Signed-off-by: John Li <chen-yang.li@mediatek.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was introduced by commit
77b5621bac (rt2x00: Don't use queue entry
as parameter when creating TX descriptor.)
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions that create the tx descriptor structure do not operate on
a queue entry at all. Signal this fact in the code by not providing a
queue entry as a parameter, but the rt2x00 device structure and the skb
directly.
This patch is a preparation for reducing the time a queue is locked for
a tx operation.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The two functions that are in rt2x00ht.c can be much better placed
closer to the places where the call-sites of these functions are (one
in rt2x00config.c and one in rt2x00queue.c) allowing us to make these
functions static.
Also, conditional compilations doesn't seem to be necessary anymore as
802.11n support is quite common nowadays.
This makes the code a bit easier readable and searchable.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a timestamp to each queue entry which is updated whenever
the status of the entry changes, and remove the per-queue
timestamps. The previous check was incorrect and caused both
false positives and false negatives.
With the corrected check it comes apparent that the TX status
usually times out on rt2800usb unless there is sufficient traffic
(i.e. the next TX will complete the previous TX status).
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of flags defined for the rt2x00dev->flags field,
has been growing over the years. Currently we are approaching
the maximum number of bits which are available in the field.
A secondary problem, is that one part of the field are initialized only
during boot, because the driver requirements are initialized or device
requirements are loaded from the EEPROM. In both cases, the flags are
fixed and will not change during device operation. The other flags are
the device state, and will change frequently. So far this resulted in the fact
that for some flags, the atomic bit accessors are used, while for the others
the non-atomic variants are used.
By splitting the flags up into a "flags" and "cap_flags" we can put all flags
which are fixed inside "cap_flags". This field can then be read non-atomically.
In the "flags" field we keep the device state, which is going to be read atomically.
This adds more room for more flags in the future, and sanitizes the field access methods.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800 devices should adjust their tx power in accordance with the
eeproms temperature calibration values. Add a new driver callback
gain_calibration that is called every 4 seconds.
The rt2800 gain calibration routine simply runs the tx power
configuration that takes care of calculating the temperature
compensation delta.
We don't need to synchronize the calls to rt2800_config_txpower
as they should all happen from mac80211's single threaded workqueue.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit d1c3a37cee ("mac80211:
clarify alignment docs, fix up alignment") removed the requirement
for a 4-byte aligned payload rt2x00queue_align_payload is obsolete
as mac80211 will align the payload when it passes the frame to the
net stack.
As a result we can remove the call to rt2x00queue_align_payload in the
rx path and since that's the last user we can remove
rt2x00queue_align_payload altogether.
One advantage is that we save some alignment operations for frames
that don't need to be aligned (for example beause they are not passed
to the net stack).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a beacon_update_locked function that does not acquire the
according beacon mutex to allow beacon updates from atomic context. The
caller has to take care of synchronization.
No functional changes. Just preparation for beacon updates from tasklet
context.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows to dynamically remove beaconing interfaces without
shutting beaconing down on all interfaces.
The only place to start and stop beaconing are now the start- and
stop_queue callbacks. Hence, we can remove some register writes during
interface bring up (config_intf) and only write the correct sync mode
to the register there.
When multiple beaconing interfaces are present we should enable
beaconing as soon as mac80211 enables beaconing on at least one of
them. The beacon queue gets stopped when the last beaconing
interface was stopped by mac80211. Therefore, introduce another
interface counter to keep track ot the number of enabled beaconing
interfaces and start or stop the beacon queue accordingly.
To allow single interfaces to stop beaconing, add a new driver
callback clear_beacon to clear a single interface's beacon without
affecting the other interfaces. Don't overload the clear_entry callback
for clearing beacons as that would introduce additional overhead
(check for each TX queue) into the clear_entry callback which is used
on the drivers TX/RX hotpaths.
Furthermore, the write beacon callback doesn't need to enable beaconing
anymore but since beaconing should be disabled while a new beacon is
written or cleared we still disable beacon generation and enable it
afterwards again in the driver specific callbacks. However, beacon
related interrupts should not be disabled/enabled here, that's solely
done from the start- and stop queue callbacks. It would be nice to stop
the beacon queue just before the beacon update and enable it afterwards
in rt2x00queue itself instead of the current implementation that relies
on the driver doing the right thing. However, since start- and
stop_queue are mutex protected we cannot use them for atomic beacon
updates.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add wrapper functions in rt2x00queue.c to
start & stop queues. This control must be protected
using a mutex.
Queues can also be paused which will halt the flow
of packets between the driver and mac80211. This doesn't
require a mutex protection.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the queue refactoring, the rt2x00lib_toggle_rx
can be removed and replaced with the call directly to
the set_device_state callback function.
We can remove the STATE_RADIO_RX_ON_LINK and
STATE_RADIO_RX_OFF_LINK, as it was only used for
special behavior inside rt2x00lib rather then the
drivers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00lib.h:60: ERROR: space prohibited after that open parenthesis '('
rt2x00lib.h:60: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A lot of functions accept a struct rt2x00_dev combined with
either a struct queue_entry or struct data_queue argument.
This can be simplified by only passing on the queue/entry
argument.
In cases where rt2x00_dev and a sk_buff are send together,
we can send the queue_entry instead.
rt2x00usb_alloc_urb and rt2x00usb_free_urb have a bit
of vague naming. Instead they allocate all the data which
belongs to a rt2x00 data queue entry.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously rt2x00 was always updating all erp related config variables
even though mac80211 might only have changed one. Hence, pass the
changed flags to the config_erp driver callback so that the driver
can limit the changes to the correct values.
This fixes an issue in AP mode where the beacon interval is not
initialized (and thus zero) but still sent to the hardware causing an
interrupt storm on rt2800pci hanging the system.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement watchdog monitoring for USB devices (PCI support can
be added later). This will determine if URBs being uploaded to
the hardware are actually returning. Both rt2500usb and rt2800usb
have shown that URBs being uploaded can remain hanging without
being released by the hardware.
By using this watchdog, a queue can be reset when this occurs.
For rt2800usb it has been tested that the connection is preserved
even though this interruption.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Closer inspection of the legacy Ralink driver reveals that in case of HT40+
or HT40- we must adjust the frequency settings that we program to the device.
Implement the same adjustment in the rt2x00 code.
With this HT40 seems to work for all devices supported by rt2800pci and
rt2800usb.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Instead of fiddling with the skb->data pointer and thereby risking
out of bounds accesses, properly reserve the space needed in an
skb for descriptors.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
This allows rt2x00debug_dump_frame to be used from everywhere.
This is preparation for beacon writing clean ups.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Right now all frames mac80211 hands to the driver
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set to
request TX status. This isn't really necessary, only
the injected frames need TX status (the latter for
hostapd) so move setting this flag.
The rate control algorithms also need TX status, but
they don't require it.
Also, rt2x00 uses that bit for its own purposes and
seems to require it being set for all frames, but
that can be fixed in rt2x00.
This doesn't really change anything for any drivers
but in the future drivers using hw-rate control may
opt to not report TX status for frames that don't
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com> [rt2x00 bits]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As mentioned on the linux-wireless mailing list, the current copyright
statements in the rt2x00 are meaningless, as the rt2x00 project is
not even a formal legal entity. Therefore it is better to replace
the existing copyright statements with copyright statements for the
people that actually wrote the code.
Note: Updated to the best of my knowledge with respect to who
contributed considerable amounts of code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_rx_status->qual has been marked deprecated.
This allows us to remove several functions and fields which
were used to calculate a reasonable value for it.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the redundant l2pad parameter from the definition of
rt2x00crypto_rx_insert_iv which is used when only CONFIG_RT2500PCI but
none of the other rt2x00 family drivers is configured.
Signed-off-by: Andrew Price <andy@andrewprice.me.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old function rt2x00queue_payload_align() handled
both adding and removing L2 padding and some basic
frame alignment. The entire function was being abused
because it had multiple functions and the header length
argument was somtimes used to align the header instead
of the payload.
Additionally there was a bug when inserting L2 padding
that only the payload was aligned but not the header. This
happens when the header wasn't aligned properly by mac80211,
but rt2x00lib only moves the payload.
A secondary problem was that when removing L2 padding during
TXdone or RX the skb wasn't resized to the proper size.
Split the function into seperate functions each handling
its task as it should.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00dev->default_ant should be initialized once by the driver,
and should not be changed afterwards. Because rt2x00lib_config_antenna()
was using a reference to the struct antenna_setup it actually had the oppurtunity
to change the default antenna setting and it actually did that during the validation.
Instead of passing a pointer to antenna_setup the entire structure should be copied.
Signed-off-by: Lars Ericsson <Lars_Ericsson@telia.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the input_polldev from rt2x00 and replace it with
the rfkill interface offered by the wiphy structure. This
simplifies the entire rfkill handling in rt2x00 and allows
us to remove the CONFIG_RT2X00_LIB_RFKILL option and always
enables rfkill capabilities.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extra parenthesis are not needed in these 2 cases,
all other defines in rt2x00 are done without parenthesis
so just fixup these 2 cases.
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend rt2x00lib capabilities to support 802.11n,
it still lacks aggregation support, but that can
be added in the future.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware require L2 padding between header and payload
because both must be aligned to a 4-byte boundary. This hardware
also is easier during the RX path since we no longer need to
move the entire payload but rather only the header to remove
the padding (mac80211 only wants the payload to be 4-byte aligned).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By placing the iv_len into the tx descriptor data and
by passing this data to the crypto IV handlers we can
save multiple calls to ieee80211_get_hdrlen_from_skb()
and some if-statements when copying/removing the IV data
from the outgoing frame.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
provide rt2x00lib the possibility to kill a particular TX queue.
This can be useful when disabling the radio, but more importantly
will allow beaconing to be disabled when mac80211 requests this
(during scanning for example)
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Then one place can be a static const.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As discussed on linux-wireless rt2x00 does not offer a true RFKILL key,
for that reason RFKILL support should be entirely removed.
The key which is attached to the hardware should be treated as normal
input device instead. Implement input_poll_dev support to poll the device
frequently. When the key status has changed report it as a SW event.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some functions have grown rapidly in size over the last time,
some of those functions (like the rt2x00queue_create_tx_descriptor)
will further increase in size soon, so it is best to start cutting
it into logical pieces.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move link and antenna tuning into a seperate file named rt2x00link.c,
this makes the interface to the link tuner a lot cleaner.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The short preamble mode was not correctly detected during TX,
rt2x00 used the rate->hw_value_short field but mac80211 is not
using this field that way.
Instead the flag IEEE80211_TX_RC_USE_SHORT_PREAMBLE should be
used to determine if the frame should be send out using
short preamble or not.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all code which determines the right TX descriptor
fields specific to crypto support into rt2x00crypto.c.
This makes the code in rt2x00queue more simpler and
better concentrates all crypto code into a single location.
With this we can also remove some ifdefs in rt2x00queue.c
since the code inside the ifdef is either very small, or
only calling empty functions (see empty function definitions
in rt2x00lib.h).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2500usb supports hardware encryption.
rt2500usb supports up to 4 shared and pairwise keys.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge the callback functions init_txentry() and
init_rxentry(). This makes life in rt2x00lib a
lot simpler and we can cleanup several functions.
rt2x00pci contained "fake" FIELD definitions for
descriptor words. This is not flexible since it
assumes the driver will always have the same field
to indicate if a driver is available or not.
This should be dependent on the driver, and we
should add a callback function for this.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new configuration handling, and more specifically
splitting the configuration of the antenna from the normal
configuration steps allowed a BUG_ON() to be triggered
in the driver because the SW_DIVERSITY was send to the
driver. This fixes that by catching the value early in
rt2x00config.c and replacing it with a sensible value.
This also fixes a problem where the antenna is not being
initialized at all when the radio is enabled. Since it
no longer is part of the mac80211 configuration the
only place where rt2x00 configured it was the SW diversity
handler. Obviously this is broken for all non-diversity
hardware and breaks SW diversity due to a broken initialization.
When the radio is enabled the antenna will be configured
once as soon as the config() callback function is called.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 is in charge of determining the basic rates,
so we are not using the RATE_BASIC flag anymore.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement latest changed from mac80211 configuration
handling to optmize configuration handling in rt2x00.
* Remove set_retry_limit callback function, handled
through config()
* Move config_antenna to its own callback function,
it isn't handled by mac80211 anymore
* Use IEEE80211_CONF_CHANGED_* flags and remove manual
checks
* Removed deprecated short slot setting through config()
and put it in config_erp() through which mac80211 now
configures it
* Remove config_phymode() and move contents to config_erp()
since it only managed the basic rates which is now
determined by mac80211 through config_erp().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's really no reason for mac80211 to be using its
own interface type defines. Use the nl80211 types and
simplify the configuration code a bit: there's no need
to translate them any more now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various rt2x00 devices support hardware encryption.
Most of them require the IV/EIV to be generated by mac80211,
but require it to be provided seperately instead of within
the frame itself. This means that rt2x00lib should extract
the data from the frame and place it in the frame descriptor.
During RX the IV/EIV is provided in the descriptor by the
hardware which means that it should be inserted into the
frame by rt2x00lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new beacon handling from mac80211 we can
reorganize the beacon handling in rt2x00 as well.
This patch will move the function to the TX handlers,
and move all duplicate code into rt2x00queue.c.
After this change the descriptor helper functions
from rt2x00queue.c no longer need to be exported
outside of rt2x00lib and can be declared static.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new rfkill interface there is no longer a need
for the input_polldev. Create a delayed_work structure
which we can put on the mac80211 workqueue and poll the
hardware every 1000ms.
v2: Decrease poll frequency from 100ms to 1000ms
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
