Pull virtio updates from Michael Tsirkin:
"virtio,vdpa,qemu_fw_cfg: features, cleanups, and fixes.
- partial support for < MAX_ORDER - 1 granularity for virtio-mem
- driver_override for vdpa
- sysfs ABI documentation for vdpa
- multiqueue config support for mlx5 vdpa
- and misc fixes, cleanups"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (42 commits)
vdpa/mlx5: Fix tracking of current number of VQs
vdpa/mlx5: Fix is_index_valid() to refer to features
vdpa: Protect vdpa reset with cf_mutex
vdpa: Avoid taking cf_mutex lock on get status
vdpa/vdpa_sim_net: Report max device capabilities
vdpa: Use BIT_ULL for bit operations
vdpa/vdpa_sim: Configure max supported virtqueues
vdpa/mlx5: Report max device capabilities
vdpa: Support reporting max device capabilities
vdpa/mlx5: Restore cur_num_vqs in case of failure in change_num_qps()
vdpa: Add support for returning device configuration information
vdpa/mlx5: Support configuring max data virtqueue
vdpa/mlx5: Fix config_attr_mask assignment
vdpa: Allow to configure max data virtqueues
vdpa: Read device configuration only if FEATURES_OK
vdpa: Sync calls set/get config/status with cf_mutex
vdpa/mlx5: Distribute RX virtqueues in RQT object
vdpa: Provide interface to read driver features
vdpa: clean up get_config_size ret value handling
virtio_ring: mark ring unused on error
...
Pull hyperv updates from Wei Liu:
- More patches for Hyper-V isolation VM support (Tianyu Lan)
- Bug fixes and clean-up patches from various people
* tag 'hyperv-next-signed-20220114' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
scsi: storvsc: Fix storvsc_queuecommand() memory leak
x86/hyperv: Properly deal with empty cpumasks in hyperv_flush_tlb_multi()
Drivers: hv: vmbus: Initialize request offers message for Isolation VM
scsi: storvsc: Fix unsigned comparison to zero
swiotlb: Add CONFIG_HAS_IOMEM check around swiotlb_mem_remap()
x86/hyperv: Fix definition of hv_ghcb_pg variable
Drivers: hv: Fix definition of hypercall input & output arg variables
net: netvsc: Add Isolation VM support for netvsc driver
scsi: storvsc: Add Isolation VM support for storvsc driver
hyper-v: Enable swiotlb bounce buffer for Isolation VM
x86/hyper-v: Add hyperv Isolation VM check in the cc_platform_has()
swiotlb: Add swiotlb bounce buffer remap function for HV IVM
This will enable cleanups down the road.
The idea is to disable cbs, then add "flush_queued_cbs" callback
as a parameter, this way drivers can flush any work
queued after callbacks have been disabled.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20211013105226.20225-1-mst@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (ufs, pm80xx, lpfc,
mpi3mr, mpt3sas, hisi_sas, libsas) and minor updates and bug fixes.
The most impactful change is likely the switch from GFP_DMA to
GFP_KERNEL in a bunch of drivers, but even that shouldn't affect too
many people"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (121 commits)
scsi: mpi3mr: Bump driver version to 8.0.0.61.0
scsi: mpi3mr: Fixes around reply request queues
scsi: mpi3mr: Enhanced Task Management Support Reply handling
scsi: mpi3mr: Use TM response codes from MPI3 headers
scsi: mpi3mr: Add io_uring interface support in I/O-polled mode
scsi: mpi3mr: Print cable mngnt and temp threshold events
scsi: mpi3mr: Support Prepare for Reset event
scsi: mpi3mr: Add Event acknowledgment logic
scsi: mpi3mr: Gracefully handle online FW update operation
scsi: mpi3mr: Detect async reset that occurred in firmware
scsi: mpi3mr: Add IOC reinit function
scsi: mpi3mr: Handle offline FW activation in graceful manner
scsi: mpi3mr: Code refactor of IOC init - part2
scsi: mpi3mr: Code refactor of IOC init - part1
scsi: mpi3mr: Fault IOC when internal command gets timeout
scsi: mpi3mr: Display IOC firmware package version
scsi: mpi3mr: Handle unaligned PLL in unmap cmnds
scsi: mpi3mr: Increase internal cmnds timeout to 60s
scsi: mpi3mr: Do access status validation before adding devices
scsi: mpi3mr: Add support for PCIe Managed Switch SES device
...
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core:
- Provide a new interface for affinity hints to provide a separation
between hint and actual affinity change which has become a hidden
property of the current interface
- Fix up the in tree usage of the affinity hint interfaces
Drivers:
- No new irqchip drivers!
- Fix GICv3 redistributor table reservation with RT across kexec
- Fix GICv4.1 redistributor view of the VPE table across kexec
- Add support for extra interrupts on spear-shirq
- Make obtaining some interrupts optional for the Renesas drivers
- Various cleanups and bug fixes"
* tag 'irq-core-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
irqchip/renesas-intc-irqpin: Use platform_get_irq_optional() to get the interrupt
irqchip/renesas-irqc: Use platform_get_irq_optional() to get the interrupt
irqchip/gic-v4: Disable redistributors' view of the VPE table at boot time
irqchip/ingenic-tcu: Use correctly sized arguments for bit field
irqchip/gic-v2m: Add const to of_device_id
irqchip/imx-gpcv2: Mark imx_gpcv2_instance with __ro_after_init
irqchip/spear-shirq: Add support for IRQ 0..6
irqchip/gic-v3-its: Limit memreserve cpuhp state lifetime
irqchip/gic-v3-its: Postpone LPI pending table freeing and memreserve
irqchip/gic-v3-its: Give the percpu rdist struct its own flags field
net/mlx4: Use irq_update_affinity_hint()
net/mlx5: Use irq_set_affinity_and_hint()
hinic: Use irq_set_affinity_and_hint()
scsi: lpfc: Use irq_set_affinity()
mailbox: Use irq_update_affinity_hint()
ixgbe: Use irq_update_affinity_hint()
be2net: Use irq_update_affinity_hint()
enic: Use irq_update_affinity_hint()
RDMA/irdma: Use irq_update_affinity_hint()
scsi: mpt3sas: Use irq_set_affinity_and_hint()
...
Pull block updates from Jens Axboe:
- Unify where the struct request handling code is located in the blk-mq
code (Christoph)
- Header cleanups (Christoph)
- Clean up the io_context handling code (Christoph, me)
- Get rid of ->rq_disk in struct request (Christoph)
- Error handling fix for add_disk() (Christoph)
- request allocation cleanusp (Christoph)
- Documentation updates (Eric, Matthew)
- Remove trivial crypto unregister helper (Eric)
- Reduce shared tag overhead (John)
- Reduce poll_stats memory overhead (me)
- Known indirect function call for dio (me)
- Use atomic references for struct request (me)
- Support request list issue for block and NVMe (me)
- Improve queue dispatch pinning (Ming)
- Improve the direct list issue code (Keith)
- BFQ improvements (Jan)
- Direct completion helper and use it in mmc block (Sebastian)
- Use raw spinlock for the blktrace code (Wander)
- fsync error handling fix (Ye)
- Various fixes and cleanups (Lukas, Randy, Yang, Tetsuo, Ming, me)
* tag 'for-5.17/block-2022-01-11' of git://git.kernel.dk/linux-block: (132 commits)
MAINTAINERS: add entries for block layer documentation
docs: block: remove queue-sysfs.rst
docs: sysfs-block: document virt_boundary_mask
docs: sysfs-block: document stable_writes
docs: sysfs-block: fill in missing documentation from queue-sysfs.rst
docs: sysfs-block: add contact for nomerges
docs: sysfs-block: sort alphabetically
docs: sysfs-block: move to stable directory
block: don't protect submit_bio_checks by q_usage_counter
block: fix old-style declaration
nvme-pci: fix queue_rqs list splitting
block: introduce rq_list_move
block: introduce rq_list_for_each_safe macro
block: move rq_list macros to blk-mq.h
block: drop needless assignment in set_task_ioprio()
block: remove unnecessary trailing '\'
bio.h: fix kernel-doc warnings
block: check minor range in device_add_disk()
block: use "unsigned long" for blk_validate_block_size().
block: fix error unwinding in device_add_disk
...
Pull SCSI fixes from James Bottomley:
"Three fixes, all in drivers. The lpfc one doesn't look exploitable,
but nasty things could happen in string operations if mybuf ends up
with an on stack unterminated string"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: vmw_pvscsi: Set residual data length conditionally
scsi: libiscsi: Fix UAF in iscsi_conn_get_param()/iscsi_conn_teardown()
scsi: lpfc: Terminate string in lpfc_debugfs_nvmeio_trc_write()
Add support for the io_uring interface in I/O-polled mode.
This feature is disabled in the driver by default. To enable the feature, a
module parameter "poll_queues" has to be set with the desired number of
polling queues.
When the feature is enabled, the driver reserves a certain number of
operational queue pairs for the poll_queues either from the available queue
pairs or creates additional queue pairs based on the operational queue
availability.
The Polling queues will have corresponding IRQ and ISR functions as similar
to default queues. However, the IRQ line is disabled by the driver for
poll_queues.
Link: https://lore.kernel.org/r/20211220141159.16117-22-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The IOC sends a Prepare for Reset Event to the host to prepare for a Soft
Reset. This event data has two reason codes:
1. Start - The host is expected to gracefully quiesce all I/O within
approximately 1 second.
2. Abort - The IOC is requesting to abort a previous Prepare for Reset
Event request. Normal I/O may be resumed.
Link: https://lore.kernel.org/r/20211220141159.16117-20-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enhance driver to gracefully handle discrepancies in certain key data sizes
between firmware update operations as mentioned below:
- The driver displays an error message and marks the controller as
unrecoverable if the firmware reports ReplyFrameSize that is greater
than the current ReplyFrameSize.
- If the firmware reports ReplyFrameSize greater than the current
ReplyFrameSize then the driver uses the current ReplyFrameSize while
copying the reply messages.
- The driver displays an error message and marks the controller as
unrecoverable if the firmware reports MaxOperationalReplyQueues less
than the currently allocated operational reply queues count.
- If the firmware reports MaxOperationalReplyQueues that is greater than
the currently allocated operational reply queue count then the driver
ignores the new increased value and uses the previously allocated number
of operational queues only.
- If the firmware reports MaxDevHandle greater than the previously used
MaxDevHandle value after a reset then the driver re-allocates the
'device remove pending bitmap' buffer with the newer size using
krealloc().
Link: https://lore.kernel.org/r/20211220141159.16117-18-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Detect asynchronous reset that occurred in the firmware by polling for
reset history bit of IOC status register is set and if that bit is set,
then the driver waits for the controller to become ready and then
re-initializes the controller.
Also reduce the time driver is waiting for the controller to acknowledge
the reset action after issuing a specific reset action to the
controller. The wait time is reduced from 510 seconds to 30 seconds. If the
controller didn't acknowledge a specific reset action within the time
interval then the driver marks the controller as unrecoverable instead of
retrying two more times prior to giving up.
Link: https://lore.kernel.org/r/20211220141159.16117-17-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver marks the controller as unrecoverable if there is an
asynchronous reset or fault during the initialization, reinitialization
post reset, and OS resume.
Enhance driver to retry the initialization, re-initialization, and resume
sequences for a maximum of 3 times if the controller became faulty or
asynchronously reset due to a firmware activation during the initialization
sequence.
Link: https://lore.kernel.org/r/20211220141159.16117-15-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Save snapdump and fault the controller with the given reason code if it is
already not in the fault or not in asynchronous reset. This ensures that
soft reset is issued from the watchdog thread. This will also be used to
handle initialization time faults/resets/timeout as in those cases
immediate soft reset invocation is not required.
Link: https://lore.kernel.org/r/20211220141159.16117-12-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following special handling is needed for UNMAP commands issued to NVMe
drives:
- On B0 boards, if the parameter list length is greater than 24 and not a
16-byte multiple, then truncate the parameter list length to a 16-byte
multiple.
- On A0 boards, if the parameter list length is greater than block
descriptor data length + 8, then truncate the parameter list length to
block descriptor data length + 8 value.
Link: https://lore.kernel.org/r/20211220141159.16117-10-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS4 Controller firmware exposes the SES devices in Managed PCIe Switch
as a PCIe Device Type SCSI Device
(MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_SCSI_DEVICE).
Driver is enhanced to handle this device type by:
- Exposing the device to the upper layers and
- Not updating any hardware sectors & virtual boundary settings as these
settings are needed only for NVMe devices.
Link: https://lore.kernel.org/r/20211220141159.16117-7-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Processing events such as PORTE_BROADCAST_RCVD may cause dependency issues
for runtime power management support. Such a problem would be that
handling a PORTE_BROADCAST_RCVD event requires that the host is resumed to
send SMP commands. However, in resuming the host, the phyup events
generated from re-enabling the phys are processed in the same workqueue as
the original PORTE_BROADCAST_RCVD event. As such, the host will never
finish resuming (as it waits for the phyup event processing), and then the
PORTE_BROADCAST_RCVD event can't be processed as the SMP commands are
blocked, and so we have a deadlock. Solve this problem by ensuring that
libsas keeps the host active until completely finished phy or port events,
such as PORTE_BYTES_DMAED. As such, we don't have to worry about resuming
the host for processing individual SMP commands in this example.
Link: https://lore.kernel.org/r/1639999298-244569-15-git-send-email-chenxiang66@hisilicon.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is possible that controller may become suspended between processing a
phyup interrupt and the event being processed by libsas. As such, we can't
ensure the controller is active when processing the phyup event - this may
cause the phyup event to be lost or other issues. To avoid any possible
issues, add pm_runtime_get_noresume() in phyup interrupt handler and
pm_runtime_put_sync() in the work handler exit to ensure that we stay
always active. Since we only want to call pm_runtime_get_noresume() for v3
hw, signal this will a new event, HISI_PHYE_PHY_UP_PM.
Link: https://lore.kernel.org/r/1639999298-244569-14-git-send-email-chenxiang66@hisilicon.com
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During the processing of event PORT_BYTES_DMAED, the driver queues work
DISCE_DISCOVER_DOMAIN and then flushes workqueue ha->disco_q. If a new
phyup event occurs during resuming the controller, the work
PORTE_BYTES_DMAED of new phy occurs before suspended phy's. The work
DISCE_DISCOVER_DOMAIN of new phy requires an active SAS controller (it
needs to resume SAS controller by function scsi_sysfs_add_sdev() and some
other functions such as function add_device_link()). However, the
activation of the SAS controller requires completion of work
PORTE_BYTES_DMAED of suspended phys while it is blocked by new phy's work
on ha->event_q. So there is a deadlock and it is released only after resume
timeout.
To solve the issue, defer works of new phys during suspend and queue those
defer works after SAS controller becomes active.
Link: https://lore.kernel.org/r/1639999298-244569-13-git-send-email-chenxiang66@hisilicon.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
