Legacy state might not be updated any more.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds the intel_connector initialized to intel_hdmi
display, during the init phase, just like the other encoders do.
This attachment is very useful when we need to extract the connector
pointer during the hotplug handler function
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fall back to VBT based backlight modulation frequency if it's not
set. Do not hard code.
This could be a problem if there is no VBT.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Normally we determine the backlight PWM modulation frequency (which we
also use as backlight max value) from the backlight registers at module
load time, expecting the registers have been initialized by the BIOS. If
this is not the case, we fail.
The VBT contains the backlight modulation frequency in Hz. Add platform
specific functions to convert the frequency in Hz to backlight PWM
modulation frequency, and use them to initialize the backlight when the
registers are not initialized by the BIOS.
v2: Fix SPT and VLV. Thanks to Clint for the VLV code.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the difference between backlight control on HSW vs. BDW/SKL is
that on HSW we modify the duty cycle on the CPU register, and have the
hardware pass the changes on to the PCH registers. We still drive the
PCH PWM on both. While HSW and BDW use the same LPT PCH, BDW does not
pass these messages on to the PCH. Therefore on BDW we need to enable
the PCH override bit, and program the PCH directly. (On SPT PCH, this
mode is the default.) We could as well do this on HSW too, and in fact
I've been told this is what a certain other operating system does. So
use PCH backlight override on HSW too.
This simplifies some follow-up code, but it does have the danger of
breaking backlight on HSW machines. It should work, but mysterious are
the ways of backlight.
While at it, name the related backlight hooks according to the PCH
rather than the CPU for clarity.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add stepping check for A0 workarounds, and remove the associated
FIXME tags.
Split out unrelated WAs for later condition checking.
v2: Fixed format (PeterL)
v3: Corrected stepping check for WaDisableSDEUnitClockGating
- Ignoring comment, following hardware spec instead. (ChrisH)
Added description for TILECTL setting (JonB)
Cc: Peter Lawthers <peter.lawthers@intel.com>
Cc: Chris Harris <chris.harris@intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes regression from
commit f1afe24f0e
Author: Arun Siluvery <arun.siluvery@linux.intel.com>
Date: Tue Aug 4 16:22:20 2015 +0100
drm/i915: Change SRM, LRM instructions to use correct length
which forgot to account for the length bias when declaring the fixed
length.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91844
Reported-by: Andreas Reis <andreas.reis@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pfit state is stored as register values, so dump them as hex instead
of decimal to make some sense of the error messages.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These registers exist only before GEN5, so currently we may access
undefined registers on VLV/CHV and BXT. Apply the workaround only pre
GEN5.
Since the workaround is relevant only when LVDS is present, for clarity
apply it only if this is the case.
This triggered an unclaimed register access warning on BXT.
v2: (Ville)
- move the workaround to the LVDS init code
- print a debug note about the workaround
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This register exists only pre GEN5, but atm we also access it on
VLV/BXT/CHV. Prevent accessing it on these latter platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A small, very small, step to sharing the duplicate code between
execlists and legacy submission engines, starting with the ringbuffer
allocation code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
TPS3 is mandatory for downstream devices that support HBR2, and Intel
platforms that support HBR2 also support TPS3. Whenever TPS3 is
supported by both the source and sink, it should be used. In other
words, whenever the source and sink are capable of 5.4 Gbps link, we
should anyway go for TPS3, regardless of the link rate being selected.
Log an error if the sink has advertized HBR2 capability without TPS3
capability.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no need to have a separate flag for tps3 as the information is
only used at one location. Move the logic there to make it easier to
follow.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is another case where we can consider the default is the
newest available and not actually a missed case.
No functional change.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unless future specs tells otherwise we can assume future gens
inherit some stuff from the previous so let's handle
missed cases when we know tehy should't be there and assume
default equals newest one.
No functional changes.
v2: Remove useless case as pointed out by Ville.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These functions are already being called for gen >= 9,
so let's be sure when this happens we use whatever is
there already for the latest platform.
No functional change.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On each call to gen8_alloc_va_range_3lvl we're allocating temporary
bitmaps needed for error handling. Unfortunately, when we increase
address space size (48b ppgtt) we do additional (512 - 4) calls to
kcalloc, increasing latency between exec and actual start of execution
on the GPU. Let's just do a single kcalloc, we can also drop the size
from free_gen8_temp_bitmaps since it's no longer used.
v2: Use GFP_TEMPORARY to make the allocations reclaimable.
v3: Drop the 2D array, just allocate a single block.
v4: Rebase to handle gen8_preallocate_top_level_pdps.
v5: Align misaligned bracket.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Correct kcalloc arguments as suggested by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN >= 9 supports YUV format for all planes, but it's not exported in
Capability list of primary plane. Add YUV formats in skl_primary_formats
list.
Testcase: igt/kms_universal_plane.c
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Cc: Konduru, Chandra <chandra.konduru@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't rely on fb->bits_per_pixel as intel_framebuffer_init is not
filling bits_per_pixel field of fb-struct for YUV pixel format.
This leads to divide by zero error during watermark calculation.
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Cc: Konduru, Chandra <chandra.konduru@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On GMCH plaforms we are now getting the following spew on aux
interrupts:
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00000000, dig 0x00000000, pins 0x00000000
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00000000, dig 0x00000000, pins 0x00000000
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00000000, dig 0x00000000, pins 0x00000000
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00000000, dig 0x00000000, pins 0x00000000
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00000000, dig 0x00000000, pins 0x00000000
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x71450064
Prevent it by not calling intel_get_hpd_pins() unless one of the HPD
interrupt bits are actually set.
I already fixed similar annoyance once with
4bca26d0a6 drm/i915: Use HOTPLUG_INT_STATUS_G4X on VLV/CHV
but another source for it got added in
fd63e2a972 drm/i915: combine i9xx_get_hpd_pins and pch_get_hpd_pins
due to pch_get_hpd_pins() being chosen over i9xx_get_hpd_pins() to
serve as the new unified piece of code. pch_get_hpd_pins() had the debug
print, and i9xx_get_hpd_pins() didn't.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rewrite the BXT hpd setup to match the way we do it on other platforms:
- Throw out BXT_HOTPLUG_CTL since it's the same as PCH_PORT_HOTPLUG
- Enable the HPD bits in the DE port IER in gen8_de_irq_postinstall()
- Update DE port IMR using bdw_update_port_irq()
Also throw out port D from bxt_port_hotplug_long_detect() since BXT only
goes up to C.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A lot of the hpd irq handling is duplicated code, so refactor it a bit
by observing that in several places the only difference is the hpd[]
array. So pull the code to a few functions and pass in the hpd[] array
from the caller. Another option would be to determine the correct array
to use within the functions themselves, but somehow passing it in felt
nicer.
Further code reduction could be achieved by passing in the hotplug
register offset, and the long pulse detection function pointer. But that
didn't feel as good for some reason, so I left it at the middle ground.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
bxt_hpd_handler() looks different to everyone else for no good reason.
Rewrite it to use the standard variable namees etc.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Runtime suspends disabled all interrupts, so in order to get them back
fully we need to also do the HPD irq setup on runtime resume. Except
on VLV/CHV where the display interrupt initialization is part of the
display power well powerup.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SKL the port A HPD has moved to the PCH. Hook it up.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wire up the port A HPD for BDW. Compared to earlier platforms the
interrupt setup is a bit different, but basically everything else
looks the same.
v2: 0 initialize pin_mask/long_mask due to intel_get_hpd_pins() changes
Check for BDW before processing the HPD to not break BXT
Set found=true when processing port A HPD
Sort out the mess I made of the irq setup in v1
Warn about bad irq mask vs. enable bits in bdw_update_port_irq() (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the CPU and PCH are on the same package we must enabled the port A
HPD also in the south hotplug register. To identify the package type
we simply look at the PCH type: LPT-H means separate package, and
LPT-LP means multi chip package (MCP).
v2: Add comment and pimp commit message
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As with ILK/SNB wire up the port A HPD on IVB/HSW.
This might be more important on HSW with PSR. BSpec tells us that if the
automagic link training performed by the hardware fails for some reason,
we're going to get a short HPD and are supposed to re-train the link
manyally.
v2: 0 initialize pin_mask/long_mask due to intel_get_hpd_pins() changes
Add a comment about the pulse duration bits being reserved on HSW+
like we have for LPT+ in ibx_hpd_irq_setup()
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ILK/SNB support port A HPD. While HPD is optional on eDP let's at least
try to wite it up so that we might notice if the link has issues.
The eDP spec suggests that if HPD is not wired up, one should poll the
link status instead. We don't even do that currently.
v2: 0 initialize pin_mask/long_mask due to intel_get_hpd_pins() changes
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Starting from SPT the only interrupts living in the south are GMBUS and
HPD. What's worse some of the SPT specific new bits conflict with some
other bits on earlier PCH generations. So better not use the
cpt_irq_handler() for SPT+ anymore.
Also kill the hand rolled port E handling with something more
standardish. This also avoids accidentally confusing port B and port E
long pulses since the bits occupy the same positions, just in different
registers.
Also add a comment noting that the short pulse duration bits are
reserved on LPT+. The 2ms value we program is 0, so no issue wrt. the
MBZ in the spec.
v2: Call intel_hpd_irq_handler() only once (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the 0 initialization of pin_mask and long_mask from
intel_get_hpd_pins() into each caller. This we we can call
intel_get_hpd_pins() multiple times to accumulate more pins from several
sources.
v2: Add a comment explaining the dangers of intel_get_hpd_pins() (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The PORTA HPD defines are not BXT specific. They also exist on SPT,
and partially already on LPT:LP.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make LPT:LP checks look neater by wrapping the details in a
new HAS_PCH_LPT_LP() macro.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Extract the core of ironlake_{enable,disable}_display_irq() into a new
function. We'll have further use for it later.
v2: Warn about invalid mask vs. enable bits (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eliminate a bunch of duplicated code that calculates the currently
enabled HPD interrupt bits.
v2: s/;/:/ in patch subject (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Indent the PORTx_HOTPLUG_... defines appropriately, and fix some space
vs. tab issues.
v2: Document pre-HSW/LPT bits, and order another tab (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Forgot to do that in
commit d328c9d78d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Apr 10 16:22:37 2015 +0200
drm/i915: Select starting pipe bpp irrespective or the primary plane
and it's confusing. Fix it.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Backmerge -fixes since there's more DDI-E related cleanups on top of
the pile of -fixes for skl that just landed for 4.3.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i914/intel_dp.c
drivers/gpu/drm/i915/intel_lrc.c
Conflicts are all fairly harmless adjacent line stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This makes the error message slightly more useful.
Changes since v1:
- Use ktime_get() while irqs are still disabled. (vsyrjala)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's already a per crtc member that can be used for it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When i915 drivers run inside a VM with Intel GVT-g, some explicit
notifications are needed from guest to host device model through PV
INFO page write. The notifications include:
PPGTT create
PPGTT destroy
They are used for the shadow implementation of PPGTT. Intel GVT-g
needs to write-protect the guest pages of PPGTT, and clear the write
protection when they end their life cycle.
v2:
- Use lower_32_bits()/upper_32_bits() for qword operations;
- Remove the notification of guest context creation/destroy;
Signed-off-by: Zhiyuan Lv <zhiyuan.lv@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some more definitions in the PV info page are added. They are mainly
for the guest notification to Intel GVT-g device model. They are used
for Broadwell enabling.
The notification of PPGTT page table creation/destroy is to notify
GVT-g device model the life cycle of guest page tables. Then device
model will implement shadow page table for guests.
The notification of context create/destroy is optional. If it is used,
the device model will create/destroy shadow context corresponding to
the context's life cycle. Guest driver needs to make sure that the
context's LRCA and backing storage address unchanged. If it is not
used, the device model will perform the context shadow work in the
context scheduling time.
Signed-off-by: Zhiyuan Lv <zhiyuan.lv@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broadwell hardware supports both ring buffer mode and execlist mode.
When i915 runs inside a VM with Intel GVT-g, we allow execlist mode
only.
The main reason of EXECLIST only is that GVT-g does not support the
dynamic mode switch between ring buffer mode and execlist mode when
running multiple virtual machines.
v2:
- Adjust the position of vgpu check in sanitize function (Joonas)
- Add vgpu error check in context initialization. (Joonas, Daniel)
Signed-off-by: Zhiyuan Lv <zhiyuan.lv@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is based on Mika Kuoppala's patch below:
http://article.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/61104/match=workaround+hw+preload
The patch will preallocate the page directories for 32-bit PPGTT when
i915 runs inside a virtual machine with Intel GVT-g. With this change,
the root pointers in EXECLIST context will always keep the same.
The change is needed for vGPU because Intel GVT-g will do page table
shadowing, and needs to track all the page table changes from guest
i915 driver. However, if guest PPGTT is modified through GPU commands
like LRI, it is not possible to trap the operations in the right time,
so it will be hard to make shadow PPGTT to work correctly.
Shadow PPGTT could be much simpler with this change. Meanwhile
hypervisor could simply prohibit any attempt of PPGTT modification
through GPU command for security.
The function gen8_preallocate_top_level_pdps() in the patch is from
Mika, with only one change to set "used_pdpes" to avoid duplicated
allocation later.
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Zhiyuan Lv <zhiyuan.lv@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a common function to return "yes" or "no" string based on the
argument, and drop the local versions of it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make it available outside of intel_dp.c.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If rc6 is enabled, notify GuC so it can do proper forcewake before
command submission.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The firmware layout changes that now it only has css header +
uCode + RSA signature. Plus, other trivial changes to support
GuC V4.3.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
