gfar_halt() and gfar_start() are responsible for stopping
and starting the DMA and the Rx/Tx hw rings. They implement
the support for the "graceful Rx/Tx stop/start" hw procedure,
and also disable/enable eTSEC's hw interrupts in the process.
The GRS/GTS procedure requires however to have the RQUEUE/TQUEUE
registers cleared first and to wait for a period of time for the
current frame to pass through the interface (around ~10ms for a
jumbo frame). Only then may the GTS and GRS bits from DMACTRL be
set to shut down the DMA, and finally the Tx_EN and Rx_EN bits in
MACCFG1 may be cleared to disable the Tx/Rx blocks.
The same register programming order applies to start the Rx/Tx:
enabling the RQUEUE/TQUEUE *before* clearing the GRS/GTS bits.
This is a HW recommendation in order to avoid a possible
controller "lock up" during graceful reset.
Cleanup the gfar_halt()/start() prototypes, to take priv instead
of ndev as their purpose is to operate on HW. Enabling the
RQUEUE/TQUEUE in the hw_init() is not needed anymore since
that's the job of gfar_start().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Throughout the code there are places where the controller's
hw interrupt sources need to get disabled/enabled (masked/
un-masked) all at once. The recommendation for disabling
the interrupts is to clear the ievent first then the imask
register (not the other way around).
Use the gfar_ints_enable/disable() helpers to make these
operations consistent.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RCTRL updates of the FSL_GIANFAR_DEV_HAS_PADDING device
flag get overriden by the FSL_GIANFAR_DEV_HAS_TIMER flag
settings, which impose a Rx padding alignment of 8 bytes.
As all the eTSEC devices that set HAS_PADDING also set the
HAS_TIMER flag, the HAS_PADDING flag is now obsolete.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing the sysfs stubs for the Tx FIFOCFG and ATTRELI
(stashing) config registers, as these registers may only
be configured after a MAC reset, with the controller stopped
(i.e. during hw init, at probe() time). The current sysfs
stubs allow on-the-fly updates of these registers (the locking
measures are useless and only add unecessary code).
Changing these registers is discouraged. Only the default values
will be used instead.
Moreover, the stashing (ATTRELI) configuration options were
effectively disabled (didn't get to the hw anyway if changed)
because the stashing device_flags (HAS_BD_STASHING|HAS_BUF_STASHING)
were "accidentally" cleared during probe().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out gfar_hw_init() to contain all the controller hw
initialization steps for a better control of register writes,
and to significantly simplify the tangled code from gfar_probe().
This results in code size and stack usage reduction (besides
code readability).
Fix memory leak on device removal, by freeing the rx_/tx_queue
structures.
Replace custom bit swapping function with a library one (bitrev8).
Move allocation of rx_/tx_queue struct arrays before the group
structure init, because in order to assign Rx/Tx queues
to groups we need to have the queues first. This also allows
earlier bail out of gfar_probe(), in case the memory allocation
fails.
The flow control checks for maccfg1 were removed from gfar_probe(),
since flow control is disabled at probe time (priv->rx_/tx_pause_en
are 0). Redundant initializations (by 0) also removed.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes unhandled register write in gianfar_ethtool.c.
Fixes following endianess related functional issues,
reported by sparse as well, i.e.:
gianfar_ethtool.c:1058:33: warning:
incorrect type in argument 1 (different base types)
expected unsigned int [unsigned] [usertype] value
got restricted __be32 [usertype] ip4src
gianfar_ethtool.c:1164:33: warning:
restricted __be16 degrades to integer
gianfar_ethtool.c:1669:32: warning:
invalid assignment: ^=
left side has type restricted __be16
right side has type int
Solves all the sparse warnings for mixig normal pointers
with __iomem pointers for gianfar_ptp.c, i.e.:
gianfar_ptp.c:163:32: warning:
incorrect type in argument 1 (different address spaces)
expected unsigned int [noderef] <asn:2>*addr
got unsigned int *<noident>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to keep DT compatibility we need to revert this, otherwise the original
dts files will no longer work with this driver change.
This reverts commit 7a399e3a2e.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not assume that the PHY reset is always active low.
Retrieve this information from the device tree instead, so that the PHY reset
can work on both cases.
Reported-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_tx_timestamp(skb) should be called _before_ TX completion
has a chance to trigger, otherwise it is too late and we access
freed memory.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: de5fb0a053 ("net: fec: put tx to napi poll function to fix dead lock")
Cc: Frank Li <Frank.Li@freescale.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 031916568a worked around
errata ERR006358, but comment contains duplicated lines, impairing
the readability. Remove them.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
SIOCGHWTSTAMP ioctl
1. Add the SIOCGHWTSTAMP ioctl and update the timestamping
documentation.
2. Implement SIOCGHWTSTAMP in most drivers that support SIOCSHWTSTAMP.
3. Add a test program to exercise SIOC{G,S}HWTSTAMP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On tx submit the driver always dma_map_single() FEC_ENET_TX_FRSIZE (=2048)
bytes. This works because we don't overwrite any memory after the data buffer,
we remove it from cache if it was there. So we hurt performace in case the
mapping of a smaller area makes a difference.
There is also a bug: If the data area starts shortly before the end of
RAM say 0xc7fffa10 and the RAM ends at 0xc8000000 then we have enough
space to fit the data area (according to skb->len) but we would map beyond
end of ram if we are using 2048. In v2.6.31 (against which kernel this patch
made) there is the following check in dma_cache_maint():
|BUG_ON(!virt_addr_valid(start) || !virt_addr_valid(start + size - 1));
Since the area starting at 0xc8000000 is no longer virt_addr_valid() we
BUG() during dma_map_single(). The BUG() statement was removed in v3.5-rc1 as
per 2dc6a016 ("ARM: dma-mapping: use asm-generic/dma-mapping-common.h").
This patch was tested on v2.6.31 and then forward-ported and compile
tested only against the net tree. I think it is still worth fixing
mainline even after the BUG() statement is gone.
Tested-by: Fugang Duan <B38611@freescale.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver fails to check the results of DMA mapping and results in
the following warning: (with kernel config "CONFIG_DMA_API_DEBUG" enable)
------------[ cut here ]------------
WARNING: at lib/dma-debug.c:937 check_unmap+0x43c/0x7d8()
fec 2188000.ethernet: DMA-API: device driver failed to check map
error[device address=0x00000000383a8040] [size=2048 bytes] [mapped as single]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.17-16827-g9cdb0ba-dirty #188
[<80013c4c>] (unwind_backtrace+0x0/0xf8) from [<80011704>] (show_stack+0x10/0x14)
[<80011704>] (show_stack+0x10/0x14) from [<80025614>] (warn_slowpath_common+0x4c/0x6c)
[<80025614>] (warn_slowpath_common+0x4c/0x6c) from [<800256c8>] (warn_slowpath_fmt+0x30/0x40)
[<800256c8>] (warn_slowpath_fmt+0x30/0x40) from [<8026bfdc>] (check_unmap+0x43c/0x7d8)
[<8026bfdc>] (check_unmap+0x43c/0x7d8) from [<8026c584>] (debug_dma_unmap_page+0x6c/0x78)
[<8026c584>] (debug_dma_unmap_page+0x6c/0x78) from [<8038049c>] (fec_enet_rx_napi+0x254/0x8a8)
[<8038049c>] (fec_enet_rx_napi+0x254/0x8a8) from [<804dc8c0>] (net_rx_action+0x94/0x160)
[<804dc8c0>] (net_rx_action+0x94/0x160) from [<8002c758>] (__do_softirq+0xe8/0x1d0)
[<8002c758>] (__do_softirq+0xe8/0x1d0) from [<8002c8e8>] (do_softirq+0x4c/0x58)
[<8002c8e8>] (do_softirq+0x4c/0x58) from [<8002cb50>] (irq_exit+0x90/0xc8)
[<8002cb50>] (irq_exit+0x90/0xc8) from [<8000ea88>] (handle_IRQ+0x3c/0x94)
[<8000ea88>] (handle_IRQ+0x3c/0x94) from [<8000855c>] (gic_handle_irq+0x28/0x5c)
[<8000855c>] (gic_handle_irq+0x28/0x5c) from [<8000de00>] (__irq_svc+0x40/0x50)
Exception stack(0x815a5f38 to 0x815a5f80)
5f20: 815a5f80 3b9aca00
5f40: 0fe52383 00000002 0dd8950e 00000002 81e7b080 00000000 00000000 815ac4d8
5f60: 806032ec 00000000 00000017 815a5f80 80059028 8041fc4c 60000013 ffffffff
[<8000de00>] (__irq_svc+0x40/0x50) from [<8041fc4c>] (cpuidle_enter_state+0x50/0xf0)
[<8041fc4c>] (cpuidle_enter_state+0x50/0xf0) from [<8041fd94>] (cpuidle_idle_call+0xa8/0x14c)
[<8041fd94>] (cpuidle_idle_call+0xa8/0x14c) from [<8000edac>] (arch_cpu_idle+0x10/0x4c)
[<8000edac>] (arch_cpu_idle+0x10/0x4c) from [<800582f8>] (cpu_startup_entry+0x60/0x130)
[<800582f8>] (cpu_startup_entry+0x60/0x130) from [<80bc7a48>] (start_kernel+0x2d0/0x328)
[<80bc7a48>] (start_kernel+0x2d0/0x328) from [<10008074>] (0x10008074)
---[ end trace c6edec32436e0042 ]---
Because dma-debug add new interfaces to debug dma mapping errors, pls refer
to: http://lwn.net/Articles/516640/
After dma mapping, it must call dma_mapping_error() to check mapping error,
otherwise the map_err_type alway is MAP_ERR_NOT_CHECKED, check_unmap() define
the mapping is not checked and dump the error msg. So,add dma_mapping_error()
checking to fix the WARNING
And RX DMA buffers are used repeatedly and the driver copies it into an skb,
fec_enet_rx() should not map or unmap, use dma_sync_single_for_cpu()/dma_sync_single_for_device()
instead of dma_map_single()/dma_unmap_single().
There have another potential issue: fec_enet_rx() passes the DMA address to __va().
Physical and DMA addresses are *not* the same thing. They may differ if the device
is behind an IOMMU or bounce buffering was required, or just because there is a fixed
offset between the device and host physical addresses. Also fix it in this patch.
=============================================
V2: add net_ratelimit() to limit map err message.
use dma_sync_single_for_cpu() instead of dma_map_single().
fix the issue that pass DMA addresses to __va() to get virture address.
V1: initial send
=============================================
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) The addition of nftables. No longer will we need protocol aware
firewall filtering modules, it can all live in userspace.
At the core of nftables is a, for lack of a better term, virtual
machine that executes byte codes to inspect packet or metadata
(arriving interface index, etc.) and make verdict decisions.
Besides support for loading packet contents and comparing them, the
interpreter supports lookups in various datastructures as
fundamental operations. For example sets are supports, and
therefore one could create a set of whitelist IP address entries
which have ACCEPT verdicts attached to them, and use the appropriate
byte codes to do such lookups.
Since the interpreted code is composed in userspace, userspace can
do things like optimize things before giving it to the kernel.
Another major improvement is the capability of atomically updating
portions of the ruleset. In the existing netfilter implementation,
one has to update the entire rule set in order to make a change and
this is very expensive.
Userspace tools exist to create nftables rules using existing
netfilter rule sets, but both kernel implementations will need to
co-exist for quite some time as we transition from the old to the
new stuff.
Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have
worked so hard on this.
2) Daniel Borkmann and Hannes Frederic Sowa made several improvements
to our pseudo-random number generator, mostly used for things like
UDP port randomization and netfitler, amongst other things.
In particular the taus88 generater is updated to taus113, and test
cases are added.
3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet
and Yang Yingliang.
4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin
Sujir.
5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet,
Neal Cardwell, and Yuchung Cheng.
6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary
control message data, much like other socket option attributes.
From Francesco Fusco.
7) Allow applications to specify a cap on the rate computed
automatically by the kernel for pacing flows, via a new
SO_MAX_PACING_RATE socket option. From Eric Dumazet.
8) Make the initial autotuned send buffer sizing in TCP more closely
reflect actual needs, from Eric Dumazet.
9) Currently early socket demux only happens for TCP sockets, but we
can do it for connected UDP sockets too. Implementation from Shawn
Bohrer.
10) Refactor inet socket demux with the goal of improving hash demux
performance for listening sockets. With the main goals being able
to use RCU lookups on even request sockets, and eliminating the
listening lock contention. From Eric Dumazet.
11) The bonding layer has many demuxes in it's fast path, and an RCU
conversion was started back in 3.11, several changes here extend the
RCU usage to even more locations. From Ding Tianhong and Wang
Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav
Falico.
12) Allow stackability of segmentation offloads to, in particular, allow
segmentation offloading over tunnels. From Eric Dumazet.
13) Significantly improve the handling of secret keys we input into the
various hash functions in the inet hashtables, TCP fast open, as
well as syncookies. From Hannes Frederic Sowa. The key fundamental
operation is "net_get_random_once()" which uses static keys.
Hannes even extended this to ipv4/ipv6 fragmentation handling and
our generic flow dissector.
14) The generic driver layer takes care now to set the driver data to
NULL on device removal, so it's no longer necessary for drivers to
explicitly set it to NULL any more. Many drivers have been cleaned
up in this way, from Jingoo Han.
15) Add a BPF based packet scheduler classifier, from Daniel Borkmann.
16) Improve CRC32 interfaces and generic SKB checksum iterators so that
SCTP's checksumming can more cleanly be handled. Also from Daniel
Borkmann.
17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces
using the interface MTU value. This helps avoid PMTU attacks,
particularly on DNS servers. From Hannes Frederic Sowa.
18) Use generic XPS for transmit queue steering rather than internal
(re-)implementation in virtio-net. From Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
random32: add test cases for taus113 implementation
random32: upgrade taus88 generator to taus113 from errata paper
random32: move rnd_state to linux/random.h
random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized
random32: add periodic reseeding
random32: fix off-by-one in seeding requirement
PHY: Add RTL8201CP phy_driver to realtek
xtsonic: add missing platform_set_drvdata() in xtsonic_probe()
macmace: add missing platform_set_drvdata() in mace_probe()
ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe()
ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh
vlan: Implement vlan_dev_get_egress_qos_mask as an inline.
ixgbe: add warning when max_vfs is out of range.
igb: Update link modes display in ethtool
netfilter: push reasm skb through instead of original frag skbs
ip6_output: fragment outgoing reassembled skb properly
MAINTAINERS: mv643xx_eth: take over maintainership from Lennart
net_sched: tbf: support of 64bit rates
ixgbe: deleting dfwd stations out of order can cause null ptr deref
ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS
...
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
Replace some instances of of_irq_map_one()/irq_create_of_mapping() and
of_irq_to_resource() by the simpler equivalent irq_of_parse_and_map().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely: resolved conflicts with core code renames]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Under certain low traffic conditions, the single core
devices with multiple Rx/Tx queues (MQ mode) may reach
soft lockup due to gfar_poll not returning in proper time.
The following exception was obtained using iperf on a 100Mbit
half-duplex link, for a p1010 single core device:
BUG: soft lockup - CPU#0 stuck for 23s! [iperf:2847]
Modules linked in:
CPU: 0 PID: 2847 Comm: iperf Not tainted 3.12.0-rc3 #16
task: e8bf8000 ti: eeb16000 task.ti: ee646000
NIP: c0255b6c LR: c0367ae8 CTR: c0461c18
REGS: eeb17e70 TRAP: 0901 Not tainted (3.12.0-rc3)
MSR: 00029000 <CE,EE,ME> CR: 44228428 XER: 20000000
GPR00: c0367ad4 eeb17f20 e8bf8000 ee01f4b4 00000008 ffffffff ffffffff
00000000
GPR08: 000000c0 00000008 000000ff ffffffc0 000193fe
NIP [c0255b6c] find_next_bit+0xb8/0xc4
LR [c0367ae8] gfar_poll+0xc8/0x1d8
Call Trace:
[eeb17f20] [c0367ad4] gfar_poll+0xb4/0x1d8 (unreliable)
[eeb17f70] [c0422100] net_rx_action+0xa4/0x158
[eeb17fa0] [c003ec6c] __do_softirq+0xcc/0x17c
[eeb17ff0] [c000c28c] call_do_softirq+0x24/0x3c
[ee647cc0] [c0004660] do_softirq+0x6c/0x94
[ee647ce0] [c003eb9c] local_bh_enable+0x9c/0xa0
[ee647cf0] [c0454fe8] tcp_prequeue_process+0xa4/0xdc
[ee647d10] [c0457e44] tcp_recvmsg+0x498/0x96c
[ee647d80] [c047b630] inet_recvmsg+0x40/0x64
[ee647da0] [c040ca8c] sock_recvmsg+0x90/0xc0
[ee647e30] [c040edb8] SyS_recvfrom+0x98/0xfc
To prevent this, the outer while() loop has been removed
allowing gfar_poll() to return faster even if there's
still budget left. Also, there's no need to recompute
the budget per Rx queue anymore.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Enable workaround for P2020/P2010 erratum eTSEC 20,
"Excess delays when transmitting TOE=1 large frames".
The impact is that frames lager than 2500-bytes for which
TOE (i.e. TCP/IP hw accelerations like Tx csum) is enabled
may see excess delay before start of transmission.
This erratum was fixed in Rev 2.0.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the macros and defines from mpc85xx.h to simplify
and prevent errors in identifying a mpc85xx based SoC
for errata detection.
This should help enabling (and identifying) workarounds
for various mpc85xx based chips and revisions.
For instance, express MPC8548 Rev.2 as:
(SVR_SOC_VER(svr) == SVR_8548) && (SVR_REV(svr) == 0x20)
instead of:
(pvr == 0x80210020 && mod == 0x8030 && rev == 0x0020)
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A002 is still in "no plans to fix" state, and applies to all
the current P1/P2 parts as well, so it's resonable to enable
its workaround by default, for all the soc's with etsec.
The impact of not enabling this workaround for affected parts
is that under certain conditons (runt frames or even frames
with RX error detected at PHY level) during controller reset,
the controller might fail to indicate Rx reset (GRS) completion.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/usb/qmi_wwan.c
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
include/net/netfilter/nf_conntrack_synproxy.h
include/net/secure_seq.h
The conflicts are of two varieties:
1) Conflicts with Joe Perches's 'extern' removal from header file
function declarations. Usually it's an argument signature change
or a function being added/removed. The resolutions are trivial.
2) Some overlapping changes in qmi_wwan.c and be.h, one commit adds
a new value, another changes an existing value. That sort of
thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.
For instance:
fsl,cksel = <0>;
for using external (TSEC_TMR_CLK input) high precision timer
reference clock.
Other acceptable values:
<1> : eTSEC system clock
<2> : eTSEC1 transmit clock
<3> : RTC clock input
When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 894116bd0e.
I applied the wrong version of this patch, correct
version coming up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.
For instance:
fsl,cksel = <0>;
for using external (TSEC_TMR_CLK input) high precision timer
reference clock.
Other acceptable values:
<1> : eTSEC system clock
<2> : eTSEC1 transmit clock
<3> : RTC clock input
When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/freescale/fec_main.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
net/bridge/br_multicast.c
net/ipv6/sit.c
The conflicts were minor:
1) sit.c changes overlap with change to ip_tunnel_xmit() signature.
2) br_multicast.c had an overlap between computing max_delay using
msecs_to_jiffies and turning MLDV2_MRC() into an inline function
with a name using lowercase instead of uppercase letters.
3) stmmac had two overlapping changes, one which conditionally allocated
and hooked up a dma_cfg based upon the presence of the pbl OF property,
and another one handling store-and-forward DMA made. The latter of
which should not go into the new of_find_property() basic block.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug: error to get the previous BD entry. When the current BD
is the first BD, the previous BD entry must be the last BD,
not "bdp - 1" in current logic.
V4:
* Optimize fec_enet_get_nextdesc() for code clean.
Replace "ex_new_bd - ring_size" with "ex_base".
Replace "new_bd - ring_size" with "base".
V3:
* Restore the API name because David suggest to use fec_enet_
prefix for all function in fec driver.
So, change next_bd() -> fec_enet_get_nextdesc()
change pre_bd() -> fec_enet_get_prevdesc()
* Reduce the two APIs parameters for easy to call.
V2:
* Add tx_ring_size and rx_ring_size to struct fec_enet_private.
* Replace api fec_enet_get_nextdesc() with next_bd().
Replace api fec_enet_get_prevdesc() with pre_bd().
* Move all ring size check logic to next_bd() and pre_bd(), which
simplifies the code redundancy.
V1:
* Add BD ring size check to get the previous BD entry in correctly.
Reviewed-by: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <frank.li@freescale.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the amount of sent bytes reported to BQL by reporting the
number of bytes on wire in the xmit routine, and recording that
value for each skb in order to be correctly confirmed on Tx
confirmation cleanup.
Reporting skb->len to BQL just before exiting xmit is not correct
due to possible insertions of TOE block and alignment bytes in the
skb->data, which are being stripped off by the controller before
transmission on wire. This led to mismatch of (incorrectly)
reported bytes to BQL b/w xmit and Tx confirmation, resulting in
Tx timeout firing, for the h/w tx timestamping acceleration case.
There's no easy way to obtain the number of bytes on wire in the Tx
confirmation routine, so skb->cb is used to convey that information
from xmit to Tx confirmation, for now (as proposed by Eric). Revived
the currently unused GFAR_CB() construct for that purpose.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dc975382 "net: fec: add napi support to improve proformance"
converted the fec driver to the napi model. However, that commit
forgot to remove the call to skb_defer_rx_timestamp which is only
needed in non-napi drivers.
(The function napi_gro_receive eventually calls netif_receive_skb,
which in turn calls skb_defer_rx_timestamp.)
This patch should also be applied to the 3.9 and 3.10 kernels.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complains that on some arches unsigned longs can be 8
characters which is larger than the buffer is only 6 chars.
Additionally, Ben Hutchings points out that the buffer actually holds
big endian data and the buffer we are reading from is CPU endian.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a custom 'FEC_NAPI_WEIGHT', just use the generic
'NAPI_POLL_WEIGHT' definition instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
make the Freescale ethernet driver get, prepare and enable the FEC clock
during probe(); disable and unprepare the clock upon remove(), put is
done by the devm approach; hold a reference to the clock over the period
of use.
clock lookup is non-fatal as not all platforms provide clock specs in
their device tree; failure to enable specified clocks is fatal.
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 720a43efd3
(drivers:net: Remove unnecessary OOM messages after netdev_alloc_skb)
there is a build warning:
drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c: In function 'tx_skb_align_workaround':
drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c:586:26: warning: unused variable 'fep'
Fix it.
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &ofdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eTSEC has Rx and Tx flow control capabilities that may be enabled
through MACCFG1[Rx_Flow, Tx_Flow] bits. These bits must not be set
however when eTSEC is operated in Half-Duplex mode. Unfortunately,
the driver currently sets these bits unconditionally.
This patch adds the proper handling of the PAUSE frame capability
register bits by implementing the ethtool -A interface. When pause
autoneg is enabled, the controller uses the phy's capability to
negotiate PAUSE frame settings with the link partner and reconfigures
its Rx_Flow and Tx_Flow settings to match the capabilities of the
link partner. If pause autoneg is off, the PAUSE frame generation
may be forced manually (ethtool -A). Flow control is disabled by
default now.
This implementation is inspired by the tg3 driver.
Signed-off-by: Lutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup gfar_start_xmit()'s fast path by factoring out "redundant"
FCB insertion code (repeated gfar_add_fcb() calls and related)
and by reducing the number of if() clauses (i.e. if(fcb) checks).
Improve maintainability (e.g. there's less code and easier to read)
also by introducing do_csum and do_vlan to mark the other 2 Tx TOE
functionalities, following the same model as do_tstamp.
fcb_len may also be 0 now, to mark that Tx FCB insertion conditions
(do_csum, do_vlan, do_tstamp) have not been met.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both [eTSEC76] and [eTSEC12] errata relate to Tx checksum generation
(for some MPC83xx and MCP8548 older revisions). They require the same
workaround: manual checksum computation and insertion, and disabling
the H/W Tx csum acceleration feature (per frame) through Tx FCB
(Frame Control Block) csum offload settings.
The workaround for [eTSEC76] needs to be fixed because it currently
fails to disable H/W Tx csum insertion via FCB. This patch fixes it
and provides a common workaround implementation for both Tx csum errata.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
grp->grp_id is obsolete. It has no use in the current driver.
Remove it from gfar_priv_grp and put the 'rstat' member
in its place, in the 2nd cache line, as rstat needs fast access.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't test for having link and let hardware deal with this situation.
Without this patch I see a machine running an -rt patched Linux being
stuck in sch_direct_xmit when it looses link while there is still a
packet to be sent. In this case the fec_enet_start_xmit routine returned
NETDEV_TX_BUSY which makes the network stack reschedule the packet and
so sch_direct_xmit calls fec_enet_start_xmit again.
I failed to reproduce a complete hang without -rt, but I think the
problem exists there, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ready bit in the transmit buffer descriptor (TxBD[R])
is previously detected as not set during a prior frame transmission,
then the ENET_TDAR[TDAR] bit is cleared at a later time, even if
additional TxBDs were added to the ring and the ENET_TDAR[TDAR]
bit is set. This results in frames not being transmitted until
there is a 0-to-1 transition on ENET_TDAR[TDAR].
Workarounds:
code can use the transmit frame interrupt flag (ENET_EIR[TXF])
as a method to detect whether the ENET has completed transmission
and the ENET_TDAR[TDAR] has been cleared. If ENET_TDAR[TDAR] is
detected as cleared when packets are queued and waiting for transmit,
then a write to the TDAR bit will restart TxBD processing.
This case main happen when loading is light. A ethernet package may
not send out utile next package put into tx queue.
How to test:
while [ true ]
do
ping <IP> -s 10000 -w 4
ping <IP> -s 6000 -w 2
ping <IP> -s 4000 -w 2
ping <IP> -s 10000 -w 2
done
You will see below result in overnight test.
6008 bytes from 10.192.242.116: seq=1 ttl=128 time=0.722 ms
4008 bytes from 10.192.242.116: seq=0 ttl=128 time=1001.008 ms
4008 bytes from 10.192.242.116: seq=1 ttl=128 time=1.010 ms
10008 bytes from 10.192.242.116: seq=0 ttl=128 time=0.896 ms
After apply this patch, >1000ms delay disappear.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MODULE_ALIAS, so that auto module loading can work.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using devm_request_irq() can make the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As devm_ioremap_resource() is used, there is no need to explicitely check the
return value from platform_get_resource(), as this is something that
devm_ioremap_resource() takes care by itself.
Also, place platform_get_resource() prior to devm_ioremap_resource() for
better code readability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_ptp should also be enabled in fec_resume() and disabled in fec_suspend().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On fec_probe the clocks are enabled in the following order:
clk_ahb -> clk_ipg -> clk_enet_out -> clk_ptp
, so in the error and remove paths we should disabled them in the opposite
order.
Also fix the order in the suspend/resume functions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_enet_out and clk_ptp are optional clocks, so we should not enable/disable
them unconditionally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables the driver to take advantage of the FEC VLAN
indicator to improve performance.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 38ae92d "fec: Add support for reading
RMON registers" causes the imx6Q to crash.
This fixes it by only enabling the RMON registers, the
registers are already cleared by the MAC being reset.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_bytes field was not being updated so the
network card statistics showed 0.0B transmitted.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setup the multicast list of the net_device instead of
clearing it blindly. This restores the multicast groups
in case of a link down/up event or when resuming from
suspend.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool operation to read RMON registers.
Tested against net-next on i.MX28.
v2: make conditional on #ifndef CONFIG_M5272
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers that select MII also need to select NET_CORE because MII
depends on it. This is a bit ridiculous because NET_CORE is just a
menu option that doesn't enable any code by itself.
There is also no need for it to be a visible option, since its users
all select it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits 4c09eed9 (net: fec: Enable imx6 enet checksum acceleration) and
baa70a5c (net: fec: enable pause frame to improve rx prefomance for 1G
network) introduced functionality into the FEC driver which is not
supported on MCF5272. The registers used to implement this functionality
do not exist on MCF5272. Since register defines for MCF5272 are separate
from register defines for other chips, building images for MCF5272 fails
as follows.
fec_main.c: In function 'fec_restart':
fec_main.c:520:8: error: 'FEC_RACC' undeclared (first use in this function)
fec_main.c:585:3: error: 'FEC_R_FIFO_RSEM' undeclared (first use in this function)
fec_main.c:586:3: error: 'FEC_R_FIFO_RSFL' undeclared (first use in this function)
fec_main.c:587:3: error: 'FEC_R_FIFO_RAEM' undeclared (first use in this function)
fec_main.c:588:3: error: 'FEC_R_FIFO_RAFL' undeclared (first use in this function)
fec_main.c:591:3: error: 'FEC_OPD' undeclared (first use in this function)
Adding the missing register defines is not an option, since the registers
do not exist on MCF5272. Disable the added functionality for MCF5272 builds.
Cc: Frank Li <Frank.Li@freescale.com>
Cc: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool operation to restart autonegotiation via the PHY.
Tested on i.MX28EVK.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older Single Queue (SQ_SG_MODE) devices like TSEC (i.e. mpc83xx)
don't feature the frame receive indication bits (RXF) in RSTAT.
For these and for the rest of the SQ_SG_MODE devices, provide the
appropiate polling routine that handles a single pair of Rx/Tx
BD rings, removing the overhead incurred by the multiple queues/
multiple interrupt group devices (veTSEC/ eTSEC2.0 devices).
So this is primarily a fix for the TSEC devices.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 75096579c3 ("lib: devres: Introduce devm_ioremap_resource()")
introduced devm_ioremap_resource() and deprecated the use of
devm_request_and_ioremap().
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
CC: netdev@vger.kernel.org
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing pdev in fec_ptp_init() is enough, since we can get ndev locally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
If no valid MAC address could be obtained from the hardware,
fall back to a randomly generated one.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to save power, let's disable the regulator in the suspend function and
enable it in resume.
Tested on a mx28evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During probe the clocks are enabled prior than the acquiring the interrupts.
In the remove function we need to do the opposite: first remove the interrupts
and then disable the clocks.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of error during probe, disable the PHY regulator.
Do the same in fec_drv_remove().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when fec_enet_init fails it jumps to 'failed_init' error path, which
will attemp to free the interrupts.
This is wrong because at this point the interrupts have not even been acquired.
Swap failed_init/failed_irq to fix the error path.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a local reg_phy structure, let's put it inside the private
structure, so that we are able to have access to the regulator structure even
when we are outside fec_probe().
This is in preparation for controlling the FEC PHY regulator in the suspend and
resume functions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge net into net-next because some upcoming net-next changes
build on top of bug fixes that went into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the standard DIV_ROUND_UP macro in order to provide better readability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MVF is a family while MVF600 is a particular SoC in the family. We
generally prefer to use SoC rather than family name in compatible string
to define a particular type of fec device. And this is how fec_dt_ids
works for all those IMX fec variants. Let's change mvf to mvf600 to
have it work in the same way.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core)
we can rely on device core for handling pinctrl, so remove
devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing iounmap() before return from gianfar_ptp_probe()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 54309fa6 ("net: fec: fix kernel oops when plug/unplug cable many times")
introduced the following 'if' block in the beginning of fec_start():
if (netif_running(ndev)) {
netif_device_detach(ndev);
napi_disable(&fep->napi);
netif_stop_queue(ndev);
netif_tx_lock_bh(ndev);
}
Then later in the end of fec_restart() there is another block that calls the
opposite of each one of these functions.
The correct approach would be to also call them with in the reverse order, so
that we have as result:
if (netif_running(ndev)) {
netif_tx_unlock_bh(ndev);
netif_wake_queue(ndev);
napi_enable(&fep->napi);
netif_device_attach(ndev);
}
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4c09eed (net: fec: Enable imx6 enet checksum acceleration.)
enables hardware checksum acceleration unconditionally for all fec
variants. This is inappropriate, because some variants like imx5 have
no such support on hardware. Consequently, fec is broken on these
platforms. Fix it by enabling hardware checksum only on imx6q-fec type
of controllers.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
reproduce steps
1. flood ping from other machine
ping -f -s 41000 IP
2. run below script
while [ 1 ]; do ethtool -s eth0 autoneg off;
sleep 3;ethtool -s eth0 autoneg on; sleep 4; done;
You can see oops in one hour.
The reason is fec_restart clear BD but NAPI may use it.
The solution is disable NAPI and stop xmit when reset BD.
disable NAPI may sleep, so fec_restart can't be call in
atomic context.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
This is support for the ARM Chromebook, originally scheduled
as a "late" pull request. Since it's already late now, we
can combine this into the existing next/dt2 branch.
* late/dt:
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/net/ethernet/emulex/benet/be.h
include/net/tcp.h
net/mac802154/mac802154.h
Most conflicts were minor overlapping stuff.
The be2net driver brought in some fixes that added __vlan_put_tag
calls, which in net-next take an additional argument.
Signed-off-by: David S. Miller <davem@davemloft.net>
Enables hardware generation of IP header and
protocol specific checksums for transmitted
packets.
Enabled hardware discarding of received packets with
invalid IP header or protocol specific checksums.
The feature is enabled by default but can be
enabled/disabled by ethtool.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An early draft of the PHC patch series included an alarm in the
gianfar driver. During the review process, the alarm code was dropped,
but the capability removal was overlooked. This patch fixes the issue
by advertising zero alarms.
This patch should be applied to every 3.x stable kernel.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Chris LaRocque <clarocq@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
