MIPS R2 FPU instructions are also present in MIPS R6 so amend the
preprocessor definitions to take MIPS R6 into consideration.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
MIPS R6 removed quite a few R2 instructions. However, there
is plenty of <R6 userland code so we add an in-kernel emulator
so we can still be able to execute all R2 userland out there.
The emulator comes with a handy debugfs under /mips/ directory
(r2-emul-stats) to provide some basic statistics of the
instructions that are being emulated.
Below are some statistics from booting a minimal buildroot image:
Instruction Total BDslot
------------------------------
movs 236969 0
hilo 56686 0
muls 55279 0
divs 10941 0
dsps 0 0
bops 1 0
traps 0 0
fpus 0 0
loads 214981 17
stores 103364 0
llsc 56898 0
dsemul 150418 0
jr 370158
bltzl 43
bgezl 1594
bltzll 0
bgezll 0
bltzal 39
bgezal 39
beql 14503
bnel 138741
blezl 0
bgtzl 3988
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
MIPS R6 added the following four instructions which share the
BGTZ and BGTZL opcode:
BLTZALC: Compact branch-and-link if GPR rt is < to zero
BGTZALC: Compact branch-and-link if GPR rt is > to zero
BLTZL : Compact branch if GPR rt is < to zero
BGTZL : Compact branch if GPR rt is > to zero
BLTC : Compact branch if GPR rs is less than GPR rt
BLTUC : Similar to BLTC but unsigned
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
MIPS R6 added the following four instructions which share the
BLEZ and BLEZL opcodes:
BLEZALC: Compact branch-and-link if GPR rt is <= to zero
BGEZALC: Compact branch-and-link if GPR rt is >= to zero
BLEZC : Compact branch if GPR rt is <= to zero
BGEZC : Compact branch if GPR rt is >= to zero
BGEC : Compact branch if GPR rs is less than or equal to GPR rt
BGEUC : Similar to BGEC but unsigned.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
MIPS R6 introduced the following two branch instructions for COP1:
BC1EQZ: Branch if Cop1 (FPR) Register Bit 0 is Equal to Zero
BC1NEZ: Branch if Cop1 (FPR) Register Bit 0 is Not Equal to Zero
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
MIPS R6 removed the BLTZL, BGEZL, BLTZAL, BGEZAL, BEQL, BNEL, BLEZL,
BGTZL branch likely instructions so we must not try to emulate them on
MIPS R6 if the R2-to-R6 emulator is not present.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The MIPS R6 JR instruction is an alias to the JALR one, so it may
need emulation for non-R6 userlands.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Hybrid FPRs is a scheme where scalar FP registers are 64b wide, but
accesses to odd indexed single registers use bits 63:32 of the
preceeding even indexed 64b register. In this mode all FP code
except that built for the plain FP64 ABI can execute correctly. Most
notably a combination of FP64A & FP32 code can execute correctly,
allowing for existing FP32 binaries to be linked with new FP64A binaries
that can make use of 64 bit FP & MSA.
Hybrid FPRs are implemented by setting both the FR & FRE bits, trapping
& emulating single precision FP instructions (via Reserved Instruction
exceptions) whilst allowing others to execute natively. It therefore has
a penalty in terms of execution speed, and should only be used when no
fully native mode can be. As more binaries are recompiled to use either
the FPXX or FP64(A) ABIs, the need for hybrid FPRs should diminish.
However in the short to mid term it allows for a gradual transition
towards that world, rather than a complete ABI break which is not
feasible for some users & not desirable for many.
A task will be executed using the hybrid FPR scheme when its
TIF_HYBRID_FPREGS flag is set & TIF_32BIT_FPREGS is clear. A further
patch will set the flags as necessary, this patch simply adds the
infrastructure necessary for the hybrid FPR mode to work.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7683/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Starting with version 2.24.51.20140728 MIPS binutils complain loudly
about mixing soft-float and hard-float object files, leading to this
build failure since GCC is invoked with "-msoft-float" on MIPS:
{standard input}: Warning: .gnu_attribute 4,3 requires `softfloat'
LD arch/mips/alchemy/common/built-in.o
mipsel-softfloat-linux-gnu-ld: Warning: arch/mips/alchemy/common/built-in.o
uses -msoft-float (set by arch/mips/alchemy/common/prom.o),
arch/mips/alchemy/common/sleeper.o uses -mhard-float
To fix this, we detect if GAS is new enough to support "-msoft-float" command
option, and if it does, we can let GCC pass it to GAS; but then we also need
to sprinkle the files which make use of floating point registers with the
necessary ".set hardfloat" directives.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: Markos Chandras <Markos.Chandras@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8355/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 08a07904e1 ("MIPS: math-emu: Remove most ifdefery") removed
the #ifdef ISA conditions and switched to runtime detection. However,
according to the instruction set manual, the cop1x_op instructions are
available in >=MIPS32r2 as well. This fixes a problem on MIPS32r2
with the ntpd package which failed to execute with a SIGILL exit code due
to the fact that a madd.d instruction was not being emulated.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: 08a07904e1 ("MIPS: math-emu: Remove most ifdefery")
Cc: <stable@vger.kernel.org> # v3.16+
Cc: linux-mips@linux-mips.org
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/8173/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit bbd426f542 "MIPS: Simplify FP context access" modified the
SIFROMREG & SIFROMHREG macros such that they return unsigned rather
than signed 32b integers. I had believed that to be fine, but
inadvertently missed the MFC1 & MFHC1 cases which write to a struct
pt_regs regs element. On MIPS32 this is fine, but on 64 bit those
saved regs' fields are 64 bit wide. Using unsigned values caused the
32 bit value from the FP register to be zero rather than sign extended
as the architecture specifies, causing incorrect emulation of the
MFC1 & MFHc1 instructions. Fix by reintroducing the casts to signed
integers, and therefore the sign extension.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: stable@vger.kernel.org # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7848/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some versions of the assembler will not assemble CFC1 for OCTEON, so
override the ISA for these.
Add r4k_fpu.o to handle low level FPU initialization.
Modify octeon_switch.S to save the FPU registers. And include
r4k_switch.S to pick up more FPU support.
Get rid of "#define cpu_has_fpu 0"
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7006/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Sometimes it's useful to let the user, while doing performance research,
know what in the IEEE754 exceptions has caused many times of FP emulation
when running a specific application. This patch adds 5 more files to
/sys/kernel/debug/mips/fpuemustats/, whose filenames begin with "ieee754".
These stats are in addition to the existing cp1ops, cp1xops, errors, loads
and stores, which may not be useful in understanding the reasons of ieee754
exceptions.
[ralf@linux-mips.org: Fixed reject due to other changes to the kernel
FP assist software.]
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven.Hill@imgtec.com
Cc: james.hogan@imgtec.com
Patchwork: http://patchwork.linux-mips.org/patch/7044/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move microMIPS32_to_MIPS32() to a separate file which only gets built
for mipsMIPS configurations; for other configurations the optimizer
eleminates calls to microMIPS32_to_MIPS32().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Previously math-emu was using the IEEE-754 constants internally. These
were differing by having the constants for rounding to +/- infinity
switched, so a conversion was necessary. This would be entirely
avoidable if the MIPS constants were used throughout, so get rid of
the bloat.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
mm_isBranchInstr() did reside in the math emu code even though it logically
is separate and also is used outside the math emu code. In addition GCC 4.9.0
leaves the following unnnecessarily bloated function body for a non-microMIPS
configuration:
<mm_isBranchInstr>:
105c: afa50004 sw a1,4(sp)
1060: afa60008 sw a2,8(sp)
1064: afa7000c sw a3,12(sp)
1068: 03e00008 jr ra
106c: 00001021 move v0,zero
which stores arguments that are never going to be used on the stack frame.
Move mm_isBranchInstr() from cp1emu.c to branch.c, then split mm_isBranchInstr()
into a __mm_isBranchInstr() core and a mm_isBranchInstr() wrapper inline function
which only invokes __mm_isBranchInstr() on microMIPS configurations.
This shaves off 112 bytes off the kernel and improves code flow a bit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Only define variables in the outermost block
o One empty line at most
o Format comments as per CodingStyle
o Update FSF address in licensing term comment
o Spell FPU and MIPS in all capitals.
o Remove ####-type of lines in comments.
o Try to make things a bit most consistent between sp_*.c / dp_*.c files.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most of these tests should be runtime tests. This also finally means
that on a MIPS III systems MIPS IV opcodes are going to result in an
exception as they're supposed to.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The upper bits of an FP register are architecturally defined as
unpredictable following an instructions which only writes the lower
bits. The prior behaviour of the kernel is to leave them unmodified.
This patch modifies that to clear the upper bits to zero. This is what
the MSA architecture reference manual specifies should happen for its
wider registers and is still permissible for scalar FP instructions
given the bits unpredictability there.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: sergei.shtylyov@cogentembedded.com
Patchwork: https://patchwork.linux-mips.org/patch/6435/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch replaces the fpureg_t typedef with a "union fpureg" enabling
easier access to 32 & 64 bit values. This allows the access macros used
in cp1emu.c to be simplified somewhat. It will also make it easier to
expand the width of the FP registers as will be done in a future
patch in order to support the 128 bit registers introduced with MSA.
No behavioural change is intended by this patch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6532/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When running applications which contain the instruction "prefx" on FPU-less
CPUs, a message "Illegal instruction" will be seen. This instruction is
supposed to be ignored by the FPU emulator. However, its current detection
and function field encoding are incorrect. This patch fix the issue.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Steven.Hill@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/6608/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CPUs implementing MIPS32 R2 may include a 64-bit FPU, just as MIPS64 CPUs
do. In order to preserve backwards compatibility a 64-bit FPU will act
like a 32-bit FPU (by accessing doubles from the least significant 32
bits of an even-odd pair of FP registers) when the Status.FR bit is
zero, again just like a mips64 CPU. The standard O32 ABI is defined
expecting a 32-bit FPU, however recent toolchains support use of a
64-bit FPU from an O32 MIPS32 executable. When an ELF executable is
built to use a 64-bit FPU a new flag (EF_MIPS_FP64) is set in the ELF
header.
With this patch the kernel will check the EF_MIPS_FP64 flag when
executing an O32 binary, and set Status.FR accordingly. The addition
of O32 64-bit FP support lessens the opportunity for optimisation in
the FPU emulator, so a CONFIG_MIPS_O32_FP64_SUPPORT Kconfig option is
introduced to allow this support to be disabled for those that don't
require it.
Inspired by an earlier patch by Leonid Yegoshin, but implemented more
cleanly & correctly.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/6154/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for microMIPS encodings of the mfhc1 & mthc1
instructions introduced in release 2 of the mips32 & mips64
architectures, converting them to their mips32 equivalents for the FPU
emulator.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6110/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the mfhc1 & mthc1 instructions to the FPU
emulator. These instructions were introduced in release 2 of the MIPS32
& MIPS64 architectures and allow access to the most significant 32 bits
of a 64-bit FP register.
[ralf@linux-mips.org: Fix ifdef hell added by original patch.]
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6112/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There were many cases of:
return something;
break;
All those break statements are unreachable and thus redundant.
Signed-off-by: David Daney <david.daney@cavium.com>
Reviewed-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The branch emulation needs to handle the OCTEON BBIT instructions,
otherwise we get SIGILL instead of emulation.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5726/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In mm_isBranchInstr() we can short circuit the entire function if
!cpu_has_mmips.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5326/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add logic needed to do floating point emulation in microMIPS mode.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Steven J. Hill <Steven. Hill@imgtec.com>
Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The default implementation of 'cpu_has_fpu' macro calls
smp_processor_id() which causes this warning to be printed when
preemption is enabled:
[ 4.664000] Algorithmics/MIPS FPU Emulator v1.5
[ 4.676000] BUG: using smp_processor_id() in preemptible [00000000] code: ini
[ 4.700000] caller is fpu_emulator_cop1Handler+0x434/0x27b8
This problem got introduced in November 2009 by
af1d2af877ef6c36990671bc86a5b9c5bb50b1da (lmo) [MIPS: Fix emulation of
64-bit FPU on 64-bit CPUs.] rsp. da0bac3341
(kernel.org) [MIPS: Fix emulation of 64-bit FPU on FPU-less 64-bit CPUs.]
in 2.6.32.
Fixed by rewriting cop1_64bit() to return a constant whenever possible
but most importantly avoid the use pf cpu_has_fpu entirely.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Jayachandran C <jchandra@broadcom.com>
Initial-patch-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: https://patchwork.linux-mips.org/patch/4225/
This patch refactors MIPS branch emulation code so as to allow skipping
delay slot instruction in case of branch likely instructions when branch is
not taken. This is useful for keeping the code common for use cases like
kprobes where one would like to handle the branch instructions keeping the
delay slot instuction also in picture for branch likely instructions. Also
allow emulation when instruction to be decoded is not at pt_regs->cp0_epc
as in case of kprobes where pt_regs->cp0_epc points to the breakpoint
instruction.
The patch also exports the function for modules.
Signed-off-by: Maneesh Soni <manesoni@cisco.com>
Signed-off-by: Victor Kamensky <kamensky@cisco.com>
Cc: David Daney <david.daney@cavium.com>
Cc: ananth@in.ibm.com
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2913/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The nmi parameter indicated if we could do wakeups from the current
context, if not, we would set some state and self-IPI and let the
resulting interrupt do the wakeup.
For the various event classes:
- hardware: nmi=0; PMI is in fact an NMI or we run irq_work_run from
the PMI-tail (ARM etc.)
- tracepoint: nmi=0; since tracepoint could be from NMI context.
- software: nmi=[0,1]; some, like the schedule thing cannot
perform wakeups, and hence need 0.
As one can see, there is very little nmi=1 usage, and the down-side of
not using it is that on some platforms some software events can have a
jiffy delay in wakeup (when arch_irq_work_raise isn't implemented).
The up-side however is that we can remove the nmi parameter and save a
bunch of conditionals in fast paths.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Michael Cree <mcree@orcon.net.nz>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Don Zickus <dzickus@redhat.com>
Link: http://lkml.kernel.org/n/tip-agjev8eu666tvknpb3iaj0fg@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We were unconditionally sending SIGBUS with an empty siginfo on FP
emulator faults. This differs from what happens when real floating
point hardware would get a fault.
For most faults we need to send SIGSEGV with the faulting address
filled in in the struct siginfo.
Reported-by: Camm Maguire <camm@maguirefamily.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Camm Maguire <camm@maguirefamily.org>
Patchwork: https://patchwork.linux-mips.org/patch/1727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Software events are required as part of the measurable stuff by the
Linux performance counter subsystem. Here is the list of events added by
this patch:
PERF_COUNT_SW_PAGE_FAULTS
PERF_COUNT_SW_PAGE_FAULTS_MIN
PERF_COUNT_SW_PAGE_FAULTS_MAJ
PERF_COUNT_SW_ALIGNMENT_FAULTS
PERF_COUNT_SW_EMULATION_FAULTS
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Cc: a.p.zijlstra@chello.nl
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: jamie.iles@picochip.com
Acked-by: David Daney <ddaney@caviumnetworks.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Patchwork: https://patchwork.linux-mips.org/patch/1686/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The patch below updates broken web addresses in the arch directory.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
