Currently, if we request for frequency greater than maximum possible, spi driver
returns error.
For example, if the spi block src frequency is 333/4 MHz, i.e. 83.33.. MHz,
maximum frequency programmable would be src/2. Which would come around 41.6...
It is difficult to pass frequency in these figures. We normally try to program
in round figures, like 42 MHz and it should get programmed to <=
requested_frequency, i.e. 41.6...
For this to happen, we must not return error even if requested freq is higher
than max possible. But should program it to max possible.
Reported-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix out-of-space checking, addressing a warning and potential resource
leak when resizing the filesystem down while allocating blocks.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Reviewed-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
may_commit_transaction() calls
spin_lock(&space_info->lock);
spin_lock(&delayed_rsv->lock);
and update_global_block_rsv() calls
spin_lock(&block_rsv->lock);
spin_lock(&sinfo->lock);
Lockdep complains about this at run time.
Everywhere except in update_global_block_rsv(), the space_info lock is
the outer lock, therefore the locking order in update_global_block_rsv()
is changed.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
I was seeing root_list corruption on unmount during fs resize in 3.4-rc4; add
correct locking to address this.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_map_block sets mirror_num, so that the repair code knows eventually
which device gave us the read error. For RAID10, mirror_num must be 1 or 2.
Before this fix mirror_num was incorrectly related to our stripe index.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_start_delalloc_inodes will just walk the list of delalloc inodes and
start writing them out, but it doesn't splice the list or anything so as
long as somebody is doing work on the box you could end up in this section
_forever_. So just remove it, it's not needed anyway since sync will start
writeback on all inodes anyway, all we need to do is wait for ordered
extents and then we can commit the transaction. In my horrible torture test
sync goes from taking 4 minutes to about 1.5 minutes. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
We were not properly advertising the MODE bits supported by this driver, fix
that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We do not need to use a flag to indicate if the master driver is stopping
it is sufficient to perform spi master unregistering in the platform
driver's remove function.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch converts the bcm63xx SPI driver to use the SPI infrastructure
pump message queue. Since we were previously sleeping in the SPI
driver's transfer() function (which is not allowed) this is now fixed as well.
To complete that conversion a certain number of changes have been made:
- the transfer len is split into multiple hardware transfers in case its
size is bigger than the hardware FIFO size
- the FIFO refill is no longer done in the interrupt context, which was a
bad idea leading to quick interrupt handler re-entrancy
Tested-by: Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Bug noticed in commit
bf118a342f
When calling GETACL, if the size of the bitmap array, the length
attribute and the acl returned by the server is greater than the
allocated buffer(args.acl_len), we can Oops with a General Protection
fault at _copy_from_pages() when we attempt to read past the pages
allocated.
This patch allocates an extra PAGE for the bitmap and checks to see that
the bitmap + attribute_length + ACLs don't exceed the buffer space
allocated to it.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reported-by: Jian Li <jiali@redhat.com>
[Trond: Fixed a size_t vs unsigned int printk() warning]
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
A new enum indicating the dma channel direction was introduced by:
commit 49920bc669
dmaengine: add new enum dma_transfer_direction
The following commit changed spi-ep93xx to use the new enum:
commit a485df4b44
spi, serial: move to dma_transfer_direction
In doing so a sparse warning was introduced:
warning: mixing different enum types
int enum dma_data_direction versus
int enum dma_transfer_direction
This is produced because the 'dir' passed in ep93xx_spi_dma_prepare
is an enum dma_data_direction and is being used to set the
dma_slave_config 'direction' which is now an enum dma_transfer_direction.
Fix this by converting spi-ep93xx to use the new enum type in all
places.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix kernel-doc warning in spi.h (copy/paste):
Warning(include/linux/spi/spi.h:365): No description found for parameter 'unprepare_transfer_hardware'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
calculate_effective_freq() was still not optimized and there were cases when it
returned without error and with values of cpsr and scr as zero.
Also, the variable named found is not used well.
This patch targets to optimize and correct this routine. Tested for SPEAr.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'v3.4-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: add missing MMC_CAP2_BROKEN_VOLTAGE capability
ARM: EXYNOS: Fix compilation error when CONFIG_OF is not defined
ARM: EXYNOS: Fix resource on dev-dwmci.c
ARM: S3C24XX: Fix build warning for S3C2410_PM
ARM: mini2440_defconfig: Fix build error
ARM: EXYNOS: Fix incorrect initialization of GIC
ARM: EXYNOS: use 'exynos4-sdhci' as device name for sdhci controllers
Clean up a reference to jiffies in tcp_rcv_rtt_measure() that should
instead reference tcp_time_stamp. Since the result of the subtraction
is passed into a function taking u32, this should not change any
behavior (and indeed the generated assembly does not change on
x86_64). However, it seems worth cleaning this up for consistency and
clarity (and perhaps to avoid bugs if this is copied and pasted
somewhere else).
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few more fixes for v3.4-rc cycle.
It includes a couple of fixes to the ordering of the methods in udc-core.c.
Without these two patches, we will have issues when either unregistering a
gadget driver (triggered with dummy_hcd only) or issuing a device-initiated
disconnect through sysfs.
There's also a fix on dummy_hcd to not call ->pullup() from udc_stop() because
udc-core.c already handles that.
A fix to MUSB as promised, to kill the compile warnings regarding deprecated
interfaces. We are essentially dropping the __deprecated flag because it
doesn't look like we will ever be able to live without it when we consider the
amount of silicon issues we find on different MUSB instantiations.
A couple of other fixes are also available, one adding the missing transceiver
events to gpio_vbus and another adding a missing unregister call to MUSB's
davinci glue layer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJPmlT8AAoJEIaOsuA1yqREGD4P/i8H8Pt46V6PekeV7G/8z3O/
F317Y7xDo1P5DVpfLkzB4xjAEtlu2MhH8mhf2bNbWN3kCFBh13Nm/rarIMYS+H/Z
qGdou47LyUh65BUyGp7Ul66KPtGaA5hTuTag/DdyvfJeR0ePZgzZ8gpcGm4Cn/zR
LqLDB3D+qa8W2TUyibNjNHC/An9PSvEQcCkmdIAhOaQkBoRnqgtfoD6ecN5gCebQ
UOSr6q9Xh97QRoMEsQ4xAEeKBh6RnB30suhDzbO0ISJ9kmQWK9TX8DdxZvMSAkCk
HHmOUXtivlznNqk7+ckpl7tcwhnVKiYcXjvcS7MpSU+FHXNYcs4EqxFR/CWcBuiO
nQcn8pFZ6+Bw07myQlPZtjJTEPkPcn6pq0iMWSR6W/EWIsfe9AFa4YiouiyuqsCf
yCFVJc/VzoSHkYWEy/S7loFOXLhBvU0S6okR5yjg0GrW386aIzDmPHCPU6JcJrOg
NAcAdWWrN+rCeqz/f7Lkp69ni8CNsuvN3bCLvQuit4e+9oM8EabIkrd6Akc2+d8j
IIDiz2MwtOXkoRyJ8ua6P3ilIhfp16R/mQVA4uGe8WzF8pMzctNSzQSmzTyBEkHc
YM7a7pcAwkQk6CXdpbH3fi++dwAjR7fZufODSLau/w1YJpSBFWg/ByzIfVWvMFrW
KcESapF9TybpiqjPMzeX
=Epei
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
usb: fixes for v3.4-rc cycle
A few more fixes for v3.4-rc cycle.
It includes a couple of fixes to the ordering of the methods in udc-core.c.
Without these two patches, we will have issues when either unregistering a
gadget driver (triggered with dummy_hcd only) or issuing a device-initiated
disconnect through sysfs.
There's also a fix on dummy_hcd to not call ->pullup() from udc_stop() because
udc-core.c already handles that.
A fix to MUSB as promised, to kill the compile warnings regarding deprecated
interfaces. We are essentially dropping the __deprecated flag because it
doesn't look like we will ever be able to live without it when we consider the
amount of silicon issues we find on different MUSB instantiations.
A couple of other fixes are also available, one adding the missing transceiver
events to gpio_vbus and another adding a missing unregister call to MUSB's
davinci glue layer.
The current code puts the built-in WMAC device of the
AR933X SoCs into reset instead of starting it. This
causes a hard lock on AR933X based boards when the
wireless driver tries to access the device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3484/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since the last fixes to this driver ensure now the queue termination is
done correctly, we can finally disable the queue after a transfer
without problems. The gain is that it will only be reenabled after the
next transfer is fully set up. Before, the queue was running all the
time and if the setup of the next message was interrupted by another
thread, an incomplete buffer could have been sent, padded with zeroes.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch (as1548) fixes a recently-introduced incompatibility
between the UDC core and the dummy-hcd driver. Commit
8ae8090c82 (usb: gadget: udc-core: fix
asymmetric calls in remove_driver) moved the usb_gadget_udc_stop()
call in usb_gadget_remove_driver() below the usb_gadget_disconnect()
call.
As a result, usb_gadget_disconnect() gets called at a time when the
gadget driver believes it has been unbound but dummy-hcd believes
it has not. A nasty error ensues when dummy-hcd calls the gadget
driver's disconnect method a second time.
To fix the problem, this patch moves the gadget driver's unbind
notification after the usb_gadget_disconnect() call. Now nothing
happens between the two unbind notifications, so nothing goes wrong.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 6d258a4 (usb: gadget: udc-core: stop UDC on device-initiated
disconnect) introduced another case of asymmetric calls when issuing
a device-initiated disconnect. Fix it.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
An entry for INTERNAL_VCE encoder was missing. Add it.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From Daniel Vetter
- VGA load-detect fix. This bug seems to be as old as the load-detect code
(2.6.30), but needs stupid userspace (upowerd trying to detect
connectors on dpms-off outputs) to actually kill the machine. And
obviously a machine without VGA-hotplug, otherwise we don't do load
detect.
- 2 interger overflow fixes for unpriviledged ioctls from Xi Wang.
- Fix SDVO regression for low-res (pixelclock < 100MHz) digital outputs,
introduce in 2.6.36.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: handle input/output sdvo timings separately in mode_set
drm/i915: fix integer overflow in i915_gem_do_execbuffer()
drm/i915: fix integer overflow in i915_gem_execbuffer2()
drm/i915: fixup load-detect on enabled, but not active pipe
From Inki Dae:
this patch set fixes gem allocation and mapping issue between user space and
physical memory region.
* 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-2.6-samsung:
drm/exynos: added missed vm area region mapping type.
drm/exynos: fixed exynos_drm_gem_map_pages bug.
drm/exynos: fixed duplicatd memory allocation bug.
Pins configured as input and have MFP_LPM_DRIVE_* flag set, can have a
wrong output value for some period of time (spike) during the suspend
sequence.
This can happen because the direction of the pins (GPDR) is set by
software and the output level is set by hardware (PGSR) at a later
stage.
Fix the above potential bug by setting the output levels first.
Also save the actual levels of the pins before the suspend and restore
them after the resume, but before the direction settings take place, so
the same bug as described above will not happen in the resume sequence.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Pins that have MFP_LPM_KEEP_OUTPUT set and are configured for output
must retain the output state in low power mode.
Currently, the pin direction configuration is overrided with values
in gpdr_lpm[] array and do not obey the MFP_LPM_KEEP_OUTPUT setting.
Fix the above bug and add some documentation to clarify the
MFP_LPM_KEEP_OUTPUT setting purpose.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
DEFINE_RES_MEM() takes the size of resource as a second argument,
not the end address. Passing end address leads to following error
in runtime during device registration:
sa1100-rtc: failed to claim resource 0
Fix it.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
In 3.3, gpio wakeup setting was broken. The call
enable_irq_wake() didn't set up the PXA gpio registers
(PWER, ...) anymore.
Fix it at least for pxa27x. The driver doesn't seem to be
used in pxa25x (weird ...), and the fix doesn't extend to
pxa3xx and pxa95x (which don't have a gpio_set_wake()
available).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
We did a similar check for the P-states but did not do it for
the C-states. What we want to do is ignore cases where the DSDT
has definition for sixteen CPUs, but the machine only has eight
CPUs and we get:
xen-acpi-processor: (CX): Hypervisor error (-22) for ACPI CPU14
Reported-by: Tobias Geiger <tobias.geiger@vido.info>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When we boot on a machine that can hotplug CPUs and we
are using 'dom0_max_vcpus=X' on the Xen hypervisor line
to clip the amount of CPUs available to the initial domain,
we get this:
(XEN) Command line: com1=115200,8n1 dom0_mem=8G noreboot dom0_max_vcpus=8 sync_console mce_verbosity=verbose console=com1,vga loglvl=all guest_loglvl=all
.. snip..
DMI: Intel Corporation S2600CP/S2600CP, BIOS SE5C600.86B.99.99.x032.072520111118 07/25/2011
.. snip.
SMP: Allowing 64 CPUs, 32 hotplug CPUs
installing Xen timer for CPU 7
cpu 7 spinlock event irq 361
NMI watchdog: disabled (cpu7): hardware events not enabled
Brought up 8 CPUs
.. snip..
[acpi processor finds the CPUs are not initialized and starts calling
arch_register_cpu, which creates /sys/devices/system/cpu/cpu8/online]
CPU 8 got hotplugged
CPU 9 got hotplugged
CPU 10 got hotplugged
.. snip..
initcall 1_acpi_battery_init_async+0x0/0x1b returned 0 after 406 usecs
calling erst_init+0x0/0x2bb @ 1
[and the scheduler sticks newly started tasks on the new CPUs, but
said CPUs cannot be initialized b/c the hypervisor has limited the
amount of vCPUS to 8 - as per the dom0_max_vcpus=8 flag.
The spinlock tries to kick the other CPU, but the structure for that
is not initialized and we crash.]
BUG: unable to handle kernel paging request at fffffffffffffed8
IP: [<ffffffff81035289>] xen_spin_lock+0x29/0x60
PGD 180d067 PUD 180e067 PMD 0
Oops: 0002 [#1] SMP
CPU 7
Modules linked in:
Pid: 1, comm: swapper/0 Not tainted 3.4.0-rc2upstream-00001-gf5154e8 #1 Intel Corporation S2600CP/S2600CP
RIP: e030:[<ffffffff81035289>] [<ffffffff81035289>] xen_spin_lock+0x29/0x60
RSP: e02b:ffff8801fb9b3a70 EFLAGS: 00010282
With this patch, we cap the amount of vCPUS that the initial domain
can run, to exactly what dom0_max_vcpus=X has specified.
In the future, if there is a hypercall that will allow a running
domain to expand past its initial set of vCPUS, this patch should
be re-evaluated.
CC: stable@kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
With the introduction of static keys, anything using tracepoints blows up
in the following manner:
include/trace/events/oom.h:8:13: error: initializer element is not constant
include/trace/events/oom.h:8:13: error: (near initialization for '__tracepoint_oom_score_adj_update')
include/trace/events/oom.h:8:13: error: initializer element is not constant
include/trace/events/oom.h:8:13: error: (near initialization for '__tracepoint_oom_score_adj_update.key')
This is a result of the STATIC_KEY_INIT_xxx defs wrapping ATOMIC_INIT()
which on sh includes an atomic_t typecast. Given that we don't really
need the typecast for anything anymore, the simplest solution is simply
to kill off the cast.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes a race whereby a pointer to a buffer
would be overwritten while the buffer was in use leading
to a double free and a memory leak. This causes crashes.
This bug was introduced in 2.6.34
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As described in e6fa16ab ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block
is pending in the shared queue.
Also, use the new helper function introduced in commit 5e6292c0f2
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures. In the past some architectures got this
code wrong, so using this helper function should stop that from
happening again.
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/3363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull arch/tile fixes from Chris Metcalf:
"One change fixes a platform-independent bug about environment var
handling in the boot command line. The other is a trivial
tile-specific bug fix to avoid a link-time warning."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: fix a couple of functions that should be __init
init: fix bug where environment vars can't be passed via boot args
- fix memory leak in mlx4
- fix two problems with new MAD response generation code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=iRrT
-----END PGP SIGNATURE-----
Merge tag 'ib-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"A few fixes for regressions introduced in 3.4-rc1:
- fix memory leak in mlx4
- fix two problems with new MAD response generation code"
* tag 'ib-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Fix memory leaks in ib_link_query_port()
IB/mad: Don't send response for failed MADs
IB/mad: Set 'D' bit in response for unhandled MADs
Commit e520c41085
"xtensa: convert to asm-generic/hardirq.h"
converted over to using the asm-generic parts, but it also
added the sentinel
#define ack_bad_irq ack_bad_irq
which tells asm-generic to _not_ use the common ack_bad_irq.
Since e520c41 deleted the duplicated code from the arch specific
file, we _do_ want the asm-generic one in scope. So delete
the trigger define above which hides it. In doing so we'll
realize that we've got to delete the almost-duplicate prototype
as well to avoid "static declaration ... follows non-static".
Cc: Christoph Hellwig <hch@lst.de>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
A workaround for an ASUS laptop and a few ASoC changes;
most of the commits are tagged for stable, too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=KjOE
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A workaround for an ASUS laptop and a few ASoC changes; most of the
commits are tagged for stable, too."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8994: Improve sequencing of AIF channel enables
ALSA: HDA: Add external mic quirk for Asus Zenbook UX31E
ASoC: fsi: update for dmaengine prep_slave_sg fallout.
ASoC: core: Fix card RTD count for deferred probe.
ASoC: cs42l73: don't use negative array index
ASoC: dapm: Ensure power gets managed for line widgets
Pull a watchdog fix from Wim Van Sebroeck:
"It will fix the size when reading or writing to WD Timer port 0x72 in
the hpwdt driver."
* git://www.linux-watchdog.org/linux-watchdog:
hpwdt: Only BYTE reads/writes to WD Timer port 0x72
Pull timer fixes from Thomas Gleixner.
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Fix the spurious broadcast timer ticks after resume
tick: Ensure that the broadcast device is initialized
tick: Fix oneshot broadcast setup really
Merge fixes from Andrew Morton:
"13 fixes. The acerhdf patches aren't (really) fixes. But they've
been stuck in my tree for up to two years, sent to Matthew multiple
times and the developers are unhappy."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (13 patches)
mm: fix NULL ptr dereference in move_pages
mm: fix NULL ptr dereference in migrate_pages
revert "proc: clear_refs: do not clear reserved pages"
drivers/rtc/rtc-ds1307.c: fix BUG shown with lock debugging enabled
arch/arm/mach-ux500/mbox-db5500.c: world-writable sysfs fifo file
hugetlbfs: lockdep annotate root inode properly
acerhdf: lowered default temp fanon/fanoff values
acerhdf: add support for new hardware
acerhdf: add support for Aspire 1410 BIOS v1.3314
fs/buffer.c: remove BUG() in possible but rare condition
mm: fix up the vmscan stat in vmstat
epoll: clear the tfile_check_list on -ELOOP
mm/hugetlb: fix warning in alloc_huge_page/dequeue_huge_page_vma
In pirq_check_eoi_map use the pirq number rather than the Linux irq
number to check whether an eoi is needed in the pirq_eoi_map.
The reason is that the irq number is not always identical to the
pirq number so if we wrongly use the irq number to check the
pirq_eoi_map we are going to check for the wrong pirq to EOI.
As a consequence some interrupts might not be EOI'ed by the
guest correctly.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-by: Tobias Geiger <tobias.geiger@vido.info>
[v1: Added some extra wording to git commit]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
There are exactly four users of __monitor and __mwait:
- cstate.c (which allows acpi_processor_ffh_cstate_enter to be called
when the cpuidle API drivers are used. However patch
"cpuidle: replace xen access to x86 pm_idle and default_idle"
provides a mechanism to disable the cpuidle and use safe_halt.
- smpboot (which allows mwait_play_dead to be called). However
safe_halt is always used so we skip that.
- intel_idle (same deal as above).
- acpi_pad.c. This the one that we do not want to run as we
will hit the below crash.
Why do we want to expose MWAIT_LEAF in the first place?
We want it for the xen-acpi-processor driver - which uploads
C-states to the hypervisor. If MWAIT_LEAF is set, the cstate.c
sets the proper address in the C-states so that the hypervisor
can benefit from using the MWAIT functionality. And that is
the sole reason for using it.
Without this patch, if a module performs mwait or monitor we
get this:
invalid opcode: 0000 [#1] SMP
CPU 2
.. snip..
Pid: 5036, comm: insmod Tainted: G O 3.4.0-rc2upstream-dirty #2 Intel Corporation S2600CP/S2600CP
RIP: e030:[<ffffffffa000a017>] [<ffffffffa000a017>] mwait_check_init+0x17/0x1000 [mwait_check]
RSP: e02b:ffff8801c298bf18 EFLAGS: 00010282
RAX: ffff8801c298a010 RBX: ffffffffa03b2000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff8801c29800d8 RDI: ffff8801ff097200
RBP: ffff8801c298bf18 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000000
R13: ffffffffa000a000 R14: 0000005148db7294 R15: 0000000000000003
FS: 00007fbb364f2700(0000) GS:ffff8801ff08c000(0000) knlGS:0000000000000000
CS: e033 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 000000000179f038 CR3: 00000001c9469000 CR4: 0000000000002660
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process insmod (pid: 5036, threadinfo ffff8801c298a000, task ffff8801c29cd7e0)
Stack:
ffff8801c298bf48 ffffffff81002124 ffffffffa03b2000 00000000000081fd
000000000178f010 000000000178f030 ffff8801c298bf78 ffffffff810c41e6
00007fff3fb30db9 00007fff3fb30db9 00000000000081fd 0000000000010000
Call Trace:
[<ffffffff81002124>] do_one_initcall+0x124/0x170
[<ffffffff810c41e6>] sys_init_module+0xc6/0x220
[<ffffffff815b15b9>] system_call_fastpath+0x16/0x1b
Code: <0f> 01 c8 31 c0 0f 01 c9 c9 c3 00 00 00 00 00 00 00 00 00 00 00 00
RIP [<ffffffffa000a017>] mwait_check_init+0x17/0x1000 [mwait_check]
RSP <ffff8801c298bf18>
---[ end trace 16582fc8a3d1e29a ]---
Kernel panic - not syncing: Fatal exception
With this module (which is what acpi_pad.c would hit):
MODULE_AUTHOR("Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>");
MODULE_DESCRIPTION("mwait_check_and_back");
MODULE_LICENSE("GPL");
MODULE_VERSION();
static int __init mwait_check_init(void)
{
__monitor((void *)¤t_thread_info()->flags, 0, 0);
__mwait(0, 0);
return 0;
}
static void __exit mwait_check_exit(void)
{
}
module_init(mwait_check_init);
module_exit(mwait_check_exit);
Reported-by: Liu, Jinsong <jinsong.liu@intel.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This file has lots and lots of ifdef, around structure decls
and structure usages. The failure issue was that we would
build the BF538-EZKIT_defconfig and get:
arch/blackfin/mach-bf538/boards/ezkit.c:924:3: error: 'bfin_lq035q1_device'
undeclared here (not in a function)
even though the same ifdef _appeared_ to enable both the struct
declaration and the code that used it. Yet cpp was telling us we
didn't have the struct, but we still had the usage of it.
However, _appeared_ is the operative word. After marking all the
anonymous #endif with their parent #ifdef config options, it was
_then_ clear that there was a misplaced #endif that was hiding
the struct declaration.
The real guts of the patch boils down to this:
-#endif
+#endif /* CONFIG_MTD_M25P80 */
+#endif /* CONFIG_SPI_BFIN5XX */
[...]
-#endif /* spi master and devices */
but since I had to tag the #endif with their respective #ifdef
options to find this misplaced SPI endif, it would be silly to
then go and delete them all. So they stay.
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: Bob Liu <lliubbo@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
