My previous patch for init calib cfg disable a set of calibration for both
init and runtime which cause performance issue, Fix it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx params should be configured per interface.
add ieee80211_vif param to the conf_tx callback,
and change all the drivers that use this callback.
The following spatch was used:
@rule1@
struct ieee80211_ops ops;
identifier conf_tx_op;
@@
ops.conf_tx = conf_tx_op;
@rule2@
identifier rule1.conf_tx_op;
identifier hw, queue, params;
@@
conf_tx_op (
- struct ieee80211_hw *hw,
+ struct ieee80211_hw *hw, struct ieee80211_vif *vif,
u16 queue,
const struct ieee80211_tx_queue_params *params) {...}
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename the iwlagn module as iwlwifi in preparation for future
changes. Add an alias to iwlagn for backward compatibility.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add uAPSD support to mac80211. This is probably not
possible with all devices, so advertising it with
the cfg80211 flag will be left up to drivers that
want it.
Due to my previous patches it is now a fairly
straight-forward extension. Drivers need to have
accurate TX status reporting for the EOSP frame.
For drivers that buffer themselves, the provided
APIs allow releasing the right number of frames,
but then drivers need to set EOSP and more-data
themselves. This is documented in more detail in
the new code itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
both sta and lq_sta are guaranteed to be not null in the
calling function so we don't need to check them here.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we cancel a scan, the completion runs
only from the workqueue. This can cause the
remain-on-channel scan to fail when another
one was just canceled, because we're still
aborting it.
To fix this, run the completion inline with
the lock still held before returning from
iwl_scan_cancel_timeout().
Also, to avoid the scan complete work from
completing a new scan prematurely, add a
new STATUS_SCAN_COMPLETE bit.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To make the next patch easier to read, move
the function up, it'll be needed earlier in
this file in the next patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We'll need to be able to run scan complete
inline, not from the workqueue, so refactor
it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return value of iwl_scan_cancel_timeout()
isn't used anywhere, so let's just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only 5150 series devices report their temperature
in Kelvin, and for those we already convert it to
Celsius when storing into priv->temperature, so
there's no way priv->temperature will ever be in
Kelvin. Remove support for this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an AP mode interface is added with a DTIM
period of two, the slot programming is wrong.
Fix it by taking into account the DTIM period.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If iwl_scan_initiate() fails for any reason,
priv->scan_request and priv->scan_vif are left
dangling. This can lead to a crash later when
iwl_bg_scan_completed() tries to run a pending
scan request.
In practice, this seems to be very rare due to
the STATUS_SCANNING check earlier. That check,
however, is wrong -- it should allow a scan to
be queued when a reset/roc scan is going on.
When a normal scan is already going on, a new
one can't be issued by mac80211, so that code
can be removed completely. I introduced this
bug when adding off-channel support in commit
266af4c745.
Cc: stable@kernel.org [3.0]
Reported-by: Peng Yan <peng.yan@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As everybody knows kcalloc checks the multiplication is safe and
that we don't run into overflow.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the current code, the rate scaling isn't fed with
statistics from the BA notifications.
This is since my patch:
iwlagn: reclaim the packets in transport layer
Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add debugging to show the status of probe in scan notification
to help debug probe related issues
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since all the queue logic has been moved to the transport layer,
the sequence number is set in the transport layer.
While doing that I forgot that the mac header is copied to the
TB of the TX cmd in the upper layer before the call to the transport
layer. So basically we used the sequence number from mac80211...
This was fine for the first assocation but after the second, mac80211
resets its counters while we don't hence a shift that led to terrible
impact on performance.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since priv->temperature is signed, we cannot use debugfs_create_u32
to refer to it.
Use a regular debugfs file instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Txid was used without being initialized.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_trans_rx_alloc is only called from iwl_rx_init, so no need
to init the lists twice.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During my works on the transport layer I removed code that updated
a local variable (is_agg) that is needed to keep the pending_frames
count up to date. Fix this.
Also, there should be no way to have a packet with TX_CTL_AMPDU set
while the internal aggregation state machine is not in AGG_ON state.
Add a WARN_ON to ensure that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has been removed but the declaration hasn't.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This simplifies both the transport layer and the upper layer.
Kill the union in the device command, which avoids the funny syntax
we had: cmd->cmd.payload.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before this patch, the upper layer could register a callback for each
host command. This mechanism allowed the upper layer to have
different callbacks for the same command ID. In fact, it wasn't used
and the rx_handlers is enough: same callback for all the command with
a specific command ID.
The iwl_send_add_station needs the access the command that was sent
while handling the response (regardless if the command was sent in
SYNC or ASYNC mode). So now, all the handlers receive the host
command that was sent. This implies a change in the handler signature.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we're associated and want to do P2P at the same
time, the scan for remain-on-channel is currently
limited to 80ms because of the way the device will
behave in that case. Instead of doing that, split
up the dwell times into little pieces. It will not
actually be a single big dwell time then, but will
be close enough. This improves robustness of P2P
in such scenarios.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the driver split there's no more need for
shared/non-shared private station data so remove
struct iwl_station_priv_common entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the driver split there's no longer a need
to have the scan code scattered across multiple
files, so move it all back to iwl-scan.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
re-apply the unsigned shorts bug fixed by Dan Carpenter but get lost
after the file move.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Same stack corruption problem as temperature offset
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the dawn of its time, iwlwifi has used
interruptible waits to wait for synchronous
commands and firmware loading.
This leads to "interesting" bugs, because it
can't actually handle the interruptions; for
example when a command sending is interrupted
it will assume the command completed fully,
and then leave it pending, which leads to all
kinds of trouble when the command finishes
later.
Since there's no easy way to gracefully deal
with interruptions, fix the driver to not use
interruptible waits.
This at least fixes the error
iwlagn 0000:02:00.0: Error: Response NULL in 'REPLY_SCAN_ABORT_CMD'
I have seen in P2P testing, but it is likely
that there are other errors caused by this.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: stable@kernel.org [2.6.24+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For retrieve calibration hdr related information, instead of using structure in
one place and #define in other place, unify the method to use data structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 2000 series of NICs, version 2 of temperature offset calibration
should be used.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the removal of the sysfs files, it is no
longer necessary to have upper layers control
the drvdata, so let the PCI driver have it for
itself completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug_level and temperature files should be in
debugfs, the txpower file is completely unneeded
since TX power can be set with iw/iwconfig.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_suspend and iwl_resume don't exist.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's nothing PCI(E) specific in this file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The transport callbacks might as well be undefined
when CONFIG_PM_SLEEP is not set, so ifdef all of
it out and make everything available for PM_SLEEP
only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to have the transport layer have a
callback for iwl_trans_send_cmd_pdu() since it is
just a generic wrapper around iwl_trans_send_cmd().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all the PCI-E specific transport files to
be iwl-trans-pcie*; specifically iwl-trans.c
which is really iwl-trans-pcie.c.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After driver split and no need to support legacy devices, there is no reason
we need to separate the NVM access into different files, merge those.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
From time to time, we hit a WARN_ON in iwl_mac_remove_interface.
This basically means that we got out of sync with mac80211: the vif
we hold differs from the vif 80211 passes as parameter. Try to get
some data that will help to debug this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All devices use the same value for beacon_time_tsf_bits. Use the #define
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
chain_noise_num_beacons is set and never changes. Use the #define
rather than 3 levels of indirection.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The modinfo report for 135 ucode is iwlwifi-135-IWL135_UCODE_API_MAX.ucode
Change to show the value of the define: iwlwifi-135-6.ucode
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding another SKU for 6005 series devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert kzalloc to kcalloc, coalesce multiple lines too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and do a few clean up fixes on the way
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add documentation to the bus layer API - iwl-bus.h
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
enum iwl_rxon_context_id is the right type to use when we need a
rxon_context_id.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
