The remoteproc MMUs in OMAP4+ SoCs have some additional debug
registers that can give out the PC value in addition to the
MMU fault address. The PC value can be extracted properly only
on the DSP cores, and is not available on the ARM processors
within the IPU sub-systems. Instead, the MMUs have been enhanced
to throw a bus-error response back to the IPU processors.
This functionality is programmable through the MMU_GP_REG register.
The cores are simply stalled if the MMU_GP_REG.BUS_ERR_BACK_EN bit
is not set. When set, a bus-error exception is raised allowing the
processor to handle it as a bus fault and provide additional debug
information. This feature is turned on by default by the driver on
iommus supporting it.
Signed-off-by: Subramaniam Chanderashekarapuram <subramaniam.ca@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Use runtime PM functionality interfaced with hwmod enable/idle
functions, to replace direct clock operations and sysconfig
handling.
Due to reset sequence, pm_runtime_[get|put]_sync must be used, to
avoid possible operations with the module under reset. Because of
this and given that the driver uses spin_locks to protect their
critical sections, we must use pm_runtime_irq_safe in order for the
runtime ops to be happy, otherwise might_sleep_if checks in runtime
framework will complain.
The remaining pm_runtime out of iommu_enable and iommu_disable
corresponds to paths that can be accessed through debugfs, some of
them doesn't work if the module is not enabled first, but in future
if the mmu is idled withouth freeing, these are needed to debug.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Use hwmod data and device attributes to build and register an
omap device for iommu driver.
- Update the naming convention in isp module.
- Remove unneeded check for number of resources, as this is now
handled by omap_device and prevents driver from loading.
- Now unused, remove platform device and resource data, handling
of sysconfig register for softreset purposes, use default
latency structure.
- Use hwmod API for reset handling.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Move iommu/iovmm headers from plat/ to platform_data/ as part of the
single zImage work.
Partially based on an earlier version by Ido Yariv <ido@wizery.com>.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move some of the definitions in omap-iommu.h that can be made local to
either drivers/iommu.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
[tony@atomide.com: updated for header changes in the series]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This file should not be in arch/arm. Move it to drivers/iommu
to allow making most of the header local to drivers/iommu.
This is needed as we are removing plat and mach includes
from drivers for ARM common zImage support.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Cc: linux-media@vger.kernel.org
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
