Prior to this patch, the code would happily trigger TX on some ports
before having a chance of reading the RX buffer from the rest of them.
When no flow control was used, this led to RX buffer overruns and
therefore lost data under certain circumstances.
I was able to reproduce this with MAX14830 (that's a quad channel one)
and a simple daisy-chain of RX and TX ports on the eval board:
- TX0 -> RX1
- TX1 -> RX2
- TX2 -> RX3
- TX3 -> RX0
I was testing this by transferring 2MB of data at 115200 baud via each
port. I used a Solidrun Clearfog Base (Armada 388) which was talking to
the UART over an SPI bus clocked at 26MHz (the chip's maximum). Without
this patch, I would always get a "Possible RX FIFO overrun" in dmesg,
and fewer-than-expected amount of bytes received over ttyMAX0. Results
on ttyMAX{1,2,3} tended to be correct all the time, even without the
previous patches in this series and with PIO SPI transfers ("indirect
mode" as the Marvell datasheet calls it), so I assume that heavy
congestion is needed in order to reproduce this.
A drawback of this patch is that the throughput gets reduced "a bit".
Previously, a 115200 baud resulted in about 11.2kBps throughput as
reported by a simple `pv`. With this patch, the throughput of four
parallel streams is roughly 7kBps each, and 9kBps for three streams.
There is no slowdown for one or two parallel streams.
Situation is worse if bytes are being read one-by-one (such as if the
userspace wants to perform parity/framing/break checking) and therefore
without the batched reads.
With just this patch and no other modifications on top of 4.14, I was
only getting roughly 3.6kBps with four parallel streams. The
single-stream performance was the same, and I was seeing about 7.2kBps
with two parallel streams. `perf top` said that a substantial amount of
time was spent in `finish_task_switch`, `_raw_spin_unlock_irqrestore`
and `__timer_delay`.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware has a 128 byte RX FIFO buffer for each independent UART.
Previously, the code was always reading that byte-by-byte via
independent SPI transactions and the associated overhead. In practice,
this led to up to eight bytes over SPI for just one byte in the UART's
RX FIFO:
- reading the global IRQ register (two bytes, one for command, the other
for data)
- reading one UART's ISR (again two bytes)
- reading the byte count (two bytes yet again)
- finally, reading one byte of the FIFO via another two-byte transaction
We cannot always use a batched read. If the TTY is set to intercept
break conditions or report framing or parity errors, then it is required
to check the Line Status Register (LSR) for each byte which is read from
the RX FIFO. The documentation does not show a way of doing that in a
single SPI transaction; registers 0x00 and 0x04 are separate.
In my testing, this is no silver bullet. I was feeding 2MB of random
data over four daisy-chaned UARTs of MAX14830, and this is the
distribution that I was getting:
- R <= 1: 7437322
- R <= 2: 162093
- R <= 4: 4093
- R <= 8: 4196
- R <= 16: 645
- R <= 32: 165
- R <= 64: 58
- R <= 128: 0
For a reference, batching the write operations works much better:
- W <= 1: 2664
- W <= 2: 1305
- W <= 4: 627
- W <= 8: 371
- W <= 16: 121
- W <= 32: 68
- W <= 64: 33
- W <= 128: 63139
That's probably because this HW/SW combination (Clearfog Base, Armada
388) is probably "good enough" to react to the chip's IRQ "fast enough"
most of the time. Still, I was getting RX overruns every now and then.
In future, I plan to improve this by letting the RX FIFO be filled a
little more (the chip has support for that and also for a "stale
timeout" to prevent additional starvation).
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transmit register supports batched writes. The key is simply to keep
sending additional bytes up to the FIFO size in the same SPI
transaction with the CS pin still being held low.
This duplicates the regmap infrastructure to a certain extent. There are
some provisions for multiple writes in there, but there does not appear
to be any support for those writes which are destined to the *same*
register (and also no standard for SPI bus transfers of these, anyway).
This patch does not solve every case (if the UART xmit circular buffer
wraps around, we're still doing two SPI transactions), but at least
it's not one-byte-per-transaction anymore.
This change does not touch the receive path at this time. Doing that in
the generic case appears to be impossible in the general case, because
the chips' status register contains data about the *current* byte in the
HW's Rx FIFO. We cannot read these two registers in one go,
unfortunately.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to my chip's datasheet [1], the IRQ output is an open
collector pin which is suitable for sharing with other chips. The chip
also has a register which indicates which UART performed a change and
the driver checks that register already, so we have everything what is
needed to effectively share the IRQ GPIO.
[1] https://datasheets.maximintegrated.com/en/ds/MAX14830.pdf
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As suggested by Russell King, a driver should not really care about bits
such as the interrupt polarity or whether it is edge- or level-
triggered. The reasons for that include:
- an upstream IRQ controller which cannot support edge- or
level-triggered interrupts,
- board design with a built-in inverter
The interrupt type is being already specified by the Device Tree,
anyway. Other drivers (gpio/gpio-tc3589x.c for example) already work in
this way, delegating the proper IRQ line setup to the DT and not
specifying anything by hand.
Also, there's no reason to have the IRQ flags split between two places.
The SPI probing is the only entry point anyway.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `max310x_spi_probe` function attempted to setup the GPIO bits before
the corresponding structs for each serial port were initialized. If the
DTS file specified a GPIO hog, this led to a crash because the GPIO
stack ended up calling `max310x_gpio_direction_output` which referenced
uninitialized memory:
[<c04598c0>] (max310x_gpio_direction_output) from [<c03f5a2c>] (_gpiod_direction_output_raw+0x94/0x2d4)
[<c03f5a2c>] (_gpiod_direction_output_raw) from [<c03f991c>] (gpiod_hog+0x6c/0x154)
[<c03f991c>] (gpiod_hog) from [<c03fa2d8>] (of_gpiochip_add+0x28c/0x444)
[<c03fa2d8>] (of_gpiochip_add) from [<c03f6b2c>] (gpiochip_add_data+0x4f8/0x760)
[<c03f6b2c>] (gpiochip_add_data) from [<c03f6dd4>] (devm_gpiochip_add_data+0x40/0x7c)
[<c03f6dd4>] (devm_gpiochip_add_data) from [<c0459fec>] (max310x_spi_probe+0x530/0x894)
[<c0459fec>] (max310x_spi_probe) from [<c0503294>] (spi_drv_probe+0x7c/0xac)
[<c0503294>] (spi_drv_probe) from [<c046628c>] (driver_probe_device+0x234/0x2e8)
[<c046628c>] (driver_probe_device) from [<c0464890>] (bus_for_each_drv+0x60/0x94)
[<c0464890>] (bus_for_each_drv) from [<c0465f78>] (__device_attach+0xb0/0x114)
[<c0465f78>] (__device_attach) from [<c0465548>] (bus_probe_device+0x84/0x8c)
[<c0465548>] (bus_probe_device) from [<c0463a00>] (device_add+0x3f4/0x580)
[<c0463a00>] (device_add) from [<c0504164>] (spi_add_device+0x9c/0x134)
[<c0504164>] (spi_add_device) from [<c0504c18>] (spi_register_controller+0x484/0x910)
[<c0504c18>] (spi_register_controller) from [<c0506ee0>] (orion_spi_probe+0x2f4/0x3b4)
[<c0506ee0>] (orion_spi_probe) from [<c0467dac>] (platform_drv_probe+0x50/0xb0)
[<c0467dac>] (platform_drv_probe) from [<c046628c>] (driver_probe_device+0x234/0x2e8)
[<c046628c>] (driver_probe_device) from [<c04663f8>] (__driver_attach+0xb8/0xbc)
[<c04663f8>] (__driver_attach) from [<c04647e8>] (bus_for_each_dev+0x68/0x9c)
[<c04647e8>] (bus_for_each_dev) from [<c046574c>] (bus_add_driver+0x104/0x210)
[<c046574c>] (bus_add_driver) from [<c0466f14>] (driver_register+0x78/0xf4)
[<c0466f14>] (driver_register) from [<c0101bdc>] (do_one_initcall+0x44/0x168)
[<c0101bdc>] (do_one_initcall) from [<c0a00dc0>] (kernel_init_freeable+0x140/0x1cc)
[<c0a00dc0>] (kernel_init_freeable) from [<c078c590>] (kernel_init+0x8/0x108)
[<c078c590>] (kernel_init) from [<c0107a50>] (ret_from_fork+0x14/0x24)
This can be easily fixed by moving the corresponding code below. And
because the UARTs are already there by the time we reach this point, the
`goto` needs changing so that more stuff is freed. (I have not tested
this error path.)
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all tty files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/tty files files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New IC MAX14830 has 0xB4 silicon revision ID.
This patch adds support for such ICs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dev.of_node is not NULL, we also need to set IRQF_TRIGGER_FALLING
flag, otherwise it may cause uncertain interrupts.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes assignment of port line automatically,
so now user allow to use several MAX310X chips.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves UART registration at module_init initcall,
so this should helps to add multiple chip support in the future.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use resource managed functions devm_gpiochip_add_data() to make
error & exit path a bit simpler.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RS485 IOCTLs uses spinlocks, so move regmap functions into a separate
work queue.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to unify all the rs485 ioctl handling
Use the implementation of TIOC[GS]RS485 ioctl handling on serial_core.
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e676253b19 ("serial/8250: Add support for RS485 IOCTLs") added
references to TIOC[SG]RS48 on 8250_core.c. This change triggered the
need to define them in all the arches that uses tty/serial.
This made #ifdef TIOC[SG]RS48 obsolete.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch allows to read the REV_ID register in SPI mode and consequently
to properly detect the max3109. Indeed in SPI mode, this register is only
accessible by using indirect addressing.
Signed-off-by: Gregory Hermant <gregory.hermant@calao-systems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.
SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
"If IGNBRK is set, a break condition detected on input shall be ignored;
that is, not put on the input queue and therefore not read by any
process."
Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.
Affected drivers:
8250 - all
serial_txx9
mfd
amba-pl010
amba-pl011
atmel_serial
bfin_uart
dz
ip22zilog
max310x
mxs-auart
netx-serial
pnx8xxx_uart
pxa
sb1250-duart
sccnxp
serial_ks8695
sirfsoc_uart
st-asc
vr41xx_siu
zs
sunzilog
fsl_lpuart
sunsab
ucc_uart
bcm63xx_uart
sunsu
efm32-uart
pmac_zilog
mpsc
msm_serial
m32r_sio
Unaffected drivers:
omap-serial
rp2
sa1100
imx
icom
Annotated for fixes:
altera_uart
mcf
Drivers without break detection:
21285
xilinx-uartps
altera_jtaguart
apbuart
arc-uart
clps711x
max3100
uartlite
msm_serial_hs
nwpserial
lantiq
vt8500_serial
Unknown:
samsung
mpc52xx_uart
bfin_sport_uart
cpm_uart/core
Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag'
Reported-by: Ivan <athlon_@mail.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cris allmodconfig:
drivers/tty/serial/max310x.c: In function 'max310x_ioctl':
drivers/tty/serial/max310x.c:885:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
drivers/tty/serial/max310x.c:916:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a temporary solution to fix following issue:
config: make ARCH=alpha allyesconfig
All error/warnings:
drivers/tty/serial/max310x.c: In function 'max310x_ioctl':
>> drivers/tty/serial/max310x.c:905:7: error: 'TIOCSRS485' undeclared (first use in this function)
drivers/tty/serial/max310x.c:905:7: note: each undeclared identifier is reported only once for each function it appears in
>> drivers/tty/serial/max310x.c:906:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
>> drivers/tty/serial/max310x.c:929:7: error: 'TIOCGRS485' undeclared (first use in this function)
>> drivers/tty/serial/max310x.c:938:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e3c6ea9b1b as it
didn't help anything, and caused more problems than expected.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
config: x86_64-randconfig-x006 (attached as .config)
All warnings:
drivers/tty/serial/max310x.c: In function 'max310x_probe':
>> drivers/tty/serial/max310x.c:1240:1: warning: label 'out_uart' defined but not used [-Wunused-label]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
config: make ARCH=alpha allyesconfig
All error/warnings:
drivers/tty/serial/max310x.c: In function 'max310x_ioctl':
>> drivers/tty/serial/max310x.c:905:7: error: 'TIOCSRS485' undeclared (first use in this function)
drivers/tty/serial/max310x.c:905:7: note: each undeclared identifier is reported only once for each function it appears in
>> drivers/tty/serial/max310x.c:906:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
>> drivers/tty/serial/max310x.c:929:7: error: 'TIOCGRS485' undeclared (first use in this function)
>> drivers/tty/serial/max310x.c:938:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds devicetree support for the MAX310X serial driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes some unused definitions from driver code and
sort #includes alphabetically.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for RS-485 (TIOCSRS485/TIOCGRS485) IOCTLs.
As a result this patch eliminate private driver header.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always register GPIOs and use dynamic GPIO ID assignment.
This is no much worth if GPIOs is not used, but helps remove
private driver header and add DT support in the future.
Additionally, patch adds missing uart_unregister_driver()
call if probe() fails.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes "frequency" parameter from MAX310X platform_data
and uses CLK API for getting clock. Clock type (XTAL/OSC) is
determined by clk name.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch move all SPI-dependent stuff in one place. This include move
PM-function definitions out of CONFIG_SPI_MASTER and move regmap
initialization out of common probe into CONFIG_SPI_MASTER which
may help to add I2C support in the future for this driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes excess IRQ checks at driver probe().
IRQ validation is already provided by request_threaded_irq().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces loopback mode support from platform data to
dynamic setup with TIOCMSET ioctl.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial core calls set_termios() after port startup, so there are
no reason to setup port twice.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These callbacks were previously used for the IC power initialization.
If this initialization will be needed in the future, it should be
implemented with the regulator API.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provide more precisely setup of baud rate generator.
If the result of division has a remainder, we use the multiplier
for the base frequency. Additionally, we report result baud rate
back to serial core.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These aren't necessary after switch and while blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes wrong dev_pm_ops which caused by commit:
serial: max310x: Driver rework.
CC drivers/tty/serial/max310x.o
LD drivers/video/fb.o
CC drivers/w1/slaves/w1_ds2433.o
CC drivers/w1/slaves/w1_ds2760.o
CC drivers/xen/balloon.o
CC drivers/video/backlight/adp8870_bl.o
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.suspend') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.resume') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.freeze') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.thaw') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.poweroff') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.restore') [enabled by default]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for MAX14830 (advanced quad universal asynchronous
receiver-transmitter) into max310x driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for MAX3109 (advanced dual universal asynchronous
receiver-transmitter) into max310x driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch rework max310x driver.
Major changes have been made:
- Prepare driver to support ICs with more than one UART.
- Prepare driver to support work with I2C-bus.
The patch changes almost every function and can not be divided into parts.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_pm_ops instead of the deprecated legacy suspend/resume for the
max310x driver.
Cc: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
