Eric Biggers pointed out that the orinoco driver pointed scatterlists
at the stack.
Fix it by switching from ahash to shash. The result should be
simpler, faster, and more correct.
Cc: stable@vger.kernel.org # 4.9 only
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We accidentally return success when adm8211_alloc_rings() fails but we
should preserve the error code.
Fixes: cc0b88cf5e ("[PATCH] Add adm8211 802.11b wireless driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There's no need for this to be only __read_mostly, since
it's only written in a single way depending on the module
parameter, so that can be moved into the module's __init
function, and the ops can be __ro_after_init.
This is a little bit safer since it means the ops can't
be overwritten (accidentally or otherwise), which would
otherwise cause an arbitrary function or bad pointer to
be called.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable dynamic bandwidth signalling by setting the corresponding
bit in MAC control register.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware has started making use of reserved field.
Accordingly change curr_pkt_filter from u16 to u32.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we have sdio work requests received when sdio card reset is
happening, we may end up accessing older save_adapter pointer
later which is already freed during card reset.
This patch solves the problem by cancelling those pending requests.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver does not check if mapping dma memory succeed.
The patch adds the checks and failure handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
rsi
* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d
brcmfmac
* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
bcma
* add Dell Inspiron 3148
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYQGivAAoJEG4XJFUm622bqG0IAJtSGt4Fxv2jL7GPmPpEUtYK
F6G1PCk9LxO44rOZ15E/CT1vPk6Bnwqp9brdngmXwl7jc+jGs4MQN7g6cD4UZgPm
gxjx8cah2HPRVgEE7PeOILthRxwPA+9klycsvwtglkgQ1SpQVmLHDTLpeOAkRluY
olJGINoGHTD6osud6p3oKK+VP891omJvu8TPqRjhrhLhbQTWAuTxl2Gsdye30yag
CsdaEZb9wdUEBoS80EVRwvgBzqrdKU5kGDGbuzytcyrFrRHo4flti1KgxDg3nIpI
jC4Liwg0yE/aYZlfMqi/960rt8AttCJBDt/vwqp0mOE4IwFsE9Yaio6xXUonAC8=
=a6a/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-12-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
rsi
* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d
brcmfmac
* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
bcma
* add Dell Inspiron 3148
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.10. Major changes:
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
The H2C MEDIA_STATUS_RPT command for some reason causes 8192eu and
8723bu devices not being able to reconnect.
Reported-by: Barry Day <briselec@gmail.com>
Cc: <stable@vger.kernel.org> #4.8+
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Drop duplicate header vmalloc.h from ath5k/debug.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added new areas to fw_mappings area for UCODE code
and data areas.
The new areas are only exposed through debugfs blobs,
and mainly needed to access UCODE logs.
The change does not affect crash dumps because the
newly added areas overlap with the "upper" area which
is already dumped.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
num_descriptors and descriptor_size needs to be
checked for:
1) not being negative values
2) no overflow occurs when these are multiplied
together as done in wil_pmc_read.
An overflow of two signed integers is undefined
behavior.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently it was possible to call remain_on_channel(ROC)
while scan was active and this caused a crash in the FW.
In order to fix this problem and make the behavior
consistent with other drivers, queue the ROC in case
a scan is active and try it again when scan is done.
As part of the fix, clean up some locking issues and
return error if scan is called while ROC is active.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The usb_*_msg() functions expect a timeout in msecs but are given HZ,
which is ticks per second. If HZ=100, firmware download often times out
when there is modest USB utilization and the device fails to initialize.
Replaces HZ in usb_*_msg timeouts with 1000 msec since HZ is one second
for timeouts in jiffies.
Signed-off-by: Anthony Romano <anthony.romano@coreos.com>
Acked-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Declare the structure ath_bus_ops as const as it is only passed as an
argument to the function ath9k_init_device. This argument is of type
const struct ath_bus_ops *, so ath_bus_ops structures with this property
can be declared as const.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct ath_bus_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
expression e1,e2;
@@
ath9k_init_device(e1,e2,&i@p)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct ath_bus_ops i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct ath_bus_ops i;
File size before:
text data bss dec hex filename
1295 232 0 1527 5f7 ath/ath9k/ahb.o
File size after:
text data bss dec hex filename
1359 176 0 1535 5ff ath/ath9k/ahb.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These memory chunks are often used as 'swap' by the NIC,
so it will be both reading and writing to these areas.
This seems to fix errors like this on my x86-64 machine:
kernel: DMAR: DMAR:[DMA Write] Request device [05:00.0] fault addr ff5de000
DMAR:[fault reason 05] PTE Write access is not set
Tested-by: Marek Behun <kabel@blackhole.sk>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With maximum number of vap's configured in a two radio supported
systems of ~256 Mb RAM, doing a continuous wifi down/up and
intermittent traffic streaming from the connected stations results
in failure to allocate contiguous memory for tx buffers. This results
in the disappearance of all VAP's and a manual reboot is needed as
this is not a crash (or) OOM(for OOM killer to be invoked). To address
this allocate contiguous memory for tx buffers one time and re-use them
until the modules are unloaded but this results in a slight increase in
memory footprint of ath10k when the wifi is down, but the modules are
still loaded. Also as of now we use a separate bool 'tx_mem_allocated'
to keep track of the one time memory allocation, as we cannot come up
with something like 'ath10k_tx_{register,unregister}' before
'ath10k_probe_fw' is called as 'ath10k_htt_tx_alloc_cont_frag_desc'
memory allocation is dependent on the hw_param 'continuous_frag_desc'
a) memory footprint of ath10k without the change
lsmod | grep ath10k
ath10k_core 414498 1 ath10k_pci
ath10k_pci 38236 0
b) memory footprint of ath10k with the change
ath10k_core 414980 1 ath10k_pci
ath10k_pci 38236 0
Memory Failure Call trace:
hostapd: page allocation failure: order:6, mode:0xd0
[<c021f150>] (__dma_alloc_buffer.isra.23) from
[<c021f23c>] (__alloc_remap_buffer.isra.26+0x14/0xb8)
[<c021f23c>] (__alloc_remap_buffer.isra.26) from
[<c021f664>] (__dma_alloc+0x224/0x2b8)
[<c021f664>] (__dma_alloc) from [<c021f810>]
(arm_dma_alloc+0x84/0x90)
[<c021f810>] (arm_dma_alloc) from [<bf954764>]
(ath10k_htt_tx_alloc+0xe0/0x2e4 [ath10k_core])
[<bf954764>] (ath10k_htt_tx_alloc [ath10k_core]) from
[<bf94e6ac>] (ath10k_core_start+0x538/0xcf8 [ath10k_core])
[<bf94e6ac>] (ath10k_core_start [ath10k_core]) from
[<bf947eec>] (ath10k_start+0xbc/0x56c [ath10k_core])
[<bf947eec>] (ath10k_start [ath10k_core]) from
[<bf8a7a04>] (drv_start+0x40/0x5c [mac80211])
[<bf8a7a04>] (drv_start [mac80211]) from [<bf8b7cf8>]
(ieee80211_do_open+0x170/0x82c [mac80211])
[<bf8b7cf8>] (ieee80211_do_open [mac80211]) from
[<c056afc8>] (__dev_open+0xa0/0xf4)
[21053.491752] Normal: 641*4kB (UEMR) 505*8kB (UEMR) 330*16kB (UEMR)
126*32kB (UEMR) 762*64kB (UEMR) 237*128kB (UEMR) 1*256kB (M) 0*512kB
0*1024kB 0*2048kB 0*4096kB = 95276kB
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During firmware crash (or) user requested manual restart
the system gets into a soft lock up state because of the
below root cause.
During user requested hardware restart / firmware crash
the system goes into a soft lockup state as 'napi_synchronize'
is called after 'napi_disable' (which sets 'NAPI_STATE_SCHED'
bit) and it sleeps into infinite loop as it waits for
'NAPI_STATE_SCHED' to be cleared. This condition is hit because
'ath10k_hif_stop' is called twice as below (resulting in calling
'napi_synchronize' after 'napi_disable')
'ath10k_core_restart' -> 'ath10k_hif_stop' (ATH10K_STATE_ON) ->
-> 'ieee80211_restart_hw' -> 'ath10k_start' -> 'ath10k_halt' ->
'ath10k_core_stop' -> 'ath10k_hif_stop' (ATH10K_STATE_RESTARTING)
Fix this by calling 'ath10k_halt' in ath10k_core_restart itself
as it makes more sense before informing mac80211 to restart h/w
Also remove 'ath10k_halt' in ath10k_start for the state of 'restarting'
Fixes: 3c97f5de1f ("ath10k: implement NAPI support")
Cc: <stable@vger.kernel.org> # v4.9
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is a typo bug in the current implementation of
ath10k_wmi_tlv_op_gen_pdev_set_rd.
The conformance test limits are not set up properly.
The two arguments ctl2g and ctl5g were not used at all.
Instead, the regdomain arguments rd2g and rd5g were used
for the ctl settings as well.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Radar pulse and spectral scan reports are provided by the HW
with the ATH9K_RXERR_PHY flag set. Those are forwarded to
the dfs-detector and spectral module for further processing.
For some older chips, the pre-conditions checked in those
modules are ambiguous, since ATH9K_PHYERR_RADAR is used to
tag both types. As a result, spectral frames are fed into
the dfs-detector and vice versa.
This could lead to a false radar detection on a non-DFS
channel (which is uncritical), but more relevant it causes
useless CPU load for processing invalid frames.
This commit ensures that the dfs-detector and spectral
collector are only fed when they are active.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mwifiex
* properly terminate SSIDs so that uninitalised memory is not printed
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYPZM9AAoJEG4XJFUm622bnTwH/j7KbWbTLE2H9abYJxne3sWQ
FOCrGNICgG9HYyLn33k7+dCBHGYa1f5qWO7dIeWhe6LEtXqrWBsxUFZbMrJVU7Te
sDr3s2364iIPhdLtYl5mM7M75Y2h2pt1XhpErmldCpFpnYad5vZEbIR1n96F3cz6
0ft6iUJpd3bf+KWxDUc707Vln42optvbcp7gjF+6mdShb0jlFkV9eOa85aJH6v38
5kKPhLfiv1Qs1sZXPrWc2oQUIc0LDY19sXtw/5DTLe4+r6ybsKlF1o4+b2yOVeiu
nrm1F/2D/829w3+4iYE63wACPGvyVaKYROtYgquyYkrI+6xyh1fmnout6SiwLe8=
=oEuI
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.9
mwifiex
* properly terminate SSIDs so that uninitalised memory is not printed
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a5ffbe0a19 ("rtlwifi: Fix scheduling while atomic bug") and
commit a269913c52 ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter()
to use work queue"), an error was introduced in the power-save routines
due to the fact that leaving PS was delayed by the use of a work queue.
This problem is fixed by detecting if the enter or leave routines are
in interrupt mode. If so, the workqueue is used to place the request.
If in normal mode, the enter or leave routines are called directly.
Fixes: a269913c52 ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue")
Reported-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mt7601u_mac_stop_hw should stop polling the rxq once it remains empty
but instead continues polling after the rxq status stays clear; bringing
down the interface takes about six seconds from this alone.
Speed up path by exiting rxq loop once status repeatedly polls empty.
Signed-off-by: Anthony Romano <anthony.romano@coreos.com>
Reviewed-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The scan results for scheduled scan as retrieved from the device
have changed. A field has been added which is not needed. However,
the appended info is. Luckily they are versioned so check that to
find out the location of the appended data.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
User-space can specify the interval for the scheduled scan. This
interval is found in scheduled scan plan. The driver supports only
one plan, which is legacy behaviour.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the .sched_scan_start() callback a condition was checked whether a
normal scan was ongoing. However, there is no need for this check as
it is ok to start the scheduled scan irrespective whether or not a
normal scan is ongoing.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
User-space can provide list of channels in the schedule scan request.
This was ignored so all channels supported and allowed by the device
were used. This patch configures the device to use the channels as
listed in the request.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rework .sched_scan_start() callback moving actual configuration of
the device in pno source file.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The brcmf_pno_config() function handles two configurations in
firmware. Split it and have caller sort out what is needed.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For scheduled scan we initiate an escan in firmware to obtain more
info missing from the scheduled scan notification we get from firmware.
For upcoming functionality this is also required so make it a bit
more generic.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reduce the number of parameters as the removed ones can be obtained
through struct brcmf_if parameter.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ssids list in the scheduled scan request were not properly taken
into account when configuring in firmware. The hidden bit was set for
any ssid resulting in active scanning for all. Only set it for ssids
that are in the ssids list.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introducing new source file for pno related functionality. Moving
existing pno functions.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This chip was already supported, but seems a device came up giving
a different chip identifier. So adding that effectively mapping to
the same firmware file as for 43340 chip.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rev6 of pcie host dongle interface protocol, host needs to maximum
supported ring number from dongle shared memory and set up ring buffer
and ring indices offset accordingly.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Marvell Wifi PCIe modules don't always behave nicely for PCIe power
management when their firmware hasn't been loaded, particularly after
suspending the PCIe link one or more times. When this happens, we might
end up spinning forever in this status-polling tight loop. Let's make
this less tight by adding a timeout and by sleeping a bit in between
reads, as we do with the other similar loops.
This prevents us from hogging a CPU even in such pathological cases, and
allows the FW initialization to just fail gracefully instead.
I chose the same polling parameters as the earlier loop in this
function, and empirically, I found that this loop never makes it more
than about 12 cycles in a sane FW init sequence. I had no official
information on the actual intended latency for this portion of the
download.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_usb_probe() defines and sets bcd_usb but does not use it,
Compiling with W=1 gives the following warning, fix it.
mwifiex/usb.c: In function ‘mwifiex_usb_probe’:
mwifiex/usb.c:383:41: warning: variable ‘bcd_usb’ set but not used [-Wunused-but-set-variable]
The unused variable seems to be present since 4daffe3543 which introduced
mwifiex_usb_probe().
Fixes: 4daffe3543 ("mwifiex: add support for Marvell USB8797 chipset")
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 92263a841b introduced mwifiex_deaggr_sdio_pkt which initializes
variable pkt_type but does not use it. Compiling with W=1 gives the following
warning, fix it.
mwifiex/sdio.c: In function ‘mwifiex_deaggr_sdio_pkt’:
mwifiex/sdio.c:1198:6: warning: variable ‘pkt_type’ set but not used [-Wunused-but-set-variable]
Fixes: 92263a841b ("mwifiex: add SDIO rx single port aggregation")
Cc: Zhaoyang Liu <liuzy@marvell.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_sdio_resume() intializes pm_flag, just like
mwifiex_sdio_suspend(), but does not use it. Compiling with W=1 gives
the following warning, fix it.
mwifiex/sdio.c: In function ‘mwifiex_sdio_resume’:
mwifiex/sdio.c:234:16: warning: variable ‘pm_flag’ set but not used [-Wunused-but-set-variable]
sdio_get_host_pm_caps() is just an acessor, so the call to it is safe
to remove. The unused variable seems to be present since
5e6e3a92b9 which introduced mwifiex_sdio_resume().
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 3935ccc14d introduced mwifiex_tm_cmd() which initializes
struct mwifiex_adapter* adapter, but doesn't use it.
Compiling with W=1 gives the following warning, fix it.
mwifiex/cfg80211.c: In function ‘mwifiex_tm_cmd’:
mwifiex/cfg80211.c:3973:26: warning: variable ‘adapter’ set but not used [-Wunused-but-set-variable]
Fixes: 3935ccc14d ("mwifiex: add cfg80211 testmode support")
Cc: Xinming Hu <huxm@marvell.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 429d90d221 introduced mwifiex_cmd_tdls_oper() which initializes
struct mwifiex_sta_node* sta_ptr, but does not use it. Compiling with W=1 gives
the following warning, fix it.
mwifiex/sta_cmd.c: In function ‘mwifiex_cmd_tdls_oper’:
mwifiex/sta_cmd.c:1732:27: warning: variable ‘sta_ptr’ set but not used [-Wunused-but-set-variable]
Fixes: 429d90d221 ("mwifiex: add cfg80211 tdls_oper handler support")
Cc: Avinash Patil <patila@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit b5413e6b22 removed all uses of chan_num in mwifiex_config_scan().
Compiling mwifiex with W=1 gives the following warning, fix it.
mwifiex/scan.c: In function ‘mwifiex_config_scan’:
mwifiex/scan.c:830:6: warning: variable ‘chan_num’ set but not used [-Wunused-but-set-variable]
Fixes: b5413e6b22 ("mwifiex: increase the number of nodes in command pool")
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit bec568ff51 removed the last remaining usage of struct
mwifiex_private* priv in mwifiex_fw_dpc(), by removing the call to
mwifiex_del_virtual_intf().
Compiling mwifiex/ with W=1 gives the following warning, fix it.
mwifiex/main.c: In function ‘mwifiex_fw_dpc’:
mwifiex/main.c:520:26: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
Fixes: bec568ff51 ("mwifiex: failure path handling in mwifiex_add_virtual_intf()")
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move the dev_info call that attempts to show the rate used before it is set.
Signed-off-by: Barry Day <briselec@gmail.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Barry Day <briselec@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYOAC4AAoJEG4XJFUm622bUYkH/3SSYp6moSdKpVnVPx7ST7yK
t9WHR9IMZFIhD6vq8AK6+8OQr1TgGjHfPu+WZj7CIl8nu53kcgPRi51gg1mndbNg
9N3RbVp06nGbM2VnW8ZIpg3OLIXatZ4c9g3LFvvtyobYvWGJ6W4D79JdlmTG1ELr
XAjInbxFsgon+CwqCMOaAJx8xYp42rBnPRZZvhOq9O33kRw8Umo9UQw0s1U2Vfgx
prxQ6d0GxNAPEe8QiDw/vtBcXWFMOhQeDl8sK70ZcojSn1FY730NsIh/Y86PcQTK
6TsvOL5gg+rd0ln8TZRAslnDrZBAhTEDqUzLQMRJ9VjEj5RFd8eLCSIzHfaroI8=
=4qCH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
