Add urt0 txd and rxd muxing setup in the dtsi because uart0 always uses
them to work, no other possibilities.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Add an ethernet0 alias for the RK3368 mac interface so
that u-boot can find the device-node and fill in the mac address on
boards that support a wired network interface.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch add syscon-reboot node to reboot exynos7 based SoCs.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch enables HS200 mode operation on Exynos7 based
Espresso board.
This also removes _broken-cd_ property as per mmc binding documentation
which says one of the properties between broken-cd and non-removable
should be used. And we already use _non-removable_ as emmc is mounted
on the board which is a non-removable device.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds PMIC (S2MPS15) node on Espresso board,
which includes regulators and pmic-clk sub-nodes.
This patch also adds {vmmc,vqmmc}-supply properties for mmc2 node.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
In APM X-Gene SoC (both v1 and v2), each pair of processors
shares the same L2 cache. This patch adds l2-cache entries into
X-Gene SoC device tree to demonstrate this configuration.
Signed-off-by: Duc Dang <dhdang@apm.com>
This patch adds DTS entries for Designware I2C controllers used in
APM X-Gene v2 evaluation platform (Merlin board).
X-Gene v2 has total 5 I2C controllers. On Merlin board only I2C1
and I2C4 controllers are available in Linux, where the other 3
controllers are used for management purpose (power management,
BMC function).
Signed-off-by: Duc Dang <dhdang@apm.com>
This patch adds DTS entries for Designware I2C controller used in
APM X-Gene v1 SoC evaluation platform (Mustang board).
APM X-Gene v1 SoC has 2 I2C controllers. On Mustang board,
I2C1 is used to implement proxy I2C interface; I2C1 can be
used as I2C slave port (for BMC) or as I2C master port (if
no BMC is used). Only I2C1 DT entry is added in this
patch with default status as 'disabled'.
Signed-off-by: Duc Dang <dhdang@apm.com>
This patch adds device tree nodes to enable driver for True Random
Number Generator (TRNG) on APM X-Gene v2 platforms.
Signed-off-by: Duc Dang <dhdang@apm.com>
Remove register information used to reset and enable/disable clock
for AHB block as reseting AHB or disabling its clock will make other
peripherals attached to it stop working.
Signed-off-by: Duc Dang <dhdang@apm.com>
The NAND controller on NS2 SoC is compatible with existing
BRCM IPROC NAND driver so let's enable it in NS2 DT and
NS2 SVK DT.
This patch also fixes use of node labels in ns2-svk.dts.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch adds iProc I2C DT nodes for NS2 and enable them for the NS2
SVK board
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We have IPROC RNG200 hardware random number generation in
NS2 SoC, lets enable it for NS2 in NS2 DT.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Pramod KUMAR <pramodku@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The NS2 SoC has Cortex-A57 CPUs which support ARM PMUv3 so,
lets enable ARM PMUv3 in NS2 DT.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
To reset NS2, we simply have to write '0' to BIT[1] at offset 0x90
of CRMU space.
The above can be easily achieved by writing 0xfffffffd at offset 0x90
using syscon-reboot driver. We don't need to have separate driver for
rebooting NS2.
This patch enables syscon-reboot driver for NS2 using DT.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The SMMU-500 driver is already available in Linux kernel. Let's
enable it for NS2 in DT.
This patch keeps mmu-masters attribute empty so that driver patches
can later extend this attribute when adding device DT nodes.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add initial board support for r8a7795 Salvator-X. At this point
only DEBUG0 and DEBUG1 serial ports are supported.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add dummy nodes for the 3 DMA controllers.
This allows to start describing DMA channels for DMA slaves now.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As usual, this is the massive branch we have for each release. Lots of
various updates and additions of hardware descriptions on existing hardware,
as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and 32-bit
DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to tell
from the diffstat, so there's little point in duplicating listing it here.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWQT2WAAoJEIwa5zzehBx37tgQAIBe5eDJFXFihTlyOQ2plL3q
vVH4OCzXIHELfM1J8CGZNah1wCQqNOts8RAmDCzxr+zSYuLOwJOEDZ6NKmErMxl0
NTj3+BsqKO3NRym970ofPqU9JRLQmpZ8K7dzk8Nwj2+r1WZHFu/j6Jv44n/Ns0lw
7+wxnG322lTm7SnvALCMD5lD4Y7VpThooWy5SdFtRoAetn+cLbVCJIeeQvO6Vxkp
NooeJR0t2e8cpbAND5Jwu6eeWRcIbrvgjYDe0omhrIY05i9yNvIsC2HuQFGjF43z
p2CnQvcKnhOXTZw3yse1Fx5igA7jqwVjjC/lVeDyxhusAtLpmuB6qbSaj7DpqkSQ
nJxX1d49WKm68K+aknmee1kYRrvc4DE/kORI4IxXnsVNMu16ifTVLnxKgUhwzukb
eZdTP6rsqgNozaYvh0k1vfSFd+CNSkBg+E9nrI3tU95yo3LOIhobVBCvBcWlmUvQ
JdavRztqosChjIx3a9i1eCNKJtCg9p4m+gWjUqVVWsxBHe/3HojzjZnsBSynIQMA
uGIVm0TKhNl1Svxl3oJo9257UCUK7+5PqJHK9IHrcWDULYx05JGSjuZcyvNS6Fo+
u1DMf0ud4gXJYhecFBa7b3zRjk5YxptgCCTjeEEOTUJbbhZqDjGFZlNuFi6dmqD3
ILJ2QMe/DGiPIlUmCfsx
=qY1q
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, this is the massive branch we have for each release. Lots
of various updates and additions of hardware descriptions on existing
hardware, as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and
32-bit DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to
tell from the diffstat, so there's little point in duplicating listing
it here)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
ARM: dts: uniphier: add system-bus-controller nodes
ARM64: juno: disable NOR flash node by default
ARM: dts: uniphier: add outer cache controller nodes
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
dts/ls2080a: Update Simulator DTS to add support of various peripherals
dts/ls2080a: Remove text about writing to Free Software Foundation
dts/ls2080a: Update DTSI to add support of various peripherals
doc: DTS: Update DWC3 binding to provide reference to generic bindings
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
arm64: Rename FSL LS2085A SoC support code to LS2080A
arm64: Use generic Layerscape SoC family naming
ARM: dts: uniphier: add ProXstream2 Vodka board support
ARM: dts: uniphier: add ProXstream2 Gentil board support
...
Merging in the few patches I had kept separate from main next/dt, since others
got merged here directly.
* next/arm64:
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
arm64: dts: mt8173: Add clocks for SCPSYS unit
arm64: dts: mt8173: Add subsystem clock controller device nodes
+ Linux 4.3-rc5
- DT binding doc consolidation moving similar bindings to common
locations. The majority of these are display related which were
scattered in video/, fb/, drm/, gpu/, and panel/ directories.
- Add new config option, CONFIG_OF_ALL_DTBS, to enable building all dtbs
in the tree for most arches with dts files (except powerpc for now).
- OF_IRQ=n fixes for user enabled CONFIG_OF.
- of_node_put ref counting fixes from Julia Lawall.
- Common DT binding for wakeup-source and deprecation of all similar
bindings.
- DT binding for PXA LCD controller.
- Allow ignoring failed PCI resource translations in order to ignore
64-bit addresses on non-LPAE 32-bit kernels.
- Support setting the NUMA node from DT instead of only from parent
device.
- Couple of earlycon DT parsing fixes for address and options.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWO+HwAAoJEPr7XbWNvGHDFOoP/RcK4z5dtVQL2XRFbJBqRBZU
riMc4BZkwpcKGXjzZlMrLw+mg4vaoLKSIAGAsYkgdDOKbYphQQdVwDzN099Fzpzy
EE6K7Q+AW618z34AWdDjcpJYzSFnjAjYdh6JabohmKdPlxobR1RsKT+nRpDOGfeO
c1DmxAQ1Fiav+xAI4m0YUuyxQDUeFYC0mVcVPzRbWZj31Ia5BgIrvT+V7fM55CTb
dOAYWDHrfOw+yYI98sqZoSAb5H+E3UuY1ymBMhiP16Ot2vCyIKRYwhDokF9VYO/0
MpIMhCgv1jmE5NCbBeYSSJUePySvvnuyYe6HIaJQjV8KGEZ5C7c1iLMgtvov2KVI
bcSx6nPH/u5FuWIhWdMINPc50AQBAK/akYcgoCVjioVX+4WY2pqLvsXW2arEr//Z
XY3FUpgS6eI42HBsj4SxrGnzaRc2jPOs6yiANkywmHnpWcyvszCxUEvf0Mh0cbkm
diu31/owdpUO5imCe+ErtGVV3vY2VUMnbcm8J61pqL52OZNPLZUUEfktv1JCGW7y
cVdnlgeGSFuCbY4jUErvxtQGJQLFwf7Gg1U/VfFXX2iuQGAACB1KwxY5sR6P5Ghz
W6NvOTT36kaM9WGqn/bquOd6EmKcx9aZfgRLOkgV86Q/11gHKpuRjkrsth7rIJDI
97qkGiWl4t1Ll5T4StK8
=tGCy
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A fairly large (by DT standards) pull request this time with the
majority being some overdue moving DT binding docs around to
consolidate similar bindings.
- DT binding doc consolidation moving similar bindings to common
locations. The majority of these are display related which were
scattered in video/, fb/, drm/, gpu/, and panel/ directories.
- Add new config option, CONFIG_OF_ALL_DTBS, to enable building all
dtbs in the tree for most arches with dts files (except powerpc for
now).
- OF_IRQ=n fixes for user enabled CONFIG_OF.
- of_node_put ref counting fixes from Julia Lawall.
- Common DT binding for wakeup-source and deprecation of all similar
bindings.
- DT binding for PXA LCD controller.
- Allow ignoring failed PCI resource translations in order to ignore
64-bit addresses on non-LPAE 32-bit kernels.
- Support setting the NUMA node from DT instead of only from parent
device.
- Couple of earlycon DT parsing fixes for address and options"
* tag 'devicetree-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (45 commits)
MAINTAINERS: update DT binding doc locations
devicetree: add Sigma Designs vendor prefix
of: simplify arch_find_n_match_cpu_physical_id() function
Documentation: arm: Fixed typo in socfpga fpga mgr example
Documentation: devicetree: fix reference to legacy wakeup properties
Documentation: devicetree: standardize/consolidate on "wakeup-source" property
drivers: of: removing assignment of 0 to static variable
xtensa: enable building of all dtbs
mips: enable building of all dtbs
metag: enable building of all dtbs
metag: use common make variables for dtb builds
h8300: enable building of all dtbs
arm64: enable building of all dtbs
arm: enable building of all dtbs
arc: enable building of all dtbs
arc: use common make variables for dtb builds
of: add config option to enable building of all dtbs
of/fdt: fix error checking for earlycon address
of/overlay: add missing of_node_put
of/platform: add missing of_node_put
...
- "genirq: Introduce generic irq migration for cpu hotunplugged" patch
merged from tip/irq/for-arm to allow the arm64-specific part to be
upstreamed via the arm64 tree
- CPU feature detection reworked to cope with heterogeneous systems
where CPUs may not have exactly the same features. The features
reported by the kernel via internal data structures or ELF_HWCAP are
delayed until all the CPUs are up (and before user space starts)
- Support for 16KB pages, with the additional bonus of a 36-bit VA
space, though the latter only depending on EXPERT
- Implement native {relaxed, acquire, release} atomics for arm64
- New ASID allocation algorithm which avoids IPI on roll-over, together
with TLB invalidation optimisations (using local vs global where
feasible)
- KASan support for arm64
- EFI_STUB clean-up and isolation for the kernel proper (required by
KASan)
- copy_{to,from,in}_user optimisations (sharing the memcpy template)
- perf: moving arm64 to the arm32/64 shared PMU framework
- L1_CACHE_BYTES increased to 128 to accommodate Cavium hardware
- Support for the contiguous PTE hint on kernel mapping (16 consecutive
entries may be able to use a single TLB entry)
- Generic CONFIG_HZ now used on arm64
- defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3six
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- "genirq: Introduce generic irq migration for cpu hotunplugged" patch
merged from tip/irq/for-arm to allow the arm64-specific part to be
upstreamed via the arm64 tree
- CPU feature detection reworked to cope with heterogeneous systems
where CPUs may not have exactly the same features. The features
reported by the kernel via internal data structures or ELF_HWCAP are
delayed until all the CPUs are up (and before user space starts)
- Support for 16KB pages, with the additional bonus of a 36-bit VA
space, though the latter only depending on EXPERT
- Implement native {relaxed, acquire, release} atomics for arm64
- New ASID allocation algorithm which avoids IPI on roll-over, together
with TLB invalidation optimisations (using local vs global where
feasible)
- KASan support for arm64
- EFI_STUB clean-up and isolation for the kernel proper (required by
KASan)
- copy_{to,from,in}_user optimisations (sharing the memcpy template)
- perf: moving arm64 to the arm32/64 shared PMU framework
- L1_CACHE_BYTES increased to 128 to accommodate Cavium hardware
- Support for the contiguous PTE hint on kernel mapping (16 consecutive
entries may be able to use a single TLB entry)
- Generic CONFIG_HZ now used on arm64
- defconfig updates
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (91 commits)
arm64/efi: fix libstub build under CONFIG_MODVERSIONS
ARM64: Enable multi-core scheduler support by default
arm64/efi: move arm64 specific stub C code to libstub
arm64: page-align sections for DEBUG_RODATA
arm64: Fix build with CONFIG_ZONE_DMA=n
arm64: Fix compat register mappings
arm64: Increase the max granular size
arm64: remove bogus TASK_SIZE_64 check
arm64: make Timer Interrupt Frequency selectable
arm64/mm: use PAGE_ALIGNED instead of IS_ALIGNED
arm64: cachetype: fix definitions of ICACHEF_* flags
arm64: cpufeature: declare enable_cpu_capabilities as static
genirq: Make the cpuhotplug migration code less noisy
arm64: Constify hwcap name string arrays
arm64/kvm: Make use of the system wide safe values
arm64/debug: Make use of the system wide safe value
arm64: Move FP/ASIMD hwcap handling to common code
arm64/HWCAP: Use system wide safe values
arm64/capabilities: Make use of system wide safe value
arm64: Delay cpu feature capability checks
...
Pull networking updates from David Miller:
Changes of note:
1) Allow to schedule ICMP packets in IPVS, from Alex Gartrell.
2) Provide FIB table ID in ipv4 route dumps just as ipv6 does, from
David Ahern.
3) Allow the user to ask for the statistics to be filtered out of
ipv4/ipv6 address netlink dumps. From Sowmini Varadhan.
4) More work to pass the network namespace context around deep into
various packet path APIs, starting with the netfilter hooks. From
Eric W Biederman.
5) Add layer 2 TX/RX checksum offloading to qeth driver, from Thomas
Richter.
6) Use usec resolution for SYN/ACK RTTs in TCP, from Yuchung Cheng.
7) Support Very High Throughput in wireless MESH code, from Bob
Copeland.
8) Allow setting the ageing_time in switchdev/rocker. From Scott
Feldman.
9) Properly autoload L2TP type modules, from Stephen Hemminger.
10) Fix and enable offload features by default in 8139cp driver, from
David Woodhouse.
11) Support both ipv4 and ipv6 sockets in a single vxlan device, from
Jiri Benc.
12) Fix CWND limiting of thin streams in TCP, from Bendik Rønning
Opstad.
13) Fix IPSEC flowcache overflows on large systems, from Steffen
Klassert.
14) Convert bridging to track VLANs using rhashtable entries rather than
a bitmap. From Nikolay Aleksandrov.
15) Make TCP listener handling completely lockless, this is a major
accomplishment. Incoming request sockets now live in the
established hash table just like any other socket too.
From Eric Dumazet.
15) Provide more bridging attributes to netlink, from Nikolay
Aleksandrov.
16) Use hash based algorithm for ipv4 multipath routing, this was very
long overdue. From Peter Nørlund.
17) Several y2038 cures, mostly avoiding timespec. From Arnd Bergmann.
18) Allow non-root execution of EBPF programs, from Alexei Starovoitov.
19) Support SO_INCOMING_CPU as setsockopt, from Eric Dumazet. This
influences the port binding selection logic used by SO_REUSEPORT.
20) Add ipv6 support to VRF, from David Ahern.
21) Add support for Mellanox Spectrum switch ASIC, from Jiri Pirko.
22) Add rtl8xxxu Realtek wireless driver, from Jes Sorensen.
23) Implement RACK loss recovery in TCP, from Yuchung Cheng.
24) Support multipath routes in MPLS, from Roopa Prabhu.
25) Fix POLLOUT notification for listening sockets in AF_UNIX, from Eric
Dumazet.
26) Add new QED Qlogic river, from Yuval Mintz, Manish Chopra, and
Sudarsana Kalluru.
27) Don't fetch timestamps on AF_UNIX sockets, from Hannes Frederic
Sowa.
28) Support ipv6 geneve tunnels, from John W Linville.
29) Add flood control support to switchdev layer, from Ido Schimmel.
30) Fix CHECKSUM_PARTIAL handling of potentially fragmented frames, from
Hannes Frederic Sowa.
31) Support persistent maps and progs in bpf, from Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1790 commits)
sh_eth: use DMA barriers
switchdev: respect SKIP_EOPNOTSUPP flag in case there is no recursion
net: sched: kill dead code in sch_choke.c
irda: Delete an unnecessary check before the function call "irlmp_unregister_service"
net: dsa: mv88e6xxx: include DSA ports in VLANs
net: dsa: mv88e6xxx: disable SA learning for DSA and CPU ports
net/core: fix for_each_netdev_feature
vlan: Invoke driver vlan hooks only if device is present
arcnet/com20020: add LEDS_CLASS dependency
bpf, verifier: annotate verbose printer with __printf
dp83640: Only wait for timestamps for packets with timestamping enabled.
ptp: Change ptp_class to a proper bitmask
dp83640: Prune rx timestamp list before reading from it
dp83640: Delay scheduled work.
dp83640: Include hash in timestamp/packet matching
ipv6: fix tunnel error handling
net/mlx5e: Fix LSO vlan insertion
net/mlx5e: Re-eanble client vlan TX acceleration
net/mlx5e: Return error in case mlx5e_set_features() fails
net/mlx5e: Don't allow more than max supported channels
...
* L3 and SoC support for xgene_edac. (Loc Ho)
* AMD F15h, models 0x60-6f support to amd64_edac. (Aravind Gopalakrishnan)
* Fixes and cleanups all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ek5l
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"A bunch of fixes all over the place and some hw enablement this time.
- Convert EDAC to debugfs wrappers and make drivers use those
(Borislav Petkov)
- L3 and SoC support for xgene_edac (Loc Ho)
- AMD F15h, models 0x60-6f support to amd64_edac (Aravind
Gopalakrishnan)
- Fixes and cleanups all over the place"
* tag 'edac_for_4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (22 commits)
EDAC: Fix PAGES_TO_MiB macro misuse
EDAC, altera: SoCFPGA EDAC should not look for ECC_CORR_EN
EDAC: Use edac_debugfs_remove_recursive()
EDAC, ppc4xx_edac: Fix module autoload for OF platform driver
Documentation/EDAC: Add reference documents section for amd64_edac
EDAC, amd64_edac: Update copyright and remove changelog
EDAC, amd64_edac: Extend scrub rate support to F15hM60h
EDAC: Don't allow empty DIMM labels
EDAC: Fix sysfs dimm_label store operation
EDAC: Fix sysfs dimm_label show operation
arm64, EDAC: Add L3/SoC DT subnodes to the APM X-Gene SoC EDAC node
EDAC, xgene: Add SoC support
EDAC, xgene: Fix possible sprintf() overflow issue
EDAC, xgene: Add L3 support
EDAC, Documentation: Update X-Gene EDAC binding for L3/SoC subnodes
EDAC, sb_edac: Fix TAD presence check for sbridge_mci_bind_devs()
EDAC, ghes_edac: Remove redundant memory_type array
EDAC, xgene: Convert to debugfs wrappers
EDAC, i5100: Convert to debugfs wrappers
EDAC, altera: Convert to debugfs wrappers
...
After discussing on the mailing list it turns out that
accessing the flash memory from the kernel can disrupt CPU
sleep states and CPU hotplugging, so let's disable this
DT node by default. Setups that want to access the flash
can modify this entry to enable the flash again.
Quoting Sudeep Holla: "the firmware assumes the flash is
always in read mode while Linux leaves NOR flash in
"read id" mode after initialization."
Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Lorenzo Pieralisi <Lorenzo.Pieralisi@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Leif Lindholm <leif.lindholm@arm.com>
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Fixes: 5078f77e14 "ARM64: juno: add NOR flash to device tree"
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
updates the bindings documents and dtsi file according to the review
comments[https://lkml.org/lkml/2015/9/21/670] from Rob Herring <robh@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable building all dtb files when CONFIG_OF_ALL_DTBS is enabled. The dtbs
are not really dependent on a platform being enabled or any other kernel
config, so for testing coverage it is convenient to build all of the dtbs.
This builds all dts files in the tree, not just targets listed. This
is simpler for arm64 which has a bunch of sub-dirs.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
* 'for-upstream/juno-pcie' of git://linux-arm.org/linux-ld:
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
Signed-off-by: Olof Johansson <olof@lixom.net>
Juno R1 board sports a functional PCIe host bridge that is
compliant with the SBSA standard found [1] here. With the right
firmware that initialises the XpressRICH3 controller one can
use the generic Host Bridge driver to use the PCIe hardware.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
[1] http://infocenter.arm.com/help/topic/com.arm.doc.den0029a/
This patch adds the LS2080a DTS files for QDS and RDB boards
which support the LS2080a SoC.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch updates the LS2080a simulator DTS to add support of various
peripherals which are supported on the simulator platform and explicitly
disables those which are yet not supported on the platform.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Checkpatch complains about the text suggesting writing to
Free Software Foundation for GPLv2 license copy.
This patch removes the same from the .dtsi and .dts
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch updates the LS2080a DTSI (DTS Include) file to add
support for the following peripherals:
- USB 3.0 Host
- PMU
- CCN-504
- SATA
- SPI
- PCIe
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Freescale is renaming the LS2085A SoC to LS2080A. This patch
addresses the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Freescale will be a spinning-out a set of ARMv8 based SoCs which
will be based on a similar overall SoC architecture. So, this patch
converts the existing infrastructure in the arm64/dts, arm64/Kconfig
and arm64/configs to use the generic convention ARCH_LAYERSCAPE
in place of the more specific FSL_LS2085A, to save code duplication
later-on.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add spi DTS node to the mt8173 and mt8173-evb.
Add dts nodes for the subsystem clocks on mt8173.
This includes mmsys, imgsys, vdecsys, vencsys, vencltsys.
Add clock nodes to the scpsys binding, which are needed to
access the registers of venc and venc_lt power domains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=laqA
-----END PGP SIGNATURE-----
Merge tag 'v4.3-next-arm64' of https://github.com/mbgg/linux-mediatek into next/arm64
Correct i2c DTS node names in mt8173.dtsi.
Add spi DTS node to the mt8173 and mt8173-evb.
Add dts nodes for the subsystem clocks on mt8173.
This includes mmsys, imgsys, vdecsys, vencsys, vencltsys.
Add clock nodes to the scpsys binding, which are needed to
access the registers of venc and venc_lt power domains.
* tag 'v4.3-next-arm64' of https://github.com/mbgg/linux-mediatek:
arm64: dts: mt8173: Add clocks for SCPSYS unit
arm64: dts: mt8173: Add subsystem clock controller device nodes
arm64: dts: Add spi bus dts
arm64: mt8173.dtsi: correct i2c node names
Signed-off-by: Olof Johansson <olof@lixom.net>
The keyboard driver for GPIO buttons(gpio-keys) checks for one of the
two boolean properties to enable gpio buttons as wakeup source:
1. "wakeup-source" or
2. the legacy "gpio-key,wakeup"
However juno, ste-snowball and emev2-kzm9d dts file have a undetected
"wakeup" property to indictate the wakeup source.
This patch fixes it by making use of "wakeup-source" property.
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Simon Horman <horms@verge.net.au>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add RNG device tree node
* Add MSM8x16 serial UART1 node
* Enable eMMC on apq8016-sbc board
* Fix I2C pinconf sleep state function
* Add MSM8916 I2C nodes
* Enable I2C busses on LS and HS on APQ8016-sbc
* Enable SPI busses on LS and HS on APQ8016-sbc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pMvh
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-4.4' of git://codeaurora.org/quic/kernel/agross-msm into next/dt
Pull "Qualcomm ARM64 Updates for v4.4" from Andy Gross:
* Add RNG device tree node
* Add MSM8x16 serial UART1 node
* Enable eMMC on apq8016-sbc board
* Fix I2C pinconf sleep state function
* Add MSM8916 I2C nodes
* Enable I2C busses on LS and HS on APQ8016-sbc
* Enable SPI busses on LS and HS on APQ8016-sbc
* tag 'qcom-arm64-for-4.4' of git://codeaurora.org/quic/kernel/agross-msm:
arm64: dts: apq8016-sbc: enable spi buses on LS and HS
arm64: dts: apq8016-sbc: enable i2c buses on LS and HS
arm64: dts: qcom: Add msm8916 I2C nodes.
arm64: dts: fix i2c pinconf sleep state function
arm64: dts: qcom: Enable eMMC on apq8016-sbc board
arm64: dts: qcom: Add 8x16 Serial UART1 node
arm64: dts: qcom: Add RNG device tree node
1. SRAM, MHU mailbox and SCPI support
2. CPU topology using cpu-map
3. Clock support for all the cpus
4. Support for SoC sensors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wBcv
-----END PGP SIGNATURE-----
Merge tag 'juno-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt
Merge "SCPI support on ARM64 Juno Development Platform" from Sudeep Holla:
1. SRAM, MHU mailbox and SCPI support
2. CPU topology using cpu-map
3. Clock support for all the cpus
4. Support for SoC sensors
* tag 'juno-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: Add sensor node to Juno dt
arm64: dts: add clock support for all the cpus
arm64: dts: add CPU topology on Juno
arm64: dts: add SRAM, MHU mailbox and SCPI support on Juno
The Juno motherboard has a NOR flash on the motherboard, enable
this to be accessed with the CFI flash driver. Results after
enabling MTD, MTD_CFI, MTD_PHYSMAP, MTD_PHYSMAP_OF,
MTD_CFI_INTELEXT:
8000000.flash: Found 2 x16 devices at 0x0 in 32-bit bank.
Manufacturer ID 0x000089 Chip ID 0x008919
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Using buffer write method
Using auto-unlock on power-up/resume
cfi_cmdset_0001: Erase suspend on write enabled
erase region 0: offset=0x0,size=0x40000,blocks=255
erase region 1: offset=0x3fc0000,size=0x10000,blocks=4
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 9ccd608070 "arm64: dts: add device tree for ARM SMM-A53x2 on
LogicTile Express 20MG" added a new dts file to arch/arm64 which
included "../../../../arm/boot/dts/vexpress-v2m-rs1.dtsi", i.e. a
.dtsi supplied by arch/arm.
Unfortunately this causes some issues for the split device tree
repository[0], since things get moved around there. In that context
the new .dts ends up at src/arm64/arm/vexpress-v2f-1xv7-ca53x2.dts
while the include is at src/arm/vexpress-v2m-rs1.dtsi.
The sharing of the .dtsi is legitimate since the baseboard is the same
for various vexpress systems whatever processor they use.
Previously I attempted to resolve this by creating a shared location
for such things but we have been unable to come to a consensus on
where that should be.
Instead this patch simply replaces the use of ../../ in the dts
/include/ with a symlink in arch/arm64/boot/dts/arm pointing to the
file arch/arm/boot/dts.
Since the split device tree repo will shortly be required to flatten
symlinks for other reasons this will cause the dtsi file to appear in
both src/arm and src/arm64 in the split repo, which is an improvement
on not building for arm64 now.
[0] https://git.kernel.org/cgit/linux/kernel/git/devicetree/devicetree-rebasing.git/
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Kristina Martsenko <kristina.martsenko@arm.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Frank Rowand <frank.rowand@sonymobile.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: arm@kernel.org
Cc: linux-kbuild@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add clocks needed by Mediatek VENC and VENC_LT power domianis.
These clocks were needed by accessing subsystem's registers,
so they need to be enabled before power on these subsystems.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch enables spi buses on low speed and high speed expansion
connectors on DB410C
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch enables i2c buses on low speed and high speed expansion
connectors on DB410C.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch adds missing support for i2c0 and i2c6, this support is
required to connect the i2c slaves on LS expansion on DB410c.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch fixes the i2c pinctrl sleep state by changing the pinconf
function to be in gpio mode rather than i2c.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Enable the eMMC on the APQ8016 SBC board (also known as DragonBoard 410c),
so that we can use its internal storage.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch adds the nodes required to support the UART1 node on the
MSM8916 and also fixes the sleep pins function for UART2.
Signed-off-by: Andy Gross <agross@codeaurora.org>
clock controller nodes which also support power domains (gdscs') need
to have a #power-domain-cells property. Add these for gcc and mmcc
nodes of msm8974, gcc of apq8084 and msm8916.
Also update gcc and mmcc bindings for it.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
The SCP firmware on Juno provides access to SoC sensors via the
SCPI. Add the sensor nodes to the device tree to enable this support.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
This patch adds the CPU clocks so that the CPU DVFS can be enabled.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Jon Medhurst (Tixy) <tixy@linaro.org>
This patch adds CPU topology on Juno. It will be useful for ther other
IP blocks depending on this topology.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Jon Medhurst (Tixy) <tixy@linaro.org>
This patch adds support for the MHU mailbox peripheral used on Juno by
application processors to communicate with remote SCP handling most of
the CPU/system power management. It also adds the SRAM reserving the
shared memory and SCPI message protocol using that shared memory.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Jon Medhurst (Tixy) <tixy@linaro.org>
This adds BUS1 instance pinctrl for exynos7 soc.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The A57 and A53 PMUs in Juno support different events, so describe them
separately in both the Juno and Juno R1 DTs.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds all UART nodes for the Hi6220 SoC. Recently a board[1] has
been developed to standardize UART access across all the 96boards consumer
edition boards. To use this hardware on HiKey we must configure and enable
UART3. However, to ensure backward compatibility we must keep UART0 enabled
as well.
I have removed the hard coded clock index values in favor of using the ones
already defined in include/dt-bindings/clock/hi6220-clock.h.
Since UART0 needs to be soldered, it has been suggested to use the UART3 as
the default console.
This patch was boot tested on top of next-20150930, with both UART
configurations.
[1] http://www.seeedstudio.com/depot/96Boards-UART-p-2525.html?ref=newInBazaar
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add base arm64 dts for Statrix 10
- Peripheral updates for Arria10(USB,I2C,UART)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3A9d
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_for_v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
Merge "SoCFPGA DTS updates for v4.4" from Dinh Nguyen:
- Add base arm64 dts for Statrix 10
- Peripheral updates for Arria10(USB,I2C,UART)
* tag 'socfpga_dts_for_v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: Add base stratix 10 dtsi
ARM: socfpga: dts: enable USB and I2C on Arria10 SoCDK
ARM: socfpga: dts: add clock fields for I2C, UART and USB on Arria10
Add the base DTS for Altera's SoCFPGA Stratix 10 platform.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v4: Add a non-zero ranges property for /soc node
v3: change #address-cells and #size-cells to <2>
change the GIC address to 0xfffc1000
update the GIC virtual CPU reg length to 0x2000
v2: use interrupt-affinity for pmu node
This patch adds MT8173 spi bus controllers into device tree.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-and-Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Node name in device tree should describe general class of the
device. Correct incorrect i2c node names.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
The idle-states bindings mandate that the entry-method string
in the idle-states node must be "psci" for ARM v8 64-bit systems,
but the examples in the bindings report a wrong entry-method string.
Owing to this typo, some dts in the kernel wrongly defined the
entry-method property, since they likely cut and pasted the example
definition without paying attention to the bindings definitions.
This patch fixes the typo in the DT idle states bindings examples and
respective dts in the kernel so that the bindings and related dts
files are made compliant.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Howard Chen <howard.chen@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Add initial dtsi file to support Hisilicon Hip05-D02 Board with
support of CPUs in four clusters and each cluster has quard Cortex-A57.
Also add dts file to support Hip05-D02 development board.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The Hisilicon Network Subsystem is a long term evolution IP which is
supposed to be used in Hisilicon ICT SoC. The IP, which is called hns
for short, is a TCP/IP acceleration engine, which can directly decode
TCP/IP stream and distribute them to different ring buffers.
HNS can be configured to work on different mode for different scenario.
This patch make use only some of the mode to make it as standard
ethernet NIC. The other mode will be added soon.
The whole function has 4 kernel sub-modules:
hnae: the HNS acceleration engine framework. It provides a abstract
interface between the engine and the upper layers which make use of the
engine by ring buffer.
hns_enet_drv: a standard ethernet driver that base on the ring buffer.
hns_dsaf: one of the implementation of HNS acceleration engine, which is
applied on Hililicon hip05, Hi1610 and other later-on SoCs
hns_mdio: the mdio control to the PHY, used by acceleration engine
This submit add basic config and documents
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds dts for the Berlin4CT STB reference board which is also
based on the Berlin4CT SoC. The Berlin4CT DMP board will be deprecated as
time goes.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Marvell berlin4ct SoC has 6 GPIO ports powered by snps,dw-apb-gpio. This
patch adds the corresponding device tree nodes.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The linux,pci-probe-only property mandates an argument to indicate whether
or not to engage the "probe-only" mode, but the Seattle DTS just provides a
naked property, which is illegal.
Also, it turns out that the board is perfectly happy without probe-only, so
let's drop this altogether.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
This patch adds:
+ poweroff button device node to support poweroff by
power button on APM X-Gene 2 Merlin platform.
+ syscon poweroff device node to support poweroff feature
on APM X-Gene 2 Merlin platform
Signed-off-by: Duc Dang <dhdang@apm.com>
This patch add dts nodes for X-Gene v2 (APM X-Gene Shadowcat SoC)
platforms to use generic SYSCON regmap reset driver for its reset
operation.
Signed-off-by: Duc Dang <dhdang@apm.com>
This patch adds the support for APM Merlin board. The Merlin board
is based on the APM X-Gene Shadowcat SoC. This DTS enables PMU,
Ethernet, SATA and Serial.
[dhdang: remove pcie0 node]
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Duc Dang <dhdang@apm.com>
This patch adds syscon poweroff device node to support poweroff feature
on APM X-Gene Mustang platform
Signed-off-by: Tai Nguyen <ttnguyen@apm.com>
Tested-by: dann frazier <dann.frazier@canoncial.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
This patch add dts nodes for X-Gene platforms to use
generic SYSCON regmap reset driver for its reset operation.
[dhdang: changelog]
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Duc Dang <dhdang@apm.com>
Adding the second 10GbE dt node for APM X-Gene SoC device tree
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Support for new architectural features introduced in ARMv8.1:
* Privileged Access Never (PAN) to catch user pointer dereferences in
the kernel
* Large System Extension (LSE) for building scalable atomics and locks
(depends on locking/arch-atomic from tip, which is included here)
* Hardware Dirty Bit Management (DBM) for updating clean PTEs
automatically
- Move our PSCI implementation out into drivers/firmware/, where it can
be shared with arch/arm/. RMK has also pulled this component branch
and has additional patches moving arch/arm/ over. MAINTAINERS is
updated accordingly.
- Better BUG implementation based on the BRK instruction for trapping
- Leaf TLB invalidation for unmapping user pages
- Support for PROBE_ONLY PCI configurations
- Various cleanups and non-critical fixes, including:
* Always flush FP/SIMD state over exec()
* Restrict memblock additions based on range of linear mapping
* Ensure *(LIST_POISON) generates a fatal fault
* Context-tracking syscall return no longer corrupts return value when
not forced on.
* Alternatives patching synchronisation/stability improvements
* Signed sub-word cmpxchg compare fix (tickled by HAVE_CMPXCHG_LOCAL)
* Force SMP=y
* Hide direct DCC access from userspace
* Fix EFI stub memory allocation when DRAM starts at 0x0
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV5XXWAAoJELescNyEwWM0p4UIAIQwgoUnj01LvtImjMyG0NiY
38GbAia7FsyIktSjuCaEhLsWjL8WSMscRsz6MLK01ir3iOoKdtXd/OptlsJTV5c5
5POPAU6hvdfKj6MtsaOAOx4dz7bhM/HB9JSZmcbHqytOxIi4Tp1JoBrmM1mpNwmp
VFy+GAOs5H6Lb/xUMm50pVUx+mjMXsH4Bo1c/0Y/gYsjhcvcRgE2iqnl7UExgDcW
5sbhpsdw8zleDx+kzTmt5QoFWk/4l3d/F+0dzLCYfxzCLNYacksbQqEbGFVAsiIl
aACK3Uqk7v7ZtFqqQLtNzE6Pfiw0CzajINPUyykoMCnDtMsyhYbxqezywCAPpSY=
=8qHf
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
- Support for new architectural features introduced in ARMv8.1:
* Privileged Access Never (PAN) to catch user pointer dereferences in
the kernel
* Large System Extension (LSE) for building scalable atomics and locks
(depends on locking/arch-atomic from tip, which is included here)
* Hardware Dirty Bit Management (DBM) for updating clean PTEs
automatically
- Move our PSCI implementation out into drivers/firmware/, where it can
be shared with arch/arm/. RMK has also pulled this component branch
and has additional patches moving arch/arm/ over. MAINTAINERS is
updated accordingly.
- Better BUG implementation based on the BRK instruction for trapping
- Leaf TLB invalidation for unmapping user pages
- Support for PROBE_ONLY PCI configurations
- Various cleanups and non-critical fixes, including:
* Always flush FP/SIMD state over exec()
* Restrict memblock additions based on range of linear mapping
* Ensure *(LIST_POISON) generates a fatal fault
* Context-tracking syscall return no longer corrupts return value when
not forced on.
* Alternatives patching synchronisation/stability improvements
* Signed sub-word cmpxchg compare fix (tickled by HAVE_CMPXCHG_LOCAL)
* Force SMP=y
* Hide direct DCC access from userspace
* Fix EFI stub memory allocation when DRAM starts at 0x0
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (92 commits)
arm64: flush FP/SIMD state correctly after execve()
arm64: makefile: fix perf_callchain.o kconfig dependency
arm64: set MAX_MEMBLOCK_ADDR according to linear region size
of/fdt: make memblock maximum physical address arch configurable
arm64: Fix source code file path in comments
arm64: entry: always restore x0 from the stack on syscall return
arm64: mdscr_el1: avoid exposing DCC to userspace
arm64: kconfig: Move LIST_POISON to a safe value
arm64: Add __exception_irq_entry definition for function graph
arm64: mm: ensure patched kernel text is fetched from PoU
arm64: alternatives: ensure secondary CPUs execute ISB after patching
arm64: make ll/sc __cmpxchg_case_##name asm consistent
arm64: dma-mapping: Simplify pgprot handling
arm64: restore cpu suspend/resume functionality
ARM64: PCI: do not enable resources on PROBE_ONLY systems
arm64: cmpxchg: truncate sub-word signed types before comparison
arm64: alternative: put secondary CPUs into polling loop during patch
arm64/Documentation: clarify wording regarding memory below the Image
arm64: lse: fix lse cmpxchg code indentation
arm64: remove redundant object file list
...
Here's our branch of ARM64 contents for this merge window.
Most of this is DT contents for new SoCs (or those who have seen new
device support added). Maybe we should stop separating out the arm64
contents here to avoid the kind of internal conflicts as we got this
time around, where 32- and 64-bit contents conflicted.
Anyhow, on the actual contents:
New SoCs:
- Broadcom North Star 2 (ns2)
- Marvell Berlin4CT
- Mediatek MT6795
- Rockchip RK3368
In addition, there are enhancements for the following platforms:
- Mediatek MT8173: cpuidle-dt updates, misc other additions
- ZyncMP: A bunch of devices added to the existing DTSI
- Qualcomm MSM8916 and APQ8016 updates for USB, etc.
+ A handful of other updates for various platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SZR9
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit changes from Olof Johansson:
"Here's our branch of ARM64 contents for this merge window.
Most of this is DT contents for new SoCs (or those who have seen new
device support added). Maybe we should stop separating out the arm64
contents here to avoid the kind of internal conflicts as we got this
time around, where 32- and 64-bit contents conflicted.
Anyhow, on the actual contents:
New SoCs:
- Broadcom North Star 2 (ns2)
- Marvell Berlin4CT
- Mediatek MT6795
- Rockchip RK3368
In addition, there are enhancements for the following platforms:
- Mediatek MT8173: cpuidle-dt updates, misc other additions
- ZyncMP: A bunch of devices added to the existing DTSI
- Qualcomm MSM8916 and APQ8016 updates for USB, etc.
+ a handful of other updates for various platforms"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (47 commits)
ARM64: dts: vexpress: Use assigned-clock-parents for sp810
ARM64: dts: mt6795: enable basic SMP bringup for MT6795
arm64: Enable Marvell Berlin SoC family in defconfig
arm64: Enable Marvell Berlin SoC family in Kconfig
arm64: dts: Add dts files for Marvell Berlin4CT SoC
ARM64: zynqmp: Move SPI nodes to the right location
ARM64: zynqmp: Move uart and ttcs to the right location
ARM64: zynqmp: Enable spi flashes on ep108
ARM64: zynqmp: Add eeprom memories on i2c bus
ARM64: zynqmp: Enable sdhci on ep108
ARM64: zynqmp: Enable watchdog on ep108
ARM64: zynqmp: Add DWC3 usb support
ARM64: zynqmp: Add SMMU support
ARM64: zynqmp: Add CANs node for platform
ARM64: zynqmp: Use zynqmp specific compatible string for gpio
devicetree: xilinx: zynqmp: add sata node
PCI: iproc: Fix BCMA dependency in Kconfig
arm64: dts: Add Broadcom North Star 2 support
arm64: Add Broadcom iProc family support
PCI: iproc: Fix ARM64 dependency in Kconfig
...
The sp810 clk driver is calling the clk consumer APIs from
clk_prepare ops to change the parent to a 1 MHz fixed rate clock
for each of the clocks that the driver provides. Use
assigned-clock-parents for this instead of doing it in the driver
to avoid using the consumer API in provider code. This also
allows us to remove the usage of clk provider APIs that take a
struct clk as an argument from the sp810 driver.
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds support SMP on MediaTek MT6795 Cortex-A53 Octa-core SoC.
Signed-off-by: Scott Shu <scott.shu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
- Add SATA, GPIO, CAN, SMMU, USB, SPI, I2C, watchdog and sdhci for zynqmp
- Sort nodes in dtsi
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlW7NiYACgkQykllyylKDCFz8wCbB/0BmJJ/iDNsR8U9r4ldT2UH
w5sAnjQCR5NaKP8J/bte07qROf7HKuKj
=beNz
-----END PGP SIGNATURE-----
Merge tag 'zynqmp-dt-for-4.3' of https://github.com/Xilinx/linux-xlnx into next/arm64
arm: Xilinx ZynqMP dt patches for v4.3
- Add SATA, GPIO, CAN, SMMU, USB, SPI, I2C, watchdog and sdhci for zynqmp
- Sort nodes in dtsi
* tag 'zynqmp-dt-for-4.3' of https://github.com/Xilinx/linux-xlnx:
ARM64: zynqmp: Move SPI nodes to the right location
ARM64: zynqmp: Move uart and ttcs to the right location
ARM64: zynqmp: Enable spi flashes on ep108
ARM64: zynqmp: Add eeprom memories on i2c bus
ARM64: zynqmp: Enable sdhci on ep108
ARM64: zynqmp: Enable watchdog on ep108
ARM64: zynqmp: Add DWC3 usb support
ARM64: zynqmp: Add SMMU support
ARM64: zynqmp: Add CANs node for platform
ARM64: zynqmp: Use zynqmp specific compatible string for gpio
devicetree: xilinx: zynqmp: add sata node
Signed-off-by: Olof Johansson <olof@lixom.net>
Add initial dtsi file to support Marvell Berlin4CT SoC with
quad Cortex-A53 CPUs.
It also adds dts file for Marvell Berlin4CT DMP board which is
based on Berlin4CT SoC.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
We had a regression due to reuse of descriptor so we have reverted that.
Rest are driver fixes
at_hdmac and at_xdmac for residue, trannfer width, and channel config
pl330 final fix for dma fails and overflow issue
xgene resouce map fix
mv_xor big endian op fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=X0jd
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.2-rc5' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"We had a regression due to reuse of descriptor so we have reverted
that.
The rest are driver fixes:
- at_hdmac and at_xdmac for residue, trannfer width, and channel config
- pl330 final fix for dma fails and overflow issue
- xgene resouce map fix
- mv_xor big endian op fix"
* tag 'dmaengine-fix-4.2-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
Revert "dmaengine: virt-dma: don't always free descriptor upon completion"
dmaengine: mv_xor: fix big endian operation in register mode
dmaengine: xgene-dma: Fix the resource map to handle overlapping
dmaengine: at_xdmac: fix transfer data width in at_xdmac_prep_slave_sg()
dmaengine: at_hdmac: fix residue computation
dmaengine: at_xdmac: fix bug about channel configuration
dmaengine: pl330: Really fix choppy sound because of wrong residue calculation
dmaengine: pl330: Fix overflow when reporting residue in memcpy
There is an overlap in dma ring cmd csr region due to sharing of ethernet
ring cmd csr region. This patch fix the resource overlapping by mapping
the entire dma ring cmd csr region.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The patch:
"gpio: Added support to Zynq Ultrascale+ MPSoC"
(sha1: bdf7a4ae37)
added zynqmp specific features. This patch is switching the driver to
use the zynqmp compatible string.
Also enable the driver for ep108 platform.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
add sata node with sata fixed clock nodes in dtsi file.
enable sata in zynqmp-ep108.dts with broken-gen2.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add Broadcom NS2 device tree binding document. Also add initial device
tree dtsi for Broadcom North Star 2 (NS2) SoC and board support for NS2
SVK board
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
APQ8016 SBC board have 6 user controllable LED's.
Add following devices:
LED1 green LED triggered by system heartbeat.
LED2 green LED triggered by access to eMMC device.
LED3 green LED triggered by access to SD card.
LED4 green LED no trigger assigned.
LED5 yellow LED triggered by access to WLAN.
LED6 blue LED triggered by access to Bluetooth.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
USB2513B HUB reset line is connected to PMIC GPIO3 not GPIO1.
Fix TC7USB40MU Dual SPDT Switch select input line control, which is
connected to PMIC GPIO4 not GPIO2 and disable the pin. It is not used
for now.
Remove user LEDs definitions, because they clash with above numbers.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Hogging pins from pinctrl driver prevents client drivers
to probe.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add sdhci1 and sdhci2 device configuration nodes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add device nodes for SPI1, SPI2, SPI3, I2C4, SPI5, SPI6 and
BAM(DMA) engine connected to them.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Create separate file for MSM8916 pinctrl default/sleep pins state
definitions. Move in UART2 states and add SPI, I2C and SDC configurations.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Plumb up Makefile arguments for the already supported formats in the kbuild
system: lz4, bzip2, lzma, and lzo.
Note that just as with Image.gz, these images are not self-decompressing and
the booting firmware still needs to handle decompression before launching the
kernel image.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This adds basic chip support for MT6795 SoC
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a large window (up to 64GB) for X-Gene PCIe nodes to support devices
that require huge BARs.
Each X-Gene PCIe node will now have two memory windows: a 32-bit
non-prefetchable window and a 64-bit prefetchable window.
[bhelgaas: changelog]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This adds afe (audio front end) device node to the MT8173 dtsi file.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In terms of peripherals the rk3368 is quite similar to the rk3288, which
makes it possible to have a lot basic components working in the first go.
More to follow once I tracked down all the tiny differences that still
exist in some parts.
With these dts files, the R88 board is able to boot from an attached
usb device and most likely from its emmc too, if the emmc uses a standard
partition table instead of Rockchip's own one - the emmc itself is
detected correctly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Since ETMv4 driver has been merged, this patch adds ETM nodes for SC9836,
and four funnel input ports to connect with ETM output ports.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add a DTS file for the MP2 Cortex-A53 Soft Macrocell Model implemented
on a LogicTile Express 20MG (V2F-1XV7) daughterboard. This is based on
the version that's currently available from the ARM DTS repository [1].
[1] git://linux-arm.org/arm-dts.git
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The PCIe host controller uses MSIs provided by GICv3 ITS. Enable it on
Thunder SoCs by adding an entry to DT.
Signed-off-by: Tirumalesh Chalamarla <tchalamarla@cavium.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This patch adds poweroff button device node to support poweroff feature
on APM X-Gene Mustang platform.
Signed-off-by: Y Vo <yvo@apm.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The MT8173 eval board contains a MT6397 PMIC. This adds the
corresponding device node to the dts file.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a DA9211 dual-channel BUCK regulator to i2c1.
This regulator supplies GPU and DVFS1 voltages.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds an idle-states node to describe the mt8173 idle states and
also adds references to the idle-states node in all CPU nodes.
Signed-off-by: Howard Chen <howard.chen@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds the SCPSYS device node to the MT8173 dtsi file.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add MT8173 I2C device nodes, include I2C controllers and pins.
MT8173 has six I2C controllers, from i2c0 to i2c6, exclude i2c5.
The 6th I2C controller register base doesn't next to 5th I2C,
and there is a hardware between 5th and 6th I2C controller. So
SoC designer name 6th controller as "i2c6", not "i2c5".
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
