion.
Signed-off-by: Sarang Radke <sarang.radke@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move relogin to all devices code from do_dpc to new
fuction qla4xxx_relogin_all_devices()
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This provides the flexibility to modify the qdepth based on different
target devices to make the best use of system resources.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We don't need to check ddb old state we can take action
based on ddb new state.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
remove ha flag AF_HBA_GOING_AWAY and added flag AF_HA_REMOVAL
to mark the other ISP-4xxx port to indicate that the driver is
being removed, so that the other port will not re-initialize
while in the process of removing the ha due to driver unload
or hba hotplug.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver has capability to add device dynamically and present
them to OS, driver no longer need to wait for DDBs to come
online during driver initialization.
Driver still issues a relogin for DDBs that are not online,
but no longer wait for DDB to come online.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FW is not able to process mbox command if FW state is failed. This will cause
mbox command to timeout and adapter reset. We have separate function to detect
FW failed state and do adapter reset. So to avoid mbox command timeout, do not
process mbox command in case of FW state failed.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove process all aen code from qla4xxx_initialize_ddb_list()
as DPC activities should be done in DPC only.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Prior to firmware state change from ACQUIRING to READY, an
0x8029 AEN is received. Added code to check previous state
being ACQUIRING in order to update the ip address in the driver.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Since if fw load is failing, running on incomplete fw load would
be fatal.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
in mailbox command do not process interrupt unconditionally,
process interrupt only in polling mode
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
IRQF_SHARED flag should not be set when calling request_irq for MSI since
this interrupt mechanism cannot be shared like standard INTx
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
IRQF_DISABLE flag is deprecated and this flag is a NOOP in kernel.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the command has timedout then the block layer has called
blk_mark_rq_complete. If qla4xxx_cmd_wait is then called
from qla4xxx_eh_host_reset, we will always fail, because if
the driver calls scsi_done then the the block layer will fail
at blk_complete_request's blk_mark_rq_complete call instead of
calling the normal completion path including the function,
blk_queue_end_tag, which releases the tag.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
grab hardware_lock in eh_abort before accessing srb to avoid
race between command completion and get refcount on srb.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* Cleanup qla4xxx_pci_mmio_enabled():
don't want to return PCI_ERS_NEED_RESET if firmware hung.
IDC will take care of it.
* Request irq after initialize_adapter() in qla82xx_error_recovery().
* Return all active commands from qla4xxx_pci_error_detected().
* Cleanup ql4_def.h
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There is a possibility that the firmware dies while the rom
lock is held. The only way to recover from this condition is
to forcefully unlock.
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Switching from doorbell mechanism to CRB register based
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
AEN 8130 Corresponds to an event representing the insertion (detection)
of a transceiver. It also reports the type of the SFP+.
AEN 8131 corresponds to the removal of a transceiver.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The seconds_since_last_heartbeat should be checked for consecutive
heartbeat checks. Currently it could happen that it gets set to
max (2 seconds) for non-consecutive heartbeat checks.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Since interrupts are registered in start_firmware(load_risc) for 82xx,
free them if init_firmware fails.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
change data type of sense_len from uint8_t to uint16_t
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
remove "ha->retry_reset_ha_cnt" from wait_for_hba_online as its
initialize to zero at driver init time so it could always return
QLA_ERROR from wait_for_hba_online() without waiting for hba to
come online.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* cleanup function qla4xxx_recovery_timeout
- No need to wakeup dpc thread from function
qla4xxx_recovery_timeout() as we are not doing anything
in do_dpc() thread when wakeup from
qla4xxx_recovery_timeout()
* cleanup function qla4xxx_wait_for_hba_online
- Remove hard coded value from qla4xxx_wait_for_hba_online().
* cleanup function qla4xxx_start_firmware_from_flash
- display seconds
* cleanup function qla4_8xxx_load_risc
- Remove redundant code.
* cleanup function qla4xxx_get_firmware_status
- update debug statement
* cleanup function qla4_8xxx_try_start_fw
- update return status
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We use read/write[bslq] but do not include linux/io.h. This causes
build failures on PPC. Include that file.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Stable Tree <stable@kernel.org>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
gcc-4.0.2:
drivers/scsi/qla4xxx/ql4_os.c: In function 'qla4_8xxx_error_recovery':
drivers/scsi/qla4xxx/ql4_glbl.h:135: sorry, unimplemented: inlining failed in call to 'qla4_8xxx_set_drv_active': function body not available
drivers/scsi/qla4xxx/ql4_os.c:2377: sorry, unimplemented: called from here
drivers/scsi/qla4xxx/ql4_glbl.h:135: sorry, unimplemented: inlining failed in call to 'qla4_8xxx_set_drv_active': function body not available
drivers/scsi/qla4xxx/ql4_os.c:2393: sorry, unimplemented: called from here
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warning:
drivers/scsi/qla4xxx/ql4_nx.c: In function 'qla4_8xxx_get_flash_info':
drivers/scsi/qla4xxx/ql4_nx.c:1952: warning: 'mid' may be used uninitialized in this function
drivers/scsi/qla4xxx/ql4_nx.c:1952: note: 'mid' was declared here
drivers/scsi/qla4xxx/ql4_nx.c:1952: warning: 'fid' may be used uninitialized in this function
drivers/scsi/qla4xxx/ql4_nx.c:1952: note: 'fid' was declared here
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Outstanding mailbox commands, have no way to recover on f/w hung, and we
timeout on waiting for mbx response. This in turn affects the recovery process
as follows:
- We might already be in dpc while waiting for mbx to complete, so recovery for
that pci function will never get invoked. Reset Timeout (10 sec) is far less
than mbx timeout (30 sec).
- Other mbx cmds will get stuck due to serial mbx access.
Solution is to identify fw-hung scenario and handle outstanding mbx commands to
have an early-exit instead of waiting for response.
Other mbx commands waiting for access will also do an early-exit if fw-hung is
still applicable.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Also, changed boundary checking from size of total
structure to verification that we received the amount of
data needed to cache inernally. This change will provide
compatibility with mbx_sys_info structure sizes in both
older and newer firmware versions.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If BIOS is enabled then drivers init firmware fails since
BIOS has done the init once.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
wait for session to come online in eh_device_reset_handler
and eh_target_reset_handler
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Handle one H/W Interrupt at a time to prevent holding off H/W lock
for longer period of time.
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fixed the DMA allocated memory freeing which wasn't taken care
in many cases.
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Handle fw_state "auto discovery in progress" correctly
to avoid marking adapter as offline.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Once the device goes *missing*, driver blocks the session
ie iscsi_block_session() to stall the I/O. So after device
comes back *online*, driver needs to unblock the session ie
iscsi_unblock_session(), else I/Os will fail even if
ddb_state is ONLINE.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If fw ddb state is ACTIVE mark driver ddb stat as ONLINE and
unblock iscsi session.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
used cmd->host_scribble to store iocb command handle.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Per RFC 3720, Login Response Status Code 0x02 should not be retried.
Condensed connection error checking code to a single routine, and
added check for status class 0x02.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Updated firmware ready timeout algorithm to prevent
long delays and use jiffies to time out instead of
counter. Also use msleep_interruptible instead of msleep.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Link Down -> Mark all devices missing
Previously, the driver took no action on a Link Down,
and waited for the I/O on a dead connection to timeout
in the firmware before marking the DDB missing.
Link Up -> Mark all devices online
F/W will do auto login to all the devices only once.
After that its the responsibility of the driver to
relogin to devices whenever there is :
* Any sort of connection failure or
* KATO expires indicating target has logged out or
* I/O times out etc.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix operator precedence warning (from sparse), which results in the
data value always being 0:
drivers/scsi/qla4xxx/ql4_mbx.c:470:66: warning: right shift by bigger than source value
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ravi Anand <ravi.anand@qlogic.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Cc: Karen Higgins <karen.higgins@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
If the nvram is invalid qla4xxx tries to set Asuint32_t
based on the card type. If the card type is not listed
then Asuint32_t is going to be gargabe. This just fixes
that if/elseif by adding a else to catch the case for
new hardware that might not be listed yet.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The residual variable is only valid for udnerrun so do
not print it out for the overrun case.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
[Mike Christie: Fix coding style issues in patch]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Removed unnecessary hiwat code to free up the number available IOCBs.
Eliminates unnecessary eh_ escalations due to inability to obtain IOCB
pkt for marker.
v2.
- Remove define not used anymore and fix req_q_coun accounting.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
[michaelc: ported patch from qlogic.com driver to upstream]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
eh_device_reset may be called from scsi error handler or sg_reset, etc.
When called from sg_reset, there will not be an associated srb. The
driver should lookup the corresponding device handle given information
from the supplied cmd structure and should not assume that there exists
an srb.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fixed driver bug where adapter recovery did not complete if there were
outstanding commands detected on that host adapter.
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Recently dm-multipath began calling blk_abort_queue. This causes all the
commands/request running on the path to have the timeout function called.
If a path does go down, and the LLD returns DID_*, dm-multpiath will eventually
get this error and begin to call the cmd timeout handler. qla4xxx currently
does not set a timed out handler and so the default one could return
BLK_EH_NOT_HANDLED and end up firing the scsi eh and stopping IO to all
paths on the host when only one path is affected.
For software and offload iscsi we have a timed out handler already.
This patch adds a driver specific one to qla4xxx because there
are some ddb->state and session->state and command completion races
that are better handled in the LLD.
This also handles the problem where if the session is down,
we do not need the scsi eh to run until the transport code
has tried to reconnect us.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fixed sense data errors occurring above the first 32 bytes,
as required by some third party applications. Sense data
in the first 32 bytes has always been correct.
Patch updated to use srb data variables instead of scsi command
scratchpad data area, as scratchpad area is already used.
Also, corrected debug print alignment bug in dump_buffer routine.
Changed KERN_DEBUG to KERN_INFO in printk statements in this routine.
Changed version number to 5.01.00-k9
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
[michaelc: fixed checkpath.pl errors]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
qla4xxx does not check the I_T nexus values correctly
so it ends up creating one session to the target. If
a portal should disappear or they should be reported
in different order the driver will think it is already
logged in when it could now be speaking to a different
target portal or accessing it through a different
initiator port (iscsi initiator port is not tied to
hardware and is just the initiator name plus isid
so you could end up with multiple ports through one
host).
This patch has the driver check the iscsi scsi port
values when matching sessions (we do not check
the initiator name because that is static). It results
in a portal from each target portal group getting
logged into instead of just one per target. In the future
the firmware should hopefully send us notification of other
sessions that are created to other portals within the
same tpgt and the sessions should have different isids.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix misspelling of "firmware" in ql4_mbx.c
It's spelled "firmware".
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver knows when hardware is removed like with cxgb3i,
bnx2i, qla4xxx and iser then we will want to remove the sessions/devices
that are bound to that device before removing the host.
cxgb3i and in the future bnx2i will remove the host and that will
remove all the sessions on the hba. iser can call iscsi_kill_session
when it gets an event that indicates that a hca is removed.
And when qla4xxx is hooked in to the lib (it is only hooked into
the class right now) it can call iscsi remove host like the
partial offload card drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch converts the iscsi drivers to the new host byte values.
v2
Drop some conversions. Want to avoid conflicts with other patches.
v1
initial patch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When qla4xxx begins recovery and the iscsi class is firing up to handle
it, we need to retrn SCSI_MLQUEUE_TARGET_BUSY from the driver instead
of host busy, because the session recovery only affects the one target.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.
Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We want to set the queue depth to something reasonable - not
the can_queue.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This removes the session and conn data_size fields from the iscsi_transport.
Just pass in the value like with host allocation. This patch also makes
it so the LLD iscsi_conn data is allocated with the iscsi_cls_conn.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bnx2i allocates a host per netdevice but will use libiscsi,
so this unbinds the session from the host in that code.
This will also be useful for the iser parent device dma settings
fixes.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch contains the following:
1. when hba completion status is good, check for iscsi transport
errors (underflow/overflow) prior to checking the scsi status
2. New firmware requires that one marker iocb be issued for each task
management command. The patch issues marker iocb immediately
following a LUN or Target reset.
Signed-off-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds target reset functionalty.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We are seeing EXIST errors from sysfs during device addition.
We need a start scan callout so we do not start scanning sessions
found during hba setup, before the async scsi scan code is ready.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The host reset callout could be starting to reset the hba at the same
time the dpc thread is. This creates lots of problems because they both
want to do wierd things with the firmware and interrupts, etc.
This patch just has the host reset function fully shutdown the dpc
thread before resetting the hba.
This patch also moves the setting of the session online bit to fix
a potential race with the dpc thread and iscsi recovery thread.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
the check in the residual case has an incorrect test of scsi_status
(the logic is reversed, it should be scsi_status != 0 instead of
!scsi_status. Since we checked a few lines above that scsi_status was
non-zero, just eliminate this test
Signed-off-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
qla4xxx has the old school startup/probe where it finds presetup sessions
in its flash and then attempts to log into them before returning from the
probe. This however, makes it very simple to add a iscsi class scan finished
helper which the driver can use.
In future patches Dave or I will rip apart the driver to make it more
like qla2xxx, but for now this is a very simple two line patch which
fixes the problem of trying to figure out when the initial sessions
are done being scanned.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If qla4xxx is resetting up a session and the recovery timer
fires we do not want to just set it to dead, because
the dpc thread could have just set it to online and is in the
middle of resetting it up.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This has qla4xxx use the iscsi class's check ready function
in the queue command function, so all iscsi drivers return the
same error value for common problems.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Qla4xxx can just call the iscsi recovery functions directly.
There is no need for userspace to do this for qla4xxx, because
we do not use the mutex to iterate over devices anymore and iscsi_block
/unblock_session can be called from interrupt context or the dpc thread.
And having userspace do this just creates uneeded headaches for qla4xxx root
situations where the session may experience problems. For example
during the kernel shutdown the scsi layer wants to send sync caches, but at
this time userspace is not up (iscsid is not running), so we cannot
recover from the problem.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Acked-by: James Smart <james.smart@emulex.com>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: David Somayajulu <david.somayajulu@qlogic.com>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
With the sg table code, every SCSI driver is now either chain capable
or broken (or has sg_tablesize set so chaining is never activated), so
there's no need to have a check in the host template.
Also tidy up the code by moving the scatterlist size defines into the
SCSI includes and permit the last entry of the scatterlist pools not
to be a power of two.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
print_mac() used many most net drivers and format_addr() used by
net-sysfs.c are very similar and they can be intergrated.
format_addr() is also identically redefined in the qla4xxx iscsi
driver.
Export a new function sysfs_format_mac() to be used by net-sysfs,
qla4xxx and others in the future. Both print_mac() and
sysfs_format_mac() call _format_mac_addr() to do the formatting.
Changed print_mac() to use unsigned char * to be consistent with
net_device struct's dev_addr. Added buffer length overrun checking
as suggested by Joe Perches.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces sizeof sense_buffer with SCSI_SENSE_BUFFERSIZE in
several LLDs. It's a preparation for the future changes to remove
sense_buffer array in scsi_cmnd structure.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We were using the device delete sysfs file to remove each device
then logout. Now in 2.6.21 this will not work because
the sysfs delete file returns immediately and does not wait for
the device removal to complete. This causes a hang if a cache sync
is needed during shutdown. Before .21, that approach had other
problems, so this patch fixes the shutdown code so that we remove the target
and unbind the session before logging out and shut down the session
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Prior to use struct marker in the linux kernel markers, we need to clean
two drivers which use this structure name.
Change bonding driver types :
- struct marker to struct bond_marker.
- marker_t to bond_marker_t.
- marker_header to bond_marker_header.
- marker_header_t to bond_marker_header_t.
Change qla4xxx struct marker_entry usage :
- Change struct marker_entry for struct qla4_marker_entry.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Chad Tindel <ctindel@users.sourceforge.net>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This option is true if a low-level driver can support sg
chaining. This will be removed eventually when all the drivers are
converted to support sg chaining. q->max_phys_segments is set to
SCSI_MAX_SG_SEGMENTS if false.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
On Wed, 2007-06-06 at 11:55 -0700, David C Somayajulu wrote:
This patch fixes the code handling underrun and overrun conditions.
Also fixed coding style as per Mike Christie's advice.
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch provides the following:
1. remove warning ignoring the return value of pci_set_mwi()
2. allows HBA to be online when the initiator ip address is uninitialized.
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
iSCSI must support software iscsi (iscsi_tcp, iser), hardware iscsi (qla4xxx),
and partial offload (broadcom). To be able to allow each stack or driver
or port (virtual or physical) to be able to log into the same target portal
we use the initiator tuple [[HWADDRESS | NETDEVNAME], INITIATOR_NAME] and
the target tuple [TARGETNAME, CONN_ADDRESS, CONN_PORT] to id a session.
This patch adds the netdev name, which is used by software iscsi when
it binds a session to a netdevice using the SO_BINDTODEVICE sock opt.
It cannot use HWADDRESS because if someone did vlans then the same netdevice
will have the same mac and the initiator,target id will not be unique.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch exports the local address for the session. For
qla4xxx this is the ip of the hba's port. For software
this is the src addr of the socket.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Userspace will want to know what the driver/FW/HW capabilites
when it comes to some operations like if the hardware can
do discovery or if it can store iscsi info like what target
was used for boot. This patch adds some new caps so userspace
can tell if the driver supports hardware/fw based sendtargets
discovery and if the hardware has some flash which may be
holding or can contain some iscsi target info
.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For iscsi root boot, software iscsi needs to know what the BIOS/OF
initiator used for the initiator name so this puts it in sysfs
for userspace to be able to pick up.
For hw iscsi, it is nice to see what the card is using.
This patch adds the new param, and hooks in qla4xxx, iscsi_tcp, and ib_iser.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We are going to be adding more host level sysfs attrs and
set_params, so this patch has them take a scsi_host instead
of either a scsi_host or host no.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Export mac as hw address.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Jens Axboe <jens.axboe@oracle.com> did the for_each_sg cleanup.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Free memory resources after invoking free_irq() in
qla4xxx_free_adapter(). QLA4xxx has two pci functions per port
(Ethernet and iSCSI). When one of these PCI functions issues a HBA
reset, all other functions are notified and need to acknowledge and
re-initialize. During module qla4xxx_remove_adapter() gets
invoked. This function needs to wait if it is currently responding to
a reset from another function.
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
All all inbound mbx registers for all mbx commands. Remove dead code.
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support to log all AENs and service mbx cmd completions for QLA4032
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Clean up and update version number
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In qla4xxx_get_ddb_entry() and qla4xxx_add_device_dynamically()
differentiate between a target which has been newly added vs a target
which went offline temporarily and is online again. In
qla4xxx_build_ddb_list() firmware ddb state needs to be updated by
calling qla4xxx_get_ddb_entry(). Fix qla4x00_pci_config() and clean up
code.
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for QLA4032 which supports IPv6
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for logging all AENs and clean up
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove dead code
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- make needlessly global code static
- #if 0 unused functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The included patch fixes the following issues:
1. qla3xxx/qla4xxx co-existence issue which can result in a lockup
when qla3xxx driver is unloaded, or when ifdown; ifup is performed on
one of the interfaces correponding to qla3xxx. This is because qla4xxx
HBA supports one ethernet and iscsi interfaces per port. Both iscsi
and ethernet interfaces share the same state machine. The problem has
to do with synchronizing access to the state machine in the event of a
reset
2. mutex_lock() is sometimes not followed by mutex_unlock() prior to
invoking a msleep() in qla4xxx_mailbox_command()
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
