ISA 3 allows for prevention of instruction fetch and execution
of user mode pages. If such an error occurs, SRR1 bit 35 reports the
error. We catch and report the error in do_page_fault().
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Setup AMOR (Authority Mask Override Register) in HV mode so that the
host and guest kernel can in turn setup IAMR.
This allows us to enable key 0 in a following patch.
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ensure that PSSCR is set to a safe value corresponding to no
state-loss each time a POWER9 CPU comes online.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-By: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is a nice interface for asking ftrace to dump all its tracing
buffers. The only down side for use in xmon is that it uses printk.
Depending on circumstances printk may not work when in xmon, but it also
may, so add a 'dt' command which dumps the ftrace buffers, and add a
note to the help to mentiont that it uses printk.
Calling this routine also disables tracing, which is problematic if you
return from xmon and expect the system to keep operating normally. So
after we do the dump turn tracing back on.
Both functions already have nop versions defined for when ftrace is not
enabled, so we don't need any extra #ifdefs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With commit e58e87adc8 ("powerpc/mm: Update _PAGE_KERNEL_RO") we
started using the ppp value 0b110 to map kernel readonly. But that
facility was only added as part of ISA 2.04. For earlier ISA version
only supported ppp bit value for readonly mapping is 0b011. (This
implies both user and kernel get mapped using the same ppp bit value for
readonly mapping.).
Update the code such that for earlier architecture version we use ppp
value 0b011 for readonly mapping. We don't differentiate between power5+
and power5 here and apply the new ppp bits only from power6 (ISA 2.05).
This keep the changes minimal.
This fixes issue with PS3 spu usage reported at
https://lkml.kernel.org/r/rep.1421449714.geoff@infradead.org
Fixes: e58e87adc8 ("powerpc/mm: Update _PAGE_KERNEL_RO")
Cc: stable@vger.kernel.org # v4.7+
Tested-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit d0563a1297 ("powerpc: Implement {cmp}xchg for u8 and u16")
we removed the volatile from __cmpxchg().
This is leading to warnings such as:
drivers/gpu/drm/drm_lock.c: In function ‘drm_lock_take’:
arch/powerpc/include/asm/cmpxchg.h:484:37: warning: passing argument 1
of ‘__cmpxchg’ discards ‘volatile’ qualifier from pointer target
(__typeof__(*(ptr))) __cmpxchg((ptr), (unsigned long)_o_, \
There doesn't seem to be consensus across architectures whether the
argument is volatile or not, so at least for now put the volatile back.
Fixes: d0563a1297 ("powerpc: Implement {cmp}xchg for u8 and u16")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When configured with CONFIG_PPC_EARLY_DEBUG_OPAL=y the kernel expects
the OPAL entry and base addresses to be passed in r8 and r9
respectively. Currently the wrapper does not attempt to restore these
values before entering the decompressed kernel which causes the kernel
to branch into whatever happens to be in r9 when doing a write to the
OPAL console in early boot.
This patch adds a platform_ops hook that can be used to branch into the
new kernel. The OPAL console driver patches this at runtime so that if
the console is used it will be restored just prior to entering the
kernel.
Fixes: 656ad58ef1 ("powerpc/boot: Add OPAL console to epapr wrappers")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At present KVM on powerpc always reports KVM_CAP_PPC_ALLOC_HTAB as enabled.
However, the ioctl() it advertises (KVM_PPC_ALLOCATE_HTAB) only actually
works on KVM HV. On KVM PR it will fail with ENOTTY.
QEMU already has a workaround for this, so it's not breaking things in
practice, but it would be better to advertise this correctly.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds the "again" parameter to the dummy version of
kvmppc_check_passthru(), so that it matches the real version.
This fixes compilation with CONFIG_BOOK3S_64_HV set but
CONFIG_KVM_XICS=n.
This includes asm/smp.h in book3s_hv_builtin.c to fix compilation
with CONFIG_SMP=n. The explicit inclusion is necessary to provide
definitions of hard_smp_processor_id() and get_hard_smp_processor_id()
in UP configs.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The function kvmppc_set_arch_compat() is used to determine the value of the
processor compatibility register (PCR) for a guest running in a given
compatibility mode. There is currently no support for v3.00 of the ISA.
Add support for v3.00 of the ISA which adds an ISA v2.07 compatilibity mode
to the PCR.
We also add a check to ensure the processor we are running on is capable of
emulating the chosen processor (for example a POWER7 cannot emulate a
POWER8, similarly with a POWER8 and a POWER9).
Based on work by: Paul Mackerras <paulus@ozlabs.org>
[paulus@ozlabs.org - moved dummy PCR_ARCH_300 definition here; set
guest_pcr_bit when arch_compat == 0, added comment.]
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
With POWER9, each CPU thread has its own MMU context and can be
in the host or a guest independently of the other threads; there is
still however a restriction that all threads must use the same type
of address translation, either radix tree or hashed page table (HPT).
Since we only support HPT guests on a HPT host at this point, we
can treat the threads as being independent, and avoid all of the
work of coordinating the CPU threads. To make this simpler, we
introduce a new threads_per_vcore() function that returns 1 on
POWER9 and threads_per_subcore on POWER7/8, and use that instead
of threads_per_subcore or threads_per_core in various places.
This also changes the value of the KVM_CAP_PPC_SMT capability on
POWER9 systems from 4 to 1, so that userspace will not try to
create VMs with multiple vcpus per vcore. (If userspace did create
a VM that thought it was in an SMT mode, the VM might try to use
the msgsndp instruction, which will not work as expected. In
future it may be possible to trap and emulate msgsndp in order to
allow VMs to think they are in an SMT mode, if only for the purpose
of allowing migration from POWER8 systems.)
With all this, we can now run guests on POWER9 as long as the host
is running with HPT translation. Since userspace currently has no
way to request radix tree translation for the guest, the guest has
no choice but to use HPT translation.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The new XIVE interrupt controller on POWER9 can direct external
interrupts to the hypervisor or the guest. The interrupts directed to
the hypervisor are controlled by an LPCR bit called LPCR_HVICE, and
come in as a "hypervisor virtualization interrupt". This sets the
LPCR bit so that hypervisor virtualization interrupts can occur while
we are in the guest. We then also need to cope with exiting the guest
because of a hypervisor virtualization interrupt.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
POWER9 replaces the various power-saving mode instructions on POWER8
(doze, nap, sleep and rvwinkle) with a single "stop" instruction, plus
a register, PSSCR, which controls the depth of the power-saving mode.
This replaces the use of the nap instruction when threads are idle
during guest execution with the stop instruction, and adds code to
set PSSCR to a value which will allow an SMT mode switch while the
thread is idle (given that the core as a whole won't be idle in these
cases).
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
POWER9 includes a new interrupt controller, called XIVE, which is
quite different from the XICS interrupt controller on POWER7 and
POWER8 machines. KVM-HV accesses the XICS directly in several places
in order to send and clear IPIs and handle interrupts from PCI
devices being passed through to the guest.
In order to make the transition to XIVE easier, OPAL firmware will
include an emulation of XICS on top of XIVE. Access to the emulated
XICS is via OPAL calls. The one complication is that the EOI
(end-of-interrupt) function can now return a value indicating that
another interrupt is pending; in this case, the XIVE will not signal
an interrupt in hardware to the CPU, and software is supposed to
acknowledge the new interrupt without waiting for another interrupt
to be delivered in hardware.
This adapts KVM-HV to use the OPAL calls on machines where there is
no XICS hardware. When there is no XICS, we look for a device-tree
node with "ibm,opal-intc" in its compatible property, which is how
OPAL indicates that it provides XICS emulation.
In order to handle the EOI return value, kvmppc_read_intr() has
become kvmppc_read_one_intr(), with a boolean variable passed by
reference which can be set by the EOI functions to indicate that
another interrupt is pending. The new kvmppc_read_intr() keeps
calling kvmppc_read_one_intr() until there are no more interrupts
to process. The return value from kvmppc_read_intr() is the
largest non-zero value of the returns from kvmppc_read_one_intr().
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
On POWER9, the msgsnd instruction is able to send interrupts to
other cores, as well as other threads on the local core. Since
msgsnd is generally simpler and faster than sending an IPI via the
XICS, we use msgsnd for all IPIs sent by KVM on POWER9.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
POWER9 adds new capabilities to the tlbie (TLB invalidate entry)
and tlbiel (local tlbie) instructions. Both instructions get a
set of new parameters (RIC, PRS and R) which appear as bits in the
instruction word. The tlbiel instruction now has a second register
operand, which contains a PID and/or LPID value if needed, and
should otherwise contain 0.
This adapts KVM-HV's usage of tlbie and tlbiel to work on POWER9
as well as older processors. Since we only handle HPT guests so
far, we need RIC=0 PRS=0 R=0, which ends up with the same instruction
word as on previous processors, so we don't need to conditionally
execute different instructions depending on the processor.
The local flush on first entry to a guest in book3s_hv_rmhandlers.S
is a loop which depends on the number of TLB sets. Rather than
using feature sections to set the number of iterations based on
which CPU we're on, we now work out this number at VM creation time
and store it in the kvm_arch struct. That will make it possible to
get the number from the device tree in future, which will help with
compatibility with future processors.
Since mmu_partition_table_set_entry() does a global flush of the
whole LPID, we don't need to do the TLB flush on first entry to the
guest on each processor. Therefore we don't set all bits in the
tlb_need_flush bitmap on VM startup on POWER9.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds code to handle two new guest-accessible special-purpose
registers on POWER9: TIDR (thread ID register) and PSSCR (processor
stop status and control register). They are context-switched
between host and guest, and the guest values can be read and set
via the one_reg interface.
The PSSCR contains some fields which are guest-accessible and some
which are only accessible in hypervisor mode. We only allow the
guest-accessible fields to be read or set by userspace.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Some special-purpose registers that were present and accessible
by guests on POWER8 no longer exist on POWER9, so this adds
feature sections to ensure that we don't try to context-switch
them when going into or out of a guest on POWER9. These are
all relatively obscure, rarely-used registers, but we had to
context-switch them on POWER8 to avoid creating a covert channel.
They are: SPMC1, SPMC2, MMCRS, CSIGR, TACR, TCSCR, and ACOP.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
On POWER9, the SDR1 register (hashed page table base address) is no
longer used, and instead the hardware reads the HPT base address
and size from the partition table. The partition table entry also
contains the bits that specify the page size for the VRMA mapping,
which were previously in the LPCR. The VPM0 bit of the LPCR is
now reserved; the processor now always uses the VRMA (virtual
real-mode area) mechanism for guest real-mode accesses in HPT mode,
and the RMO (real-mode offset) mechanism has been dropped.
When entering or exiting the guest, we now only have to set the
LPIDR (logical partition ID register), not the SDR1 register.
There is also no requirement now to transition via a reserved
LPID value.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adapts the KVM-HV hashed page table (HPT) code to read and write
HPT entries in the new format defined in Power ISA v3.00 on POWER9
machines. The new format moves the B (segment size) field from the
first doubleword to the second, and trims some bits from the AVA
(abbreviated virtual address) and ARPN (abbreviated real page number)
fields. As far as possible, the conversion is done when reading or
writing the HPT entries, and the rest of the code continues to use
the old format.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This merges in the ppc-kvm topic branch to get changes to
arch/powerpc code that are necessary for adding POWER9 KVM support.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Partially copied from commit df0698be14 ("ARM: stack protector:
change the canary value per task")
A new random value for the canary is stored in the task struct whenever
a new task is forked. This is meant to allow for different canary values
per task. On powerpc, GCC expects the canary value to be found in a global
variable called __stack_chk_guard. So this variable has to be updated
with the value stored in the task struct whenever a task switch occurs.
Because the variable GCC expects is global, this cannot work on SMP
unfortunately. So, on SMP, the same initial canary value is kept
throughout, making this feature a bit less effective although it is still
useful.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Partialy copied from commit c743f38013 ("ARM: initial stack protector
(-fstack-protector) support")
This is the very basic stuff without the changing canary upon
task switch yet. Just the Kconfig option and a constant canary
value initialized at boot time.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Implement xchg{u8,u16}{local,relaxed}, and
cmpxchg{u8,u16}{,local,acquire,relaxed}.
It works on all ppc.
remove volatile of first parameter in __cmpxchg_local and __cmpxchg
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Pan Xinhui <xinhui.pan@linux.vnet.ibm.com>
Acked-by: Boqun Feng <boqun.feng@gmail.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are no ibmebus driver that make use of legacy suspend/resume. This
patch removes the support for it from ibmebus framework, new ibmebus
driver (as unlikely as they are) wanting to use suspend/resume should
use dev_pm_ops.
Since there aren't any special bus specific things to do during
suspend/resume and since the PM core will automatically fallback
directly to using the device's PM ops if no bus PM ops are specified
there is no need to have any special ibmebus PM ops at all.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Invoke the kprobe handlers directly rather than through notify_die(), to
reduce path taken for handling kprobes. Similar to commit 6f6343f53d
("kprobes/x86: Call exception handlers directly from do_int3/do_debug").
While at it, rename post_kprobe_handler() to kprobe_post_handler() for
more uniform naming.
Reported-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 03465f899b ("powerpc: Use kprobe blacklist for exception
handlers") removed __kprobes annotation from some of the prototypes,
but left the kprobes header include directive unchanged. Remove it as it
is no longer needed.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These config changes build:
drivers/power/reset/gpio-poweroff.c
drivers/power/reset/gpio-restart.c
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Use of_property_read_u32 instead of the generic of_get_property to
simplify the code. In addition move the declaration of fs_baudrate
into get_baudrate because it's private to this function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Use of_property_read_u32 instead of the generic of_get_property to
simplify the code. In addition move the declaration of brgfreq
into get_brgfreq because it's private to this function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
[scottwood: minor whitespace fixes]
Signed-off-by: Scott Wood <oss@buserror.net>
Use of_property_read_u32 instead of the generic of_get_property to
simplify the code. In addition move the declaration of sysfreq
into fsl_get_sys_freq because it's private to this function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
The QEMU e500 board needs to enable CONFIG_E500 to correctly boot. QEMU
for ppc64 uses e5500/e6500 emulation, thus CONFIG_PPC_E500MC is required
as well.
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Define and set the POWER9 HFSCR doorbell bit so that guests can use
msgsndp.
ISA 3.0 calls this MSGP, so name it accordingly in the code.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
ISA 3.0 defines a new PECE (Power-saving mode Exit Cause Enable) field
in the LPCR (Logical Partitioning Control Register), called
LPCR_PECE_HVEE (Hypervisor Virtualization Exit Enable).
KVM code will need to know about this bit, so add a definition for it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
ISA 3.00 adds the logical PVR value 0x0f000005, so add a definition for
this.
Define PCR_ARCH_207 to reflect ISA 2.07 compatibility mode in the processor
compatibility register (PCR).
[paulus@ozlabs.org - moved dummy PCR_ARCH_300 value into next patch]
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This defines real-mode versions of opal_int_get_xirr(), opal_int_eoi()
and opal_int_set_mfrr(), for use by KVM real-mode code.
It also exports opal_int_set_mfrr() so that the modular part of KVM
can use it to send IPIs.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 requires the host to set up a partition table, which is a
table in memory indexed by logical partition ID (LPID) which
contains the pointers to page tables and process tables for the
host and each guest.
This factors out the initialization of the partition table into
a single function. This code was previously duplicated between
hash_utils_64.c and pgtable-radix.c.
This provides a function for setting a partition table entry,
which is used in early MMU initialization, and will be used by
KVM whenever a guest is created. This function includes a tlbie
instruction which will flush all TLB entries for the LPID and
all caches of the partition table entry for the LPID, across the
system.
This also moves a call to memblock_set_current_limit(), which was
in radix_init_partition_table(), but has nothing to do with the
partition table. By analogy with the similar code for hash, the
call gets moved to near the end of radix__early_init_mmu(). It
now gets called when running as a guest, whereas previously it
would only be called if the kernel is running as the host.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
The previous convention of keeping the files around until the CPU is dead
has not been preserved as there is no point to keep them available when the
cpu is going down. This makes the hotplug call symmetric.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: rt@linuxtronix.de
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/20161117183541.8588-17-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It is the reasonable expectation that if an executable file is not
readable there will be no way for a user without special privileges to
read the file. This is enforced in ptrace_attach but if ptrace
is already attached before exec there is no enforcement for read-only
executables.
As the only way to read such an mm is through access_process_vm
spin a variant called ptrace_access_vm that will fail if the
target process is not being ptraced by the current process, or
the current process did not have sufficient privileges when ptracing
began to read the target processes mm.
In the ptrace implementations replace access_process_vm by
ptrace_access_vm. There remain several ptrace sites that still use
access_process_vm as they are reading the target executables
instructions (for kernel consumption) or register stacks. As such it
does not appear necessary to add a permission check to those calls.
This bug has always existed in Linux.
Fixes: v1.0
Cc: stable@vger.kernel.org
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
After patch 4efca4ed0 ("kbuild: modversions for EXPORT_SYMBOL() for asm"),
asm exports can get modversions CRCs generated if they have C definitions
in asm-prototypes.h. This patch adds missing definitions for 32 and 64 bit
allmodconfig builds.
Fixes: 9445aa1a30 ("ppc: move exports to definitions")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The T4240RDB contains a W83793 hardware monitoring chip. Add a device
tree entry to make the driver attach to it, as the i2c-mpc bus driver
dropped support for class-based instantiation of devices a long time
ago.
Signed-off-by: Florian Larysch <fl@n621.de>
Signed-off-by: Scott Wood <oss@buserror.net>
There is a new bit, LPCR_PECE_HVEE (Hypervisor Virtualization Exit
Enable), which controls wakeup from STOP states on Hypervisor
Virtualization Interrupts (which happen to also be all external
interrupts in host or bare metal mode).
It needs to be set or we will miss wakeups.
Fixes: 9baaef0a22 ("powerpc/irq: Add support for HV virtualization interrupts")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Rename it to HVEE to match the name in the ISA]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
VSID 0 is bad address. Don't create slb entries on coproc fault for
bad address
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_pe_reset and eeh_reset_pe are two different functions in the same
file which do mostly the same thing. Not only is this confusing, but
potentially causes disrepancies in functionality, notably eeh_reset_pe
as it does not check return values for failure.
Refactor this into the following:
- eeh_pe_reset(): stays as is, performs a single operation, exported
- eeh_pe_reset_full(): new, full reset process that calls eeh_pe_reset()
- eeh_reset_pe(): removed and replaced by eeh_pe_reset_full()
- eeh_reset_pe_once(): removed
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PHB, PE (and by association MVE) numbers are printed as a mix of decimal
and hexadecimal throughout the kernel. This can be misleading, so make
them all hexadecimal.
Standardising on hex instead of dec because:
- PHB numbers are presented in hex in sysfs/debugfs (and lspci, etc)
- PE numbers are presented as hex in sysfs and parsed in hex in debugfs
The only place I think this could cause confusing are the messages during
boot, i.e.
pci 000a:01 : [PE# 000] Secondary bus 1 associated with PE#0
which can be a quick way to check PE numbers. pe_level_printk() will
only print two characters instead of three, so the above would be
pci 000a:01 : [PE# 00] Secondary bus 1 associated with PE#0
which gives a hint it's in hex.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Whenever a PE is initialised in powernv, opal_pci_eeh_freeze_clear() is
called. This is to remove any existing freeze, and has no negative side
effects if the PE is already in an unfrozen state. On PHB backends that
don't support this operation and return OPAL_UNSUPPORTED, this creates a
scary and misleading warning message.
Skip the warning message on init if OPAL_UNSUPPORTED is returned.
As far as I'm aware, this currently only affects NPUs.
Fixes: 313483d ("powerpc/powernv: Unfreeze PE on allocation")
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Drop duplicate header asm/iommu.h from book3s_64_vio_hv.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The hashed page table MMU in POWER processors can update the R
(reference) and C (change) bits in a HPTE at any time until the
HPTE has been invalidated and the TLB invalidation sequence has
completed. In kvmppc_h_protect, which implements the H_PROTECT
hypercall, we read the HPTE, modify the second doubleword,
invalidate the HPTE in memory, do the TLB invalidation sequence,
and then write the modified value of the second doubleword back
to memory. In doing so we could overwrite an R/C bit update done
by hardware between when we read the HPTE and when the TLB
invalidation completed. To fix this we re-read the second
doubleword after the TLB invalidation and OR in the (possibly)
new values of R and C. We can use an OR since hardware only ever
sets R and C, never clears them.
This race was found by code inspection. In principle this bug could
cause occasional guest memory corruption under host memory pressure.
Fixes: a8606e20e4 ("KVM: PPC: Handle some PAPR hcalls in the kernel", 2011-06-29)
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When switching from/to a guest that has a transaction in progress,
we need to save/restore the checkpointed register state. Although
XER is part of the CPU state that gets checkpointed, the code that
does this saving and restoring doesn't save/restore XER.
This fixes it by saving and restoring the XER. To allow userspace
to read/write the checkpointed XER value, we also add a new ONE_REG
specifier.
The visible effect of this bug is that the guest may see its XER
value being corrupted when it uses transactions.
Fixes: e4e3812150 ("KVM: PPC: Book3S HV: Add transactional memory support")
Fixes: 0a8eccefcb ("KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This keeps a per vcpu cache for recently page faulted MMIO entries.
On a page fault, if the entry exists in the cache, we can avoid some
time-consuming paths, for example, looking up HPT, locking HPTE twice
and searching mmio gfn from memslots, then directly call
kvmppc_hv_emulate_mmio().
In current implenment, we limit the size of cache to four. We think
it's enough to cover the high-frequency MMIO HPTEs in most case.
For example, considering the case of using virtio device, for virtio
legacy devices, one HPTE could handle notifications from up to
1024 (64K page / 64 byte Port IO register) devices, so one cache entry
is enough; for virtio modern devices, we always need one HPTE to handle
notification for each device because modern device would use a 8M MMIO
register to notify host instead of Port IO register, typically the
system's configuration should not exceed four virtio devices per
vcpu, four cache entry is also enough in this case. Of course, if needed,
we could also modify the macro to a module parameter in the future.
Signed-off-by: Yongji Xie <xyjxie@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently we mark a HPTE for emulated MMIO with HPTE_V_ABSENT bit
set as well as key 0x1f. However, those HPTEs may be conflicted with
the HPTE for real guest RAM page HPTE with key 0x1f when the page
get paged out.
This patch clears the key field of HPTE when the page is paged out,
then recover it when HPTE is re-established.
Signed-off-by: Yongji Xie <xyjxie@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Using list_move_tail() instead of list_del() + list_add_tail().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
A bunch of KVM functions are only called from assembler.
Give them prototypes in asm-prototypes.h
This reduces sparse warnings.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Squash a couple of sparse warnings by making things static.
Build tested.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Fixes marked for stable:
- Fix system reset interrupt winkle wakeups (Nicholas Piggin)
- Fix setting of AIL in hypervisor mode (Benjamin Herrenschmidt)
Fixes for code merged this cycle:
- Fix exception vector build with 2.23 era binutils (Hugh Dickins)
- Fix missing update of HID register on secondary CPUs (Aneesh Kumar K.V)
Other:
- Fix missing pr_cont()s in show_stack() (Michael Ellerman)
- Fix missing pr_cont()s in print_msr_bits() et. al. (Michael Ellerman)
- Fix missing pr_cont()s in show_regs() (Michael Ellerman)
- Fix missing pr_cont()s in instruction dump (Andrew Donnellan)
- Invalidate ERAT on tlbiel for POWER9 DD1 (Michael Neuling)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+6XC
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- fix system reset interrupt winkle wakeups
- fix setting of AIL in hypervisor mode
Fixes for code merged this cycle:
- fix exception vector build with 2.23 era binutils
- fix missing update of HID register on secondary CPUs
Other:
- fix missing pr_cont()s
- invalidate ERAT on tlbiel for POWER9 DD1"
* tag 'powerpc-4.9-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fix missing update of HID register on secondary CPUs
powerpc/mm/radix: Invalidate ERAT on tlbiel for POWER9 DD1
powerpc/64: Fix setting of AIL in hypervisor mode
powerpc/oops: Fix missing pr_cont()s in instruction dump
powerpc/oops: Fix missing pr_cont()s in show_regs()
powerpc/oops: Fix missing pr_cont()s in print_msr_bits() et. al.
powerpc/oops: Fix missing pr_cont()s in show_stack()
powerpc: Fix exception vector build with 2.23 era binutils
powerpc/64s: Fix system reset interrupt winkle wakeups
We need to update on secondaries for the selected MMU mode.
Fixes: ad410674f5 ("powerpc/mm: Update the HID bit when switching from radix to hash")
Reported-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ibm_pa_features array consists of structures that describe which bit
and byte in the ibm,pa-features property toggles one or more flags in
either the CPU, MMU, or user visible feature flags.
Each one consists of 7 values, which are all unsigned long, int or char,
meaning the compiler gives us no warning if we assign the wrong values
to the wrong elements. In fact we have had a bug here in the past, where
we were setting incorrect bits, see commit 6997e57d69 ("powerpc:
scan_features() updates incorrect bits for REAL_LE").
So switch to using named initialisers for the structure elements, to
reduce the likelihood of future bugs, and hopefully improve readability
also.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
These are the PPC optimised versions of various crypto algorithms, so we
should turn them on by default to get test coverage.
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The IBMEBUS code supports the GX bus found on Power7 and earlier CPUs.
On Power8 it has been replaced, and so we have no need for it.
We don't actually have a config symbol for Power8 vs Power7 etc., but
we only support booting little endian on Power8 or later, so use that as
a reasonable approximation.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When ending an oops, don't clear die_owner unless the nest count
went to zero. This prevents a second nested oops from hanging forever
on the die_lock.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When exiting xmon with 'x' (exit and recover), oops_begin bails
out immediately, but die then calls __die() and oops_end(), which
cause a lot of bad things to happen.
If the debugger was attached then went to graceful recovery, exit
from die() immediately.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add an option to use thin archives to build the kernel.
Thin archives are explained in commit a5967db9af ("kbuild: allow
architectures to use thin archives instead of ld -r").
This is a gradual way to introduce the option to testers.
Some change to the way we invoke ar is required so it can be used
by scripts/link-vmlinux.sh.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Make it an explicit option not dependant on COMPILE_TEST]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Under some configs we need to explicitly include cpu_has_feature.h,
otherwise we fail with:
arch/powerpc/lib/sstep.c:1992:7: error: implicit declaration of function 'cpu_has_feature'
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pasrsing of data written to the dlpar file in sysfs does not correctly
account for the possibility of reading past the end of the buffer. The code
assumes that all pieces of the command witten to the sysfs file are present
in the form "<resource> <action> <id_type> <id>".
Correct this by updating the buffer parsing code to make a local copy and
use the strsep() and sysfs_streq() routines to parse the buffer. This patch
also separates the parsing code into subroutines for each piece of the
command.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove the unused but set variable srr1 in save_mce_event() to
fix the following GCC warning when building with 'W=1':
arch/powerpc/kernel/mce.c:75:11: warning: variable 'srr1' set but not used
It has never been used.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix two [-Wold-style-declaration] GCC warnings by moving the inline
keyword before the return type.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
MIN_HUGEPTE_SHIFT hasn't been used since commit d1837cba5d
("powerpc/mm: Cleanup initialization of hugepages on powerpc")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On POWER9 DD1, when we do a local TLB invalidate we also need to explicitly
invalidate the ERAT.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No need to duplicate the same define everywhere. Since
the only user is stop-machine and the only provider is
s390, we can use a default implementation of cpu_relax_yield()
in sched.h.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: kvm@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-s390 <linux-s390@vger.kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: sparclinux@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1479298985-191589-1-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Version 3.00 of the ISA states that the PATS (partition table size) field
of the PTCR (partition table control register) and the PRTS (process table
size) field of the partition table entry must both be less than or equal
to 24. However the actual size of the partition and process tables is equal
to 2 to the power of 12 plus the PATS and PRTS fields, respectively. This
means that the max allowable size of each of these tables is 2^36 or 64GB
for both.
Thus when checking the size shift for each we should be checking for values
of greater than 36 instead of the current check for shifts larger than 24
and 23.
Fixes: 2bfd65e45e
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Useful to be able to dump the kernel hash page table to check
which pages are hashed along with their sizes and other details.
Add a debugfs file to check the hash page table. If radix is enabled
(and so there is no hash page table) then this file doesn't exist. To
use this the PPC_PTDUMP config option must be selected.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
[mpe: Fix build with SPARSEMEM_VMEMMAP=n & PSERIES=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Useful to be able to dump the kernels page tables to check permissions
and memory types - derived from arm64's implementation.
Add a debugfs file to check the page tables. To use this the PPC_PTDUMP
config option must be selected.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently there's some CMO (Cooperative Memory Overcommit) code, in
plpar_wrappers.h. Some of it is #ifdef CONFIG_PSERIES and some of it
isn't. The end result being if a file includes plpar_wrappers.h it won't
build with CONFIG_PSERIES=n.
Fix it by moving the CMO code into platforms/pseries. The two hcall
wrappers can just be moved into their only caller, cmm.c, and the
accessors can go in pseries.h.
Note we need the accessors because cmm.c can be built as a module, so
there needs to be a split between the built-in code vs the module, and
that's achieved by using those accessors.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As there are no users left, we can remove cpu_relax_lowlatency()
implementations from every architecture.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Cc: <linux-arch@vger.kernel.org>
Link: http://lkml.kernel.org/r/1477386195-32736-6-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For spinning loops people do often use barrier() or cpu_relax().
For most architectures cpu_relax and barrier are the same, but on
some architectures cpu_relax can add some latency.
For example on power,sparc64 and arc, cpu_relax can shift the CPU
towards other hardware threads in an SMT environment.
On s390 cpu_relax does even more, it uses an hypercall to the
hypervisor to give up the timeslice.
In contrast to the SMT yielding this can result in larger latencies.
In some places this latency is unwanted, so another variant
"cpu_relax_lowlatency" was introduced. Before this is used in more
and more places, lets revert the logic and provide a cpu_relax_yield
that can be called in places where yielding is more important than
latency. By default this is the same as cpu_relax on all architectures.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1477386195-32736-2-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This changes the way that we support the new ISA v3.00 HPTE format.
Instead of adapting everything that uses HPTE values to handle either
the old format or the new format, depending on which CPU we are on,
we now convert explicitly between old and new formats if necessary
in the low-level routines that actually access HPTEs in memory.
This limits the amount of code that needs to know about the new
format and makes the conversions explicit. This is OK because the
old format contains all the information that is in the new format.
This also fixes operation under a hypervisor, because the H_ENTER
hypercall (and other hypercalls that deal with HPTEs) will continue
to require the HPTE value to be supplied in the old format. At
present the kernel will not boot in HPT mode on POWER9 under a
hypervisor.
This fixes and partially reverts commit 50de596de8
("powerpc/mm/hash: Add support for Power9 Hash", 2016-04-29).
Fixes: 50de596de8 ("powerpc/mm/hash: Add support for Power9 Hash")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit d3cbff1b5 "powerpc: Put exception configuration in a common place"
broke the setting of the AIL bit (which enables taking exceptions with
the MMU still on) on all processors, moving it incorrectly to a function
called only on the boot CPU. This was correct for the guest case but
not when running in hypervisor mode.
This fixes it by partially reverting that commit, putting the setting
back in cpu_ready_for_interrupts()
Fixes: d3cbff1b5a ("powerpc: Put exception configuration in a common place")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Only s390 and powerpc have hardware facilities allowing to measure
cputimes scaled by frequency. On all other architectures
utimescaled/stimescaled are equal to utime/stime (however they are
accounted separately).
Remove {u,s}timescaled accounting on all architectures except
powerpc and s390, where those values are explicitly accounted
in the proper places.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20161031162143.GB12646@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently cputime_to_scaled() just return it's argument on
all implementations, we don't need to call this function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1479175612-14718-3-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since commit:
cf9efce0ce ("powerpc: Account time using timebase rather than PURR")
cputime_last_delta is not initialized to other value than 0, hence it's
not used except zero check and cputime_to_scaled() just returns
the argument.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1479175612-14718-2-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts storcenter_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts pseries_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts ppc6xx_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts ppc64e_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts ppc64_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts pmac32_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
This patch disables deprecated IDE subsystem in pasemi_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts maple_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts g5_defconfig to use libata PATA drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts chrp32_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts cell_defconfig to use libata PATA drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts amigaone_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Add comment clarifying that vio_find_node() takes a reference to the
embedded struct device which needs to be dropped after use.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make sure to drop any reference taken by bus_find_device() when creating
devices during init and driver registration.
Fixes: 55347cc996 ("[POWERPC] ibmebus: Add device creation and bus probing based on of_device")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make sure to drop any reference taken by bus_find_device() in the sysfs
callbacks that are used to create and destroy devices based on
device-tree entries.
Fixes: 6bccf755ff ("[POWERPC] ibmebus: dynamic addition/removal of adapters, some code cleanup")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This condenses the opal node searching into a single function that finds
all compatible nodes, instead of just searching the ibm,opal children,
for ipmi, flash, and prd similar to how opal-i2c nodes are found.
Signed-off-by: Jack Miller <jack@codezen.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Load monitored is no longer supported on POWER9 so let's remove the
code.
This reverts commit bd3ea317fd ("powerpc: Load Monitor Register
Support").
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No one uses reiserfs much these days, or is likely to in future. So drop
it from pseries and powernv defconfigs to save time and space. It's
still enabled in ppc64_defconfig so we get some build coverage.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In ISA v2.05, the tlbiel instruction takes two arguments, RB and L:
tlbiel RB,L
+---------+---------+----+---------+---------+---------+----+
| 31 | / | L | / | RB | 274 | / |
| 31 - 26 | 25 - 22 | 21 | 20 - 16 | 15 - 11 | 10 - 1 | 0 |
+---------+---------+----+---------+---------+---------+----+
In ISA v2.06 tlbiel takes only one argument, RB:
tlbiel RB
+---------+---------+---------+---------+---------+----+
| 31 | / | / | RB | 274 | / |
| 31 - 26 | 25 - 21 | 20 - 16 | 15 - 11 | 10 - 1 | 0 |
+---------+---------+---------+---------+---------+----+
And in ISA v3.00 tlbiel takes five arguments:
tlbiel RB,RS,RIC,PRS,R
+---------+---------+----+---------+----+----+---------+---------+----+
| 31 | RS | / | RIC |PRS | R | RB | 274 | / |
| 31 - 26 | 25 - 21 | 20 | 19 - 18 | 17 | 16 | 15 - 11 | 10 - 1 | 0 |
+---------+---------+----+---------+----+----+---------+---------+----+
However the assembler also accepts "tlbiel RB", and generates
"tlbiel RB,r0,0,0,0".
As you can see above the L field from the v2.05 encoding overlaps with the
reserved field of the v2.06 encoding, and the low bit of the RS field of the
v3.00 encoding.
Currently in __tlbiel() we generate two tlbiel instructions manually using hex
constants. In the first case, for MMU_PAGE_4K, we generate "tlbiel RB,0", which
is safe in all cases, because the L bit is zero.
However in the default case we generate "tlbiel RB,1", therefore setting bit 21
to 1.
This is not an actual bug on v2.06 processors, because the CPU ignores the value
of the reserved field. However software is supposed to encode the reserved
fields as zero to enable forward compatibility.
On v3.00 processors setting bit 21 to 1 and no other bits of RS, means we are
using r1 for the value of RS.
Although it's not obvious, the code sets the IS field (bits 10-11) to 0 (by
omission), and L=1, in the va value, which is passed as RB. We also pass R=0 in
the instruction.
The combination of IS=0, L=1 and R=0 means the value of RS is not used, so even
on ISA v3.00 there is no actual bug.
We should still fix it, as setting a reserved bit on v2.06 is naughty, and we
are only avoiding a bug on v3.00 by accident rather than design. Use
ASM_FTR_IFSET() to generate the single argument form on ISA v2.06 and later, and
the two argument form on pre v2.06.
Although there may be very old toolchains which don't understand tlbiel, we have
other code in the tree which has been using tlbiel for over five years, and no
one has reported any build failures, so just let the assembler generate the
instructions.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Rewrite change log, use IFSET instead of IFCLR]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we're not compiling for a specific CPU, ie. none of the
CONFIG_POWERx_CPU options are set, and CONFIG_GENERIC_CPU *is* set, we
currently don't pass any -mcpu option to the compiler. This means the
compiler builds for a "generic" Power CPU.
But back in 2014 we dropped support for pre power4 CPUs in commit
468a33028e ("powerpc: Drop support for pre-POWER4 cpus").
Given that, there's no point in building the kernel to run on pre power4
cpus. So update the flags we pass to the compiler when
CONFIG_GENERIC_CPU is set, to specify -mcpu=power4.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a config option that can help exercise the case when
the kernel is not running at PAGE_OFFSET.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
An hcall was recently added that does exactly what we need during kexec
- it clears the entire MMU hash table, ignoring any VRMA mappings.
Try it and fall back to the old method if we get a failure.
On a POWER8 box with 5TB of memory, this reduces the time it takes to
kexec a new kernel from from 4 minutes to 1 minute.
Signed-off-by: Anton Blanchard <anton@samba.org>
Tested-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
[mpe: Split into separate functions and tweak function naming]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This halves the exception table size on 64-bit builds, and it allows
build-time sorting of exception tables to work on relocated kernels.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Minor asm fixups and bits to keep the selftests working]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This macro is taken from s390, and allows more flexibility in
changing exception table format.
mpe: Put it in ppc_asm.h and only define one version using
stringinfy_in_c(). Add some empty definitions and headers to keep the
selftests happy.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We haven't seen these before, but the soon to be merged relative
exception tables support causes them to be generated.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There's no reason to #error if we include ppc_asm.h in asm files, the
ifdef already prevents any problems.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Exception handlers are aligned to 128 bytes (L1 cache) on 64s, which is
overkill. It can reduce the icache footprint of any individual exception
path. However taken as a whole, the expansion in icache footprint seems
likely to be counter-productive and cause more total misses.
Create IFETCH_ALIGN_SHIFT/BYTES, which should give optimal ifetch
alignment with much more reasonable alignment. This saves 1792 bytes
from head_64.o text with an allmodconfig build.
Other subarchitectures should define appropriate IFETCH_ALIGN_SHIFT
values if this becomes more widely used.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are three #ifdef CONFIG_PPC_BOOK3E sections in nohash/64/pgtable.h.
And there should be no configurations possible which use nohash/64/pgtable.h
but don't also enable CONFIG_PPC_BOOK3E.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Rui Teng <rui.teng@linux.vnet.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since the KERN_CONT changes, the current code in show_instructions()
prints out a whole bunch of unnecessary newlines. Change occurrences of
printk("\n") to pr_cont("\n"). While we're here, change all the other
cases of printk(KERN_CONT ...) to pr_cont() as well.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix up our oops output by converting continuation lines to use
pr_cont(). Some of these are dubious, eg. printing a continuation line
which starts with a newline, but seem to work OK for now. This whole
function needs a rewrite in the next release.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since the KERN_CONT changes these are being horribly split across lines,
for example:
MSR: 8000000000009033 <
SF,EE
,ME,IR
,DR,RI
,LE>
So fix it by using pr_cont() where appropriate.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Previously we got away with printing the stack trace in multiple pieces
and it usually looked right. But since commit 4bcc595ccd ("printk:
reinstate KERN_CONT for printing continuation lines"), KERN_CONT is now
required when printing continuation lines. Use pr_cont() as appropriate.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The changes to use gas sections for constructing the exception vectors
causes a build break when using binutils 2.23:
arch/powerpc/kernel/exceptions-64s.S:770: Error: operand out of range
(0xffffffffffff8100 is not between 0x0000000000000000 and 0x000000000000ffff)
And so on.
Reported by Hugh with binutils-2.23.2-8.1.4.ppc64 from openSUSE 13.1 and
also Naveen & Denis using 2.23.52.0.1-26.el7 from RHEL 7. Strangely
binutils 2.22 (what I test with) is not affected.
This is caused by the use of @l in LOAD_HANDLER(). The @l was only
recently added in commit a24553dd02 ("powerpc/pseries: Remove
unnecessary syscall trampoline").
Luckily the gas section changes split out the LOAD_SYSCALL_HANDLER()
macro, which means we actually *don't* need to use @l in LOAD_HANDLER()
any more, only in LOAD_SYSCALL_HANDLER().
So drop the @l from LOAD_HANDLER().
Fixes: 57f266497d ("powerpc: Use gas sections for arranging exception vectors")
Signed-off-by: Hugh Dickins <hughd@google.com>
[mpe: Add gory details to change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Wakeups from winkle set the low bit of the HSPRG0 register, to
distinguish it from other sleep states. This is also the PACA pointer.
The system reset exception handler fails to mask this bit away before
using this value before using it as the PACA pointer.
Fix this by adding a new type of exception prolog macro where we already
have the PACA set in r13, and have the system reset vector mask it out.
The winkle wakeup handler will store the masked value back into HSPRG0.
Fixes: fb479e44a9 ("powerpc/64s: relocation, register save fixes for system reset interrupt")
Cc: stable@vger.kernel.org # v3.0+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull networking fixes from David Miller:
"Lots of fixes, mostly drivers as is usually the case.
1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
Khoroshilov.
2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
Pedersen.
3) Don't put aead_req crypto struct on the stack in mac80211, from
Ard Biesheuvel.
4) Several uninitialized variable warning fixes from Arnd Bergmann.
5) Fix memory leak in cxgb4, from Colin Ian King.
6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.
7) Several VRF semantic fixes from David Ahern.
8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.
9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.
10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.
11) Fix stale link state during failover in NCSCI driver, from Gavin
Shan.
12) Fix netdev lower adjacency list traversal, from Ido Schimmel.
13) Propvide proper handle when emitting notifications of filter
deletes, from Jamal Hadi Salim.
14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.
15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.
16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.
17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.
18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
Leitner.
19) Revert a netns locking change that causes regressions, from Paul
Moore.
20) Add recursion limit to GRO handling, from Sabrina Dubroca.
21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.
22) Avoid accessing stale vxlan/geneve socket in data path, from
Pravin Shelar"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
geneve: avoid using stale geneve socket.
vxlan: avoid using stale vxlan socket.
qede: Fix out-of-bound fastpath memory access
net: phy: dp83848: add dp83822 PHY support
enic: fix rq disable
tipc: fix broadcast link synchronization problem
ibmvnic: Fix missing brackets in init_sub_crq_irqs
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
net/mlx4_en: Save slave ethtool stats command
net/mlx4_en: Fix potential deadlock in port statistics flow
net/mlx4: Fix firmware command timeout during interrupt test
net/mlx4_core: Do not access comm channel if it has not yet been initialized
net/mlx4_en: Fix panic during reboot
net/mlx4_en: Process all completions in RX rings after port goes up
net/mlx4_en: Resolve dividing by zero in 32-bit system
net/mlx4_core: Change the default value of enable_qos
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
...
Commit 01cfbad "ipv4: Update parameters for csum_tcpudp_magic to their
original types" changed parameters for csum_tcpudp_magic and
csum_tcpudp_nofold for many platforms but not for PowerPC.
Fixes: 01cfbad "ipv4: Update parameters for csum_tcpudp_magic to their original types"
Cc: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes marked for stable:
- Convert cmp to cmpd in idle enter sequence (Segher Boessenkool)
- cxl: Fix leaking pid refs in some error paths (Vaibhav Jain)
- Re-fix race condition between going idle and entering guest (Paul Mackerras)
- Fix race condition in setting lock bit in idle/wakeup code (Paul Mackerras)
- radix: Use tlbiel only if we ever ran on the current cpu (Aneesh Kumar K.V)
- relocation, register save fixes for system reset interrupt (Nicholas Piggin)
Fixes for code merged this cycle:
- Fix CONFIG_ALIVEC typo in restore_tm_state() (Valentin Rothberg)
- KVM: PPC: Book3S HV: Fix build error when SMP=n (Michael Ellerman)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dnRQ
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- Convert cmp to cmpd in idle enter sequence (Segher Boessenkool)
- cxl: Fix leaking pid refs in some error paths (Vaibhav Jain)
- Re-fix race condition between going idle and entering guest (Paul Mackerras)
- Fix race condition in setting lock bit in idle/wakeup code (Paul Mackerras)
- radix: Use tlbiel only if we ever ran on the current cpu (Aneesh Kumar K.V)
- relocation, register save fixes for system reset interrupt (Nicholas Piggin)
Fixes for code merged this cycle:
- Fix CONFIG_ALIVEC typo in restore_tm_state() (Valentin Rothberg)
- KVM: PPC: Book3S HV: Fix build error when SMP=n (Michael Ellerman)"
* tag 'powerpc-4.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: relocation, register save fixes for system reset interrupt
powerpc/mm/radix: Use tlbiel only if we ever ran on the current cpu
powerpc/process: Fix CONFIG_ALIVEC typo in restore_tm_state()
powerpc/64: Fix race condition in setting lock bit in idle/wakeup code
powerpc/64: Re-fix race condition between going idle and entering guest
cxl: Fix leaking pid refs in some error paths
powerpc: Convert cmp to cmpd in idle enter sequence
KVM: PPC: Book3S HV: Fix build error when SMP=n
Pull perf fixes from Ingo Molnar:
"Misc kernel fixes: a virtualization environment related fix, an uncore
PMU driver removal handling fix, a PowerPC fix and new events for
Knights Landing"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Honour the CPUID for number of fixed counters in hypervisors
perf/powerpc: Don't call perf_event_disable() from atomic context
perf/core: Protect PMU device removal with a 'pmu_bus_running' check, to fix CONFIG_DEBUG_TEST_DRIVER_REMOVE=y kernel panic
perf/x86/intel/cstate: Add C-state residency events for Knights Landing
The trinity syscall fuzzer triggered following WARN() on powerpc:
WARNING: CPU: 9 PID: 2998 at arch/powerpc/kernel/hw_breakpoint.c:278
...
NIP [c00000000093aedc] .hw_breakpoint_handler+0x28c/0x2b0
LR [c00000000093aed8] .hw_breakpoint_handler+0x288/0x2b0
Call Trace:
[c0000002f7933580] [c00000000093aed8] .hw_breakpoint_handler+0x288/0x2b0 (unreliable)
[c0000002f7933630] [c0000000000f671c] .notifier_call_chain+0x7c/0xf0
[c0000002f79336d0] [c0000000000f6abc] .__atomic_notifier_call_chain+0xbc/0x1c0
[c0000002f7933780] [c0000000000f6c40] .notify_die+0x70/0xd0
[c0000002f7933820] [c00000000001a74c] .do_break+0x4c/0x100
[c0000002f7933920] [c0000000000089fc] handle_dabr_fault+0x14/0x48
Followed by a lockdep warning:
===============================
[ INFO: suspicious RCU usage. ]
4.8.0-rc5+ #7 Tainted: G W
-------------------------------
./include/linux/rcupdate.h:556 Illegal context switch in RCU read-side critical section!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
2 locks held by ls/2998:
#0: (rcu_read_lock){......}, at: [<c0000000000f6a00>] .__atomic_notifier_call_chain+0x0/0x1c0
#1: (rcu_read_lock){......}, at: [<c00000000093ac50>] .hw_breakpoint_handler+0x0/0x2b0
stack backtrace:
CPU: 9 PID: 2998 Comm: ls Tainted: G W 4.8.0-rc5+ #7
Call Trace:
[c0000002f7933150] [c00000000094b1f8] .dump_stack+0xe0/0x14c (unreliable)
[c0000002f79331e0] [c00000000013c468] .lockdep_rcu_suspicious+0x138/0x180
[c0000002f7933270] [c0000000001005d8] .___might_sleep+0x278/0x2e0
[c0000002f7933300] [c000000000935584] .mutex_lock_nested+0x64/0x5a0
[c0000002f7933410] [c00000000023084c] .perf_event_ctx_lock_nested+0x16c/0x380
[c0000002f7933500] [c000000000230a80] .perf_event_disable+0x20/0x60
[c0000002f7933580] [c00000000093aeec] .hw_breakpoint_handler+0x29c/0x2b0
[c0000002f7933630] [c0000000000f671c] .notifier_call_chain+0x7c/0xf0
[c0000002f79336d0] [c0000000000f6abc] .__atomic_notifier_call_chain+0xbc/0x1c0
[c0000002f7933780] [c0000000000f6c40] .notify_die+0x70/0xd0
[c0000002f7933820] [c00000000001a74c] .do_break+0x4c/0x100
[c0000002f7933920] [c0000000000089fc] handle_dabr_fault+0x14/0x48
While it looks like the first WARN() is probably valid, the other one is
triggered by disabling event via perf_event_disable() from atomic context.
The event is disabled here in case we were not able to emulate
the instruction that hit the breakpoint. By disabling the event
we unschedule the event and make sure it's not scheduled back.
But we can't call perf_event_disable() from atomic context, instead
we need to use the event's pending_disable irq_work method to disable it.
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20161026094824.GA21397@krava
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch does a couple of things. First of all, powernv immediately
explodes when running a relocated kernel, because the system reset
exception for handling sleeps does not do correct relocated branches.
Secondly, the sleep handling code trashes the condition and cfar
registers, which we would like to preserve for debugging purposes (for
non-sleep case exception).
This patch changes the exception to use the standard format that saves
registers before any tests or branches are made. It adds the test for
idle-wakeup as an "extra" to break out of the normal exception path.
Then it branches to a relocated idle handler that calls the various
idle handling functions.
After this patch, POWER8 CPU simulator now boots powernv kernel that is
running at non-zero.
Fixes: 948cf67c47 ("powerpc: Add NAP mode support on Power7 in HV mode")
Cc: stable@vger.kernel.org # v3.0+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Before this patch, we used tlbiel, if we ever ran only on this core.
That was mostly derived from the nohash usage of the same. But is
incorrect, the ISA 3.0 clarifies tlbiel such that:
"All TLB entries that have all of the following properties are made
invalid on the thread executing the tlbiel instruction"
ie. tlbiel only invalidates TLB entries on the current thread. So if the
mm has been used on any other thread (aka. cpu) then we must broadcast
the invalidate.
This bug could lead to invalid TLB entries if a program runs on multiple
threads of a core.
Hence use tlbiel, if we only ever ran on only the current cpu.
Fixes: 1a472c9dba ("powerpc/mm/radix: Add tlbflush routines")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It should be ALTIVEC, not ALIVEC.
Cyril explains: If a thread performs a transaction with altivec and then
gets preempted for whatever reason, this bug may cause the kernel to not
re-enable altivec when that thread runs again. This will result in an
altivec unavailable fault, when that fault happens inside a user
transaction the kernel has no choice but to enable altivec and doom the
transaction.
The result is that transactions using altivec may get aborted more often
than they should.
The difficulty in catching this with a selftest is my deliberate use of
the word may above. Optimisations to avoid FPU/altivec/VSX faults mean
that the kernel will always leave them on for 255 switches. This code
prevents the kernel turning it off if it got to the 256th switch (and
userspace was transactional).
Fixes: dc16b553c9 ("powerpc: Always restore FPU/VEC/VSX if hardware transactional memory in use")
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Its all generic atomic_long_t stuff now.
Tested-by: Jason Low <jason.low2@hpe.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This fixes a race condition where one thread that is entering or
leaving a power-saving state can inadvertently ignore the lock bit
that was set by another thread, and potentially also clear it.
The core_idle_lock_held function is called when the lock bit is
seen to be set. It polls the lock bit until it is clear, then
does a lwarx to load the word containing the lock bit and thread
idle bits so it can be updated. However, it is possible that the
value loaded with the lwarx has the lock bit set, even though an
immediately preceding lwz loaded a value with the lock bit clear.
If this happens then we go ahead and update the word despite the
lock bit being set, and when called from pnv_enter_arch207_idle_mode,
we will subsequently clear the lock bit.
No identifiable misbehaviour has been attributed to this race.
This fixes it by checking the lock bit in the value loaded by the
lwarx. If it is set then we just go back and keep on polling.
Fixes: b32aadc1a8 ("powerpc/powernv: Fix race in updating core_idle_state")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 8117ac6a6c ("powerpc/powernv: Switch off MMU before entering
nap/sleep/rvwinkle mode", 2014-12-10) fixed a race condition where one
thread entering a KVM guest could switch the MMU context to the guest
while another thread was still in host kernel context with the MMU on.
That commit moved the point where a thread entering a power-saving
mode set its kvm_hstate.hwthread_state field in its PACA to
KVM_HWTHREAD_IN_IDLE from a point where the MMU was on to after the
MMU had been switched off. That commit also added a comment
explaining that we have to switch to real mode before setting
hwthread_state to avoid this race.
Nevertheless, commit 4eae2c9ae5 ("powerpc/powernv: Make
pnv_powersave_common more generic", 2016-07-08) subsequently moved
the setting of hwthread_state back to a point where the MMU is on,
thus reintroducing the race, despite the comment saying that this
should not be done being included in full in the context lines of
the patch that did it.
This fixes the race again and adds a bigger and shoutier comment
explaining the potential race condition.
Fixes: 4eae2c9ae5 ("powerpc/powernv: Make pnv_powersave_common more generic")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Shreyas B. Prabhu <shreyasbp@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes marked for stable:
- Prevent unlikely crash in copro_calculate_slb() (Frederic Barrat)
- cxl: Prevent adapter reset if an active context exists (Vaibhav Jain)
Fixes for code merged this cycle:
- Fix boot on systems with uncompressed kernel image (Heiner Kallweit)
- Drop dump_numa_memory_topology() (Michael Ellerman)
- Fix numa topology console print (Aneesh Kumar K.V)
- Ignore the pkey system calls for now (Stephen Rothwell)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=39+z
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- Prevent unlikely crash in copro_calculate_slb() (Frederic Barrat)
- cxl: Prevent adapter reset if an active context exists (Vaibhav Jain)
Fixes for code merged this cycle:
- Fix boot on systems with uncompressed kernel image (Heiner Kallweit)
- Drop dump_numa_memory_topology() (Michael Ellerman)
- Fix numa topology console print (Aneesh Kumar K.V)
- Ignore the pkey system calls for now (Stephen Rothwell)"
* tag 'powerpc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Ignore the pkey system calls for now
powerpc: Fix numa topology console print
powerpc/mm: Drop dump_numa_memory_topology()
cxl: Prevent adapter reset if an active context exists
powerpc/boot: Fix boot on systems with uncompressed kernel image
powerpc/mm: Prevent unlikely crash in copro_calculate_slb()
PowerPC's "cmp" instruction has four operands. Normally people write
"cmpw" or "cmpd" for the second cmp operand 0 or 1. But, frequently
people forget, and write "cmp" with just three operands.
With older binutils this is silently accepted as if this was "cmpw",
while often "cmpd" is wanted. With newer binutils GAS will complain
about this for 64-bit code. For 32-bit code it still silently assumes
"cmpw" is what is meant.
In this instance the code comes directly from ISA v2.07, including the
cmp, but cmpd is correct. Backport to stable so that new toolchains can
build old kernels.
Fixes: 948cf67c47 ("powerpc: Add NAP mode support on Power7 in HV mode")
Cc: stable@vger.kernel.org # v3.0
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 5d375199ea ("KVM: PPC: Book3S HV: Set server for passed-through
interrupts") broke the SMP=n build:
arch/powerpc/kvm/book3s_hv_rm_xics.c:758:2: error: implicit declaration of function 'get_hard_smp_processor_id'
That is because we lost the implicit include of asm/smp.h, so include it
explicitly to get the definition for get_hard_smp_processor_id().
Fixes: 5d375199ea ("KVM: PPC: Book3S HV: Set server for passed-through interrupts")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge the gup_flags cleanups from Lorenzo Stoakes:
"This patch series adjusts functions in the get_user_pages* family such
that desired FOLL_* flags are passed as an argument rather than
implied by flags.
The purpose of this change is to make the use of FOLL_FORCE explicit
so it is easier to grep for and clearer to callers that this flag is
being used. The use of FOLL_FORCE is an issue as it overrides missing
VM_READ/VM_WRITE flags for the VMA whose pages we are reading
from/writing to, which can result in surprising behaviour.
The patch series came out of the discussion around commit 38e0885465
("mm: check VMA flags to avoid invalid PROT_NONE NUMA balancing"),
which addressed a BUG_ON() being triggered when a page was faulted in
with PROT_NONE set but having been overridden by FOLL_FORCE.
do_numa_page() was run on the assumption the page _must_ be one marked
for NUMA node migration as an actual PROT_NONE page would have been
dealt with prior to this code path, however FOLL_FORCE introduced a
situation where this assumption did not hold.
See
https://marc.info/?l=linux-mm&m=147585445805166
for the patch proposal"
Additionally, there's a fix for an ancient bug related to FOLL_FORCE and
FOLL_WRITE by me.
[ This branch was rebased recently to add a few more acked-by's and
reviewed-by's ]
* gup_flag-cleanups:
mm: replace access_process_vm() write parameter with gup_flags
mm: replace access_remote_vm() write parameter with gup_flags
mm: replace __access_remote_vm() write parameter with gup_flags
mm: replace get_user_pages_remote() write/force parameters with gup_flags
mm: replace get_user_pages() write/force parameters with gup_flags
mm: replace get_vaddr_frames() write/force parameters with gup_flags
mm: replace get_user_pages_locked() write/force parameters with gup_flags
mm: replace get_user_pages_unlocked() write/force parameters with gup_flags
mm: remove write/force parameters from __get_user_pages_unlocked()
mm: remove write/force parameters from __get_user_pages_locked()
mm: remove gup_flags FOLL_WRITE games from __get_user_pages()
This removes the 'write' argument from access_process_vm() and replaces
it with 'gup_flags' as use of this function previously silently implied
FOLL_FORCE, whereas after this patch callers explicitly pass this flag.
We make this explicit as use of FOLL_FORCE can result in surprising
behaviour (and hence bugs) within the mm subsystem.
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eliminates warning messages:
<stdin>:1316:2: warning: #warning syscall pkey_mprotect not implemented [-Wcpp]
<stdin>:1319:2: warning: #warning syscall pkey_alloc not implemented [-Wcpp]
<stdin>:1322:2: warning: #warning syscall pkey_free not implemented [-Wcpp]
Hopefully we will remember to revert this commit if we ever implement
them.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At boot we dump the NUMA memory topology in dump_numa_memory_topology(),
at KERN_DEBUG level, resulting in output like:
Node 0 Memory: 0x0-0x100000000
Node 1 Memory: 0x100000000-0x200000000
Which is nice enough, but immediately after that we iterate over each
node and call setup_node_data(), which also prints out the node ranges,
at KERN_INFO, giving eg:
numa: Initmem setup node 0 [mem 0x00000000-0xffffffff]
numa: Initmem setup node 1 [mem 0x100000000-0x1ffffffff]
Additionally dump_numa_memory_topology() does not use KERN_CONT
correctly, resulting in split output lines on recent kernels.
So drop dump_numa_memory_topology() as superfluous chatter.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
