The only real platform with DISPLAY_VER == 10 is GLK. We don't need to
handle CNL explicitly in intel_ddi.c.
A lot of special code for CNL can be removed. There were some
__cnl.*() functions that were created to share the implementation
between ICL and CNL. Those are now embedded in the only caller, in ICL.
Remove code and rename functions/macros accordingly to use ICL prefix
for those that are still needed.
Verified with:
make EXTRA_CFLAGS=-Wunused drivers/gpu/drm/i915/display/intel_dpll_mgr.o
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210729233934.2059489-1-lucas.demarchi@intel.com
Source needs to write DPCD 103-106 after receiving a PHY request to change
swing/pre-emphasis after reading DPCD 206-207. This is especially needed if
there is a retimer between source and sink and the retimer implements AUX_CH
interception scheme to manage DP PHY settings (e.g. adjusting Swing/Pre-emphasis
equalization level) for DP output channel. If the source doesn't write to
DPCD 103-106, the retimer may not output the requested swing/pre-emphasis and
eventually we fail compliance.
v2: Rebase and use crtc->lane_count (Imre)
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210226081554.984307-1-khaled.almahallawy@intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
ADL-P now has its own set of DDI buf translation tables (except for eDP
which appears to be the same as TGL). Add the new values (last updated
in bspec 2021-07-22) to the driver.
v2:
- Actually hook up the new tables via encoder->get_buf_trans()
v3:
- Create extra table wrapper structures for the tables from past
platforms that we're re-using, with names that more accurately
reflect the link rate they apply to on ADL-P specifically. (Jose)
Bspec: 49291
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Acked-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728221045.2363614-2-matthew.d.roper@intel.com
In discrete cards, the graphics driver shouldn't proceed with the probe
or resume unless PCODE indicated everything is done, including memory
training and gt bring up.
For this reason, the driver probe and resume paths needs to be blocked
until PCODE indicates it is done. Also, it needs to aborted if the
notification never arrives.
In general, the few miliseconds would be enough and the regular PCODE
recommendation for the timeout was 10 seconds. However there are some
rare cases where this initialization can take up to 1 minute. So,
PCODE has increased the recommendation to 3 minutes so we don't fully
block the device utilization when something just got delayed for
whatever reason. To be on the safest side, let's accept this
recommendation, since on the regular case it won't delay or block the
driver initialization and resume flows
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Badal Nilawar <badal.nilawar@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727173338.901264-1-badal.nilawar@intel.com
The driver doesn't depend atm on the common mode timing generator
functionality (it would be used for some power saving feature and panel
timing synchronization), however DMC will corrupt the CMTG registers
across DC5 entry/exit sequences unless the CMTG clock gating is
disabled. This in turn can lead to at least the DPLL0/1 configuration
getting stuck at their last state, which means we can't reprogram them
to a new config.
Add the corresponding Bspec workaround to prevent the above.
v2: Fix checkpatch errors. (CI, Jose)
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727134400.101290-1-imre.deak@intel.com
ADL_P requires that we disable underrun recovery when downscaling (or
using the scaler for YUV420 pipe output), using DSC, or using PSR2.
Otherwise we should be able to enable the underrun recovery.
On DG2 we need to keep underrun recovery disabled at all times, but the
chicken bit in PIPE_CHICKEN has an inverted meaning (it's an enable bit
instead of disable).
v2:
- Reverse the condition (clear the disable bit when supported, set
disable bit when not supported).
Bspec: 50351
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727145056.2049720-1-matthew.d.roper@intel.com
HDMI and DisplayPort sequences states that audio and PSR should be
disabled before planes are disabled.
Not following it did not caused any problems up to Alderlake-P but
for this platform it causes underruns during the PSR2 disable
sequence.
Specification don't mention that DRRS should be disabled before planes
but it looks safer to switch back to the default refresh rate before
following with the rest of the pipe disable sequence.
BSpec: 49191
BSpec: 49190
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210726181559.80855-1-jose.souza@intel.com
PSF GV points are an additional factor that can limit the
bandwidth available to display, separate from the traditional
QGV points. Whereas traditional QGV points represent possible
memory clock frequencies, PSF GV points reflect possible
frequencies of the memory fabric.
Switching between PSF GV points has the advantage of incurring
almost no memory access block time and thus does not need to be
accounted for in watermark calculations.
This patch adds support for those on top of regular QGV points.
Those are supposed to be used simultaneously, i.e we are always
at some QGV and some PSF GV point, based on the current video
mode requirements.
Bspec: 64631, 53998
v2: Seems that initial assumption made during ml conversation
was wrong, PCode rejects any masks containing points beyond
the ones returned, so even though BSpec says we have around
8 points theoretically, we can mask/unmask only those which
are returned, trying to manipulate those beyond causes a
failure from PCode. So switched back to generating mask
from 1 - num_qgv_points, where num_qgv_points is the actual
amount of points, advertised by PCode.
v3: - Extended restricted qgv point mask to 0xf, as we have now
3:2 bits for PSF GV points(Matt Roper)
- Replaced val2 with NULL from PCode request, since its not being
used(Matt Roper)
- Replaced %d to 0x%x for better readability(thanks for spotting)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210531064845.4389-2-stanislav.lisovskiy@intel.com
The fast path only updates cursor register what will not cause
any updates in the screen when using PSR2 selective fetch.
The only option that we have is to go through the slow patch that will
do full atomic commit, that will trigger the PSR2 selective fetch
compute and programing calls.
Without this patch is possible to see a mouse movement lag in Gnome
when PSR2 selective fetch is enabled.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210717011227.204494-3-jose.souza@intel.com
Commit 5a9d38b20a ("drm/i915/display: hide workaround for broken vbt
in intel_bios.c") moved the workaround for broken or missing VBT to
intel_bios.c. However is_port_valid() only protects the handling of
different skus of the same display version. Since in
intel_setup_outputs() we share the code path with version 9, this would
also create port F for SKL/KBL, which does not exist.
Missing VBT can be reproduced when starting a headless QEMU with no
opregion available.
Avoid the issue by splitting versions 9 and 10 in intel_setup_outputs(),
which also makes it more clear what code path it's taking for each
version.
v2: move generic display version after Geminilake since that one has
a different set of outputs
Fixes: 5a9d38b20a ("drm/i915/display: hide workaround for broken vbt in intel_bios.c")
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reported-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Christoph Hellwig <hch@lst.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210722232922.3796835-1-lucas.demarchi@intel.com
We were using GRAPHICS_VER() to handle SKL_DFSM register, which means we
were not handling GLK correctly since that has GRAPHICS_VER == 9, but
DISPLAY_VER == 10. Switch the entire branch to check DISPLAY_VER
which makes it more in line with Bspec.
Even though the Bspec has an exception for RKL in
TGL_DFSM_PIPE_D_DISABLE, we don't have to do anything as the bit has
disable semantic and RKL doesn't have pipe D.
Bspec: 50075, 7548
Fixes: 2b5a4562ed ("drm/i915/display: Simplify GLK display version tests")
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723234352.214459-1-lucas.demarchi@intel.com
A new step has been added to the DP modeset sequences for all platforms
with display version 12 and beyond: if enabling DP MST with FEC, we
need to set a chicken bit before enabling the transcoder. The chicken
bit should be disabled again before disabling the transcoder (which we
can do unconditionally since it shouldn't be set anyway in non-MST
cases).
Bspec: 49190, 54128, 55424
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723170618.1477415-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
DG2 doesn't have a SAGV or QGV points that determine memory bandwidth.
Instead it has a constant amount of memory bandwidth available to
display that does not need to be reduced based on the number of active
planes.
For simplicity, we'll just modify driver initialization to create a
single dummy QGV point with the proper amount of memory bandwidth,
rather than trying to query the pcode for this information.
Bspec: 64631
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721223043.834562-19-matthew.d.roper@intel.com
