Instead of creating two DVB frontend entries for the same device,
create just one entry, and fill the delivery_system according with
the supported standards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ops.info.frequency_stepsize is used only for DVB-T & friends. For
DVB-C, the step size is calculated using the symbol rate.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While the driver has support for both serial and parallel mode,
There's was way to select serial mode via configuration. Add
a config option for that, while keeping the default in serial mode.
Also, at debug mode, it will now print a message when mpeg is
enabled/disabled, and showing if parallel or serial mode were
selected, helping developers to double-check if the DRX-K is at
the right mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that this field is deprecated, and core generates it for
DVBv3 calls, remove it from the drivers.
It also adds .delsys on the few drivers where this were missed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using dvb_frontend_parameters struct, that were
designed for a subset of the supported standards, use the DVBv5
cache information.
Also, fill the supported delivery systems at dvb_frontend_ops
struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Creates a DVBv5 get_frontend call, renaming the DVBv3 one to
get_frontend_legacy(), while not all frontends are converted.
After the conversion for all drivers, get_frontend_legacy()
will be removed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Passing DVBv3 parameters to set_frontend is not fun, as the
core doesn't have any way to know if the driver is using the
v3 or v5 parameters. So, rename the callback and add a new
one to allow distinguish between a mixed v3/v5 paramenter call
from a pure v5 call.
After having all frontends to use the new way, the legacy
call can be removed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a big patch, yet trivial: now that all tuners use the DVBv5
way to pass parameters (e. g. via fe->dtv_property_cache), the
extra parameter can be removed from set_params() call.
After this change, very few DVBv3 specific stuff are left at the
tuners.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using a roll-off factor, change DRX-K & friends to select
the bandwidth filter and the Nyquist half roll-off via delivery system.
This provides a cleaner support for Annex A/C switch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The DRX-K doesn't change the delivery system at set_properties,
but do it at frontend init. This causes problems on programs like
w_scan that, by default, opens both frontends.
Instead, explicitly set the format when set_parameters callback is
called.
Tested-by: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With this patch I try again to add initial support for HVR930C.
Tested only DVB-T, since in Italy Analog service is stopped.
Actually "scan -a0 -f1", find only about 50 channel while 400 should
be available.
[mchehab@redhat.com: Tested with DVB-C and fixed a few whitespace issues]
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Annex C support were broken with the previous implementation,
as, at xc5000 and tda18271c2dd, it were choosing the wrong bandwidth
for some symbol rates.
At DRX-J, it were always selecting Annex A, even having Annex C
support coded there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tuners in general convert a high frequency carrier into an Intermediate
Frequency (IF).
Digital tuners like tda18271, xc3028, etc. generally allow changing the IF
frequency, although they generally have recommented settings for the IF.
Analog tuners, have a fixed IF frequency, that depends on the physical
characteristics of some analog components.
For digital tuners, it makes sense to have ways to configure IF,
via the tuner's configuration structure, like what's done inside the
tda18271-fe maps.
The demods need to know what IF is used by the tuner, as it will need
to convert internally from IF into baseband. Currently, the bridge driver
needs to fill a per-demod configuration struct for it, or pass it via
a dvb_attach parameter.
The tda18271 datasheet recommends to use different IF's for different
delivery system types and for different bandwidths.
The DRX-K demod also needs to know the IF frequency in order to work,
just like all other demods. However, as it accepts different delivery
systems (DVB-C and DVB-T), the IF may change if the standard and/or
bandwidth is changed.
So, the usual procedure of passing it via a config struct doesn't work.
One might try to code it as two separate IF frequencies, or even as a
table in function of the delivery system and the bandwidth, but this
will be messy.
So, it is better and simpler to just add a new callback for it and
require the tuners that can be used with MFE frontends like drx-k
to implement a new callback to return the used IF.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Fix the DRX-K logic that selects between DVB-C annex A and C
Fix a typo where DVB-C annex type is set via setEnvParameters, but
the driver, uses, instead, setParamParameters[2].
While here, cleans up the code, fixing a bad identation at the fallback
code for other types of firmware, and put the multiple-line comments
into the Linux CodingStyle.
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After return, we don't need any other statement to change the
function flux ;)
Reported-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The error propagation changeset c23bf4402 broke the DVB-T
code.
The legacy way for propagate errors was:
do {
status = foo_func()
if (status < 0)
break;
} while (0);
return status;
However, on a few places, it was doing:
do {
switch(foo) {
case bar:
status = foo_func()
if (status < 0)
break;
break;
}
switch(foo2) {
case bar:
status = foo_func()
if (status < 0)
break;
break;
}
...
} while (0);
return (status)
The inner error break were not working, as it were breaking only
the switch, instead of the do. The solution used were to do a
s/break/goto error/ at the inner breaks, but preserving the last
break. Onfortunately, on a few switches, the replacement were
applied also to the final break for the case statements.
Fix the broken logic, by reverting them to break, where pertinent,
in order to fix DVB-T support.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both ngene and ddbrige calls dvb_attach once for drxk_attach.
The logic used there, and by tda18271c2dd driver is different
from similar logic on other frontends.
The right fix is to change them to use the same logic, but,
while we don't do that, we need to patch em28xx-dvb in order
to do cope with ngene/ddbridge magic.
While here, document why drxk_t_release should do nothing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The QAM standard is set using this scu_command:
SCU_RAM_COMMAND_STANDARD_QAM |
SCU_RAM_COMMAND_CMD_DEMOD_SET_PARAM
The driver implements a version that has 4 parameters, however,
Terratec H5 needs to break this into two separate commands, otherwise,
DVB-C doesn't work.
With this fix, scan is now properly working and getting the
channel list:
>>> tune to: 609000000:INVERSION_AUTO:5217000:FEC_3_4:QAM_256
>>> tuning status == 0x00
>>> tuning status == 0x07
>>> tuning status == 0x1f
0x0093 0x0026: pmt_pid 0x0758 (null) -- SporTV2 (running, scrambled)
0x0093 0x0027: pmt_pid 0x0748 (null) -- SporTV (running, scrambled)
0x0093 0x0036: pmt_pid 0x0768 (null) -- FX (running, scrambled)
0x0093 0x0052: pmt_pid 0x0788 (null) -- The History Channel (running, scrambled)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, it outputs:
[10927.639641] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
[10927.646283] drxk: 02 00 00 00 10 00 07 00 03 02 ..........
Better than ERROR -3. This happens with Terratec H5 firmware.
It adds 2 new error conditions, and something useful to track
what the heck is that.
I suspect that the scu_command is dependent on the firmware
revision.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver is too limited: it assumes that UIO is used only for
controlling the antenna, and that only UIO-1 is in usage. However,
from Terratec H7 driver [1], 3 UIO's can be used. In fact, it seems
that H7 needs to use all 3. So, make the code generic enough to handle
the most complex scenario. For now, only antena GPIO can be specified,
but is is easier now to add the other GPIO/UIO needs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DRX-K configuration is interesting when writing/testing
new devices. Add an info line showing the discovered info.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Terratec H5 doesn't require to switch mode, but generates
an error due to this logic. Also, GPIO's are board-dependent.
So, add it at the board config struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The set mode routines assume that state were changed to the
new mode, otherwise, they'll fail.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is very big and complex. An error happening in the middle
of any initialization may cause the frontend to not work. So, it
needs to properly propagate error codes internally and to userspace.
Also, printing the error codes at the places it happened helps to
discover were's a bug at the code.
Before this change, a do { } while (0) loop and lots of breaks inside
were used to propagate errors. While this works, if there are
loops inside other loops, it could be easy to forget to add another
break, causing the error to not abort the function.
Also, as not all functions were reporting errors, it is hard to
discover why something failed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On em28xx, tda18271C2 is accessible when the i2c port
is not touched. Touching on it breaks the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The microcode firmware provided on Terratec H5 seems to be
different. Add a parameter to allow specifying a different
firmware per-device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using #ifdef I2C_LONG_ADR for some devices, convert
it into a parameter. Terratec H5 logs from the original driver
seems to need this mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the only parameter to be configured is the I2C
address. However, Terratec H5 logs shows that it needs a different
setting for some things, and it has its own firmware.
So, move the addr into a config structure, in order to allow adding
the required configuration bits.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The normal 16-bits read routine is called as "Read16_0". This is
due to a flags that could optionally be passed. Yet, on no places
at the code, a flag is passed there.
The same happens with 16-bits write and 32-read/write routines,
and with WriteBlock.
Also, using flags, is an exception: there's no place currently using
flags, except for an #ifdef at WriteBlock.
Rename the function as just "read16", and the one that requires flags,
as "read16_flags".
This helps to see where the flags are used, and also avoid using
CamelCase on Kernel.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a complex driver. Adding support for other devices with drxk
requires to be able to debug it and see where it is failing. So, add
optional printk messages to allow debugging it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is hard to identify the origin for those errors without a
prefix to indicate which driver produced them:
[ 1390.220984] i2c_write error
[ 1390.224133] I2C Write error
[ 1391.284202] i2c_read error
[ 1392.288685] i2c_read error
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
One of the problems of the old CHECK_ERROR is that it was hiding
the status parameter. Maybe due to that, on a few places, the return
code might lead to return incorrect status:
drivers/media/dvb/frontends/drxk_hard.c: In function ‘load_microcode.clone.0’:
drivers/media/dvb/frontends/drxk_hard.c:1281: warning: ‘status’ may be used uninitialized in this function
drivers/media/dvb/frontends/drxk_hard.c:1281: note: ‘status’ was declared here
drivers/media/dvb/frontends/drxk_hard.c: In function ‘GetLockStatus’:
drivers/media/dvb/frontends/drxk_hard.c:1792: warning: ‘status’ may be used uninitialized in this function
drivers/media/dvb/frontends/drxk_hard.c: In function ‘Start.clone.7’:
drivers/media/dvb/frontends/drxk_hard.c:1734: warning: ‘status’ may be used uninitialized in this function
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/drxk_hard.c: In function ‘SetDVBT’:
drivers/media/dvb/frontends/drxk_hard.c:3766: warning: enumeration value ‘BANDWIDTH_5_MHZ’ not handled in switch
drivers/media/dvb/frontends/drxk_hard.c:3766: warning: enumeration value ‘BANDWIDTH_10_MHZ’ not handled in switch
drivers/media/dvb/frontends/drxk_hard.c:3766: warning: enumeration value ‘BANDWIDTH_1_712_MHZ’ not handled in switch
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CHK_ERROR macro does a flow control, violating chapter 12
of the Documentation/CodingStyle. Doing flow controls inside
macros is a bad idea, as it hides what's happening. It also
hides the var "status" with is also a bad idea.
The changes were done by this small perl script:
my $blk=0;
while (<>) {
s /^\s+// if ($blk);
$f =~ s/\s+$// if ($blk && /^\(/);
$blk = 1 if (!m/\#/ && m/CHK_ERROR/);
$blk=0 if ($blk && m/\;/);
s/\n/ / if ($blk);
$f.=$_;
};
$f=~ s,\n(\t+)CHK_ERROR\((.*)\)\;([^\n]*),\n\1status = \2;\3\n\1if (status < 0)\n\1\tbreak;,g;
print $f;
And manually fixed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/v4l/v4l/patchwork/drivers/media/dvb/frontends/drxk_hard.c:181: multiple definition of `MulDiv32'
drivers/media/dvb/frontends/drxd.o:/home/v4l/v4l/patchwork/drivers/media/dvb/frontends/drxd_hard.c:236: first defined here
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Driver for the DRX-K DVB-C/T demodulator.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
