A number of problems can occur due to races between
resync/recovery and discard.
- if sync_request calls handle_stripe() while a discard is
happening on the stripe, it might call handle_stripe_clean_event
before all of the individual discard requests have completed
(so some devices are still locked, but not all).
Since commit ca64cae960
md/raid5: Make sure we clear R5_Discard when discard is finished.
this will cause R5_Discard to be cleared for the parity device,
so handle_stripe_clean_event() will not be called when the other
devices do become unlocked, so their ->written will not be cleared.
This ultimately leads to a WARN_ON in init_stripe and a lock-up.
- If handle_stripe_clean_event() does clear R5_UPTODATE at an awkward
time for resync, it can lead to s->uptodate being less than disks
in handle_parity_checks5(), which triggers a BUG (because it is
one).
So:
- keep R5_Discard on the parity device until all other devices have
completed their discard request
- make sure we don't try to have a 'discard' and a 'sync' action at
the same time.
This involves a new stripe flag to we know when a 'discard' is
happening, and the use of R5_Overlap on the parity disk so when a
discard is wanted while a sync is active, so we know to wake up
the discard at the appropriate time.
Discard support for RAID5 was added in 3.7, so this is suitable for
any -stable kernel since 3.7.
Cc: stable@vger.kernel.org (v3.7+)
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD RAID5: Fix kernel oops when RAID4/5/6 is used via device-mapper
Commit a9add5d (v3.8-rc1) added blktrace calls to the RAID4/5/6 driver.
However, when device-mapper is used to create RAID4/5/6 arrays, the
mddev->gendisk and mddev->queue fields are not setup. Therefore, calling
things like trace_block_bio_remap will cause a kernel oops. This patch
conditionalizes those calls on whether the proper fields exist to make
the calls. (Device-mapper will call trace_block_bio_remap on its own.)
This patch is suitable for the 3.8.y stable kernel.
Cc: stable@vger.kernel.org (v3.8+)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Since commit 1ed850f356
md/raid5: make sure to_read and to_write never go negative.
It has been possible for handle_stripe_dirtying to be called
when there isn't actually any work to do.
It then calls schedule_reconstruction() which will set R5_LOCKED
on the parity block(s) even when nothing else is happening.
This then causes problems in do_release_stripe().
So add checks to schedule_reconstruction() so that if it doesn't
find anything to do, it just aborts.
This bug was introduced in v3.7, so the patch is suitable
for -stable kernels since then.
Cc: stable@vger.kernel.org (v3.7+)
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This doesn't seem to actually help and we have an alternate
multi-threading approach waiting in the wings, so just get
rid of this config option and associated code.
As a bonus, we remove one use of CONFIG_EXPERIMENTAL
Cc: Dan Williams <djbw@fb.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Mostly just little fixes. Probably biggest part is
AVX accelerated RAID6 calculations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=uK52
-----END PGP SIGNATURE-----
Merge tag 'md-3.8' of git://neil.brown.name/md
Pull md update from Neil Brown:
"Mostly just little fixes. Probably biggest part is AVX accelerated
RAID6 calculations."
* tag 'md-3.8' of git://neil.brown.name/md:
md/raid5: add blktrace calls
md/raid5: use async_tx_quiesce() instead of open-coding it.
md: Use ->curr_resync as last completed request when cleanly aborting resync.
lib/raid6: build proper files on corresponding arch
lib/raid6: Add AVX2 optimized gen_syndrome functions
lib/raid6: Add AVX2 optimized recovery functions
md: Update checkpoint of resync/recovery based on time.
md:Add place to update ->recovery_cp.
md.c: re-indent various 'switch' statements.
md: close race between removing and adding a device.
md: removed unused variable in calc_sb_1_csm.
Pull block driver update from Jens Axboe:
"Now that the core bits are in, here are the driver bits for 3.8. The
branch contains:
- A huge pile of drbd bits that were dumped from the 3.7 merge
window. Following that, it was both made perfectly clear that
there is going to be no more over-the-wall pulls and how the
situation on individual pulls can be improved.
- A few cleanups from Akinobu Mita for drbd and cciss.
- Queue improvement for loop from Lukas. This grew into adding a
generic interface for waiting/checking an even with a specific
lock, allowing this to be pulled out of md and now loop and drbd is
also using it.
- A few fixes for xen back/front block driver from Roger Pau Monne.
- Partition improvements from Stephen Warren, allowing partiion UUID
to be used as an identifier."
* 'for-3.8/drivers' of git://git.kernel.dk/linux-block: (609 commits)
drbd: update Kconfig to match current dependencies
drbd: Fix drbdsetup wait-connect, wait-sync etc... commands
drbd: close race between drbd_set_role and drbd_connect
drbd: respect no-md-barriers setting also when changed online via disk-options
drbd: Remove obsolete check
drbd: fixup after wait_even_lock_irq() addition to generic code
loop: Limit the number of requests in the bio list
wait: add wait_event_lock_irq() interface
xen-blkfront: free allocated page
xen-blkback: move free persistent grants code
block: partition: msdos: provide UUIDs for partitions
init: reduce PARTUUID min length to 1 from 36
block: store partition_meta_info.uuid as a string
cciss: use check_signature()
cciss: cleanup bitops usage
drbd: use copy_highpage
drbd: if the replication link breaks during handshake, keep retrying
drbd: check return of kmalloc in receive_uuids
drbd: Broadcast sync progress no more often than once per second
drbd: don't try to clear bits once the disk has failed
...
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
handle_stripe_expansion contains:
if (tx) {
async_tx_ack(tx);
dma_wait_for_async_tx(tx);
}
which is very similar to the body of async_tx_quiesce(),
except that the later handles an error from dma_wait_for_async_tx()
(admittedly by panicing, but that decision belongs in the dma
code, not the md code).
So just us async_tx_quiesce().
Acked-by: Dan Williams <djbw@fb.com>
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NeilBrown <neilb@suse.de>
New wait_event{_interruptible}_lock_irq{_cmd} macros added. This commit
moves the private wait_event_lock_irq() macro from MD to regular wait
includes, introduces new macro wait_event_lock_irq_cmd() instead of using
the old method with omitting cmd parameter which is ugly and makes a use
of new macros in the MD. It also introduces the _interruptible_ variant.
The use of new interface is when one have a special lock to protect data
structures used in the condition, or one also needs to invoke "cmd"
before putting it to sleep.
All new macros are expected to be called with the lock taken. The lock
is released before sleep and is reacquired afterwards. We will leave the
macro with the lock held.
Note to DM: IMO this should also fix theoretical race on waitqueue while
using simultaneously wait_event_lock_irq() and wait_event() because of
lack of locking around current state setting and wait queue removal.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
commit 9e44476851
MD: raid5 avoid unnecessary zero page for trim
change raid5 to clear R5_Discard when the complete request is
handled rather than when submitting the per-device discard request.
However it did not clear R5_Discard for the parity device.
This means that if the stripe_head was reused before it expired from
the cache, the setting would be wrong and a hang would result.
Also if the R5_Uptodate bit happens to be set, R5_Discard again
won't be cleared. But R5_Uptodate really should be clear at this point.
So make sure R5_Discard is cleared in all cases, and clear
R5_Uptodate when a 'discard' completes.
Signed-off-by: NeilBrown <neilb@suse.de>
stripe_handle.
The chunk of code in stripe_handle which responds to a
*_result value in reconstruct_state is really the completion
of some processing that happened outside of handle_stripe
(possibly asynchronously) and so should be one of the first
things done in handle_stripe().
After the next patch it will be important that it happens before
handle_stripe_clean_event(), as that will clear some dev->flags
bit that this code tests.
Signed-off-by: NeilBrown <neilb@suse.de>
blkdev_issue_discard currently assumes that the granularity
is a power of 2. So in raid5, round the chosen number up to
avoid embarrassment.
Cc: Shaohua Li <shli@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.de>
"discard" support, some dm-raid improvements and other assorted
bits and pieces.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQIVAwUAUHk6Rjnsnt1WYoG5AQKovQ//Ym0ROo5a6uekb2USLyFSdQH3TC7z0v0+
+kujrgoc4nHZU/vj5yfMvPVomEUsAhHEwTkvvCiXFFHn6cxPzC8ezm8d40xEeISX
qp6i2bPlvGURhsW1tYeD+THtY82/oyzQ4Wa/vaE1sjVLQ+caa2q7kVVgAL9Bj/Kz
aESIZjAuPxQNE1674/KR0EmMFcbpd0z1WDV+ydKlRV5jHCHGYf8OmxOenJFf+V/b
/f9p2u+NUq5BN5WLhThcysO8lPX1Y7GG8IYay3DlSt/crU24R2a2j0qh/BDoK8+t
/DceoHipbIiGxXLVjM7y+1RwPpCh75HJSZQHltPype2Z3iwtwEth9uTkEE3M2h/W
tOQEbOZku0kcgsrys7JBmpkBwkR9oZqq1kDd4YBzqW4PiGVP6z0JRH8QpjjB+mjN
47ODYIZcaEYZ+0Jj8kcVxo3gv4Xj4DWH+auSNZihTVmjQPVqrcy3CAt3CkuDzTkY
34fZVuCDiCetLGCGQKrwfMDnySVy5xOmtC6iWsEY5rExAeb0E+BCzcBvbAXzt+ef
MPDsrxWbo/ZkvpuwXOwLFTccBuRtAsFi7CM4jcow53W6XMnPpdubphNw5nylaEm1
DEzfID58mv8VHWRuW15vr7SbtROjYJkEFCIaEK3oprrRUYftZntIABcknqvcIYR+
/ULNzkRU1w4=
=XRmL
-----END PGP SIGNATURE-----
Merge tag 'md-3.7' of git://neil.brown.name/md
Pull md updates from NeilBrown:
- "discard" support, some dm-raid improvements and other assorted bits
and pieces.
* tag 'md-3.7' of git://neil.brown.name/md: (29 commits)
md: refine reporting of resync/reshape delays.
md/raid5: be careful not to resize_stripes too big.
md: make sure manual changes to recovery checkpoint are saved.
md/raid10: use correct limit variable
md: writing to sync_action should clear the read-auto state.
Subject: [PATCH] md:change resync_mismatches to atomic64_t to avoid races
md/raid5: make sure to_read and to_write never go negative.
md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
md/raid5: protect debug message against NULL derefernce.
md/raid5: add some missing locking in handle_failed_stripe.
MD: raid5 avoid unnecessary zero page for trim
MD: raid5 trim support
md/bitmap:Don't use IS_ERR to judge alloc_page().
md/raid1: Don't release reference to device while handling read error.
raid: replace list_for_each_continue_rcu with new interface
add further __init annotations to crypto/xor.c
DM RAID: Fix for "sync" directive ineffectiveness
DM RAID: Fix comparison of index and quantity for "rebuild" parameter
DM RAID: Add rebuild capability for RAID10
DM RAID: Move 'rebuild' checking code to its own function
...
When a RAID5 is reshaping, conf->raid_disks is increased
before mddev->delta_disks becomes zero.
This can result in check_reshape calling resize_stripes with a
number that is too large. This particularly happens
when md_check_recovery calls ->check_reshape().
If we use ->previous_raid_disks, we don't risk this.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that multiple threads can handle stripes, it is safer to
use an atomic64_t for resync_mismatches, to avoid update races.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
to_read and to_write are part of the result of analysing
a stripe before handling it.
Their use is to avoid some loops and tests if the values are
known to be zero. Thus it is not a problem if they are a
little bit larger than they should be.
So decrementing them in handle_failed_stripe serves little value, and
due to races it could cause some loops to be skipped incorrectly.
So remove those decrements.
Reported-by: "Jianpeng Ma" <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The pr_debug in add_stripe_bio could race with something
changing *bip, so it is best to hold the lock until
after the pr_debug.
Reported-by: "Jianpeng Ma" <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We really should hold the stripe_lock while accessing
'toread' else we could race with add_stripe_bio and corrupt
a list.
Reported-by: "Jianpeng Ma" <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We want to avoid zero discarded dev page, because it's useless for discard.
But if we don't zero it, another read/write hit such page in the cache and will
get inconsistent data.
To avoid zero the page, we don't set R5_UPTODATE flag after construction is
done. In this way, discard write request is still issued and finished, but read
will not hit the page. If the stripe gets accessed soon, we need reread the
stripe, but since the chance is low, the reread isn't a big deal.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Discard for raid4/5/6 has limitation. If discard request size is
small, we do discard for one disk, but we need calculate parity and
write parity disk. To correctly calculate parity, zero_after_discard
must be guaranteed. Even it's true, we need do discard for one disk
but write another disks, which makes the parity disks wear out
fast. This doesn't make sense. So an efficient discard for raid4/5/6
should discard all data disks and parity disks, which requires the
write pattern to be (A, A+chunk_size, A+chunk_size*2...). If A's size
is smaller than chunk_size, such pattern is almost impossible in
practice. So in this patch, I only handle the case that A's size
equals to chunk_size. That is discard request should be aligned to
stripe size and its size is multiple of stripe size.
Since we can only handle request with specific alignment and size (or
part of the request fitting stripes), we can't guarantee
zero_after_discard even zero_after_discard is true in low level
drives.
The block layer doesn't send down correctly aligned requests even
correct discard alignment is set, so I must filter out.
For raid4/5/6 parity calculation, if data is 0, parity is 0. So if
zero_after_discard is true for all disks, data is consistent after
discard. Otherwise, data might be lost. Let's consider a scenario:
discard a stripe, write data to one disk and write parity disk. The
stripe could be still inconsistent till then depending on using data
from other data disks or parity disks to calculate new parity. If the
disk is broken, we can't restore it. So in this patch, we only enable
discard support if all disks have zero_after_discard.
If discard fails in one disk, we face the similar inconsistent issue
above. The patch will make discard follow the same path as normal
write request. If discard fails, a resync will be scheduled to make
the data consistent. This isn't good to have extra writes, but data
consistency is important.
If a subsequent read/write request hits raid5 cache of a discarded
stripe, the discarded dev page should have zero filled, so the data is
consistent. This patch will always zero dev page for discarded request
stripe. This isn't optimal because discard request doesn't need such
payload. Next patch will avoid it.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Change the thread parameter, so the thread can carry extra info. Next patch
will use it.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit b17459c050
raid5: add a per-stripe lock
added a spin_lock to the 'stripe_head' struct.
Unfortunately there are two places where this struct is allocated
but the spin lock was only initialised in one of them.
So add the missing spin_lock_init.
Signed-off-by: NeilBrown <neilb@suse.de>
When a replacement device becomes active, we mark the device that it
replaces as 'faulty' so that it can subsequently get removed.
However 'calc_degraded' only pays attention to the primary device, not
the replacement, so the array appears to become degraded, which is
wrong.
So teach 'calc_degraded' to consider any replacement if a primary
device is faulty.
This is suitable for -stable as an incorrect 'degraded' value can
confuse md and could lead to data corruption.
This is only relevant for 3.3 and later.
Cc: stable@vger.kernel.org
Reported-by: Robin Hill <robin@robinhill.me.uk>
Reported-by: John Drescher <drescherjm@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This reverts commit 895e3c5c58.
While this patch seemed like a good idea and did help some workloads,
it hurts other workloads.
Large sequential O_DIRECT writes were faster,
Small random O_DIRECT writes were slower.
Other changes (batching RAID5 writes) have improved the sequential
writes using a different mechanism, so the net result of this patch
is definitely negative. So revert it.
Reported-by: Shaohua Li <shli@kernel.org>
Tested-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This contains a few patches that depend on
plugging changes in the block layer so needs to wait
for those.
It also contains a Kconfig fix for the new RAID10 support
in dm-raid.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=ovN2
-----END PGP SIGNATURE-----
Merge tag 'md-3.6' of git://neil.brown.name/md
Pull additional md update from NeilBrown:
"This contains a few patches that depend on plugging changes in the
block layer so needed to wait for those.
It also contains a Kconfig fix for the new RAID10 support in dm-raid."
* tag 'md-3.6' of git://neil.brown.name/md:
md/dm-raid: DM_RAID should select MD_RAID10
md/raid1: submit IO from originating thread instead of md thread.
raid5: raid5d handle stripe in batch way
raid5: make_request use batch stripe release
Let raid5d handle stripe in batch way to reduce conf->device_lock locking.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
make_request() does stripe release for every stripe and the stripe usually has
count 1, which makes previous release_stripe() optimization not work. In my
test, this release_stripe() becomes the heaviest pleace to take
conf->device_lock after previous patches applied.
Below patch makes stripe release batch. All the stripes will be released in
unplug. The STRIPE_ON_UNPLUG_LIST bit is to protect concurrent access stripe
lru.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull block driver changes from Jens Axboe:
- Making the plugging support for drivers a bit more sane from Neil.
This supersedes the plugging change from Shaohua as well.
- The usual round of drbd updates.
- Using a tail add instead of a head add in the request completion for
ndb, making us find the most completed request more quickly.
- A few floppy changes, getting rid of a duplicated flag and also
running the floppy init async (since it takes forever in boot terms)
from Andi.
* 'for-3.6/drivers' of git://git.kernel.dk/linux-block:
floppy: remove duplicated flag FD_RAW_NEED_DISK
blk: pass from_schedule to non-request unplug functions.
block: stack unplug
blk: centralize non-request unplug handling.
md: remove plug_cnt feature of plugging.
block/nbd: micro-optimization in nbd request completion
drbd: announce FLUSH/FUA capability to upper layers
drbd: fix max_bio_size to be unsigned
drbd: flush drbd work queue before invalidate/invalidate remote
drbd: fix potential access after free
drbd: call local-io-error handler early
drbd: do not reset rs_pending_cnt too early
drbd: reset congestion information before reporting it in /proc/drbd
drbd: report congestion if we are waiting for some userland callback
drbd: differentiate between normal and forced detach
drbd: cleanup, remove two unused global flags
floppy: Run floppy initialization asynchronous
This seemed like a good idea at the time, but after further thought I
cannot see it making a difference other than very occasionally and
testing to try to exercise the case it is most likely to help did not
show any performance difference by removing it.
So remove the counting of active plugs and allow 'pending writes' to
be activated at any time, not just when no plugs are active.
This is only relevant when there is a write-intent bitmap, and the
updating of the bitmap will likely introduce enough delay that
the single-threading of bitmap updates will be enough to collect large
numbers of updates together.
Removing this will make it easier to centralise the unplug code, and
will clear the other for other unplug enhancements which have a
measurable effect.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
'sync' writes set both REQ_SYNC and REQ_NOIDLE.
O_DIRECT writes set REQ_SYNC but not REQ_NOIDLE.
We currently assume that a REQ_SYNC request will not be followed by
more requests and so set STRIPE_PREREAD_ACTIVE to expedite the
request.
This is appropriate for sync requests, but not for O_DIRECT requests.
So make the setting of STRIPE_PREREAD_ACTIVE conditional on REQ_NOIDLE
rather than REQ_SYNC. This is consistent with the documented meaning
of REQ_NOIDLE:
__REQ_NOIDLE, /* don't anticipate more IO after this one */
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Because bios will merge at block-layer,so bios-error may caused by other
bio which be merged into to the same request.
Using this flag,it will find exactly error-sector and not do redundant
operation like re-write and re-read.
V0->V1:Using REQ_FLUSH instead REQ_NOMERGE avoid bio merging at block
layer.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Add a per-stripe lock to protect stripe specific data. The purpose is to reduce
lock contention of conf->device_lock.
stripe ->toread, ->towrite are protected by per-stripe lock. Accessing bio
list of the stripe is always serialized by this lock, so adding bio to the
lists (add_stripe_bio()) and removing bio from the lists (like
ops_run_biofill()) not race.
If bio in ->read, ->written ... list are not shared by multiple stripes, we
don't need any lock to protect ->read, ->written, because STRIPE_ACTIVE will
protect them. If the bio are shared, there are two protections:
1. bi_phys_segments acts as a reference count
2. traverse the list uses r5_next_bio, which makes traverse never access bio
not belonging to the stripe
Let's have an example:
| stripe1 | stripe2 | stripe3 |
...bio1......|bio2|bio3|....bio4.....
stripe2 has 4 bios, when it's finished, it will decrement bi_phys_segments for
all bios, but only end_bio for bio2 and bio3. bio1->bi_next still points to
bio2, but this doesn't matter. When stripe1 is finished, it will not touch bio2
because of r5_next_bio check. Next time stripe1 will end_bio for bio1 and
stripe3 will end_bio bio4.
before add_stripe_bio() addes a bio to a stripe, we already increament the bio
bi_phys_segments, so don't worry other stripes release the bio.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Neil pointed out the bitmap write optimization in handle_stripe_clean_event()
is unnecessary, because the chance one stripe gets written twice in the mean
time is rare. We can always do a bitmap_startwrite when a write request is
added to a stripe and bitmap_endwrite after write request is done. Delete the
optimization. With it, we can delete some cases of device_lock.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Raid5 overrides bio->bi_phys_segments, accessing it is with device_lock hold,
which is unnecessary, We can make it lockless actually.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
release_stripe() is a place conf->device_lock is heavily contended. We take the
lock even stripe count isn't 1, which isn't required.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The value returned by "mddev_check_plug" is only valid until the
next 'schedule' as that will unplug things. This could happen at any
call to mempool_alloc.
So just calling mddev_check_plug at the start doesn't really make
sense.
So call it just before, or just after, queuing things for the thread.
As the action that happens at unplug is to wake the thread, this makes
lots of sense.
If we cannot add a plug (which requires a small GFP_ATOMIC alloc) we
wake thread immediately.
RAID5 is a bit different. Requests are queued for the thread and the
thread is woken by release_stripe. So we don't need to wake the
thread on failure.
However the thread doesn't perform certain actions when there is any
active plug, so it is important to install a plug before waking the
thread. So for RAID5 we install the plug *before* queuing the request
and waking the thread.
Without this patch it is possible for raid1 or raid10 to queue a
request without then waking the thread, resulting in the array locking
up.
Also change raid10 to only flush_pending_write when there are not
active plugs, just like raid1.
This patch is suitable for 3.0 or later. I plan to submit it to
-stable, but I'll like to let it spend a few weeks in mainline
first to be sure it is completely safe.
Signed-off-by: NeilBrown <neilb@suse.de>
There isn't locking setting STRIPE_DELAYED and STRIPE_PREREAD_ACTIVE bits, but
the two bits have relationship. A delayed stripe can be moved to hold list only
when preread active stripe count is below IO_THRESHOLD. If a stripe has both
the bits set, such stripe will be in delayed list and preread count not 0,
which will make such stripe never leave delayed list.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We may not be able to fix a bad block if:
- the array is degraded
- the over-write fails.
In these cases we currently eject the device, but we should
record a bad block if possible.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Having the 'name' arg optional and defaulting to the current
personality name is no necessary and leads to errors, as when
changing the level of an array we can end up using the
name of the old level instead of the new one.
So make it non-optional and always explicitly pass the name
of the level that the array will be.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit 43220aa0f2
md/raid5: fix a hang on device failure.
fixed a hang, but introduced a refcounting in-balance so
that if the presence of bad-blocks ever caused an rdev to
be 'blocked' we would increment the refcount on the rdev and
never decrement it.
So added the needed rdev_dec_pending when md_wait_for_blocked_rdev
is not called.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In ops_run_io(), the call to md_wait_for_blocked_rdev will decrement
nr_pending so we lose the reference we hold on the rdev.
So atomic_inc it first to maintain the reference.
This bug was introduced by commit 73e92e51b7
md/raid5. Don't write to known bad block on doubtful devices.
which appeared in 3.0, so patch is suitable for stable kernels since
then.
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In chunk_aligned_read() we are adding data_offset before calling
is_badblock. But is_badblock also adds data_offset, so that is bad.
So move the addition of data_offset to after the call to
is_badblock.
This bug was introduced by commit 31c176ecdf
md/raid5: avoid reading from known bad blocks.
which first appeared in 3.0. So that patch is suitable for any
-stable kernel from 3.0.y onwards. However it will need minor
revision for most of those (as the comment didn't appear until
recently).
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If a RAID5 has both a failed device and a device marked as
'WantReplacement', then we should preferentially replace the failed
device.
However the current code replaces whichever is found first.
So split into 2 loops, check fail failed/missing first, and only check
for WantReplacement if nothing is failed or missing.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
After a reshape which reduced the number of devices we need
to disconnect the extra devices.
The code for this doesn't currently handle 'replacement' devices.
It is very unlikely that such devices will be present, but it is
safest to handle them anyway.
So simplify the handling. Just clear In_sync and leave it
to remove_and_add_spaces (which will be called soon) to do
the real works.
Signed-off-by: NeilBrown <neilb@suse.de>
We always should have allowed this. A raid5 reshape doesn't change
the size of the bitmap, so not need to restrict it.
Also add a test to make sure we don't try to start a reshape on a
failed array.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that bitmaps can be resized, we can allow an array to be resized
while the bitmap is present.
This only covers resizing that involves changing the effective size
of member devices, not resizing that changes the number of devices.
Signed-off-by: NeilBrown <neilb@suse.de>
REQ_SYNC is ignored in current raid5 code. Block layer does use it to do
policy,
for example ioscheduler. This patch adds it.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
