No reason to keep this u8, really.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It doesn't make sense to just copy the information to the PLL flags. Add a
new fields for the quirks to contain the PLL flags.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sub-device names should be unique. Should two identical sensors be
present in the same media device they would be indistinguishable. The names
will change e.g. from "vs6555 pixel array" to "vs6555 1-0010 pixel array".
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
8-bit reads are needed in some cases; however the condition used was wrong.
Regular access (register width) was used if:
len == SMIAPP_REG_8BIT && !only8
This causes 8-bit read access to be used always. The operator should be ||
instead: regular access can be used for 8-bit reads OR if allowed otherwise.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
SMIAPP_REG_ is the common prefix used in the driver for register related
definitions. Use it consistently.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The quirk registers mechanism which allows register to have a static read
access value from the sensor specific quirks, is not used. Remove it. It is
to be replaced by a more generic register diversion quirk soon.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In core_init make sure access to EDID DDC lines are disabled
before chip is powered up. Also DISABLE_AUTO_EDID before power up.
The correct setting is applied later when setting the EDID.
Some sources (MAC) kept on reading EDID even when Hotplug was low
and in the short period in core_init before the DDC lines was enabled
read a corrupt EDID.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This was the reason for enabling the HDMI/DVI-D mode irq in the first place.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This fixes following build error:
CC drivers/media/i2c/s5c73m3/s5c73m3-core.o
CC drivers/md/dm-ioctl.o
CC net/ipv4/inet_lro.o
drivers/media/i2c/s5c73m3/s5c73m3-core.c: In function ‘s5c73m3_get_platform_data’:
drivers/media/i2c/s5c73m3/s5c73m3-core.c:1619:2: error: implicit declaration of function ‘v4l2_of_get_next_endpoint’ [-Werror=implicit-function-declaration]
drivers/media/i2c/s5c73m3/s5c73m3-core.c:1619:10: warning: assignment makes pointer from integer without a cast [enabled by default]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull exynos media updates from Mauro Carvalho Chehab:
"These are the remaining patches I have for the merge windows. It
basically adds a new sensor and adds the needed DT bits for it to
work"
* 'topic/exynos' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] s5p-fimc: Remove reference to outdated macro
[media] s5p-jpeg: Fix broken indentation in jpeg-regs.h
[media] exynos4-is: Add the FIMC-IS ISP capture DMA driver
[media] exynos4-is: Add support for asynchronous subdevices registration
[media] exynos4-is: Add clock provider for the SCLK_CAM clock outputs
[media] exynos4-is: Use external s5k6a3 sensor driver
[media] V4L: s5c73m3: Add device tree support
[media] V4L: Add driver for s5k6a3 image sensor
[media] Documentation: devicetree: Update Samsung FIMC DT binding
[media] Documentation: dt: Add binding documentation for S5C73M3 camera
[media] Documentation: dt: Add binding documentation for S5K6A3 image sensor
Pull media updates from Mauro Carvalho Chehab:
"The main set of series of patches for media subsystem, including:
- document RC sysfs class
- added an API to setup scancode to allow waking up systems using the
Remote Controller
- add API for SDR devices. Drivers are still on staging
- some API improvements for getting EDID data from media
inputs/outputs
- new DVB frontend driver for drx-j (ATSC)
- one driver (it913x/it9137) got removed, in favor of an improvement
on another driver (af9035)
- added a skeleton V4L2 PCI driver at documentation
- added a dual flash driver (lm3646)
- added a new IR driver (img-ir)
- added an IR scancode decoder for the Sharp protocol
- some improvements at the usbtv driver, to allow its core to be
reused.
- added a new SDR driver (rtl2832u_sdr)
- added a new tuner driver (msi001)
- several improvements at em28xx driver to fix PM support, device
removal and to split the V4L2 specific bits into a separate
sub-driver
- one driver got converted to videobuf2 (s2255drv)
- the e4000 tuner driver now follows an improved binding model
- some fixes at V4L2 compat32 code
- several fixes and enhancements at videobuf2 code
- some cleanups at V4L2 API documentation
- usual driver enhancements, new board additions and misc fixups"
[ NOTE! This merge effective drops commit 4329b93b28 ("of: Reduce
indentation in of_graph_get_next_endpoint").
The of_graph_get_next_endpoint() function was moved and renamed by
commit fd9fdb78a9 ("[media] of: move graph helpers from
drivers/media/v4l2-core to drivers/of"). It was originally called
v4l2_of_get_next_endpoint() and lived in the file
drivers/media/v4l2-core/v4l2-of.c.
In that original location, it was then fixed to support empty port
nodes by commit b9db140c1e ("[media] v4l: of: Support empty port
nodes"), and that commit clashes badly with the dropped "Reduce
intendation" commit. I had to choose one or the other, and decided
that the "Support empty port nodes" commit was more important ]
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (426 commits)
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
Revert "[media] em28xx-dvb: fix PCTV 461e tuner I2C binding"
[media] em28xx: fix PCTV 290e LNA oops
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
[media] m88ds3103: fix bug on .set_tone()
[media] saa7134: fix WARN_ON during resume
[media] v4l2-dv-timings: add module name, description, license
[media] videodev2.h: add parenthesis around macro arguments
[media] saa6752hs: depends on CRC32
[media] si4713: fix Kconfig dependencies
[media] Sensoray 2255 uses videobuf2
[media] adv7180: free an interrupt on failure paths in init_device()
[media] e4000: make VIDEO_V4L2 dependency optional
[media] af9033: Don't export functions for the hardware filter
[media] af9035: use af9033 PID filters
[media] af9033: implement PID filter
[media] rtl2832_sdr: do not use dynamic stack allocation
[media] e4000: fix 32-bit build error
[media] em28xx-audio: make sure audio is unmuted on open()
[media] DocBook media: v4l2_format_sdr was renamed to v4l2_sdr_format
...
There is request_irq() in init_device(), but the interrupt is not removed
on failure paths. The patch adds proper error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the V4L2 asynchronous subdev registration and
device tree support. Common clock API is used to control the
sensor master clock from within the subdev.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds subdev driver for Samsung S5K6A3 raw image sensor.
As it is intended at the moment to be used only with the Exynos
FIMC-IS (camera ISP) subsystem it is pretty minimal subdev driver.
It doesn't do any I2C communication since the sensor is controlled
by the ISP and its own firmware.
This driver, if needed, can be updated in future into a regular
subdev driver where the main CPU communicates with the sensor
directly.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The allowed and enabled protocol masks need to be expanded to be per
filter type in order to support wakeup filter protocol selection. To
ease that process abstract access to the rc_dev::allowed_protos and
rc_dev::enabled_protocols members with inline functions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These chips makes use of the media_entity in the v4l2_subdev struct
and is therefor dependent of the MEDIA_CONTROLLER config.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The adv7180 has a low power mode in which the analog and the digital processing
section are shut down. Implement the s_power callback to let bridge drivers put
the part into low power mode when not needed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for async device registration to the adv7180 driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The proper way to handle IRQs that need to be able to sleep in their IRQ handler
is to use a threaded IRQ.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The device driver core already prints out a very similar message when a driver
fails to probe. No need to print one in the driver itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The device can't possibly be registered at this point, so no need to to call
v4l2_device_unregister_subdev().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Make sure to free the control handler when the device is removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The mutex is used in the subdev callbacks, so unregister the subdev before the
mutex is destroyed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the driver for the LM3646, dual LED Flash driver.
The LM3646 has two 1.5A sync. boost converter with dual white current source.
It is controlled via an I2C compatible interface.
Each flash brightness, torch brightness and enable/disable can be controlled.
Under voltage, input voltage monitor and thermal threshhold Faults are added.
Please refer the datasheet http://www.ti.com/lit/ds/snvs962/snvs962.pdf
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If we have no pdata defined and driver fails to register we leak memory.
Converting to devm_kzalloc prevents this to happen.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Let's keep the style for all comments in the code, namely using small letters
whenever it's possible.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is no need to keep the FSF address inside each file. Moreover, it might
change in future which will make this one obsolete.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Set permissions on the debug module parameter to make it appear in sysfs.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch moves the parsing helpers used to parse connected graphs
in the device tree, like the video interface bindings documented in
Documentation/devicetree/bindings/media/video-interfaces.txt, from
drivers/media/v4l2-core/v4l2-of.c into drivers/of/base.c.
This allows to reuse the same parser code from outside the V4L2
framework, most importantly from display drivers.
The functions v4l2_of_get_next_endpoint, v4l2_of_get_remote_port,
and v4l2_of_get_remote_port_parent are moved. They are renamed to
of_graph_get_next_endpoint, of_graph_get_remote_port, and
of_graph_get_remote_port_parent, respectively.
Since there are not that many current users yet, switch all of
them to the new functions right away.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Closer inspection on exact transmitted format showed that
we needed to add 1 on vertical sync.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
HS_IN/VS_IN was always set to positive.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently only RGB444 input data is supported so set to zero.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the input clock frequency is out of bounds for the PLL, bypass the
PLL and just divide the input clock to achieve the requested output
frequency.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor needs a master clock, handle it explictly in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor needs two power supplies, VAA and VDD. Require a regulator
for each of them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several left overs with my old email address.
Remove their occurrences and add myself at CREDITS, to
allow people to be able to reach me on my new addresses.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This applies to HDMI-map register 0x69.
So far we have been using HPA manual mode.
This way we had control of HPA which could be
set after EDID had been programmed.
Using a Mac Mini with mini-displayport to DVI-D converter as source
caused the adv7842 to lock up and fail to detect any further signals.
After experimenting with different configurations it was found that
using the HPA auto mode and in addition letting RX-termination
be controlled by HPA prevented this error from occuring.
I was not able to re-create this problem on the adv7604.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Clear any pending AVI checksum-errors.
To be able to display last received AVI.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Incorrect registers used for pixelclock read-out.
Same registers as for adv7604 which actually gave an almost
correct read-out, even they are not documented for adv7842.
Corrected deep-color pixel-clock correction.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the input signal is DVI-D and quantization range is RGB full range,
gain and offset must be adjusted to get the right range on the output.
Copied and adopted from adv7604.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Using variable length array in s5k5baf_write_arr_seq caused
an implicit assumption that i2c sequences should be short.
The patch rewrites the function so it can handle sequences
of any length and does not use variable length array.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes the following error:
ERROR: return is not a function, parentheses are not required
FILE: drivers/media/i2c/s5k5baf.c:1353:
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes the following warnings:
drivers/media/i2c/s5k5baf.c: In function 's5k5baf_fw_parse':
drivers/media/i2c/s5k5baf.c:362:3: warning:
format '%d' expects argument of type 'int', but argument 3 has type 'size_t' [-Wformat=]
drivers/media/i2c/s5k5baf.c:383:4: warning:
format '%d' expects argument of type 'int', but argument 4 has type 'size_t' [-Wformat=]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As discussed on the media summit 2013, there is no reason for the width
and height to be signed.
Therefore this patch is an attempt to convert those fields from __s32 to
__u32.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi> (documentation and smiapp)
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
saa6588 always blocked while waiting for data, even if the filehandle
was in non-blocking mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
CMD_CLOSE sets data_available_for_read to 1, which is necessary to do the
wakeup call, but it is never reset to 0.
Because of this calling CMD_POLL afterwards will always return that data is
available, even if there isn't any.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This driver is independent from saa7134, so there is no reason why this
shouldn't be in media/i2c like all other i2c media drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a proper driver strength enum and use the same names in the platform
data as with adv7604.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This timing must be supported by all HDMI equipment, so that's a
reasonable default.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The correct LLC DLL phase depends on the board layout, so this
should be part of the platform_data.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Tested-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Return 0 if the new timings are equal to the current timings as
it caused extra cp-loss/lock interrupts.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The free-run mode can be board-specific.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Must clear timings before setting after test to recover.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Clear i2c_clients ptr when unregistered.
Warn if configured i2c-addr is zero.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The STDI block may measure wrong values, especially for lcvs and lcf.
If the driver can not find any valid timing, the STDI block is restarted
to measure the video timings again. The function will return an error,
but the restart of STDI will generate a new STDI interrupt and the format
detection process will restart.
Copied from adv7604.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Wait 5ms after main reset. The data-sheet doesn't specify the wait
after i2c-controlled reset, so using same value as after pin-controlled
reset.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Both the PAL and NTSC standards are interlaced where a
frame consist of two fields. Total number of lines in a frame in both systems
are an odd number so the two fields will have different length.
In the 625 line standard ("PAL") the odd field of the frame is transmitted first,
while in the 525 standard ("NTSC") the even field is transmitted first.
This adds the possibility to change output config between the fields and standards.
This setting will reduce the "format-jitter" on the signal sent by the pixelport
moving the difference between the fields to vertical front/back-porch only.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
For edid with no Source Physical Address (spa), set
spa-location to default and use correct values from edid.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added support for YCrCb analog input.
If input is ADV7842_MODE_RGB and RGB quantization range is set to
V4L2_DV_RGB_RANGE_AUTO, then video with CEA timings will be received
as RGB. For ADV7842_MODE_COMP, automatic CSC mode will be selected.
See table 48 on page 281 in "ADV7842 Hardware Manual, Rev. 0, January 2011"
for details.
Make sure that when switching inputs the RGB quantization range is
updated as well.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The method of disabling the irq-output pin caused many "empty"
interrupts. Instead, actually disable/enable the interrupts by
changing the interrupt masks.
Also enable STORE_MASKED_IRQ in INT1 configuration, otherwise when HDMI
events happen while the interrupt is masked those events will be ignored
when the interrupt is unmasked.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Bit 6 of register 0x8f was cleared incorrectly (must be 1), and bit 4
of register 0x91 was set incorrectly (must be 0).
These bits are undocumented, so we shouldn't modify them to values different
from what the datasheet specifies.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This simplified the code quite a bit.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This timing must be supported by all HDMI equipment, so that's a
reasonable default.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some sources are initially detected as DVI, and change to HDMI later.
This must be detected to set the right RGB quantization range.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the input signal is DVI-D and quantization range is RGB full range,
gain and offset must be adjusted to get the right range on the output.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the restart_stdi_once trick fails to find a valid
format the flag was never reset.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
ADV7604_FMT_CHANGE events was debounced in adv7604_isr() to avoid
that a receiver with a unstable input signal would block the event
handling for other inputs. This solution was prone to errors.
A better protection agains interrupt blocking is to delay the call
of the interrupt service routine in the adv7604 driver if too many
interrupts are received within a given time.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
- split edid_write_block()
- do not use edid->edid before the validity check
- Return -EINVAL if edid->pad is invalid
- Save both registers for SPA port A
- Set SPA location to default value if it is not found
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the input is ADV7604_INPUT_VGA_RGB and RGB quantization range is
set to V4L2_DV_RGB_RANGE_AUTO, video with CEA timings will be
received as RGB. For ADV7604_INPUT_VGA_COMP, automatic CSC mode
will be selected.
See table 44 on page 205 in "ADV7604 Hardware Manual, Rev. F, August 2010"
for details.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver strength is board dependent, so set it from the platform_data.
Signed-off-by: Mikhail Khelik <mkhelik@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
