When the i2400m is connected to a network, the host interface (USB)
cannot be suspended. For that to happen, the device has to have
negotiated with the basestation to put the link on IDLE state.
If the host tries to put the device in standby while it is connected
but not idle, the device resets, as the driver should not do that.
To avoid triggering that, when the USB susbsytem requires the driver
to autosuspend the device, the driver checks if the device is not yet
idle. If it is not, the request is requested (will be retried again
later on after the autosuspend timeout). At some point the device will
enter idle and the request will succeed (unless of course, there is
network traffic, but at that point, there is no idle neither in the
link or the host interface).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
From a fix by Cindy H Kao:
Block size has to be set before sending IOE enable because the
firmware reads the block size register before it reads IOE register.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Functions i2400m_report_tlv*() are only called from
i2400m_report_hook(), called in a workqueue by
i2400m_report_hook_work(). The scheduler checks for device readiness
before scheduling.
Added an extra check for readiness in i2400m_report_hook_work(), which
makes all the checks down the line redundant.
Obviously the device state could change in the middle, but error
handling would take care of that.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
By running 'echo 1 > /sys/kernel/debug/wimax:wmxX/i2400m/trace_msg_from_user',
the driver will echo to user space all the commands being sent to the
device from user space, along with the responses.
However, this only helps with the commands being sent from user space;
with this patch, the trace hook is moved to i2400m_msg_to_dev(), which
is the single access point for running commands to the device (both by
user space and the kernel driver). This allows better debugging by
having a complete stream of commands/acks and reports.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
When commands are sent from user space, trace both the command sent
and the answer received over the "echo" pipe instead of over the
"trace" pipe when command tracing is enabled. As well, when the device
sends a reports/indications, send it over the "echo" pipe.
The "trace" pipe is used by the device to send firmware traces;
gets confusing. Another named pipe makes it easier to split debug
information.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The WiMAX i2400m driver needs to generate a fake source MAC address to
fake an ethernet header (for destination, the card's MAC is
used). This is the source of the packet, which is the basestation it
came from. The basestation's mac address is not usable for this, as it
uses its own namespace and it is not always available.
Currently the fake source MAC address was being set to all zeros,
which was causing trouble with bridging.
Use random_ether_addr() to generate a proper one that creates no
trouble.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The current driver tries to re-register the DCA requester after reset and
this is not correct. This change makes it so all we are doing is resetting
the DCA registers after reset and not re-adding the requester.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver is re-registering the DCA requester after every reset.
Instead of doing this we should only be updating the on board DCA registers
and not unregistering/re-registering our requester.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio's dev field needs to be set before mdio ops occur.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio's dev field needs to be set before mdio ops occur.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO/LRO can be controlled through ethtool so this is unnecessary.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow myri10ge LRO to be enabled/disabled via ethtool
(and by the stack for packet forwarding).
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is purely a cleanup patch. This collapses some of the code required
when we configure our Tx and Rx feature sets, and makes the code more
readable and maintainable.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFF specification for Direct Attach cable detection has now been
ratified. Previously, DA cable detect was looking at the Twinaxial bit in
byte 9 of the SFP+ EEPROM. The spec now defines active and passive DA
cables in byte 8 of the SFP+ EEPROM. This patch changes the cable
detection for both 82598 and 82599 SFP+ adapters to conform to the new
spec.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFP+ NIC (device id 0x10fb) needs a semaphore to serialize
PHY access, so our PHY init code must honor that same semaphore.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to mostly historic reasons, including a lack of reliability
of the link handling (especially with the older 8169), the
current r8169 driver emulates forced mode setting by limiting
the advertised modes.
With this change the driver allows real 10/100 forced mode
settings on the 8169 and 8101/8102.
Original idea by Vincent Steenhoute. The RTL_GIGA_MAC_VER_03
tweak was extracted from Realtek's r8169 v6.010.00 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek pointed pppoe can call back dev_queue_xmit(), and might need
skb->dst, so its safer to unset IFF_XMIT_DST_RELEASE on ppp devices.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One point of contention in high network loads is the dst_release() performed
when a transmited skb is freed. This is because NIC tx completion calls
dev_kree_skb() long after original call to dev_queue_xmit(skb).
CPU cache is cold and the atomic op in dst_release() stalls. On SMP, this is
quite visible if one CPU is 100% handling softirqs for a network device,
since dst_clone() is done by other cpus, involving cache line ping pongs.
It seems right place to release dst is in dev_hard_start_xmit(), for most
devices but ones that are virtual, and some exceptions.
David Miller suggested to define a new device flag, set in alloc_netdev_mq()
(so that most devices set it at init time), and carefuly unset in devices
which dont want a NULL skb->dst in their ndo_start_xmit().
List of devices that must clear this flag is :
- loopback device, because it calls netif_rx() and quoting Patrick :
"ip_route_input() doesn't accept loopback addresses, so loopback packets
already need to have a dst_entry attached."
- appletalk/ipddp.c : needs skb->dst in its xmit function
- And all devices that call again dev_queue_xmit() from their xmit function
(as some classifiers need skb->dst) : bonding, vlan, macvlan, eql, ifb, hdlc_fr
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sysfs files for a network device can not unconditionally take the
rtnl_lock as the bonding sysfs files do. If someone accesses those
sysfs files while the network device is being unregistered with the
rtnl_lock held we will deadlock.
So use trylock and restart_syscall to avoid this problem.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pdev->irq was not saved in netxen_adapter, causing request_irq()
with invalid irq number.
This was broken in commit be339aee63
("netxen: fix irq tear down and msix leak.").
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Per Dalen <per.dalen@cnw.se>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds support for the one or two channel CPC-PCI and CPC-PCIe
cards from EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de).
Signed-off-by: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: Markus Plessing <plessing@ems-wuensche.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver adds support for the SJA1000 chips connected to the
"platform bus", which can be found on various embedded systems.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the generic Socket-CAN driver for the Philips SJA1000
full CAN controller.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CAN network device driver interface provides a generic interface to
setup, configure and monitor CAN network devices. It exports a set of
common data structures and functions, which all real CAN network device
drivers should use. Please have a look to the SJA1000 or MSCAN driver
to understand how to use them. The name of the module is can-dev.ko.
Furthermore, it adds a Netlink interface allowing to configure the CAN
device using the program "ip" from the iproute2 utility suite.
For further information please check "Documentation/networking/can.txt"
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for TI DaVinci EMAC driver.
TI DaVinci Ethernet Media Access Controller module is based upon
TI CPPI 3.0 DMA engine and supports 10/100 Mbps on all and Gigabit modes on
some TI devices. It supports MII/RMII and has up to 8Kbytes of internal
descriptor memory. This driver has been working on several TI devices including
DM644x, DM646x and DA830 platforms. The specs of this device are available at:
http://www.ti.com/litv/pdf/sprue24a
Signed-off-by: Anant Gole <anantgole@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marching along, let's bump the version number to indicate things actually
have happened to the driver.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the generic XAUI device support for 82599 controllers.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The performance of hardware RSC is greatly reduced if the total for max rsc
descriptors multiplied by the buffer size is greater than 65535. To
prevent this we need to adjust the max rsc descriptors appropriately.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FIFO1_DMA_ERR is set twice, the second should be FIFO2_DMA_ERR.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Ram Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After 2.6.29, PPC no more admits passing NULL to the dev parameter of
the DMA API. The result is a BUG followed by solid lock-up when the
mv643xx_eth driver brings an interface up. The following patch makes
the driver work on my Pegasos again; it is mostly a search and replace
of NULL by mp->dev->dev.parent in dma allocation/freeing/mapping/unmapping
functions.
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the purposes of bonding is to allow for redundant links, and failover
correctly if the cable is pulled. If all the members of a bonded device have
no carrier present, the bonded device itself needs to report no carrier present
to user space so management tools (like routing daemons) can respond.
Bonding in 802.3ad mode does not work correctly for this because it incorrectly
chooses a link that is down as a possible aggregator.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in DCB mode, switching between link flow control and priority
flow control shouldn't need to reset the hardware. This removes that
reset.
This also extends the set_all() dcbnl callback to return a value indicating
that the HW config changed, however a reset was not required.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool should report that link flow control is disabled when in priority
flow control mode.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 supports using either link flow control or priority flow control when
in DCB mode. The dcbnl interface already supports sending down
configurations through rtnetlink that can enable LFC when DCB is enabled,
so the driver should take advantage of this.
82598 does not support using LFC when DCB is enabled, so explicitly disable
it when we're in DCB mode. This means we always run in PFC mode when DCB
is enabled.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sets the low water threshhold for priority flow control for 82598
and 82599 controllers in DCB mode.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable jumbo frame when FCoE feature is enabled in 82599. Use 3K
as the receive queue buffer size for receive queues used by FCoE
to address for max Fiber Channel frame size as 2148 bytes (with
max 2112 bytes of payload).
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable using FCoE redirection table feature in 82599. The FCoE
redirection table has maximum of eight entries, corresponding
to maximum of eight receive queues to be used for distributing
incoming FCoE packets. This patch sets up the FCoE redirection
table when multiple receive queues are available for FCoE.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ring feature for FCoE to make use of the FCoE redirection
table in 82599. The FCoE redirection table is a receive side
scaling feature for Fiber Channel over Ethernet feature in 82599,
enabling distributing FCoE packets to different receive queues
based on the exchange id.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After acquiring the SAN MAC address from the EEPROM, we need to program it
into one of the RARs. Also, DCB will use this MAC address to run DCBX
commands, so it doesn't have to play musical MAC addresses when things like
bonding enter the picture. So we need to return the MAC address through
the netlink interface to userspace.
This also moves the init_rx_addrs() call out of start_hw() and into
reset_hw(). We shouldn't try to read any of the RAR information before
initializing our internal accounting of the RAR table, which was what
was happening.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
