Commit Graph

5815 Commits

Author SHA1 Message Date
Márton Németh
265a8098e7 V4L/DVB (13385): gspca - pac7302: Add red and blue balance control.
The valid values for these controls are 0..3 (lower two bits) which was
identified by trial and error on Labtec Webcam 2200 (USB ID 093a:2626).
The upper 6 bits are ignored on page 0, registers 0xc5 and 0xc7 by the camera.

Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:38 -02:00
Jean-Francois Moine
d5aa3856fd V4L/DVB (13384): gspca - sonixj: Optimize code and add some comments.
- the i2c base address is now taken from the sn9c1xx register table

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:37 -02:00
Márton Németh
b1784b3377 V4L/DVB (13383): gspca - pac7311/pac7302: Propagate error to higher level software.
The usb_control_msg() can fail any time. Only continue writing
sequence if there was no error with the previous write. If there
was any problem stop sending URBs and propagate the error to the
gspca_main.

Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:37 -02:00
Márton Németh
67c98f72e1 V4L/DVB (13382): gspca - pac7302: Remove redundant stream off command.
The stream off command is sent to the device twice, one is enough.

Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:37 -02:00
Alexander Strakh
2b588db82d V4L/DVB (13379): quickcam_messenger: possible buffer overflow while use strncat
In driver ./drivers/media/video/usbvideo/quickcam_messenger.c in line 91:

  91         usb_make_path(dev, cam->input_physname, sizeof(cam->input_physname));

After this line we use strncat:

  92         strncat(cam->input_physname, "/input0", sizeof(cam->input_physname));

where sizeof(cam->input_physname) returns length of cam->input_phisname
without length for null-symbol.  But this parameter must be - "maximum
numbers of bytes to copy", i.e.:
sizeof(cam->input_physname)-strlen(cam->input_physname)-1.

In this case, after call to usb_make_path the similar drivers use strlcat.

Like in: drivers/hid/usbhid/hid-core.c:
1152         usb_make_path(dev, hid->phys, sizeof(hid->phys));
1153         strlcat(hid->phys, "/input", sizeof(hid->phys));

Found by Linux Driver Verification Project.

Use strlcat instead of strncat.

Signed-off-by: Alexander Strakh <strakh@ispras.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:36 -02:00
Alexander Strakh
caac970f91 V4L/DVB (13378): konicawc.c: possible buffer overflow while use strncat
In driver ./drivers/media/video/usbvideo/konicawc.c in line 227:

227         usb_make_path(dev, cam->input_physname, sizeof(cam->input_physname));

After this line we use strncat:

228         strncat(cam->input_physname, "/input0", sizeof(cam->input_physname));

where sizeof(cam->input_physname) returns length of cam->input_phisname
without length for null-symbol.  But this parameter must be - "maximum
numbers of bytes to copy", i.e.:
sizeof(cam->input_physname)-strlen(cam->input_physname)-1.

In this case, after call to usb_make_path the similar drivers use strlcat.

Like in drivers/hid/usbhid/hid-core.c:
1152         usb_make_path(dev, hid->phys, sizeof(hid->phys));
1153         strlcat(hid->phys, "/input", sizeof(hid->phys));

Found by Linux Driver Verification Project.

Use strlcat instead of strncat.

Signed-off-by: Alexander Strakh <strakh@ispras.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:35 -02:00
Jonathan Corbet
38a54f35a0 V4L/DVB (13377): make struct videobuf_queue_ops constant
The videobuf_queue_ops function vector is not declared constant, but
there's no need for the videobuf layer to ever change it.  Make it const
so that videobuf users can make their operations const without warnings.

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:35 -02:00
David T. L. Wong
ea5697fe9e V4L/DVB (13375): cx23885: Add support for Mygica X8558Pro DMB-TH
Adds support for cx23885 card Mygica X8558 Pro DMB-TH

Signed-off-by: David T. L. Wong <davidtlwong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:34 -02:00
Michael Krufky
7fec6fee56 V4L/DVB (13349): cx23885: Enable IR input keypress handling for the Hauppauge WinTV HVR-1290
The IR on the HVR-1290 is identical to that of the HVR-1850

Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:27 -02:00
Michael Krufky
73a5f4196d V4L/DVB (13348): cx23885: update model matrix for models 85021 and 85721
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:27 -02:00
Michael Krufky
aee0b24c05 V4L/DVB (13347): cx23885: add digital television support for Hauppauge WinTV-HVR1290
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:27 -02:00
Igor M. Liplianin
29372a8dae V4L/DVB (13336): stv0900: config definition for single/dual mode
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:24 -02:00
Abylay Ospan
9329fb5b73 V4L/DVB (13335): stv0900: fix diseqc support for NetUP card
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:24 -02:00
Abylay Ospan
873688cd30 V4L/DVB (13334): stv6110: add configurable gain
It has positive effect for NetUP Dual DVB-S2 CI card.

Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:23 -02:00
Devin Heitmueller
48c511ed67 V4L/DVB (13331): mxl5005s: provide ability to override QAM gain for HVR-1600
The HVR-1600 doesn't use the standard mechanism for computing the gain when
in QAM mode, instead always forcing it to be 0x02.  Provide the ability to
override the algorithm on a per-board basis.

This change results in an improvement of 0.4-0.6 dB for QAM tuning.

This work was sponsored by ONELAN Limited.

Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:23 -02:00
Devin Heitmueller
af5c8e1523 V4L/DVB (13329): s5h1409: provide HVR-1600 specific optimizations
Perform some optimization of the register configuration based on a trace
of the HVR-1600 Windows i2c traffic (and consultation with Steven Toth).
Note that some of these values may be able to be moved into the common driver,
but I am holding off on that until they can be tested with other boards.

This work was sponsored by ONELAN Limited.

Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:22 -02:00
Mauro Carvalho Chehab
f57b17c395 V4L/DVB (13328): em28xx: Add chip ID for em2800
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:21 -02:00
Mauro Carvalho Chehab
fc099f0e0e V4L/DVB (13327): em28xx: fix alt modprobe parameter
It seems that some patch broke alt modprobe parameter. Fix it to allow
changing alternate interfaces during module load and at runtime.

If changed during runtime, you'll need to stop a and restart stream for
the parameter to be used.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:21 -02:00
Marton Nemeth
8337fc3053 V4L/DVB (13325): gspca - pac7302/pac7311: Fix buffer overrun.
The reg_w_seq() function expects the sequence length in entries
and not in bytes. One entry in init_7302 and init_7311 is two
bytes and not one.

Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:21 -02:00
Marton Nemeth
4f7309e278 V4L/DVB (13324): gspca - pac7302/pac7311: Handle return value of usb_control_msg().
The function usb_control_msg() can return error any time so at least
warn the user if an error happens. No message is printed in case of
normal operation.

Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:20 -02:00
Jean-Francois Moine
56205cc0dd V4L/DVB (13323): gspca - zc3xx: Adjust the exchanges of sensors mi0360soc and pb0330.
- the pb03303x exchanges were the mi0360soc ones
- add the new sensor mi0360soc
- the new exchanges are taken from the info file of the ms-win driver
  of the webcams 0ac8:301b and 0ac8:303b (vm30x.inf)

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:20 -02:00
Laurent Pinchart
350d6407f8 V4L/DVB (13310): uvcvideo: Return -EINVAL instead of -ENODEV in read()
-EINVAL is required by the V4L2 specification. -ENODEV is simply wrong
as the device exists.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:19 -02:00
Laurent Pinchart
3bc766ad37 V4L/DVB (13308): uvcvideo: Add support for MSI StarCam 370i webcams
The MSI StarCam 370i (1b3b:2951) requires the MINMAX quirk. Add a
corresponding entry in the device IDs list.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:19 -02:00
Jean-Francois Moine
5b34e3e4eb V4L/DVB (13306): gspca - sonixj: Change the copyright.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:19 -02:00
Jean-Francois Moine
0939e26669 V4L/DVB (13305): gspca - sonixj: The V flip control does not exist for all sensors.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:18 -02:00
Jean-Francois Moine
98941e4dad V4L/DVB (13304): gspca - sonixj: Don't access the sensor when setting the bridge.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:18 -02:00
Jean-Francois Moine
3fccb774ef V4L/DVB (13303): gspca - sonixj: Change sensor and om6802 exchanges.
- the sensors are now initialized sooner
- om6802:
  . set some parameters in factory mode
  . lack of some parameters
  . gpio adjustments

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:17 -02:00
Jean-Francois Moine
a782636c26 V4L/DVB (13302): gspca - sonixj: Fix some bad values of sensor om6802.
- sensor address is 0x34
- sensor i2c is 100 kHz

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:17 -02:00
Jean-Francois Moine
23a98274cc V4L/DVB (13301): gspca - sonixj: Simplify the sensor init exchanges.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:16 -02:00
Marton Nemeth
1408b84729 V4L/DVB (13300): gspca - pac7302/pac7311: Separate the two subdrivers.
All PAC7311 specific functions remain in pac7311.c. All PAC7302 specific
functions are moved to pac7302.c. The USB device table is also divided into
two parts. This makes it possible to remove the sensor specific decisions
from different functions and also remove sensor infromation from the USB
device table.

The common functions are just copied to both subdrivers. These common
functions can be separated later to a common file or helper module.

Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:16 -02:00
Marton Nemeth
cc409c0efb V4L/DVB (13299): gspca - pac7311: Extract pac_start_frame.
Creating the start of the frame is done in the same way for pac7302
and for pac7311. Extract this common part to the pac_start_frame()
function.

Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:16 -02:00
Marton Nemeth
a6b69e409a V4L/DVB (13298): gspca - pac207/pac7311/mr97310a: Simplify pac_find_sof.
Remove struct sd dependency from pac_find_sof() function implementation.
This step prepares separation of pac7302 and pac7311 specific parts of
struct sd.

Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:15 -02:00
Sebastian Andrzej Siewior
6f901a9919 V4L/DVB (13292): tvp514x: recognize the error case in tvp514x_read_reg()
i2c_smbus_read_byte_data() returns a negative value on error. It is very
likely to be != -1 (-EPERM).

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:13 -02:00
Filipe Rosset
480be1851a V4L/DVB (13290): em28xx-dvb: Convert printks to em28xx_err and em28xx_info
Convert printks to em28xx_err and em28xx_info

Signed-off-by: Filipe Rosset <rosset.filipe@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:13 -02:00
Filipe Rosset
0bc23083cf V4L/DVB (13289): em28xx-audio: Convert printks to em28xx_err
Convert printks to em28xx_err.

Signed-off-by: Filipe Rosset <rosset.filipe@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:13 -02:00
Peter Huewe
9710e7a77a V4L/DVB (13288): adding __init/__exit macros to various drivers
Trivial patch which adds the __init/__exit macros to the module_init/
module_exit functions of the following drivers in media video:
    drivers/media/video/ivtv/ivtv-driver.c
    drivers/media/video/cx18/cx18-driver.c
    drivers/media/video/davinci/dm355_ccdc.c
    drivers/media/video/davinci/dm644x_ccdc.c
    drivers/media/video/saa7164/saa7164-core.c
    drivers/media/video/saa7134/saa7134-core.c
    drivers/media/video/cx23885/cx23885-core.c

Cc: Hermann Pitton <hermann-pitton@arcor.de>
Acked-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Andy Walls <awalls@radix.net>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:12 -02:00
Roel Kluin
0b66cf9037 V4L/DVB (13285): vpfe_capture: keep index within bound in vpfe_cropcap()
If vpfe_dev->std_index equals ARRAY_SIZE(vpfe_standards), that is
one too large.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:12 -02:00
Michael Krufky
117e1348f8 V4L/DVB (13269): saa7134: codingstyle: use /* style comments */ instead of //
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:11 -02:00
Theodore Kilgore
542821d8d0 V4L/DVB (13267): gspca_mr97310a: Change brightness for VGA type 1 cameras downward
gspca_mr97310a: Change brightness for VGA type 1 cameras downward

Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:10 -02:00
Theodore Kilgore
b4b84deede V4L/DVB (13266): gspca_mr97310a: Fix / update some comments
gspca_mr97310a: Fix / update some comments

Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:10 -02:00
Theodore Kilgore
b31210d737 V4L/DVB (13265): gspca_mr97310a: Partly back off red gain change for Sakar Digital VGA camera
gspca_mr97310a: Partly back off red gain change for Sakar Digital VGA camera

Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:09 -02:00
Michael Obst
0700adec9e V4L/DVB (13260): saa7134: add support for Leadtek Winfast DTV-1000S remote control
Signed-off-by: Michael Obst <mike.obst@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:08 -02:00
Michael Krufky
53c8ec5e0e V4L/DVB (13259): saa7134: fix badly merged DTV1000S patch
As pointed out by Hermann Pitton, it turns out that the DTV1000S card's
analog entry made it into the #if 0 flyvideo tweaks in saa7134-cards.c
and is not valid there.

This patch fixes the problem.

Cc: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:08 -02:00
Andy Walls
928213aad7 V4L/DVB (13253): cx23885: CodingStyle fix
Add whitespace around binary operators in cx23888-ir.c

Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:08 -02:00
Jean-Francois Moine
7fb101ae25 V4L/DVB (13251): gspca - sonixj: Cleanup code and change some comments.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:07 -02:00
Jean-Francois Moine
721ecbcbea V4L/DVB (13250): gspca - zc3xx: Add some delays and warn on i2c errors.
This patch fixes the kernel bug 14195 (random errors - bad images -
with the webcam 10fd:8050 - sensor tas5130cxx).

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:07 -02:00
Jean-Francois Moine
56e93ed9cf V4L/DVB (13249): gspca - pac7311: Webcam 093a:2628 added.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:06 -02:00
Michael Krufky
d6eef49478 V4L/DVB (13247): tuner-core: dont force every tuner to set frequency at startup
Setting the tuner frequency at the same time as initializing the other devices
on the i2c bus can cause problems on devices that require firmware download or
extensive calibration proceduces during initialization.

This change allows us to prevent the tune at startup for devices that perform
better without it.

Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:06 -02:00
Theodore Kilgore
64f4d9a367 V4L/DVB (13245): gspca_mr97310a: Change blue gain setting for Sakar Digital VGA camera
gspca_mr97310a: Change blue gain setting for Sakar Digital VGA camera

Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:06 -02:00
Theodore Kilgore
1160a3818e V4L/DVB (13244): gspca_mr97310a: Fix / update some comments
gspca_mr97310a: Fix / update some comments

Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-12-05 18:41:05 -02:00