Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
Split the HAVE_BPF_JIT into two for distinguishing cBPF and eBPF JITs.
Current cBPF ones:
# git grep -n HAVE_CBPF_JIT arch/
arch/arm/Kconfig:44: select HAVE_CBPF_JIT
arch/mips/Kconfig:18: select HAVE_CBPF_JIT if !CPU_MICROMIPS
arch/powerpc/Kconfig:129: select HAVE_CBPF_JIT
arch/sparc/Kconfig:35: select HAVE_CBPF_JIT
Current eBPF ones:
# git grep -n HAVE_EBPF_JIT arch/
arch/arm64/Kconfig:61: select HAVE_EBPF_JIT
arch/s390/Kconfig:126: select HAVE_EBPF_JIT if PACK_STACK && HAVE_MARCH_Z196_FEATURES
arch/x86/Kconfig:94: select HAVE_EBPF_JIT if X86_64
Later code also needs this facility to check for eBPF JITs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces:
- "select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB" as this can
now be selected directly.
- "select ARCH_WANT_OPTIONAL_GPIOLIB" with no dependency: GPIOLIB
is now selectable by everyone, so we need not declare our
intent to select it.
When ordering the symbols the following rationale was used:
if the selects were in alphabetical order, I moved select GPIOLIB
to be in alphabetical order, but if the selects were not
maintained in alphabetical order, I just replaced
"select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB".
Cc: Michael Büsch <m@bues.ch>
Cc: linux-mips@linux-mips.org
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
new device support in terms of LoC, but there has been some cleanup
in the core as well as the usual minor clk additions to various
drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a minor
refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bZFY
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The clk changes for this release cycle are mostly dominated by new
device support in terms of LoC, but there has been some cleanup in the
core as well as the usual minor clk additions to various drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a
minor refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction
dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (197 commits)
clk: bcm2835: fix check of error code returned by devm_ioremap_resource()
clk: renesas: div6: use RENESAS for #define
clk: renesas: Rename header file renesas.h
clk: max77{686,802}: Remove CLK_IS_ROOT
clk: versatile: Remove CLK_IS_ROOT
clk: sunxi: Remove use of variable length array
clk: fixed-rate: Remove CLK_IS_ROOT
clk: qcom: Remove CLK_IS_ROOT
doc: dt: add documentation for lpc1850-creg-clk driver
clk: add lpc18xx creg clk driver
clk: lpc32xx: fix compilation warning
clk: xgene: Add missing parenthesis when clearing divider value
clk: mb86s7x: Remove CLK_IS_ROOT
clk: x86: Remove clkdev.h and clk.h includes
clk: x86: Remove CLK_IS_ROOT
clk: mvebu: Remove CLK_IS_ROOT
clk: renesas: move drivers to renesas directory
clk: si5{14,351,70}: Remove CLK_IS_ROOT
clk: scpi: Remove CLK_IS_ROOT
clk: s2mps11: Remove CLK_IS_ROOT
...
Include pci/hotplug/Kconfig directly from pci/Kconfig, so arches don't
have to source both pci/Kconfig and pci/hotplug/Kconfig.
Note that this effectively adds pci/hotplug/Kconfig to the following
arches, because they already sourced drivers/pci/Kconfig but they
previously did not source drivers/pci/hotplug/Kconfig:
alpha
arm
avr32
frv
m68k
microblaze
mn10300
sparc
unicore32
Inspired-by-patch-from: Bogicevic Sasa <brutallesale@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Include pci/pcie/Kconfig directly from pci/Kconfig, so arches don't
have to source both pci/Kconfig and pci/pcie/Kconfig.
Note that this effectively adds pci/pcie/Kconfig to the following
arches, because they already sourced drivers/pci/Kconfig but they
previously did not source drivers/pci/pcie/Kconfig:
alpha
avr32
blackfin
frv
m32r
m68k
microblaze
mn10300
parisc
sparc
unicore32
xtensa
[bhelgaas: changelog, source pci/pcie/Kconfig at top of pci/Kconfig, whitespace]
Signed-off-by: Sasa Bogicevic <brutallesale@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This config was used for the ARM port so that it could use a
machine specific clkdev.h include, but those are all gone now.
The MIPS architecture is the last user, and from what I can tell
it doesn't actually use it anyway, so let's remove the config all
together.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Joshua Henderson <joshua.henderson@microchip.com>
We now have a generic IPI layer that will use GIC automatically
if it's compiled in.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-19-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add the BCM6345 interrupt controller based on the SMP-capable BCM7038
and the BCM3380 but with packed interrupt registers.
Add the BCM6345 interrupt controller to a list with the existing BCM7038
so that interrupts on CPU1 are not ignored.
Update the maintainers file list for BMIPS to include this driver.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: linux-mips@linux-mips.org
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Rob Herring <robh@kernel.org>
Link: http://lkml.kernel.org/r/5651D176.6030908@simon.arlott.org.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.
The executive summary:
- ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
- Avoid useless rebuilds for zboot.
- jz4780: Add NEMC, BCH and NAND device tree nodes
- Initial support for the MicroChip's DT platform. As all the device
drivers are missing this is still of limited use.
- Some Loongson3 cleanups.
- The unavoidable whitespace polishing.
- Reduce clock skew when synchronizing the CPU cycle counters on CPU
startup.
- Add MIPS R6 fixes.
- Lots of cleanups across arch/mips as fallout from KVM.
- Lots of minor fixes and changes for IEEE 754-2008 support to the
FPU emulator / fp-assist software.
- Minor Ralink, BCM47xx and bcm963xx platform support improvments.
- Support SMP on BCM63168"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
MIPS: zboot: Add support for serial debug using the PROM
MIPS: zboot: Avoid useless rebuilds
MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
MIPS: bcm963xx: Update bcm_tag field image_sequence
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
MIPS: bcm63xx: nvram: Use nvram structure definition from header file
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
MAINTAINERS: Add KVM for MIPS entry
MIPS: KVM: Add missing newline to kvm_err()
MIPS: Move KVM specific opcodes into asm/inst.h
MIPS: KVM: Use cacheops.h definitions
MIPS: Break down cacheops.h definitions
MIPS: Use EXCCODE_ constants with set_except_vector()
MIPS: Update trap codes
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
MIPS: KVM: Make kvm_mips_{init,exit}() static
MIPS: KVM: Refactor added offsetof()s
MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
...
As most platforms implement the PROM serial interface prom_putchar()
add a simple bridge to allow re-using this code for zboot.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11811/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds support for the Microchip PIC32 MIPS microcontroller with the
specific variant PIC32MZDA. PIC32MZDA is based on the MIPS m14KEc core
and boots using device tree.
This includes an early pin setup and early clock setup needed prior to
device tree being initialized. In additon, an interface is provided to
synchronize access to registers shared across several peripherals.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12097/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the generic implementation to <linux/dma-mapping.h> now that all
architectures support it and remove the HAVE_DMA_ATTR Kconfig symbol now
that everyone supports them.
[valentinrothberg@gmail.com: remove leftovers in Kconfig]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For bootloaders that support booting only ELF kernels and load only ELF
segments to memory there is no easy way to supply DTB without kernel
recompilation. For that purpose, create a section called .appended_dtb
that can be later updated with board-specific DTB using binutils e.g. at
kernel installation time.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11114/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Seval of-enabled machines (bmips, lantiq, xlp, pistachio, ralink) copied
the arguments from dtb to arcs_command_line to prevent the kernel from
overwriting them.
Since there is now an option to keep the dtb arguments, default to the
new option remove the "backup" to arcs_command_line in case of USE_OF is
enabled, except for those platforms that still take the bootloader
arguments or do not use any at all.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Ganesan Ramalingam <ganesanr@broadcom.com>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11285/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Similar to how arm allows using selecting between bootloader arguments,
dtb arguments and both, allow to select them on mips. But since we have
less control over the place of the dtb do not modify it but instead use
the boot_command_line for merging them.
The default is "use bootloader arguments" to keep the current behaviour
as default.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Ganesan Ramalingam <ganesanr@broadcom.com>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11284/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since OF is now a user selectable symbol, the choice for appended dtb
support should only be visible when USE_OF is selected, as this
indicates actual machine support for device tree in MIPS.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Ganesan Ramalingam <ganesanr@broadcom.com>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11283/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add user-mode implementations of gettimeofday() and clock_gettime() to
the VDSO. This is currently usable with 2 clocksources: the CP0 count
register, which is accessible to user-mode via RDHWR on R2 and later
cores, or the MIPS Global Interrupt Controller (GIC) timer, which
provides a "user-mode visible" section containing a mirror of its
counter registers. This section must be mapped into user memory, which
is done below the VDSO data page.
When a supported clocksource is not in use, the VDSO functions will
return -ENOSYS, which causes libc to fall back on the standard syscall
path.
When support for neither of these clocksources is compiled into the
kernel at all, the VDSO still provides clock_gettime(), as the coarse
realtime/monotonic clocks can still be implemented. However,
gettimeofday() is not provided in this case as nothing can be done
without a suitable clocksource. This causes the symbol lookup to fail
in libc and it will then always use the standard syscall path.
This patch includes a workaround for a bug in QEMU which results in
RDHWR on the CP0 count register always returning a constant (incorrect)
value. A fix for this has been submitted, and the workaround can be
removed after the fix has been in stable releases for a reasonable
amount of time.
A simple performance test which calls gettimeofday() 1000 times in a
loop and calculates the average execution time gives the following
results on a Malta + I6400 (running at 20MHz):
- Syscall: ~31000 ns
- VDSO (GIC): ~15000 ns
- VDSO (CP0): ~9500 ns
[markos.chandras@imgtec.com:
- Minor code re-arrangements in order for mappings to be made
in the order they appear to the process' address space.
- Move do_{monotonic, realtime} outside of the MIPS_CLOCK_VSYSCALL ifdef
- Use gic_get_usm_range so we can do the GIC mapping in the
arch/mips/kernel/vdso instead of the GIC irqchip driver]
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If we fail to register any real SMP implementations, fall back to
registering the dummy UP implementation. Otherwise when we build an SMP
kernel & run it on a system where the SMP implementations fail to probe
(eg. QEMU) the kernel will perform a NULL dereference attempting to call
mp_ops->smp_setup() from plat_smp_setup().
Notably this fixes booting kernels with CPS SMP enabled on QEMU, which
doesn't currently implement the CM, CPC or GIC.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11223/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move memory configuration to be performed via device tree for the Malta
board. This moves more Malta specific code to malta-dtshim.c, leaving
the rest of the mti-malta code a little more board-agnostic. This will
be useful to share more code between boards, with the device tree
providing the board specifics as intended.
Since we can't rely upon Malta boards running a bootloader capable of
handling devictrees & filling in the required information, a piece of
shim code (malta_dt_shim) is added to consume the (e)memsize variables
provided as part of the bootloader environment (or on the kernel command
line) then generate the DT memory node using the provided values.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Kumar Gala <galak@codeaurora.org>
Cc: linux-kernel@vger.kernel.org
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Patchwork: https://patchwork.linux-mips.org/patch/11222/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A boundary exists beyond which the timer frequency becomes high enough
that timer interrupts saturate the system and either cause it to slow to
a crawl or stop functioning entirely. Where that boundary lies depends
upon a number of factors such as the overhead of each interrupt and the
overall speed of the CPU, but correlates strongly with the clock
frequency at which the CPU runs. When running on emulators during
bringup or debug of a CPU that clock frequency is very low, which
results in the boundary at which the timer frequency becomes
unsustainable being very low. The current minimum of 48Hz pushes against
boundary in certain situations in current systems. Allow the kernel to
be configured for a 24Hz timer frequency in order to avoid problems on
such slow running systems.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11184/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
ARCH_USE_BUILTIN_BSWAP will use __builtin_bswap16(), __builtin_bswap32()
and __builtin_bswap64() where available. This allows better instruction
scheduling. On pre-R2 processors it will result in 32 bit and 64 bit
swapping being performed in a call to a __bswapsi2() rsp. __bswapdi2()
functions, so we add these, too.
For a 4.2 kernel with GCC 4.9 this yields the following kernel sizes:
text data bss dec hex filename
3996071 155804 88992 4240867 40b5e3 vmlinux ip22 baseline
3985687 159900 88992 4234579 409d53 vmlinux ip22 + bswap patch
6913157 378552 251024 7542733 7317cd vmlinux ip27 baseline
6878581 378552 251024 7508157 7290bd vmlinux ip27 + bswap patch
5773777 268752 187424 6229953 5f0fc1 vmlinux malta baseline
5773401 268752 187424 6229577 5f0e49 vmlinux malta + bswap patch
Presumably the code size improvments yield better cache hit rate thus
better performance compensating for the extra function call but this
will still need to be benchmarked.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are two kexec load syscalls, kexec_load another and kexec_file_load.
kexec_file_load has been splited as kernel/kexec_file.c. In this patch I
split kexec_load syscall code to kernel/kexec.c.
And add a new kconfig option KEXEC_CORE, so we can disable kexec_load and
use kexec_file_load only, or vice verse.
The original requirement is from Ted Ts'o, he want kexec kernel signature
being checked with CONFIG_KEXEC_VERIFY_SIG enabled. But kexec-tools use
kexec_load syscall can bypass the checking.
Vivek Goyal proposed to create a common kconfig option so user can compile
in only one syscall for loading kexec kernel. KEXEC/KEXEC_FILE selects
KEXEC_CORE so that old config files still work.
Because there's general code need CONFIG_KEXEC_CORE, so I updated all the
architecture Kconfig with a new option KEXEC_CORE, and let KEXEC selects
KEXEC_CORE in arch Kconfig. Also updated general kernel code with to
kexec_load syscall.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Young <dyoung@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
This commit introduces a new config, so the user can choose to enable
the General Purpose Timer based clocksource. This option is required
to have CPUFreq support.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <James.Hartley@imgtec.com>
Cc: Govindraj Raja <Govindraj.Raja@imgtec.com>
Cc: Damien Horsley <Damien.Horsley@imgtec.com>
Cc: James Hogan <James.Hogan@imgtec.com>
Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/10887/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that we're ready to enable COMMON_CLK for GIC platforms do so for
Malta and SEAD3. The only other user of the GIC Pistachio does already
do so.
[ralf@linux-mips.org: Rewrite the commit message because applied in the
right order there is no breakage thus no fix required.]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11038/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is needed to enable GPIO framework support for Netlogic XLP platform.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10818/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently CONFIG_ARCH_HAVE_CUSTOM_GPIO_H is defined for all MIPS
machines, and each machine type provides its own gpio.h. However
only a handful really implement the GPIO API, most just forward
everythings to gpiolib.
The Alchemy machine is notable as it provides a system to allow
implementing the GPIO API at the board level. But it is not used by
any board currently supported, so it can also be removed.
For most machine types we can just remove the custom gpio.h, as well
as the custom wrappers if some exists. Some of the code found in
the wrappers must be moved to the respective GPIO driver.
A few more fixes are need in some drivers as they rely on linux/gpio.h
to provides some machine specific definitions, or used asm/gpio.h
instead of linux/gpio.h for the gpio API.
Signed-off-by: Alban Bedel <albeu@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Daniel Walter <dwalter@google.com>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Buesch <m@bues.ch>
Cc: abdoulaye berthe <berthe.ab@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10828/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On MIPS64 we have spinlocks that are 32b in size and an efficient
cmpxchg64 implementation, so we qualify to make use of cmpxchg backed
lockrefs. Select the ARCH_USE_CMPXCHG_LOCKREF Kconfig symbol and provide
a trivial implementation of arch_spin_value_unlocked to satisfy the
lockref code.
Using Linus' simple testcase from
http://article.gmane.org/gmane.linux.file-systems/77466 on a dual core
system with an in-development MIPS64 CPU running on FPGA I see around an
8% gain:
Pre-patch:
Total loops: 252698
Total loops: 251482
Total loops: 250806
Total loops: 252885
Total loops: 251666
Post-patch:
Total loops: 273728
Total loops: 269932
Total loops: 269341
Total loops: 275004
Total loops: 270208
[ralf@linux-mips.org: Fixed conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: Maciej W. Rozycki <macro@codesourcery.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/10810/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CONFIG_MIPS_O32_FP64_SUPPORT and CONFIG_CPU_HAS_MSA are in pretty good
shape these days, and in much wider use than they once were. Stop
referring to them as EXPERIMENTAL.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10801/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS R6 ISA support has been part of mainline since v4.0
and it should be in a good shape nowadays so it is not an
experimental feature anymore.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10731/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
Some releases this branch is nearly empty, others we have more stuff. It
tends to gather drivers that need SoC modification or dependencies such
that they have to (also) go in through our tree.
For this release, we have merged in part of the reset controller tree
(with handshake that the parts we have merged in will remain stable),
as well as dependencies on a few clock branches.
In general, new items here are:
- Qualcomm driver for SMM/SMD, which is how they communicate with the
coprocessors on (some) of their platforms
- Memory controller work for ARM's PL172 memory controller
- Reset drivers for various platforms
- PMU power domain support for Marvell platforms
- Tegra support for T132/T210 SoCs: PMC, fuse, memory controller per-SoC support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=B6jn
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Some releases this branch is nearly empty, others we have more stuff.
It tends to gather drivers that need SoC modification or dependencies
such that they have to (also) go in through our tree.
For this release, we have merged in part of the reset controller tree
(with handshake that the parts we have merged in will remain stable),
as well as dependencies on a few clock branches.
In general, new items here are:
- Qualcomm driver for SMM/SMD, which is how they communicate with the
coprocessors on (some) of their platforms
- memory controller work for ARM's PL172 memory controller
- reset drivers for various platforms
- PMU power domain support for Marvell platforms
- Tegra support for T132/T210 SoCs: PMC, fuse, memory controller
per-SoC support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
ARM: tegra: cpuidle: implement cpuidle_state.enter_freeze()
ARM: tegra: Disable cpuidle if PSCI is available
soc/tegra: pmc: Use existing pclk reference
soc/tegra: pmc: Remove unnecessary return statement
soc: tegra: Remove redundant $(CONFIG_ARCH_TEGRA) in Makefile
memory: tegra: Add Tegra210 support
memory: tegra: Add support for a variable-size client ID bitfield
clk: shmobile: rz: Add CPG/MSTP Clock Domain support
clk: shmobile: rcar-gen2: Add CPG/MSTP Clock Domain support
clk: shmobile: r8a7779: Add CPG/MSTP Clock Domain support
clk: shmobile: r8a7778: Add CPG/MSTP Clock Domain support
clk: shmobile: Add CPG/MSTP Clock Domain support
ARM: dove: create a proper PMU driver for power domains, PMU IRQs and resets
reset: reset-zynq: Adding support for Xilinx Zynq reset controller.
docs: dts: Added documentation for Xilinx Zynq Reset Controller bindings.
MIPS: ath79: Add the reset controller to the AR9132 dtsi
reset: Add a driver for the reset controller on the AR71XX/AR9XXX
devicetree: Add bindings for the ATH79 reset controller
reset: socfpga: Update reset-socfpga to read the altr,modrst-offset property
doc: dt: add documentation for lpc1850-rgu reset driver
...
R6 does not support the MIPS MT ASE and the CMP/SMP options so
restrict them in order to prevent users from selecting incompatible
SMP configuration for R6 cores. We also disable the CPS/SMP option
because its support hasn't been added to the CPS code yet.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10637/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The AR71XX/AR9XXX SoC have a simple reset controller with one bit per
reset line.
Signed-off-by: Alban Bedel <albeu@free.fr>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This was left over from an earlier iteration of the BMIPS irqchip changes.
It doesn't actually have an effect, so let's nuke it.
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: stable@vger.kernel.org # v4.1+
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9910/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pass 1 parts had a number of significant erratas and were only available
in small numbers and under NDA. Full support also required the use of a
special toolchain that kept branches properly aligned. These workarounds
were never upstreamed and the only toolchain known to have them is
Montavista's GCC 3.0-based toolchain which completly obsoleted if not
useless these days.
So now that automated testing has tripped over the user of the
-msb1-pass1-workarounds option, rather than fixing it remove support for
pass 1 parts.
Probably nobody will notice. I seem to own the last know pass 1 board
and I haven't noticed another one in the wild in the past decade, at
least.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS32r6 code requires FP64 (ie. FR=1) support. Building a kernel with
support for MIPS32r6 binaries but without support for O32 with FP64 is
therefore a problem which can lead to incorrectly executed userland.
CONFIG_MIPS_O32_FP64_SUPPORT is already selected when the kernel is
configured for MIPS32r6, but not when the kernel is configured for
MIPS64r6 with O32 compat support. Select CONFIG_MIPS_O32_FP64_SUPPORT in
such configurations to prevent building kernels which execute MIPS32r6
userland incorrectly.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v4.0-
Cc: linux-mips@linux-mips.org
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: stable@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10674/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
