Sparse detected some problems in the driver, so tidy them up.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some sizes we allocate for debugfs structure are incorrect, so fix them.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hot-plugging SAS wire of direct hard disk backplane may cause disk lost. We
have done this test with several types of SATA disk from different venders,
and only two models from Seagate has this problem, ST4000NM0035-1V4107 and
ST3000VM002-1ET166.
The root cause is that the disk doesn't send D2H frame after OOB finished.
SAS controller will issue phyup interrupt only when D2H frame is received,
otherwise, will be waiting there all the time.
When this issue happen, we can find the disk again with link reset. To fix
this issue, we setup an timer after OOB finished. If the PHY is not up in
20s, do link reset. Notes: the 20s is an experience value.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS controller cannot support a programmed minimum linkrate of > 1.5G
(it will always negotiate to 1.5G at least), so just reject it.
This solves a strange situation where the PHY negotiated linkrate may be
less than the programmed minimum linkrate.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function hisi_sas_alloc(), parameter shost is not used, so remove it.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When issing a hardreset to a SATA device when running IO, it is possible
that abnormal CQs of the device are returned. Then enter error handler, it
doesn't enter function hisi_sas_abort_task() as there is no timeout IO, and
it doesn't set device as HISI_SAS_DEV_EH. So when hardreset by libata
later, it actually doesn't issue hardreset as there is a check to judge
whether device is in error.
For this situation, actually need to hardreset the device to recover.
So remove the check of sas_dev status in hisi_sas_I_T_nexus_reset().
Before we add the check to avoid the endless loop of reset for
directly-attached SATA device at probe time, actually we flutter it for
it, so it is not necessary to add the check now.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When injecting 2 bit ECC error, it will cause fatal AXI interrupts. Before
the recovery of SAS controller reset, the internal of SAS controller is in
error. If CQ interrupts return at the time, actually it is exception CQ
interrupt, and it may cause resource release in disorder.
To avoid the exception situation, shutdown AXI bus after fatal AXI
interrupt. In SAS controller reset, it will restart AXI bus. For later
version of v3 hw, hardware will shutdown AXI bus for this situation, so
just fix current ver of v3 hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Send primitive NOTIFY to SSP situation only, or it causes underflow issue
when sending IO. Also rename hisi_sas_hw.sl_notify() to hisi_sas_hw.
sl_notify_ssp().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch creates debugfs file for ITCT and adds file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sparse can detect some type casting issues in the debugfs code, so fix it
up.
Also a missing static qualifier is added to hisi_sas_debugfs_to_reg_name().
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling debugfs functions, there is no need to ever check the return
value. The function can work or not, but the code logic should never do
something different based on this.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for IOST and add file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for DQ and add file operations
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for CQ and add file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for port register and add file operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch create debugfs file for global register and add file
operations.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch takes snapshot for global regs, port regs, CQ, DQ, IOST, ITCT.
Add code for snapshot trig and generate dump directory.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch allocates snapshot memory for global reg, port regs, CQ, DQ,
IOST, ITCT.
When we fail to allocate memory for some registers, we free the memory
and set hisi_sas_debugfs_enable as 0 to stop loading debugfs from running.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch creates root directory at hisi_sas_init() and generates device
directory when we probe device driver.
And we remove the root directory at hisi_sas_exit(), but recursively
delete device directory when we remove device driver.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas. Additionally, we have
a pile of annotation, unused variable and minor updates. The big API
change is the updates for Christoph's DMA rework which include
removing the DISABLE_CLUSTERING flag. And finally there are a couple
of target tree updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXCEUNiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdjKAP9vrTTv
qFaYmAoRSbPq9ZiixaXLMy0K/6o76Uay0gnBqgD/fgn3jg/KQ6alNaCjmfeV3wAj
u1j3H7tha9j1it+4pUw=
=GDa+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas.
Additionally, we have a pile of annotation, unused variable and minor
updates.
The big API change is the updates for Christoph's DMA rework which
include removing the DISABLE_CLUSTERING flag.
And finally there are a couple of target tree updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (259 commits)
scsi: isci: request: mark expected switch fall-through
scsi: isci: remote_node_context: mark expected switch fall-throughs
scsi: isci: remote_device: Mark expected switch fall-throughs
scsi: isci: phy: Mark expected switch fall-through
scsi: iscsi: Capture iscsi debug messages using tracepoints
scsi: myrb: Mark expected switch fall-throughs
scsi: megaraid: fix out-of-bound array accesses
scsi: mpt3sas: mpt3sas_scsih: Mark expected switch fall-through
scsi: fcoe: remove set but not used variable 'port'
scsi: smartpqi: call pqi_free_interrupts() in pqi_shutdown()
scsi: smartpqi: fix build warnings
scsi: smartpqi: update driver version
scsi: smartpqi: add ofa support
scsi: smartpqi: increase fw status register read timeout
scsi: smartpqi: bump driver version
scsi: smartpqi: add smp_utils support
scsi: smartpqi: correct lun reset issues
scsi: smartpqi: correct volume status
scsi: smartpqi: do not offline disks for transient did no connect conditions
scsi: smartpqi: allow for larger raid maps
...
For v3 hw, we support DIF operation for SAS, but not SATA.
In addition, DIF CRC16 is supported.
This patchset adds the SW support for the described features. The main
components are as follows:
- Get protection mask from module param
- Fill PI fields
- Fill related to DIF in DQ and protection iu memories
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page. Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sht->sg_tablesize is set in the driver, and it will be assigned to
shost->sg_tablesize in SCSI mid-layer. So it is not necessary to assign
shost->sg_table one more time in the driver.
In addition to the change, change each scsi_host_template.sg_tablesize
to HISI_SAS_SGE_PAGE_CNT instead of SG_ALL.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Relocate the codes related to dma_map/unmap in hisi_sas_task_prep() to
reduce complexity, with a view to add DIF/DIX support.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patchset fixes some warnings detected by the sparse tool, like these:
drivers/scsi/hisi_sas/hisi_sas_main.c:1469:52: warning: incorrect type in assignment (different base types)
drivers/scsi/hisi_sas/hisi_sas_main.c:1469:52: expected unsigned short [unsigned] [assigned] [usertype] tag_of_task_to_be_managed
drivers/scsi/hisi_sas/hisi_sas_main.c:1469:52: got restricted __le16 [usertype] <noident>
drivers/scsi/hisi_sas/hisi_sas_main.c:1723:52: warning: incorrect type in assignment (different base types)
drivers/scsi/hisi_sas/hisi_sas_main.c:1723:52: expected unsigned short [unsigned] [assigned] [usertype] tag_of_task_to_be_managed
drivers/scsi/hisi_sas/hisi_sas_main.c:1723:52: got restricted __le16 [usertype] <noident>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the time of SAS SSP connection is 1ms, which means the link
connection will fail if no IO response after this period.
For some disks handling large IO (such as 512k), 1ms is not enough, so
change it to 5ms.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function hisi_sas_task_prep(), we check asd_sas_port, but in function
hisi_sas_task_exec(), we already refer to asd_sas_port by using function
dev_to_hisi_hba() implicitly. So to avoid this possible invalid
dereference, relocate the check to function hisi_sas_task_prep().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If INT_COAL_EN is enabled, configure time and count of interrupt
coalescing. Then if CQ collects count of CQ entries in time, it will
report the interrupt. Or if CQ doesn't collect enough CQ entries in time,
it will report the interrupt at timeout.
As all the registers are not supported to be changed dynamically, we need
to config those register between disable and enable PHYs.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If CQ_INT_CONVERGE_EN is enabled, the interrupts of all the 16 CQ queues
will be reported by CQ0.
So we need to change the process of CQ tasklet for this situation.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently all the three HBA (v1/v2/v3 HW) share the same host attributes.
To support each HBA having separate attributes in future, create per-HBA
attributes.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API. Switch it over to the better generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/hisi_sas/hisi_sas_v1_hw.c: In function 'start_delivery_v1_hw':
drivers/scsi/hisi_sas/hisi_sas_v1_hw.c:907:20: warning:
variable 'dq_list' set but not used [-Wunused-but-set-variable]
drivers/scsi/hisi_sas/hisi_sas_v2_hw.c: In function 'start_delivery_v2_hw':
drivers/scsi/hisi_sas/hisi_sas_v2_hw.c:1671:20: warning:
variable 'dq_list' set but not used [-Wunused-but-set-variable]
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c: In function 'start_delivery_v3_hw':
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:889:20: warning:
variable 'dq_list' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit
fa222db0b0 ("scsi: hisi_sas: Don't lock DQ for complete task sending")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a NULL pointer dereference in case *slot* happens to be NULL at
lines 1053 and 1878:
struct hisi_sas_cq *cq =
&hisi_hba->cq[slot->dlvry_queue];
Notice that *slot* is being NULL checked at lines 1057 and 1881:
if (slot), which implies it may be NULL.
Fix this by placing the declaration and definition of variable cq, which
contains the pointer dereference slot->dlvry_queue, after slot has been
properly NULL checked.
Addresses-Coverity-ID: 1474515 ("Dereference before null check")
Addresses-Coverity-ID: 1474520 ("Dereference before null check")
Fixes: 584f53fe5f ("scsi: hisi_sas: Fix the race between IO completion and timeout for SMP/internal IO")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently a spin_unlock_irqrestore() call is missing on the error path,
so add it.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update registers as follows:
- Default value of AIP timer is 1ms, and it is easy for some expanders to
cause IO error. Change the value to max value 65ms to avoid IO error for
those expanders.
- A CQ completion will be reported by HW when 4 CQs have occurred or the
aging timer expires, whichever happens first. Sor serial IO scenario, it
will still wait 8us for every IO before it is reported. So in the
situation, the performance is poor. So to improve it, change the limit
time to the least value.
For other scenario, it does little affect to the performance.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we use the IPTT defined in LLDD to identify IOs. Actually for
IOs which are from the block layer, they have tags to identify them. So
for those IOs, use tag of the block layer directly, and for IOs which is
not from the block layer (such as internal IOs from libsas/LLDD), reserve
96 IPTTs for them.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The interrupts of ent72 and ent74 are not processed by PCIe AER handling,
so we need to unmask the interrupts and process them first in the driver.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an SSP/SMP IO times out, it may be actually in reality be
simultaneously processing completion of the slot in
slot_complete_vx_hw().
Then if the slot is freed in slot_complete_vx_hw() (this IPTT is freed
and it may be re-used by other slot), and we may abort the wrong slot in
hisi_sas_abort_task().
So to solve the issue, free the slot after the check of
SAS_TASK_STATE_ABORTED in slot_complete_vx_hw().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If SMP/internal IO times out, we will possibly free the task immediately.
However if the IO actually completes at the same time, the IO completion
may refer to task which has been freed.
So to solve the issue, flush the tasklet to finish IO completion before
free'ing slot/task.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In evaluating hisi_hba, the sas_port may be NULL, so for safety relocate
the the check to value possible NULL deference.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
At directly attached situation, if the user modifies the sysfs interface
of maximum_linkrate and minimum_linkrate to renegotiate the linkrate
between SAS controller and target, the value of both files mentioned
above should have change to user setting after renegotiate is over, but
it remains unchanged.
To fix this bug, maximum_linkrate and minimum_linkrate will be directly
fed back to relevant sas_phy structure.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now LLDDs have to implement lldd_port_deformed method otherwise NULL
dereference will happen. Make it optional and remove the dummy implementation
in hisi_sas.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Acked-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a check ERR bit of status to decide whether there is something wrong
with initial register-D2H FIS. If error exist, PHY link reset the channel
to restart OOB.
Directly call work HISI_PHYE_LINK_RESET replacing disable_phy_vx_hw() and
enable_phy_vx_hw().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In task start delivery function, we need to add a memory barrier to prevent
re-ordering of reading memory by hardware. Because the slot data is set in
task prepare function and it could be running in another CPU.
This patch adds an memory barrier after s->ready is read in the task start
delivery function, and uses WRITE_ONCE() in the places where s->ready is
set to ensure that the compiler does not re-order.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To decrease the usage of spinlock during delivery IO, relocate some code in
hisi_sas_task_prep().
Also an invalid comment is removed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch implements handlers of PCIe FLR for v3 hw, reset_prepare() and
reset_done().
User can issue FLR through sysfs interface, as v3 hw support PCIe FLR.
Then if we don't implement these two handlers, our SAS controller will not
work after executing FLR.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Much code of PM suspend function also exists in soft reset function. This
is not concise. So, this patch relocates the common code of these two
functions to a separate function.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch tidies host controller reset function by putting some code to
two new functions, and exports these two functions out, so that they could
be used by FLR feature to be realised.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is an issue that link reset can't recover PHY when STP link timeout.
Because current process of enabling PHY for v3 hw will wait last
transmission done. The time of one transmission depends IO size, disk model
and so on. Normally, it should be shorter than 50ms. But the last
transmission could be never done for some abnormal scenarios, such as STP
link timeout.
This patch is to fix the issue. Check PHY status after starting process of
enabling PHY for 50ms. If the PHY is still active, we disable it forcibly
by PHY reset. Of course, we need to clear the PHY reset bit when enable
PHY.
Besides, the function disable_phy_v3_hw() should not be suitable to call in
interrupts for hilink bug for this 50ms delay. Then, we do link reset for
hilink bug directly. The change is that we don't clear the invalid dword
count register. This is better. Because we should not clear such error
count while not saved.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ISR of channel interrupt of v3 hw is a little long and messy. This
patch tidies it by relocating CHL_INT1 and CHL_INT2 handling to new
function separately.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
