After 9de5d235b6 ("net: phy: fix aneg restart in phy_ethtool_set_eee")
we don't need the check for aneg being enabled any longer, and as
discussed with Russell configuring the EEE advertisement should be
supported even if we're in a half-duplex mode currently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync the reset preparation for chips from RTL8168g with the r8168 and
r8125 vendor drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a helper for waiting for FIFO's to be empty, again the name is
borrowed from the vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a helper for setting RXDV_GATED_EN, the 2ms delay is copied from
the vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create a helper for this waiting function, name of the helper is
borrowed from the vendor driver. In addition don't return in the two
hw_init functions if the first wait runs into a timeout, there's no
benefit in doing so.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
r8169 never had native support for the RTL8401, however it reportedly
worked with the fallback to RTL8101e [0]. Therefore let's add this
as an explicit assignment.
[0] https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=956868
Fixes: b4cc2dcc9c ("r8169: remove default chip versions")
Reported-by: Camaleón <noelamac@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use new flexible sleep function fsleep() to merge the udelay and msleep
polling functions. We can safely do this because no polling function
is used in atomic context in this driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper eth_hw_addr_crc to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Considering the few messages we have in the driver, there's not really
a benefit in being able to control them on a message type level.
Therefore simplify the code and switch to the netdev_xxx message
functions. In addition add net_ratelimit() to messages that can be
printed from a hot path.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When preparing an unrelated change, checkpatch complained about this
redundant out-of-memory message. Therefore remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The counter handling functions can only fail if rtl8169_do_counters()
times out. In the poll function we emit an error message in case of
timeout, therefore we don't have to propagate the timeout all the
way up just to print another message basically saying the same.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Net core - __dev_set_promiscuity - prints a message already when
promiscuous mode in entered/left, therefore we don't have to do this
in the driver too. Also the driver message would be misleading
(would be because "link" message level is disabled per default)
because it would print "promisc mode enabled" even if it's being
left. Reason is that __dev_change_flags() calls dev_set_rx_mode()
before touching the promisc flag.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a not needed parameter in rtl8169_set_magic_reg.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8125 supports the same PME_SIGNAL handling as all later RTL8168
chip variants.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync definition of max jumbo packet size with vendor driver and reserve
22 bytes for VLAN ethernet header plus checksum.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek provided information about a HW constraint that time limit must
not be set to 0 if the frame limit is >0. Add a check for this and
reject invalid parameter combinations.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use FIELD_PREP() to make the code better readable, and avoid the loop.
No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip supports only frame limits 0, 4, 8, .. 60 internally.
Returning EINVAL for all val % 4 != 0 seems to be a little bit too
unfriendly to the user. Therefore round up the frame limit to the next
supported value. In addition round up the time limit, else a very low
limit could be rounded down to 0, and interpreted as "ignore value"
by the chip.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The time limit provided by userspace is multiplied with 1000,
what could result in an overflow. Therefore change the time limit
parameter unit from ns to us, and avoid the problematic operation.
If there's no matching scale because provided time limit is too big,
return ERANGE instead of EINVAL to provide a hint to the user what's
wrong.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use FIELD_GET() macro to make the code better readable. In addition
change the logic to round the time limit up, not down. Reason is that
a time limit <1us would be rounded to 0 currently, what would be
interpreted as "no time limit set".
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx and tx scale are the same always. Simplify the code by using one
scale for rx and tx only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net_device argument is just used to get a struct rtl8169_private
pointer via netdev_priv(). Therefore pass the struct rtl8169_private
pointer directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a number of consumer mainboards where the BIOS leaves the PHY
in a state that it's reporting an invalid PHY ID. To detect such cases
add the PHY ID to the error message if no dedicated PHY driver is found.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two bits in RxConfig are controlled by the following dev->feature's:
- NETIF_F_RXALL
- NETIF_F_HW_VLAN_CTAG_RX (since RTL8125)
We have to take care that RxConfig gets fully configured in
rtl_hw_start() after e.g. resume from hibernation. Therefore:
- Factor out setting the feature-controlled RxConfig bits to a new
function rtl_set_rx_config_features() that is called from
rtl8169_set_features() and rtl_hw_start().
- Don't deal with RX_VLAN_8125 in rtl_init_rxcfg(), it will be set
by rtl_set_rx_config_features().
- Don't handle NETIF_F_RXALL in rtl_set_rx_mode().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's sufficient to do the masking once in probe() for clearing
unwanted bits that may have been set by the BIOS.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function devm_mdiobus_register() to simplify the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A barrier is needed here to ensure that rtl_tx sees the descriptor
changes (DescOwn set) before the updated tp->cur_tx value. Else it may
wrongly assume that the transfer has been finished already. For this
purpose smp_wmb() is sufficient.
No separate barrier is needed for ordering the descriptor changes
with the MMIO doorbell write. The needed barrier is included in
the non-relaxed writel() used by rtl8169_doorbell().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inline rtl8169_make_unusable_by_asic() and simplify it:
- Address field doesn't need to be poisoned because descriptor is
owned by CPU now
- desc->opts1 is set by rtl8169_mark_to_asic() and rtl8169_rx_fill(),
therefore we don't have to preserve any field parts.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_mark_as_last_descriptor() has just one user, so inline it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Realtek PHY driver takes care of adding the needed delay now,
therefore we can remove the delay here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add workaround for hw issues with TSO on RTL8168evl. This workaround is
based on information I got from Realtek, and *should* allow to safely
enable TSO on this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code and avoid the overhead of calling vlan_get_protocol().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At that place in rtl_init_one() we can safely use rtl8169_set_features()
to configure the chip according to the default features.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we set RX_VLAN_8125 unconditionally, even if
NETIF_F_HW_VLAN_CTAG_RX may not be set. Don't touch these bits,
and let only rtl8169_set_features() control them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_HIGHDMA is added to vlan_features by register_netdev(),
therefore we can omit this here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move setting the ocp_base to rtl_init_one(). Where supported the value
is always the same, and if not supported it doesn't hurt.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There has been a number of reports that using SG/TSO on different chip
versions results in tx timeouts. However for a lot of people SG/TSO
works fine. Therefore disable both features by default, but allow users
to enable them. Use at own risk!
Fixes: 93681cd7d9 ("r8169: enable HW csum and TSO")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out mapping the tx skb to a new function rtl8169_tx_map(). This
allows to remove redundancies, and rtl8169_get_txd_opts1() has only
one user left, so it can be inlined.
As a result rtl8169_xmit_frags() is significantly simplified, and in
rtl8169_start_xmit() the code is simplified and better readable.
No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the mtu is greater than TD_MSS_MAX, then TSO is disabled, see
rtl8169_fix_features(). Because mss is less than mtu, we can't have
the case mss > TD_MSS_MAX in the TSO path.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Android/x86 the module loading infrastructure can't deal with
softdeps. Therefore the check for presence of the Realtek PHY driver
module fails. mdiobus_register() will try to load the PHY driver
module, therefore move the check to after this call and explicitly
check that a dedicated PHY driver is bound to the PHY device.
Fixes: f325937735 ("r8169: check that Realtek PHY driver module is loaded")
Reported-by: Chih-Wei Huang <cwhuang@android-x86.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The original change fixed an issue on RTL8168b by mimicking the vendor
driver behavior to disable MSI on chip versions before RTL8168d.
This however now caused an issue on a system with RTL8168c, see [0].
Therefore leave MSI disabled on RTL8168b, but re-enable it on RTL8168c.
[0] https://bugzilla.redhat.com/show_bug.cgi?id=1792839
Fixes: 003bd5b4a7 ("r8169: don't use MSI before RTL8168d")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far only the reset bit it set, but the handler executing the reset
is not scheduled. Therefore nothing will happen until some other action
schedules the handler. Improve this by ensuring that the handler is
scheduled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation makes the implicit assumption that if a bit
is set, then the work is scheduled already. Remove the need for this
implicit assumption and call schedule_work() always. It will check
internally whether the work is scheduled already.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently rtl_task() is designed to handle a large number of tasks.
However we have just one, so we can remove some overhead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let netdev_stats_to_stats64() do the copy work for us.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing opts2 belongs to preparing the descriptor for DMA engine use.
Therefore move it into rtl8169_mark_to_asic().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until ae84bc1873 ("r8169: don't use bit LastFrag in tx descriptor
after send") we used to access another bit in the descriptor, therefore
it seems the barrier was needed. Since this commit DescOwn is the
only bit we're interested in, so the barrier isn't needed any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the parameters taken by rtl8169_unmap_tx_skb, this makes
usage of this function easier to read and understand.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far tx_skb->skb is the only member of the two structs that is not
reset. Make understanding the code easier by resetting both structs
completely in rtl8169_unmap_tx_skb.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slightly improve the code by converting this while to a for loop.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper pci_status_get_and_clear_errors() to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of factoring out PCI_STATUS error bit handling let drivers
use the same collection of error bits. To facilitate bisecting we do this
in a separate patch per affected driver. For the r8169 driver we have to
add PCI_STATUS_PARITY to the error bits.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only call rtl8169_xmit_frags() if the skb is actually fragmented.
This avoid a small overhead for non-fragmented skb's, and it allows
to simplify rtl8169_xmit_frags() a little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These constants are used in one place only, so we can remove them and
use the values directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code by using the new helper tcp_v6_gso_csum_prep.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register RxMissed exists on few early chip versions only, however all
chip versions have the number of missed RX packets in the hardware
counters. Therefore remove using RxMissed and get the number of missed
RX packets from the hardware stats.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge enabling and disabling jumbo packets to one function to make
the code a little simpler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently code snippet (RTL_R32(tp, TxConfig) >> 20) & 0xfcf is used
in few places to extract the chip XID. Change the code to do the XID
extraction only once.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In few places we do a PCI commit by reading an arbitrary chip register.
It's not always obvious that the read is meant to be a PCI commit,
therefore add a helper for it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting dev->features a few lines later allows to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done for all RTL8169 chip versions in rtl8169_init_phy already.
Therefore we can remove it here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_link_chg_patch() can be called from rtl_open() to rtl8169_close()
only. And in rtl8169_close() phy_stop() ensures that this function
isn't called afterwards. So we don't need this check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turned out that on low performance systems the original change can
cause lower tx performance. On a N3450-based mini-PC tx performance
in iperf3 was reduced from 950Mbps to ~900Mbps. Therefore effectively
revert the original change, just use pcie_set_readrq() now instead of
changing the PCIe capability register directly.
Fixes: 2df49d3654 ("r8169: remove fiddling with the PCIe max read request size")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defaults for min_mtu and max_mtu are set by ether_setup(), which is
called from devm_alloc_etherdev(). Let rtl_jumbo_max() only return
a positive value if actually jumbo packets are supported. This also
allows to remove constant Jumbo_1K which is a little misleading anyway.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We just added phy_do_ioctl, but it turned out that we need another
version of this function that doesn't check whether net_device is
running. So rename phy_do_ioctl to phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace rtl8169_ioctl with new generic function phy_do_ioctl.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move chip-specific PHY configurations to separate source file
r8169_phy_config.c. This improves maintainability of the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of factoring out PHY configuration to a separate source
file move commonly used definitions to new header file r8169.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename rtl_apply_firmware() to r8169_apply_firmware() before exporting
it to avoid namespace clashes with other drivers for Realtek hardware.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the phy_device as parameter to rtl8168d_apply_firmware_cond(),
this avoids having to access rtl8169_private internals.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace rtl_writephy and rtl_readphy with the respective phylib
functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move configuring EEE on MAC side out of the PHY configuration.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Writing this ERI register is a MAC setting, so move it to
rtl_hw_start_8106().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch rtl_writephy_batch() to phylib functions, as a result we can
avoid passing a rtl8169_private parameter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions use only the phy_device member of rtl8169_private,
so we can pass the phy_device as parameter directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions use only the phy_device member of rtl8169_private,
so we can pass the phy_device as parameter directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of factoring out rtl8169scd_hw_phy_config() move this
quirk to rtl8169_init_phy().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a useless debug statement. This also allows to remove the
net_device parameter from rtl8169_init_phy().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preperation of factoring out the PHY configuration to a separate
source file this patch:
- avoids accessing rtl8169_private internals by passing the phy_device
and mac_version as separate parameters
- renames rtl_hw_phy_config to r8169_hw_phy_config to avoid namespace
clashes with other drivers for Realtek hardware
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use constant EnAnaPLL for bit 14 as in vendor driver. The vendor
driver sets this bit for chip version 02 only, but I'm not aware of
any issues, so better leave it as it is.
In addition remove the useless debug message.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code by moving the call to rtl_enable_eee() from the
individual PHY configs to rtl8169_init_phy().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to recent changes we don't need the call to rtl_rar_exgmac_set()
and longer at this place. It's called from rtl_rar_set() which is
called in rtl_init_mac_address() and rtl8169_resume().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify and factor out this magic from rtl8168h_2_hw_phy_config()
and name it based on the vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some users complained about problems with r8169 and it turned out that
the generic PHY driver was used instead instead of the dedicated one.
In all cases reason was that r8169.ko was in initramfs, but realtek.ko
not. Manually adding realtek.ko to initramfs fixed the issues.
Root cause seems to be that tools like dracut and genkernel don't
consider softdeps. Add a check for loaded Realtek PHY driver module
and provide the user with a hint if it's not loaded.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In referenced fix we removed the RTL8168e-specific jumbo config for
RTL8168evl in rtl_hw_jumbo_enable(). We have to do the same in
rtl_hw_jumbo_disable().
v2: fix referenced commit id
Fixes: 14012c9f3b ("r8169: fix jumbo configuration for RTL8168evl")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8125 also requires to enable RX for WoL.
v2: add missing Fixes tag
Fixes: f1bce4ad2f ("r8169: add support for RTL8125")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported [0] that network doesn't wake up on cable plug-in with
certain chip versions. Reason is that on these chip versions the PHY
doesn't detect cable plug-in when being in power-down mode. So prevent
the PHY from powering down if WoL is enabled.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202103
Fixes: 95fb8bb318 ("net: phy: force phy suspend when calling phy_stop")
Reported-by: jhdskag3 <jhdskag3@tutanota.com>
Tested-by: jhdskag3 <jhdskag3@tutanota.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan reported [0] that network is broken since the referenced commit
when using jumbo frames. This commit isn't wrong, it just revealed
another issue that has been existing before. According to the vendor
driver the RTL8168e-specific jumbo config doesn't apply for RTL8168evl.
[0] https://lkml.org/lkml/2019/11/30/119
Fixes: 4ebcb113ed ("r8169: fix jumbo packet handling on resume from suspend")
Reported-by: Alan J. Wylie <alan@wylie.me.uk>
Tested-by: Alan J. Wylie <alan@wylie.me.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
During performance testing, I found that one of my r8169 NICs suffered
a major performance loss, a 8168c model.
Running netperf's TCP_STREAM test didn't return the expected
throughput of > 900 Mb/s, but rather only about 22 Mb/s. Strange
enough, running the TCP_MAERTS and UDP_STREAM tests all returned with
throughput > 900 Mb/s, as did TCP_STREAM with the other r8169 NICs I can
test (either one of 8169s, 8168e, 8168f).
Bisecting turned up commit 93681cd7d9,
"r8169: enable HW csum and TSO" as the culprit.
I added my 8168c version, RTL_GIGA_MAC_VER_22, to the code
special-casing the 8168evl as per the patch below. This fixed the
performance problem for me.
Fixes: 93681cd7d9 ("r8169: enable HW csum and TSO")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load Realtek-provided firmware for RTL8168fp/RTL8117. Unlike the
firmware for other chip versions which is for the PHY, firmware for
RTL8168fp/RTL8117 is for the MAC.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using constant MII_EXPANSION is misleading here because register 0x06
has a different meaning on page 0x0005. Here a proprietary PHY
parameter is read by writing the parameter id to register 0x05 on page
0x0005, followed by reading the parameter value from register 0x06.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use r8168d_modify_extpage() also in rtl8168f_config_eee_phy() to
simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for chip version RTL8117. Settings have been copied from
Realtek's r8168 driver, there however chip ID 54a belongs to a chip
version called RTL8168FP. It was confirmed that RTL8117 works with
Realtek's driver, so both chip versions seem to be the same or at
least compatible.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
