This patch removes read only registers that cause invalid
address access and also updates index for measurement filter
calibration window size.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The power detector calibration is disabled because this block
doesn't exist in AR9003 based chips and also parallel
calibration is enabled otherwise the calibration will never stop.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of temperature reading samples to average
during a Tx packet is decreased to 1 from 2 to improve
5G Tx EVM with chain 0-only mode.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
sc->imask may change if ath5k_set_current_imask() races against itself.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
The reg variable is only used by __raw_writel() and __raw_readl(), which
should guarantee memory access in the right order.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implementing this callback function will cause mac80211 refrain from
going to powersave state when there are still untransmitted TX frames
in the queues.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch imports all shared header changes
from carl9170fw.git.
* update copyright boilerplate
* add some more strategic __aligned(4).
* WoWLAN
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The received tx status of aggregated frame without BlockAck may
cause deaf state in AR5416 cards. So the driver does a reset to
recover. When this happens, we release the pcu_lock before doing
a reset as ath_rest acquires pcu_lock. This is ugly and also not
atomic. Fixing this addresses the TX DMA failure also.
ath_tx_complete_aggr can be called from different paths which
takes different variants of spin_lock. This patch also addresses
the following warning.
WARNING: at kernel/timer.c:1011 del_timer_sync+0x4e/0x50()
Call Trace:
<IRQ> [<ffffffff8104be3a>] warn_slowpath_common+0x7a/0xb0
[<ffffffff8104be85>] warn_slowpath_null+0x15/0x20
[<ffffffff8105915e>] del_timer_sync+0x4e/0x50
[<ffffffffa03726be>] ath_reset+0x3e/0x210 [ath9k]
[<ffffffff8135cdaf>] ? _raw_spin_unlock_bh+0x1f/0x30
[<ffffffffa037760a>] ath_tx_complete_aggr.isra.26+0x54a/0xa40 [ath9k]
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: muddin@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The edma based (AR9003 family) chips update tx status
descriptors in a common ring buffer for all transmitted
frames. Whenever tx interrupt is raised, the descriptors
are processed and tx status index is moved.
The complete tx stauts ring are updated with beacons tx status
when there are no data frames to be sent for a period of time.
In this state, transmitting data frames causes the driver to
wait for the tx status on an incorrect tx status index though
the status was updated by hw properly. The driver detects this
condition as a h/w hang and does unnecessary chip resets.
This issue was orginally reported in adhoc mode while sending
frames after an idle time.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all that mac80211 has into the generic
ieee80211.h header file and use them. At the
same time move them from mask+shift to just
bits and rename them for consistent names.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch adds a callback to ath9k_platform_data. If the
callback is provided by the platform code, then it can be
used to hard reset the WMAC device.
The callback is required for doing a hard reset of the AR9330
chips to get them working again after a hang.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch adds the missing configuration code for diversity
group 1.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current values must be used only on AR9485 chips. Other chips
requires different values.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'ar9003_hw_antdiv_comb_conf_get' function sets div_group to 2
however that value is not used in 'ath_ant_div_comb_alt_check'.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A multiplication is missing from the current formula.
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
