Otherwise it just contains random memory.
Issue detected by cppcheck.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The commit "Not all systems expose a firmware or platform mechanism for
changing the backlight intensity on i915, so add native driver support"
adds calls to intel_panel_setup_backlight() from intel_{lvds,dp}_init
so do not call it again from intel_setup_outputs().
BugLink: http://bugs.launchpad.net/bugs/831542
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
ACKed-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel:
drm/i915: set GFX_MODE to pre-Ivybridge default value even on Ivybridge
Prior to Ivybridge, the GFX_MODE would default to 0x800, meaning that
MI_FLUSH would flush the TLBs in addition to the rest of the caches
indicated in the MI_FLUSH command. However starting with Ivybridge, the
register defaults to 0x2800 out of reset, meaning that to invalidate the
TLB we need to use PIPE_CONTROL. Since we're not doing that yet, go
back to the old default so things work.
v2: don't forget to actually *clear* the new bit
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The clock gating functions are only assigned under KMS, so don't try
to call them under UMS.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Disable this feature when KMS is not running by setting the
driver->get_vblank_timestamp function pointer to NULL.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com>
Tested-by: Michel Alexandre Salim <salimma@fedoraproject.org>
Tested-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
We ought to be calling this from our DPMS routines as well as global
state may change and we need to enable/disable clocks. So split out the
code in preparation for further changes.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
IVB uses the same interrupt reg layout as SNB, so add an IS_GEN7 to the
interrupt debugfs file.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Just an extra parameter which isn't actually needed.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
CPT pipe select is different from previous generations (using two bits
instead of one). All of the paths from intel_disable_pch_ports were
not making this distinction.
Mode setting with pipe A turned off would then also force all outputs
on pipe B to get turned off as the disable code would mistakenly
decide that all of these outputs were on pipe A and turn them off.
This is an extension of the CPT DP disable fix (why didn't I fix this then?)
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There's no reason to relock them; it just makes operations more
complex. This fixes DPMS where the panel registers were locked making
the disable not work.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
During mode setting, check to make sure the panel power sequencing has
completed before doing further operations on the device. This
uncovered errors with DPMS not turning the device off as it was left locked.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Expose the SNB+ cache sharing policy register in debugfs. The new file,
i915_cache_sharing, has 4 values, 0-3, with 0 being "max uncore
resources" and 3 being the minimum. Exposing this control should make
benchmarking easier and help us choose a good default.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This makes it easier to add support for other infoframes (e.g. SPD,
vendor specific).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Jesse Barnes and I found a couple of issues where incorrect mode
setting would cause problems with RC6 enabled. We're hopeful that
fixing those will resolve the outstanding issues with a few machines
that had trouble before 3.0 with rc6.
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Francesco Allertsen <fallertsen@gmail.com>
Cc: Ted Phelps <phelps@gnusto.com>
Cc: Gu Rui <chaos.proton@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38567
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=38332
Signed-off-by: Keith Packard <keithp@keithp.com>
This reverts commit 97cdd71010.
Clearing the dpcd data means that if the fetch fails, any previous
data will be lost. On eDP, this is no fun as we only fetch dpcd at
init time, so the memset will destroy that the next time through.
Before initiating a new read or write on the DP AUX channel, wait for
any outstanding activity to complete. This may happen during normal
retry behavior. If the wait fails (i.e. after 1ms the AUX channel is
still busy) dump a backtrace to make the caller easier to spot.
v2: use msleep instead, and timeout after 3ms (only ever saw 1 retry
with msleep in testing)
v3: fix backtrace check to trigger if the 3ms wait times out
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=38136.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The EDID parser will zero out the bpc value, and the driver needs to handle
that case. In our picker, we'll just ignore 0 values as far as bpp
picking goes.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=39323.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
At least on a Lenovo X220 the HPD bits of this are enabled at boot but
cleared after resume, which means plug interrupts stop working.
This also happens to fix DP displays re-lighting on resume. I'm quite
certain that's an accident: the first DP link train inevitably fails on
that machine, and it's only serendipity that we're getting multiple plug
interrupts and the second train works. But I shall take my victories
where I get them.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
These bits moved around on SNB and above.
v2: again with the git send-email fail
v3: add macros for getting per-pipe override & enable bits
v4: enable phase sync pointer on SNB and IVB configs as well
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Using the new quirk added to support disabling SSC on Lenovo U160
(#36656, commit 435793dfb8), also register
the Vaio as a special case and disable SSC for it.
This patch fixes#34437 on fdo bugzilla:
https://bugs.freedesktop.org/show_bug.cgi?id=34437
Signed-off-by: Michel Alexandre Salim <salimma@fedoraproject.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
If a mode set fails we may get a message from drm_crtc_helper if we're lucky,
but it won't tell us anything about *why* we failed to set a mode. So
add a few DRM_ERRORs for the cases that shouldn't happen so we can debug
things more easily.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Mainly for use in debugging and benchmarking, this file allows the user
to control the max frequency used by the GPU. Frequency may still vary
based on workload (if the frequency is set to higher than the minimum)
but won't go over the newly set value.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The Dell OptiPlex FX170 claims to have LVDS, but doesn't.
Signed-off-by: Pieterjan Camerlynck <pieterjan.camerlynck@gmail.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Failing to pin a scanout buffer will most likely lead to a black
screen, so if the GPU is wedged, then just let the pin happen and hope
that things work out OK.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
On Ironlake and above, we have per-transcoder DIP registers, so use them
for sending DIPs like AVI infoframes on ILK and above.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
CB tuning is needed to handle potential process variations that might
cause clock jitter for certain PLL settings. However, we were setting
it incorrectly since we were using the wrong M value as a check (M1 when
we needed to use the whole M value). Fix it up, making my HDMI
attached display a little prettier (used to have occasional dots crawl
across the display).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Writes to the plane control register are buffered in the chip until a
write to the DSPADDR (pre-965) or DSPSURF (post-965) register occurs.
This patch adds flushes in:
intel_enable_plane
gen6_init_clock_gating
ivybridge_init_clock_gating
Signed-off-by: Keith Packard <keithp@keithp.com>
After writing to the plane control reg we need to write to the surface
reg to trigger the double buffered register latch. On previous
chipsets, writing to DSPADDR was enough, but on ILK+ DSPSURF is the reg
that triggers the double buffer latch.
v2: write DSPADDR too to cover pre-965 chipsets
v3: use flush_display_plane instead, that's what it's for
v4: send the right patch
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
On CougarPoint and PantherPoint PCH chips, the timing generator may fail
to start after DP training completes. This is due to a bug in the
FDI autotraining detect logic (which will stall the timing generator and
re-enable it once training completes), so disable it to avoid silent DP
mode setting failures.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This corrects the DPMS mode tracking so that the DPMS code will
actually turn the CRTC off the next time the screen saves.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reverts commit 885a50147f.
We actually *do* need to track DPMS state so that on hotplug, we don't
retrain the link until DPMS is disabled.
However, that code had avery small bug -- it wouldn't set the
dpms_mode at mode set time, and so link retraining would not actually
occur on monitor hotplug until the monitor had gone through a DPMS
off/DPMS on cycle.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Andrew Lutomirski <luto@mit.edu>
Display port pipe selection on CPT is not done with a bit in the
output register, rather it is controlled by a couple of bits in the
separate transcoder register which indicate which display port output
is connected to the transcoder.
This patch replaces the simplistic macro DP_PIPE_ENABLED with the
rather more complicated function dp_pipe_enabled which checks the
output register to see if that is enabled, and then goes on to either
check the output register pipe selection bit (on non-CPT) or the
transcoder DP selection bits (on CPT).
Before this patch, any time the mode of pipe A was changed, any
display port outputs on pipe B would get disabled as
intel_disable_pch_ports would ensure that the mode setting operation
could occur on pipe A without interference from other outputs
connected to that pch port
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Eliminates an open-coded read and also gains the retry behaviour of
intel_dp_get_dpcd, which seems like a good idea.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
This describes the function better, allowing it to be used where the
DPCD value is relevant.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
This uses the common dpcd reading routine, i915_dp_detect_common,
instead of open-coding a call to intel_dp_aux_native_read. Besides
reducing duplicated code, this also gains the read retries which
may be necessary when a cable is first plugged back in and the link
needs to be retrained.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
drm_helper_hpd_irq_event queues another work proc to go and deliver
the user-space event, and that function also wants to hold the config
mutex, so we shouldn't hold the mutex across the
drm_helper_hpd_irq_event call.
Signed-off-by: Keith Packard <keithp@keithp.com>
The docs say the port has to come on in training pattern 1; at this
point, though, ->DP is in normal mode. The intent here is to wait
until the port is in fact sending data, but that doesn't happen since
we've broken the sequence the hardware expects, and the vblank wait will
time out and kvetch in the log.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The DP spec says training patterns 1 and 2 are to be sent non-scrambled,
and the GPU docs claim that happens (or at least, there's no explicit
scrambling control). But the sink may be confused if we don't
explicitly tell it what we're doing, so play it safe.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Consider a 1600x900 panel, upscaling a 1360x768 mode, full-aspect. The
old math would give you:
scaled_width = 1600 * 768; /* 1228800 */
scaled_height = 1360 * 900; /* 1224000 */
if (scaled_width > scaled_height) { /* pillarbox, and true */
width = 1224000 / 768; /* int(1593.75) = 1593 */
x = (1600 - 1593 + 1) / 2; /* 4 */
y = 0;
height = 768;
} /* ... */
This is broken. The total width of scanout would then be 1593 + 4 + 4,
or 1601, which is wider than the panel itself. The hardware very
dutifully implements this, and you end up with a black 45° diagonal from
the top-left corner to the bottom edge of the screen. It's a cool
effect and all, but not what you wanted. Similar things happen for the
letterbox case.
The problem is that you have an integer number of pixels, which means
it's usually impossible to upscale equally on both axes. 1360/768 is
1.7708, 1600/900 is 1.7777. Since we're constrained on the one axis,
the other one wants to come out as an even number of pixels (the panel
is almost certainly even on both axes, and the x/y offsets will be
applied on both sides). In the math above, if 'width' comes out even,
rounding down is correct; if it's odd, you'd rather round up. So just
increment width/height in those cases.
Tested on a Lenovo T500 (Ironlake).
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-By: Daniel Manrique <daniel.manrique@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38851
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
Hotplug detection is a mode setting operation and must hold the
struct_mutex or risk colliding with other mode setting operations.
In particular, the display port hotplug function attempts to re-train
the link if the monitor is supposed to be running when plugged back
in. If that happens while mode setting is underway, the link will get
scrambled, leaving it in an inconsistent state.
This is a special case -- usually the driver mode setting entry points
are covered by the upper level DRM code, but in this case the function
is invoked as a work function not under the control of DRM.
Signed-off-by: Keith Packard <keithp@keithp.com>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It's not clear what a sink would do if you wrote zero to this register -
which I guess would mean "I don't support any channel encodings, good
luck" - but let's not find out.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
