Add a debounce parameter to the mmc_gpio_request_cd() function that
enables GPIO debouncing when set to a non-zero value. This can be used
by MMC host drivers to enable debouncing on the card detect signal.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes a compiler warning:
drivers/mmc/host/tmio_mmc_pio.c: In function 'tmio_mmc_power_on':
drivers/mmc/host/tmio_mmc_pio.c:798:19: warning: ignoring return value of
'regulator_enable', declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This fixes two reported problems:
1. after a system resume the controller isn't functioning until a command
runs on a timeout and a controller reset is performed.
2. if a card is ejected during a running write operation, its re-insertion
isn't detected.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Reported-by: Nguyen Hong Ky <nh-ky@jinso.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Tested-by: Nguyen Hong Ky <nh-ky@jinso.co.jp>
Signed-off-by: Chris Ball <cjb@laptop.org>
With MMC clock gating enabled the MMC core currently calls MMC host driver's
.set_ios() method with .power_mode == MMC_POWER_ON and the clock value set
either to 0 or to the target rate. The tmio MMC driver then wrongly
translates the latter calls to card slot power-on requests, even when the
slot already was on. This patch fixes the driver to avoid needlessly
incrementing power-supplying regulator's use count.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When resuming, the tmio_mmc_host_resume() function is run when the
controller might still be powered down. Issuing a reset command to it at
that time has no effect. This patch postpones resetting the controller
until the first powering-up .set_ios() call.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some SD/MMC interfaces use 2 power regulators: one to power the card itself
(Vcc) and another one to pull signal lines up (VccQ). In case of eMMC and
UHS SD cards the regulators also have to be configured to supply different
voltages. The preferred order of turning supply power on and off is to
turn Vcc first on and last off.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add parsing of common and driver-specific DT bindings to the tmio-mmc
MMC host driver and the sh_mobile_sdhi interface layer.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
tmio-mmc platform flags can be set by various means, including caller
drivers and device-tree bindings, therefore it is better to only check
them in the tmio-mmc driver proper, not in caller drivers themselves.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since slot-gpio uses devm_* managed functions in mmc_gpio_request_cd()
now, we can remove those mmc_gpio_free_cd() call from host drivers'
.probe() error path and .remove().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tmio-mmc driver is already using the generic GPIO CD handler in IRQ
mode. This patch adds support for CD polling mode and also checks for
availability of a WP GPIO.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allow tmio mmc glue drivers to pass mmc_host::caps2 flags down to
the mmc layer.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently the TMIO MMC driver derives the OCR mask from the platform data
and uses a platform callback to turn card power on and off. This patch adds
regulator support to the driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Every time the clock is enabled after possibly being disabled, we have
to re-read its frequency and update our configuration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
We don't have to force-enable MMC interrupts in our .probe() method,
mmc_add_host() will trigger card detection, that will enable all the
necessary interrupts.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The tmio_mmc_set_ios() function configures the MMC power, clock and bus
width. When the mmc core requests the driver to power off the card, we
inform runtime PM, that the controller can be suspended. This can lead
to the MSTP clock being turned off.
Writing to any 16-bit hardware registers with the MSTP clock off leads
to timeouts and errors being printed to the kernel log. This can occur
both when stopping the MMC clock and when configuring the bus width.
To fix this, stop the MMC clock before calling put_runtime_pm(), and
skip bus width configuration when power is off.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
GPIOs can be used in MMC/SD-card slots not only for hotplug detection, but
also to implement the write-protection pin. Rename cd-gpio helpers to
slot-gpio to make addition of further slot GPIO functions possible.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc.h defines macros for most frequently used MMC opcodes. Use them instead
of hard-coded numbers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sdio_irq_enabled member of struct tmio_mmc_host is a left-over from the
previously removed SDIO IRQ workaround. It is no longer needed and can now
be removed too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The controller power status flag does not have to be accessed from the
hot-plug detection code any more, it can now be removed from the platform
data and put in the controller private struct.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the platform specifies the TMIO_MMC_HAS_COLD_CD flag, use the generic
MMC GPIO card hotplug helper.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The condition, whether we have to use the native TMIO card hotplug
detection interrupt, is rather complex, it is better to only calculate it
once and store in the private data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
If TMIO MMC is used in polling mode, or the card is non-removable, or
card-detection is performed, using an external interrupt, there is no
need to enable controller native card hotplug interrupts.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
* pm-qos:
sh_mmcif / PM: Use PM QoS latency constraint
tmio_mmc / PM: Use PM QoS latency constraint
PM / QoS: Make it possible to expose PM QoS latency constraints
Make tmio_mmc call dev_pm_qos_expose_latency_limit() to expose
the PM QoS latency limit to user space and specify the initial
value of it as 100 microseconds.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
When DMA is in use and the card is ejected during IO, DMA transfers have to
be terminated, otherwise the dmaengine driver fails to operate properly,
when the card is re-inserted.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch regroups the code slightly, adds documentation and allows
the rtpm counter of MMC_CAP_NEEDS_POLL devices to reach 0 again.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
[g.liakhovetski@gmx.de: restore pm_runtime_get_noresume()]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Do not power down the card in .set_ios(), unless MMC_POWER_OFF is
requested. This fixes the SDHI functionality on ecovec.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
All the files using printk function for displaying kernel messages
in the mmc driver have been replaced with corresponding macro.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Provide separate interrupt handlers which may be used by platforms where
SDHI has three interrupt sources.
This patch also removes the commented-out handling of CRC and other errors.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
This avoids the need to look up the masks each time an interrupt is handled.
As suggested by Guennadi.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently the tmio-mmc driver contains a recursive runtime PM method
invocation, which leads to a deadlock on a mutex. Avoid it by taking
care not to request DMA too early.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch uses runtime PM to allow the system to power down the MMC
controller, when the MMC closk is switched off.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Calling mmc_request_done() under a spinlock with interrupts disabled
leads to a recursive spin-lock on request retry path and to
scheduling in atomic context. This patch fixes both these problems
by moving mmc_request_done() to the scheduler workqueue.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
There is a race condition in the tmio_mmc_irq() interrupt handler,
caused by the presence of a while loop, which results in warnings of
spurious interrupts. This was found on an HP iPAQ hx4700 whose HTC
ASIC3 reportedly incorporates the Toshiba TC6380AF controller.
Towards the end of a multiple read (CMD18) operation the handler clears
the final RXRDY status bit in the first loop iteration, sees the DATAEND
status bit at the bottom of the loop, and so clears the DATAEND status
bit in the second loop iteration. However the DATAEND interrupt is still
queued in the system somewhere and can't be delivered until the handler
has returned. This second interrupt is then reported as spurious in the
next call to the handler. Likewise for single read (CMD17) operations.
And something similar occurs for multiple write (CMD25) and single write
(CMD24) operations, where CMDRESPEND and TXRQ status bits are cleared in
a single call.
In these cases the interrupt handler clears two separate interrupts when
it should only clear the one interrupt for which it was invoked. The fix
is to remove the while loop.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Move register access functions into a shared header.
Use sd_ctrl_write16 in tmio_mmc_dma.c:tmio_mmc_enable_dma().
Other than avoiding (trivial) open-coding, the motivation for
this is to allow platform-hooks in access functions to
be applied across all applicable accesses.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit b6147490e6 ("mmc: tmio: split core functionality, DMA and
MFD glue") broke handling of the TMIO_MMC_WRPROTECT_DISABLE flag by
the tmio-mmc driver. This patch restores the original behaviour.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The TMIO MMC controller cannot be powered off to save power, when no
card is plugged in, because then it will not be able to detect a new
card-insertion event. On some implementations, however, it is
possible to switch to using another source to detect card insertion.
This patch adds support for such implementations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Move request_irq()/free_irq() from the shared code
in tmio_mmc.c into the SDHI/tmio specific portion
in sh_mobile_sdhi.c and tmio_mmc_pio.c.
This is ground work to allow us to adjust the SDHI
code with IRQ flags and number of interupt sources.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The MMC subsystem does not guarantee, that host driver .request() and
.set_ios() callbacks are serialised. Such concurrent calls, however,
do not have to be meaningfully supported, drivers just have to make
sure to avoid any severe problems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add runtime and system-wide power management to the TMIO MMC driver
in PIO and DMA modes, allowing it to properly save and restore its
state during system suspend. Runtime PM is very crude ATM, because
the controller has to be powered on all the time to detect card
hotplug events.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The aggressive clock gating for TMIO MMC patch has broken switching
interface power on, using MFD or platform callbacks. Restore the
ios->power_mode == MMC_POWER_UP && ios->clock == 0 case handling.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Also add TMIO_BBS.
This allows these defines to also be used by zboot.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The power-mode sequence on MMC is MMC_POWER_OFF -> MMC_POWER_UP ->
MMC_POWER_ON and not MMC_POWER_ON -> MMC_POWER_UP, as the driver currently
is implying.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDIO IRQs got unmasked on sh-mobile while writing to the
CTL_CLK_AND_WAIT_CTL register, because that register at address 0x138
is not implemented on those SoCs and writes to it overwrite the
register at address 0x38: CTL_SDIO_IRQ_MASK. Previous patches
eliminated access to register above 0xff on sh-mobile, so that this
work-around isn't needed anymore.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
