This covers the "Disable FDI" section from the CRT mode set sequence.
This disables the FDI receiver and also the FDI pll.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This commit makes hsw_fdi_link_train responsible for implementing
everything described in the "Enable and train FDI" section from the
Hawell CRT mode set sequence documentation. We completely rewrite
hsw_fdi_link_train to match the documentation and we also call it in
the right place.
This patch was initially sent as a series of tiny patches fixing every
little problem of the function, but since there were too many patches
fixing the same function it got a little difficult to get the "big
picture" of how the function would be in the end, so here we amended
all the patches into a single big patch fixing the whole function.
Problems we fixed:
1 - Train Haswell FDI at the right time.
We need to train the FDI before enabling the pipes and planes, so
we're moving the call from lpt_pch_enable to haswell_crtc_enable
directly.
We are also removing ironlake_fdi_pll_enable since the PLL
enablement on Haswell is completely different and is also done
during the link training steps.
2 - Use the right FDI_RX_CTL register on Haswell
There is only one PCH transcoder, so it's always _FDI_RXA_CTL.
Using "pipe" here is wrong.
3 - Don't rely on DDI_BUF_CTL previous values
Just set the bits we want, everything else is zero. Also
POSTING_READ the register before sleeping.
4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train
According to the mode set sequence documentation, this is the
right place. According to the FDI_RX_TUSIZE register description,
this is the value we should set.
Also remove the code that sets this register from the old
location: lpt_pch_enable.
5 - Properly program FDI_RX_MISC pwrdn lane values on HSW
6 - Wait only 35us for the FDI link training
First we wait 30us for the FDI receiver lane calibration, then we
wait 5us for the FDI auto training time.
7 - Remove an useless indentation level on hsw_fdi_link_train
We already "break" when the link training succeeds.
8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE
When we fail the training.
9 - Change Haswell FDI link training error messages
We shouldn't call DRM_ERROR when still looping through voltage
levels since this is expected and not really a failure. So in this
commit we adjust the error path to only DRM_ERROR when we really
fail after trying everything.
While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since
it's what we use everywhere.
10 - Try each voltage twice at hsw_fdi_link_train
Now with Daniel Vetter's suggestion to use "/2" instead of ">>1".
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Applied tiny bikesheds:
- mention in comment that we test each voltage/emphasis level twice
- realing arguments of the only untouched reg write, it spilled over
the 80 char limit ...]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to set the timing override chicken bit after fdi link training
has completed and before we enable the transcoder. We also have to
clear that bit again after disabling the pch transcoder.
See "Graphics BSpec: vol4g North Display Engine Registers [IVB],
Display Mode Set Sequence" and "Graphics BSpec: vol4h South Display
Engine Registers [CPT, PPT], South Display Engine Transcoder and FDI
Control, Transcoder Debug and DFT, TRANS_CHICKEN_2" bit 31:
"Workaround : Enable the override prior to enabling the transcoder.
Disable the override after disabling the transcoder."
While at it, use the _PIPE macro for the other TRANS_DP register.
v2: Keep the w/a as-is, but kill the original (but wrongly placed)
workaround introduced in
commit 3bcf603f6d
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Jul 27 11:51:40 2011 -0700
drm/i915: apply timing generator bug workaround on CPT and PPT
and
commit d4270e57ef
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Oct 11 10:43:02 2011 -0700
drm/i915: export a CPT mode set verification function
Note that this old code has unconditionally set the w/a, which might
explain why fdi link training sometimes silently fails, and especially
why the auto-train did not seem to work properly.
v3: Paulo Zanoni pointed out that this workaround is also required on
the LPT PCH. And Arthur Ranyan confirmed that this workaround is
requierd for all ports on the pch, not just DP: The important part
is that the bit is set whenever the pch transcoder is enabled, and
that it is _not_ set while the fdi link is trained. It is also
important that the pch transcoder is fully disabled, i.e. we have to
wait for bit 30 to clear before clearing the w/a bit.
Hence move to workaround into enable/disable_transcoder, where the pch
transcoder gets enabled/disabled.
v4: Whitespace changes dropped.
v5: Don't run the w/a on IBX, we only need it on CPT/PPT and LPT.
v6:
- resolve conflicts with Paulo's big hsw vga rework
- s/!IBX/CPT since hsw paths are now all separate, and Paulo's patch
to implement the equivalent w/a for LPT is already merged.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Arthur Ranyan <arthur.j.runyan@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v5)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v5)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They are all written for a specific north disaplay->pch combination.
So stop pretending otherwise.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This essentially reverts
commit cb0953d734
Author: Adam Jackson <ajax@redhat.com>
Date: Fri Jul 16 14:46:29 2010 -0400
drm/i915: Initialize LVDS and eDP outputs before anything else
simply because it doesn't scale: It misses SDVO and DVO panels,
and now with DDI encoders on haswell this is becoming unmanageable.
Instead we simply sort the connector list after everything is
set up.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Haswell/LPT we must disable the PCH transcoder before we disable
the FDI, so don't check for disabled FDI there.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function is only for the previous gens.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These workarounds are documented on the CRT mode set sequence.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of PIPECONF_INTERLACE_MASK.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: applied the change by hand due to patch reorder.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That function is made for IBX. Running it on LPT will trigger tons of
"unclaimed register" errors. The only port remaining on LPT is
PCH_ADPA.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because we already set all the bits we can set.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: apply by hand due to dropped patch. Also, obey my OCD a bit
and do a s/_TRANSACONF/TRANSCONF(TRANSCODER_A)/, makes it more
consisten with other lpt pch code imnsho ...]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of using "pipe". As already explained in previous commits,
since Haswell/LPT cpu_transcoder, pch_transcoder and pipe are not the
same thing.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These asserts are specific to IBX/CPT/PPT. Inside the assert_pch_pll
function we even "return" in case we detect LPT, but I prefer to just
not call it. In the future we might rename to something like
ibx_assert_pch_pll.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since now we have lpt_enable_pch_transcoder.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For now the new functions are just copies. Differences will be added
later.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To ironlake_{en,dis}able_pch_transcoder since these functions will be
different on Haswell/LPT and since the "transcoder" they {en,dis}able
is on the PCH.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: again a small conflict because the fdi disable sequenc looks
a bit different here.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Haswell/LPT, pipe, cpu_transcoder and pch_transcoder are different
things with different values, unlinke the previous gens. So here we
use the right thing at the right place.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: apply the patch by hand due to the reorder patch sequence. We
also can't kill all uses of pipe where we should, since the fdi link
train code isn't fixed up yet on this baselin.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no LVDS, so don't poke the LVDS registers.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is just wrong. The lpt_program_iclkip should disable the PCH
pixel clocks (and yes, we plan to rename it later).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because this function is only for the older PCHs, not the newer ones.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since this function will only run on Haswell/LPT and newer.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since now we have lpt_pch_enable for them.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For now it's just a fork of ironlake_pch_enable. The next commits will
change this.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Makes more sense to group the entire mode_set stage into one function.
Noticed while discussiing the rather confusing set of function names
with Paulo Zanoni. Unfortunately I don't have an idea to make the
function names lesss confusion.
v2: Use for_each_encoder_on_crtc as suggested by Chris Wilson.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Refactor the code that stores the panning x/y position into the sarea.
This also changes the code so that it won't mistakenly update
sareaB_x/y for pipe >= C.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current code can't deal with framebuffers with an offset. Return an
error when trying to create such a framebuffer until the rest of the
code is fixed to handle them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure the the framebuffer stride is smaller than 32k. That
seems to be the limit on recent hardware. Not quite sure if
<=Gen4 has smaller limits.
Also when using a tiled memory make sure the object stride matches
the framebuffer stride.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix support for all RGB/BGR pixel formats (except the 16:16:16:16 float
format).
Fix intel_init_framebuffer() to match hardware and driver limitations:
* RGB332 is not supported at all
* CI8 is supported
* XRGB1555 & co. are supported on Gen3 and earlier
* XRGB210101010 & co. are supported from Gen4 onwards
* BGR formats are supported from Gen4 onwards
* YUV formats are supported from Gen5 onwards (driver limitation)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were writing DSP_ADDR and DSP_SURF unconditionally. This did not
trigger an unclaimed write before HSW as the address of DSP_ADDR has
been repurposed as DSP_LINOFF.
On HSW, though, DSP_LINOFF has been removed and then writting to it
triggers an unclaimed write.
This patch writes to DSP_ADDR or DSP_SURF to flush the display plane
configuration depending on the gen we're running on.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like in:
commit c2c7513124
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 5 12:17:30 2012 +0200
drm/i915: adjust framebuffer base address on gen4+
but this time, for the sprite planes. This ensures that the
sprite offset are always inside the supported hardware limits since it
becomes the offset into a page and we adjust the base address to a page
boundary.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And properly toggle the chicken bit in the pch to enable/disable fdi C
rx. If we don't set this bit correctly, the rx gets confused in link
training, which can result in an fdi link that silently fails to train
the link (since the corresponding register reports success). Note that
both fdi link B and C can suffer when this bit is not set correctly.
The code as-is has a few deficiencies:
- We presume all pipes use the pch which is not the case for cpu edp.
- We don't bother with disabling both pipes when we could make things
work, e.g. when pipe B switched from 4 to 2 lanes due to a mode
change, we don't bother updating the w/a bit.
- It's ugly.
All of these are because we compute ->fdi_lanes way too late, when
we're already setting up individual pipes. We need to have this
information in ->modeset_global_resources already, to set things up
correctly. But that is a much larger reorg of the code.
Note that we actually hit the 2 lanes limit in practice rather
quickly: Even though the 1920x1200 mode native mode of my screen fits
into 2 lanes, it needs 3 lanes for the 1920x1080 (since that somehow
has much more blanking ...). Not obeying this restriction seems to
results in cute-looking digital noise.
v2: Only ever clear the chicken bit when both pipes are off.
v3: Use the new ->modeset_global_resources callback.
v4: Move the WARNs to the right place. Oh how I hate hacks.
v5: Fix spelling, noticed by Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After all relevant pipes are disabled and after we've updated all the
state with the staged state, but before we call the per-crtc
->mode_set functions there's a very natural point to set up any
shared/global resources like
- shared plls (obviously only the setup, the enabling needs to be
separately handling with a separate refcount)
- global watermark state like the DSPARB on gmch platforms
- workaround bits that depend upon the exact global output
configuration
- enabling the right set of refclocks
- enabling/disabling manual power wells.
Now for a lot of these things we can't move them into this function
yet, most often because we only compute the required information in
the per-crtc ->mode_set callback. Which is too late. But due to a
bunch of reasons (check-only atomic modeset, fastboot&hw state checks,
...) we need to separate the computation of that state from the actual
hw frobbery anyway. So we can move things into this new callback step-
by-step.
Others can't be moved here (or implemented at all) because our code
lacks the smarts to properly update them. E.g. the DSPARB can only be
updated when all pipes are disabled, so if we decide to change it's
value, we need to disable _all_ pipes. The infrastructure for that is
already in place (with the various pipe masks that driver the modeset
logic). But again we need to move a few things out of ->mode_set
first before we can even implement the correct decision making.
In any case, we need to start somewhere, so let's start with the
callback: Some small follow-up patches will make immediate good use of
it.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since it is one. We need to move this code to encoder specific callbacks
eventually, to kill all that inversion of control ...
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we have a few funny issues where we enable/disable shared
pll clocks. To make it clear that we are not required to enable/
disable the pch plls together with the other pch resources (and
so should keep it running when it's used by another pipe in
a shared pll configuration) add a comment.
This note is lifted from "Graphics BSpec: vol4g North Display Engine
Registers [IVB], Display Mode Set Sequence", step 9.d. of the enable
sequence:
"Configure and enable PCH DPLL, wait for PCH DPLL warmup (Can be
done anytime before enabling PCH transcoder)."
Since fixing the pll sharing code to no longer disable shared plls
if they're still in use is more involved, let's just stick with the
comment for now.
v2: Make the comment in the code clearer, to address questions raised
by Paulo Zanoni in review.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My machine here has the correct ones already, but better safe
than sorry. IBX has different settings for that register, and
on IBX the device defaults match the recommended values. Hence
I did not add the respective writes for IBX.
LPT needs the same settings, but that has been done already
commit 4acf518626
Author: Eugeni Dodonov <eugeni.dodonov@intel.com>
Date: Wed Jul 4 20:15:16 2012 -0300
drm/i915: program FDI_RX TP and FDI delays
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For reference, see "Graphics BSpec: vol4g North Display Engine
Registers [IVB], Display Mode Set Sequence", step 4 of the enabling
sequence:
a. "Enable PCH FDI Receiver PLL, wait for warmup plus DMI latency
b. "Switch from Rawclk to PCDclk in FDI Receiver
c. "Enable CPU FDI Transmitter PLL, wait for warmup"
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to "Graphics BSpec: vol4g North Display Engine Registers [IVB],
Display Mode Set Sequence" We need to write the TU size register
of the fdi RX unit _before_ starting to train the link.
Note: The current code is actually correct as Paulo mentioned in
review, but it's a bit confusion since only the fdi rx/tx plls need to
be enabled before the cpu pipes/planes. Hence it's still a good idea
to move the TU_SIZE setting to the "right" spot in the sequence, to
better match Bspec.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel's backmerge
commit c2fb791692
Merge: 29de6ce6f0c058
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Oct 22 14:34:51 2012 +0200
Merge tag 'v3.7-rc2' into drm-intel-next-queued
to solve conflicts blew up (either git or Daniel was trying to be too
clever for their own good; it's usually convenient to blame tools ;) and
caused the changes of
commit 0c96c65b48
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Sep 26 18:43:10 2012 +0300
drm/i915: use adjusted_mode instead of mode for checking the 6bpc force flag
in ironlake_crtc_mode_set() to be dropped.
Fix the call in ironlake_crtc_mode_set() again, and while at it, also fix
the new, copy-pasted haswell_crtc_mode_set() to use adjusted_mode.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
See the documentation for the DDI_FUNC_CTL register, EDP Input Select
bits: when the EDP input selection is B, the VTOTAL_B must be
programmed with the VTOTAL_EDP value, same thing for selection C.
V2: Use I915_READ as suggested by Daniel Vetter.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same thing as the previous commits. Not renaming this one since it
exists since way before Haswell.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because the PIPECONF register is actually part of the CPU transcoder,
not the CPU pipe.
Ideally we would also rename PIPECONF to TRANSCONF to remind people
that they should use the transcoder instead of the pipe, but let's
keep it like this for now since most Gens still name it PIPECONF.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to check if any of the pipes is using TRANSCODER_EDP.
V2: DDI_BUF_CTL was renamed, so fix the usage here.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because there's one instance of the register per CPU transcoder and
not per CPU pipe. This is another register that appeared for the first
time on Haswell, and even though its Haswell name is
PIPE_DDI_FUNC_CTL, it will be renamed to TRANS_DDI_FUNC_CTL, so let's
just use the new naming scheme before it confuses more people.
Notice that there's a big improvement on intel_ddi_get_hw_state due to
the new TRANSCODER_EDP.
V2: Also rename the register to TRANS_DDI_FUNC_CTL as suggested by
Damien Lespiau.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Before Haswell we used to have the CPU pipes and the PCH transcoders.
We had the same amount of pipes and transcoders, and there was a 1:1
mapping between them. After Haswell what we used to call CPU pipe was
split into CPU pipe and CPU transcoder. So now we have 3 CPU pipes (A,
B and C), 4 CPU transcoders (A, B, C and EDP) and 1 PCH transcoder
(only used for VGA).
For all the outputs except for EDP we have an 1:1 mapping on the CPU
pipes and CPU transcoders, so if you're using CPU pipe A you have to
use CPU transcoder A. When have an eDP output you have to use
transcoder EDP and you can attach this CPU transcoder to any of the 3
CPU pipes. When using VGA you need to select a pair of matching CPU
pipes/transcoders (A/A, B/B, C/C) and you also need to enable/use the
PCH transcoder.
For now we're just creating the cpu_transcoder definitions and setting
cpu_transcoder to TRANSCODER_EDP on DDI eDP code, but none of the
registers was ported to use transcoder instead of pipe. The goal is to
keep the code backwards-compatible since on all cases except when
using eDP we must have pipe == cpu_transcoder.
V2: Comment the haswell_crtc_off chunk, suggested by Damien Lespiau
and Daniel Vetter.
We currently need the haswell_crtc_off chunk because TRANSCODER_EDP
can be used by any CRTC, so when you stop using it you have to stop
saying you're using it, otherwise you may have at some point 2 CRTCs
claiming they're using TRANSCODER_EDP (a disabled CRTC and an enabled
one), then the HW state readout code will get completely confused.
In other words:
Imagine the following case:
xrandr --output eDP1 --auto --crtc 0
xrandr --output eDP1 --off
xrandr --output eDP1 --auto --crtc 2
After the last command you could get a "pipe A assertion failure
(expected off, current on)" because CRTC 0 still claims it's using
TRANSCODER_EDP, so the HW state readout function will read it
(through PIPECONF) and expect it to be off, when it's actually on
because it's being used by CRTC 2.
So when we make "intel_crtc->cpu_transcoder = intel_crtc->pipe" we
make sure we're pointing to our own original CRTC which is certainly
not used by any other CRTC.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Ironlake we have one PCH transcoder and FDI per pipe, so we know
that if ironlake_crtc_driving_pch returns false we can disable the PCH
transcoder and we also know that when we disable the crtc we can also
disable the PCH transcoder.
On Haswell there is only 1 PCH transcoder and FDI and they can be used
by any CRTC. So if for one specific crtc haswell_crtc_driving_pch
returns false we can't assert anything about the state of the PCH
transcoder or the FDI link without checking if any other CRTC is using
the PCH.
So on this commit remove the "assert_fdi_{t,r}x_disabled" form
haswell_crtc_enable and also only disable FDI and the PCH transcoder
if the port being disabled was actually a PCH port (we only have one
port using PCH: the VGA port).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By forking Ironlake and Haswell functions. The only callers are
{ironlake,haswell}_crtc_enable anyway, and this way we won't need to
add other checks on the Haswell version for the next gens.
V2: Even simpler, as pointed by Jani Nikula.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These functions were forked from their Ironlake versions, so now fix
the gen checks to reflect the fact that they will only run on Haswell.
It is worth noticing that we are not considering IBX/CPT possible on
Haswell anymore. So far on Haswell enablement we kept trying to still
consider IBX/CPT as a possibility with a Haswell CPU, but this was
never tested, I really doubt it will work with the current code and we
don't really have plans to support it. Future patches will remove the
IBX/CPT code from other Haswell functions. Notice that we still have a
WARN on haswell_crtc_mode_set in case we detect non-LPT PCH.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The last commit forked a Haswell version, so now we remove Haswell
code from these functions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The way we enable and disable the PCH on Haswell changed considerably
since now we have only one PCH transcoder, so we can't keep the same
asserts and we also can't just unconditionally disable the PCH
transcoder for non-PCH outputs. So let's fork a Haswell version.
These new functions look exactly the same as the ironlake versions.
The next patches will introduce the differences.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this when the bios forgets even to set that bit up. Most seem
to do that, even when they don't set up anything else in the panel
power sequencer.
Note that on IBX the rawclk is variable according to Bspec, but
everyone is using 125MHz. The rawclk is fixed to 125MHz on CPT, but
luckily we still have the same register available. On hsw, different
variants have different clocks, hence we need to check the register.
Since other pieces are driven by the rawclock, too, keep the little
helper in a central place.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQgvdwAAoJEHm+PkMAQRiG+3AH/i2XsqqN3VctL0nnbWfvds+Q
aKulfIdJTjKiVAsawPUtRqReZ8ijiebrgA/53lZLlrFOoPPQ5+LHmnSyQF6gErOY
NuAE1lijXDRM1pwBlhvOBbAj26wUobGjqONFJ9OkKr758Ue8ds/Q7UdxyEgmYgmg
tvVMzfRcICzryUV3PcqL+3cNPpCUdT6wGGRJ9DCv/jvGiWKExWhOle5oltrmxk+D
NsqRcws5pEubfHE4J8BvNWr8lE1kHfYVhrJETiLJUiN2XAJcbI4Jy7rU/3EGteNS
0HMZdaPPjV874lohdM70X2225SbYrCVkAYB5hnZCTeC3tYyCawBBPMQoyAiOcmU=
=+861
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc2' into drm-intel-next-queued
Linux 3.7-rc2
Backmerge to solve two ugly conflicts:
- uapi. We've already added new ioctl definitions for -next. Do I need to say more?
- wc support gtt ptes. We've had to revert this for snb+ for 3.7 and
also fix a few other things in the code. Now we know how to make it
work on snb+, but to avoid losing the other fixes do the backmerge
first before re-enabling wc gtt ptes on snb+.
And a few other minor things, among them git getting confused in
intel_dp.c and seemingly causing a conflict out of nothing ...
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_modes.c
include/drm/i915_drm.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
The big thing is the disabling of the hsw support by default, cc: stable.
We've aimed for basic hsw support in 3.6, but due to a few bad
happenstances we've screwed up and only 3.8 will have better modeset
support than vesa. To avoid yet another round of fallout from such a
gaffle on for the next platform we've added a module option to disable
early hw support by default. That should also give us more flexibility in
bring-up.
Otherwise just small fixes:
- 3 fixes from Egbert for sdvo corner cases
- invert-brightness quirk entry from Egbert
- revert a dp link training change, it regresses some setups
- and shut up a spurious WARN in our gem fault handler.
- regression fix for an oops on bit17 swizzling machines, introduce in 3.7
- another no-lvds quirk
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Initialize obj->pages before use by i915_gem_object_do_bit17_swizzle()
drm/i915: Add no-lvds quirk for Supermicro X7SPA-H
drm/i915: Insert i915_preliminary_hw_support variable.
drm/i915: shut up spurious WARN in the gtt fault handler
Revert "drm/i915: Try harder to complete DP training pattern 1"
DRM/i915: Restore sdvo_flags after dtd->mode->dtd Roundrtrip.
DRM/i915: Don't clone SDVO LVDS with analog.
DRM/i915: Add QUIRK_INVERT_BRIGHTNESS for NCR machines.
DRM/i915: Don't delete DPLL Multiplier during DAC init.
We have to write the correct values inside intel_dp_set_m_n and then
prevent these values from being overwritten later.
V2: Unconfuse double negation.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of relying on the register save/restore madness to do this.
To extract a bit of code call drm_mode_config_reset both on resume
and boot-up and move the hw state frobbing from the crt_init to the
->reset callback. The crt connector is the only one with a ->reset
callback, hence we can easily do this.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In theory, all the DDI pipe settings should be set here, including
timing and M/N registers. For now, let's just set the DP MSA
attributes.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: fixed up the unused typo in a #define, spotted by Jani
Nikula.]
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
NCR machines with LVDS panels using Intel chipsets need to have the
QUIRK_INVERT_BRIGHTNESS bit set.
Unfortunately NCR doesn't set a meaningful subvendor/subdevice ID,
therefore we add a DMI dependent quirk list.
Signed-off-by: Egbert Eich <eich@suse.de>
[danvet: fixup whitespace fail.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
"- some register magic to fix hsw crw (Paulo&Ben)
- fix backlight destruction for cpu edp (Jani)
- fix gen ch7xxx dvo ->get_hw_state
- fixup the plane->pipe fixup code, the broken version massively angers
the modeset sanity checks
- kill pipe A quirk for i855gm, otherwise I get a black screen with the
above patch
- fixup for gem_get_page helper (Chris)
- fixup guardband clipping w/a (Ken), without this mesa master can erronously
drop vertices on snb, mesa 9.0 has the optimization reverted
- another pageflip vs. modeset fix
- kill bogus BUG_ON which broke ums+gem from Willy Tarreau (gasp, people
are still using this!)"
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: fix non-DP-D eDP backlight cleanup and module reload
drm/i915: HSW CRW stability magic
drm/i915/dvo-ch7xxx: fix get_hw_state
drm/i915: fixup the plane->pipe fixup code
drm/i915: rip out the pipe A quirk for i855gm
drm/i915: disable wc gtt pte mappings on gen2
drm/i915: fixup i915_gem_object_get_page inline helper
drm/i915: Disallow preallocation of requests
drm/i915: Set guardband clipping workaround bit in the right register.
drm/i915: paper over a pipe-enable vs pageflip race
drm/i915: remove useless BUG_ON which caused a regression in 3.5.
We need to check whether the _other plane is on our pipe, not whether
our plane is on the other pipe. Otherwise if not both pipes/planes are
active, we won't properly clean up the mess and set up our desired
plane->pipe mapping.
v2: Fixup the logic, I've totally fumbled it. Noticed by Chris Wilson.
v3: I've checked Bspec, and the flexible plane->pipe mapping is a
gen2/3 feature, so test for that instead of PCH_SPLIT
v4: Check whether we indeed have 2 pipes before checking the other
pipe, to avoid upsetting i845g/i865g. Noticed by Chris Wilson.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51265
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49838
Tested-by: Dave Airlie <airlied@gmail.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> #855gm
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This seems to be the root-cause that breaks resume on my i855gm when I
apply the "drm/i915: fixup the plane->pipe fixup code" patch. And that
code doesn't even run on my machine, so it's pure timing changes
causing the regression.
Furthermore resume has been constantly switching between working and
broken on this machine ever since kms support has been merged,
seemingly with no related change as a root cause. And always with the
same symptoms of the backlight lighting up, but the lvds panel only
displaying black.
Also, of both i855gm variants only one is in the table. And in the
past we've only ever removed entries from this quirk table because it
breaks things.
So let's just remove it - in case there's indeed a bios out there
relying on a running pipe A, we can add back in a more precise quirk
entry, like all the others (save for i830/i845).
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> #855gm
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So WARN in case they're not. It also does not make any sense to
wait_for_vblank at this point.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Problems with the previous code:
- HDMI just uses WRPLL1 for everything, so dual head cases might not
work sometimes.
- At encoder->mode_set we just write the PLL register without doing
any kind of check (e.g., check if the PLL is already being used).
- There is no way to fail and return error codes at
encoder->mode_set.
- We write to PORT_CLK_SEL at mode_set and we never disable it.
- Machines hang due to wrong clock enable/disable sequence.
So here we rewrite the code, making it a little more like the
pre-Haswell PLL mode set code:
- Check PLL availability at ironlake_crtc_mode_set.
- Try to use both WRPLLs.
- Check if PLLs are used before actually trying to use them, and
properly fail with error messages.
- Enable/disable PORT_CLK_SEL at the right place.
- Add some WARNs to check for bugs.
The next improvement will be to try to reuse PLLs if the timings
match, but this is content for another patch and it's already
documented with a TODO comment.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's a copy of ironlake_set_pipeconf with 2 differences:
- There is no BPC field to set.
- The interlaced mask is now 2 bits instead of 3.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On ironlake_crtc_mode_set, WARN if not using IBX or CPT.
On haswell_crtc_mode_set, only run IBX/CPT code on IBX/CPT. I am still
not sure whether IBX/CPT will be possible with a Haswell CPU, so leave
the code there for now and put a WARN in case we spot it.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's just a copy of ironlake_crtc_mode_set.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously we were enabling it at mode_set but never disabling. Let's
follow the mode set sequence.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And the right time is exactly after/before changing PIPE_CONF. See the
documentation about the mode set sequence.
This code is not inside any encoder-specific callback because
DDI_FUNC_CTL is part of the pipe, so it is used by all encoders.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Right now, we're trying to enable LCPLL at every mode set, but we're
never disabling it. Also, we really don't want to be disabling LCPLL
since it requires a very complex disable/enable sequence. This
register should really be set by the BIOS and we shouldn't be touching
it. Still, let's try to check its value and print some errors in case
we find something wrong. We're also adding intel_ddi_get_cdclk_freq
which will be used later in other places.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've discovered this on my ivb machine while stress-testing the new
flip_tests. Only harmful effect observed is that the timestamp is a
bit bogus.
Note that this is empirical duct-tape: I've noticed that we seem to
only ever miss the very first vblank irq right after enabling the
pipe. And with this hack applied I couldn't reproduce the failure case
anywhere else any more.
Tested-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
Bigger -fixes pile, mostly because I've included Ajax' DP dongle stuff,
as discussed on irc. Otherwise just small things:
- regression fix to finally make 6bpc auto-dither on dp work (Jani)
- reinstate an snb ctx w/a that accidentally got lost in a rework (Chris)
- fixup the DP train sequence, logic-goof-up uncovered by Coverty (Chris)
- fix set_caching locking (Ben)
- fix spurious segfault on con-current gtt mmap faulting (Dimitry and Mika)
- some pageflip correctness fixes (still hunting down some issues, but
these are the worst offenders of confused code that we've tracked down
thus far) from Chris and me
- fixup swizzling settings on vlv (Jesse)
- gt_mode w/a from Ben added, fixes snb gt1 rc6+hw ctx hangs.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Fix GT_MODE default value
drm/i915: don't frob the vblank ts in finish_page_flip
drm/i915: call drm_handle_vblank before finish_page_flip
drm/i915: print warning if vmi915_gem_fault error is not handled
drm/i915: EBUSY status handling added to i915_gem_fault().
drm/i915: Try harder to complete DP training pattern 1
drm/i915: set swizzling to none on VLV
drm/dp: Make sink count DP 1.2 aware
drm/dp: Document DP spec versions for various DPCD registers
drm/i915/dp: Be smarter about connection sense for branch devices
drm/i915/dp: Fetch downstream port info if needed during DPCD fetch
drm/dp: Update DPCD defines
drm: Export drm_probe_ddc()
drm/i915: Flush the pending flips on the CRTC before modification
drm/i915: Actually invalidate the TLB for the SandyBridge HW contexts w/a
drm/i915: Fix set_caching locking
drm/i915: use adjusted_mode instead of mode for checking the 6bpc force flag
Now that we correctly generate it, this hack is no longer required (and
might actually paper over a serious bug).
pageflip timestamps are sanity check in the latest version of the flip-test
in intel-gpu-tools.
v2: Also remove the gettimeofday(&now) which is no longer used.
Noticed by Mario Kleiner.
Reviewed-by: mario.kleiner@tuebingen.mpg.de
Tested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm merge (part 1) from Dave Airlie:
"So first of all my tree and uapi stuff has a conflict mess, its my
fault as the nouveau stuff didn't hit -next as were trying to rebase
regressions out of it before we merged.
Highlights:
- SH mobile modesetting driver and associated helpers
- some DRM core documentation
- i915 modesetting rework, haswell hdmi, haswell and vlv fixes, write
combined pte writing, ilk rc6 support,
- nouveau: major driver rework into a hw core driver, makes features
like SLI a lot saner to implement,
- psb: add eDP/DP support for Cedarview
- radeon: 2 layer page tables, async VM pte updates, better PLL
selection for > 2 screens, better ACPI interactions
The rest is general grab bag of fixes.
So why part 1? well I have the exynos pull req which came in a bit
late but was waiting for me to do something they shouldn't have and it
looks fairly safe, and David Howells has some more header cleanups
he'd like me to pull, that seem like a good idea, but I'd like to get
this merge out of the way so -next dosen't get blocked."
Tons of conflicts mostly due to silly include line changes, but mostly
mindless. A few other small semantic conflicts too, noted from Dave's
pre-merged branch.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (447 commits)
drm/nv98/crypt: fix fuc build with latest envyas
drm/nouveau/devinit: fixup various issues with subdev ctor/init ordering
drm/nv41/vm: fix and enable use of "real" pciegart
drm/nv44/vm: fix and enable use of "real" pciegart
drm/nv04/dmaobj: fixup vm target handling in preparation for nv4x pcie
drm/nouveau: store supported dma mask in vmmgr
drm/nvc0/ibus: initial implementation of subdev
drm/nouveau/therm: add support for fan-control modes
drm/nouveau/hwmon: rename pwm0* to pmw1* to follow hwmon's rules
drm/nouveau/therm: calculate the pwm divisor on nv50+
drm/nouveau/fan: rewrite the fan tachometer driver to get more precision, faster
drm/nouveau/therm: move thermal-related functions to the therm subdev
drm/nouveau/bios: parse the pwm divisor from the perf table
drm/nouveau/therm: use the EXTDEV table to detect i2c monitoring devices
drm/nouveau/therm: rework thermal table parsing
drm/nouveau/gpio: expose the PWM/TOGGLE parameter found in the gpio vbios table
drm/nouveau: fix pm initialization order
drm/nouveau/bios: check that fixed tvdac gpio data is valid before using it
drm/nouveau: log channel debug/error messages from client object rather than drm client
drm/nouveau: have drm debugging macros build on top of core macros
...
Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Version 2: call intel_set_pipe_timings from both i9xx_crtc_mode_set
and ironlake_crtc_mode_set, instead of just ironlake, as requested by
Daniel Vetter.
The problem caused by calling this function from i9xx_crtc_mode_set
too is that now on i9xx we write to PIPESRC before writing to DSPSIZE
and DSPPOS. I could not find any evidence in our documentation that
this won't work, and the docs actually say the pipe registers should
be set before the plane registers.
Version 3: don't remove pipeconf bits on i9xx_crtc_mode_set.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was meant to be the purpose of the
intel_crtc_wait_for_pending_flips() function which is called whilst
preparing the CRTC for a modeset or before disabling. However, as Ville
Syrjala pointed out, we set the pending flip notification on the old
framebuffer that is no longer attached to the CRTC by the time we come
to flush the pending operations. Instead, we can simply wait on the
pending unpin work to be finished on this CRTC, knowning that the
hardware has therefore finished modifying the registers, before proceeding
with our direct access.
Fixes i-g-t/flip_test on non-pch platforms. pch platforms simply
schedule the flip immediately when the pipe is disabled, leading
to other funny issues.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
[danvet: Added i-g-t note and cc: stable]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eventhough Valleyview display block is derived from Cantiga, VLV
supports eDP. So, added eDP checks in i9xx_crtc_mode_set path.
v2: use different DPIO_DIVISOR values for VGA, DP and eDP
v3: fix DPIO value calculation to use same values for all display
interfaces
v4: removed unconditional enabling of 6bpc dithering based on comments
from Daniel & Jani Nikula. Also changed the display enabling order to
force eDP detection first.
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In valleyview voltageswing, pre-emphasis and lane control registers can
be programmed only through the h/w side band fabric.
Cleaned up DPLL calculations for Valleyview to support multi display
configurations.
v2: Based on Daniel's feedbacak, moved crt hotplug detect work around as separate
patch. Also moved i9xx_update_pll_dividers to i8xx_update_pll and
i9xx_update_pll.
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: drop spurious whitespace changes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
m n tu register offset has changed in Valleyview. Also fixed DP limit
frequencies.
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The dithering introduced in
commit 3b5c78a35c
Author: Adam Jackson <ajax@redhat.com>
Date: Tue Dec 13 15:41:00 2011 -0800
drm/i915/dp: Dither down to 6bpc if it makes the mode fit
stores the INTEL_MODE_DP_FORCE_6BPC flag in the private_flags of the
adjusted mode, while i9xx_crtc_mode_set() and ironlake_crtc_mode_set() use
the original mode, without the flag, so it would never have any
effect. However, the BPC was clamped by VBT settings, making things work by
coincidence, until that part was removed in
commit 4344b813f1
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Aug 10 11:10:20 2012 +0200
Use adjusted_mode instead of mode when checking for
INTEL_MODE_DP_FORCE_6BPC to make the flag have effect.
v2: Don't forget to fix this in i9xx_crtc_mode_set() also, pointed out by
Daniel both before and after sending the first patch.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47621
CC: Adam Jackson <ajax@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The last patches moved a lot of code from ironlake_crtc_mode_set to
sub-functions, so these variables became useless. You could get
warnings by enabling -Wunused-but-set-variable.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Too many lines just to compute the value of a single variable, so
move this to its own function.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The set_m_n code was spread all over the mode_set function.
Version 2:
Don't set the DP M/N registers on ironlake_set_m_n. Daniel Vetter has
plans to add some encoder-specific callbacks. Also, on this version we
don't change the order we're writing the registers, making the code
change safer.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As noticed by Daniel Vetter, intel_pipe_choose_bpp_dither should
already check for invalid bpp values and set a valid value, so remove
the recheck inside ironlake_crtc_mode_set and also replace a "default"
switch case inside ironlake_set_pipeconf with a BUG().
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQX7MuAAoJEHm+PkMAQRiG0h0IAJURkrMCAQUxA+Ik66ReH89s
LQcVd0U9uL4UUOi7f5WR64Vf9Cfu6VVGX9ZKSvjpNskvlQaUQPMIt4pMe6g4X4dI
u0bApEy4XZz3nGabUAghIU8jJ8cDmhCG6kPpSiS7pi7KHc0yIa4WFtJRrIpGaIWT
xuK38YOiOHcSDRlLyWZzainMncQp/ixJdxnqVMTonkVLk0q0b84XzOr4/qlLE5lU
i+TsK3PRKdQXgvZ4CebL+srPBwWX1dmgP3VkeBloQbSSenSeELICbFWavn2ml+sF
GXi4dO93oNquL/Oy5SwI666T4uNcrRPaS+5X+xSZgBW/y2aQVJVJuNZg6ZP/uWk=
=0v2l
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc7' into drm-intel-next-queued
Manual backmerge of -rc7 to resolve a silent conflict leading to
compile failure in drivers/gpu/drm/i915/intel_hdmi.c.
This is due to the bugfix in -rc7:
commit b98b601672
Author: Wang Xingchao <xingchao.wang@intel.com>
Date: Thu Sep 13 07:43:22 2012 +0800
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug
Since this code moved around a lot in -next git put that snippet at
the wrong spot. I've tried to fix this by making the conflict explicit
by merging a version for next with:
commit 3cce574f01
Author: Wang Xingchao <xingchao.wang@intel.com>
Date: Thu Sep 13 11:19:00 2012 +0800
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug unconditionally
But that failed to solve the entire problem. To avoid pushing out
further -nightly branch to our QA where this is broken, do the
backmerge and manually add the stuff git adds to -next from the patch
in -fixes.
Note that this doesn't show up in git's merge diff (and hence is also
not handled by git rerere), which adds to the reasons why I'd like to
fix this with a verbose backmerge. The git merge diff only shows a
bunch of trivial conflicts of the "code changed in lines next to each
another" kind.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Hopefully this makes userspace slightly less confused about us
frobbing the dpms state behind its back. Yeah, it would be better
to be more careful with not changing the dpms state, but that is
quite more invasive.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... because our current set_mode implementation doesn't bother to adjust
for the dpms state, we just forcefully update it. So stop pretending that
we're better than we are and rip out this extranous call.
Note that this totally confuses userspace, because the exposed connector
property isn't actually updated ...
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because they should have been disabled when shutting down the display
pipe previously. To ensure that this is the case, add a few assserts
instead of unconditionally disabling the fdi link.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even with the old crtc helper code we should have disabled all
encoders on that pipe by now, and with the new code this would
definitely paper over a bug. We already have the necessary checks
in place in intel_disable_transcoder, so if we accidentally leave
a pch port on, this will be caught.
Hence just rip this all out.
Note that up to the patch in this giant modeset series that removes
the LVDS special case to avoid disabling LVDS in the encoder->prepare
callback ("drm/i915/lvds: ditch ->prepare special case"), this was not
the case for all outputs.
Also note that in
commit 1b3c7a47f9
Author: Zhenyu Wang <zhenyuw@linux.intel.com>
Date: Wed Nov 25 13:09:38 2009 +0800
drm/i915: Fix LVDS stability issue on Ironlake
this was already discovered independently and worked around. How I
bloody hate this entire mess of cludges piled on top of other cludges.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cpu eDP encoder has some horrible hacks to set up the DP pll at
the right time. To be able to move them to the right place, add some
more encoder callbacks so that this can happen at the right time.
LVDS has some similar funky hacks, but that would require more work
(we need to move around the pll setup a bit). Hence for now only
wire these new callbacks up for ilk+ - we only have cpu eDP on these
platforms.
v2: Bikeshed the vtable ordering, requested by Chris Wilson.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: resolved conflicts due to missing some earlier patches.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because declaring a variable in the beginning of the function, then
initializing it 100 lines later, then using it 100 lines later does
not make our code look good IMHO.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because ironlake_crtc_mode_set is a giant function that used to have
404 lines. Let's try to make it less complex/confusing.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While reworking the modeset sequence, this got lost in
commit 25c5b2665f
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jul 8 22:08:04 2012 +0200
drm/i915: implement new set_mode code flow
I've noticed this because some Xorg versions seem to set up a new mode
with every crtc at (0,0) and then pan to the right multi-monitor
setup. And since some hacks of mine added more calls to mode_set using
the stored crtc->x/y my multi-screen setup blew up.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise things migt not work too well.
Breakage introduced in
commit eb1cbe4848
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Mar 28 23:12:16 2012 +0200
drm/i915: split PLL update code out of i9xx_crtc_mode_set
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@vger.kernel.org (for 3.5 only)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This has been added in
commit de9a35abb3
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jun 5 11:03:40 2012 +0200
drm/i915: assert that the IBX port transcoder select w/a is implemented
Unfortunately I've failed to notice that these checks are not just
called for the port that is about to be disabled, but for all (which
makes sense for an assert ...), and the WARN missfired when disabling
another pipe than the one with the dp port.
Hence also check whether the port is actually disabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=54688
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As a quick reference I'll detail the motivation and design of the new code a
bit here (mostly stitched together from patchbomb announcements and commits
introducing the new concepts).
The crtc helper code has the fundamental assumption that encoders and crtcs can
be enabled/disabled in any order, as long as we take care of depencies (which
means that enabled encoders need an enabled crtc to feed them data,
essentially).
Our hw works differently. We already have tons of ugly cases where crtc code
enables encoder hw (or encoder->mode_set enables stuff that should only be
enabled in enocder->commit) to work around these issues. But on the disable
side we can't pull off similar tricks - there we actually need to rework the
modeset sequence that controls all this. And this is also the real motivation
why I've finally undertaken this rewrite: eDP on my shiny new Ivybridge
Ultrabook is broken, and it's broken due to the wrong disable sequence ...
The new code introduces a few interfaces and concepts:
- Add new encoder->enable/disable functions which are directly called from the
crtc->enable/disable function. This ensures that the encoder's can be
enabled/disabled at a very specific in the modeset sequence, controlled by our
platform specific code (instead of the crtc helper code calling them at a time
it deems convenient).
- Rework the dpms code - our code has mostly 1:1 connector:encoder mappings and
does support cloning on only a few encoders, so we can simplify things quite a
bit.
- Also only ever disable/enable the entire output pipeline. This ensures that
we obey the right sequence of enabling/disabling things, trying to be clever
here mostly just complicates the code and results in bugs. For cloneable
encoders this requires a bit of special handling to ensure that outputs can
still be disabled individually, but it simplifies the common case.
- Add infrastructure to read out the current hw state. No amount of careful
ordering will help us if we brick the hw on the initial modeset setup. Which
could happen if we just randomly disable things, oblivious to the state set up
by the bios. Hence we need to be able to read that out. As a benefit, we grow a
few generic functions useful to cross-check our modeset code with actual hw
state.
With all this in place, we can copy&paste the crtc helper code into the
drm/i915 driver and start to rework it:
- As detailed above, the new code only disables/enables an entire output pipe.
As a preparation for global mode-changes (e.g. reassigning shared resources) it
keeps track of which pipes need to be touched by a set of bitmasks.
- To ensure that we correctly disable the current display pipes, we need to
know the currently active connector/encoder/crtc linking. The old crtc helper
simply overwrote these links with the new setup, the new code stages the new
links in ->new_* pointers. Those get commited to the real linking pointers once
the old output configuration has been torn down, before the ->mode_set
callbacks are called.
- Finally the code adds tons of self-consistency checks by employing the new hw
state readout functions to cross-check the actual hw state with what the
datastructure think it should be. These checks are done both after every
modeset and after the hw state has been read out and sanitized at boot/resume
time. All these checks greatly helped in tracking down regressions and bugs in
the new code.
With this new basis, a lot of cleanups and improvements to the code are now
possible (besides the DP fixes that ultimately made me write this), but not yet
done:
- I think we should create struct intel_mode and use it as the adjusted mode
everywhere to store little pieces like needs_tvclock, pipe dithering values or
dp link parameters. That would still be a layering violation, but at least we
wouldn't need to recompute these kinds of things in intel_display.c. Especially
the port bpc computation needed for selecting the pipe bpc and dithering
settings in intel_display.c is rather gross.
- In a related rework we could implement ->mode_valid in terms of ->mode_fixup
in a generic way - I've hunted down too many bugs where ->mode_valid did the
right thing, but ->mode_fixup didn't. Or vice versa, resulting in funny bugs
for user-supplied modes.
- Ditch the idea to rework the hdp handling in the common crtc helper code and
just move things to i915.ko. Which would rid us of the ->detect crtc helper
dependencies.
- LVDS wire pair and pll enabling is all done in the crtc->mode_set function
currently. We should be able to move this to the crtc_enable callbacks (or in
the case of the LVDS wire pair enabling, into some encoder callback).
Last, but not least, this new code should also help in enabling a few neat
features: The hw state readout code prepares (but there are still big pieces
missing) for fastboot, i.e. avoiding the inital modeset at boot-up and just
taking over the configuration left behind by the bios. We also should be able
to extend the configuration checks in the beginning of the modeset sequence and
make better decisions about shared resources (which is the entire point behind
the atomic/global modeset ioctl).
Tested-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Damien Lespiau <damien.lespiau@intel.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Acked-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Acked-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we have solid modeset state tracking and checking code in
place, we can do the Full Monty also after dpms calls.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... let's see whether this catches anything earlier and I can track
down a few bugs.
v2: Add more checks and also add DRM_DEBUG_KMS output so that it's
clear which connector/encoder/crtc is being checked atm. Which proved
rather useful for debugging ...
v3: Add a WARN in the common encoder dpms function, now that also
modeset changes properly update the dpms state ...
v4: Properly add a short explanation for each WARN, to avoid the need
to correlate dmesg lines with source lines accurately. Suggested by
Chris Wilson.
v5: Also dump (expected, found) for state checks (or wherever it's not
apparent from the test what exactly mismatches with expectations).
Again suggested by Chris Wilson.
v6: Due to an issue reported by Paulo Zanoni I've noticed that the
encoder checking is by far not as strict as it could and should be.
Improve this.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this to avoid confusing the hw state readout code with the cpt
pch plls at resume time: We'd read the new pipe state (which is
disabled), but still believe that we have a life pll connected to that
pipe (from before the suspend). Hence properly disable pipes to clear
out all the residual state.
This has the neat side-effect that we don't enable ports prematurely
by restoring bogus state from the saved register values.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this change we can (finally!) rip out a few of the temporary hacks
and clean up a few other things:
- Kill intel_crtc_prepare_encoders, now unused.
- Kill the hacks in the crtc_disable/enable functions to always call the
encoder callbacks, we now always call the crtc functions with the right
encoder -> crtc links.
- Also push down the crtc->enable, encoder and connector dpms state
updates. Unfortunately we can't add a WARN in the crtc_disable
callbacks to ensure that the crtc is always still enabled when
disabling an output pipe - the crtc sanitizer of the hw readout path
can hit this when it needs to disable an active pipe without any
enabled outputs.
- Only call crtc->disable if the pipe is already enabled - again avoids
running afoul of the new WARN.
v2: Copy&paste our own version of crtc_in_use, too.
v3: We need to update the dpms an encoder->connectors_active states,
too.
v4: I've forgotten to kill the unconditional encoder->disable calls in
the crtc_disable functions.
v5: Rip out leftover debug printk.
v6: Properly clear intel_encoder->connectors_active. This wasn't
properly cleared when disabling an encoder because it was no longer on
the new connector list, but the crtc was still enabled (i.e. switching
the encoder of an active crtc). Reported by Jani Nikula.
v7: Don't clobber the encoder->connectors_active state of untouched
encoders. Since X likes to first disable all outputs with dpms off
before setting a new framebuffer, this hit a few warnings. Reported by
Paulo Zanoni.
v8: Kill the now stale comment warning that intel_crtc->active is not
always updated at the right times.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that set_mode also disables crtcs and expects it's new
configuration in the staged output links we need to adjust the load
detect code a bit.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This seems to be the symptom of a few neat bugs, hence be more
obnoxious when this fails.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because that's what it is. Unfortunately we can't rip this out because
the fb helper has an incetious relationship with the crtc helper - it
likes to call disable_unused_functions, among other things.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This requires a few changes
- We still need a noop function for crtc->disable, becuase the fb
helper is a bit too intimate with the crtc helper.
- We need to clear crtc->fb ourselves in intel_crtc_disable now that
we no longer rely on the helper's disable_unused_functions to do
that.
- We need to split out the sare update code, becuase the crtc code
can't call update_dpms any more, it needs to disable the crtc
unconditionally. This is because we now keep onto the encoder ->
crtc mapping of the (still) active output pipe configuration.
- To check that we really disable a crtc that still has encoders,
insert a WARN_ON(!enabled) in the crtc disable function.
- Lastly, we need to walk over all crtcs to update their enabled state
after having called commit_output_state - for all disabled crtcs the
crtc helper code has done that for us previously.
v2: Update connector dpms and encoder->connectors_active after
disabling the crtc, too.
v3: Noop-out intel_encoder_disable. Similarly to the crtc disable
callback used by the crtc helper code we can't simply remove all these
encoder callbacks: The fb helper (which we still use) has a rather
incetious relationship with the crtc helper code ...
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... using the pipe masks from the previous patch.
Well, not quite:
- We still need to call the disable_unused_functions helper, until
we've moved the call to commit_output_state further down and
adjusted intel_crtc_disable a bit. The next patch will do that.
- Because we don't support (yet) mode changes on more than one crtc at
a time, some of the modeset_pipes checks are a bit hackish - but
that only needs fixing once we incorporate global modeset support.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is definetely a bit more generic than currently required, but if
we keep track of all crtcs that need to be disabled/enable (because
they loose an encoder or something similar), crtcs that get completely
disabled and those that we need to do an actual mode change nicely
prepares us for global modeset operations on multiple crtcs.
The only big thing missing here would be a global resource allocation
step (for e.g. pch plls), which would equally frob these bitmasks if
e.g. a crtc only needs a new pll. Or if we need to enable dithering on
an another pipe due to bandwidth constrains somewhere.
These masks aren't yet put to use in this patch, this will follow in the
next one.
v2-v5: Fix up the computations for good (hopefully).
v6: Fixup a confusion reported by Damien Lespiau: I've conserved the
(imo braindead) behaviour of the crtc helper to disable _any_
disconnected outputs if we do a modeset, even when that newly disabled
connector isn't connected to the crtc being changed by the modeset.
The effect of that is that we could disable an arbitrary number of
unrelated crtcs, which I haven't taken into account when writing this
code. Fix this up.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The "is this encoder cloned" check will be reused by the lvds encoder,
hence exract it.
v2: Be a bit more careful about that we need to check the new, staged
ouput configuration in the check_non_cloned helper ...
v3: Kill the double negation with s/!non_cloned/is_cloned/, suggested
by Jesse Barnes.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While at it, adjust a few things:
- Only assigng the new mode to crtc->mode right before calling the
mode_set callbacks - none of the previous callbacks depend upon
this, they all use the mode argument (as they should).
- Check encoder->new_crtc instead of the current crtc to check whether
the encoder will be used. This prepares for moving the staged output
committing further down in the sequence. Follow-on patches will fix
up individual ->mode_fixup callbacks (only tv and lvds are affected
though).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's rather pointless to compute crtc->enabled twice right away ;-)
The only thing we really have to be careful about is that we frob the
dpms state only after a successful modeset and when we've actually
haven't just disabled the crtc.
Hooray for convoluted interfaces ...
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Originally this has been introduced in
commit 6eebd6bb5f
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Nov 28 21:10:05 2011 +0000
drm: Fix lack of CRTC disable for drm_crtc_helper_set_config(.fb=NULL)
With the improvements of the output state staging and no longer
overwriting crtc->fb before the hw state is updated we can now handle
crtc disabling as part of the normal modeset sequence.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Passing in the old fb, having overwritten the current fb, leads to
some neatly convoluted code. It's much simpler if we defer the
crtc->fb update to the place that updates the hw, in pipe_set_base.
This way we also don't need to restore anything in case something
fails - we only update crtc->fb once things have succeeded.
The real reason for this change is that now we keep the old fb
assigned to crtc->fb, which allows us to finally move the crtc disable
case into the common low-level set_mode function in the next patch.
Also don't clobber crtc->x and crtc->y, we neatly pass these down the
callchain already. Unfortunately we can't do the same with crtc->mode,
because that one is being used in the mode_set callbacks.
v2: Don't restore the drm_crtc object any more on failed modesets,
since we've lose an fb reference otherwise. Also (and this is the
reason this has been found), this totally confused the modeset state
tracking, since it clobbers crtc->enabled. Issue reported by Paulo
Zanoni.
v3: Rip out the entire crtc saving into struct intel_set_config, not
just the restoring part.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is the core of the new modeset logic.
The current code which is based upon the crtc helper code first
updates all the link of the new display pipeline and then calls the
lower-level set_mode function to execute the required callbacks to get
there. The issue with this approach is that for disabling we need to
know the _current_ display pipe state, not the new one.
Hence we need to stage the new state of the display pipe and only
update it once we have disabled the current configuration and before we
start to update the hw registers with the new configuration.
This patch here just prepares the ground by switching the new output
state computation to these staging pointers. To make it clearer,
rename the old update_output_state function to stage_output_state.
A few peculiarities:
- We're also calling the set_mode function at various places to update
properties. Hence after a successfule modeset we need to stage the
current configuration (for otherwise we might fall back again). This
happens automatically because as part of the (successful) modeset we
need to copy the staged state to the real one. But for the hw
readout code we need to make sure that this happens, too.
- Teach the new staged output state computation code the required
smarts to handle the disabling of outputs. The current code handles
this in a special case, but to better handle global modeset changes
covering more than one crtc, we want to do this all in the same
low-level modeset code.
- The actual modeset code is still a bit ugly and wants to know the new
crtc->enabled state a bit early. Follow-on patches will clean that
up, for now we have to apply the staged output configuration early,
outside of the set_mode functions.
- Improve/add comments in stage_output_state.
Essentially all that is left to do now is move the disabling code into
set_mode and then move the staged state update code also into
set_mode, at the right place between disabling things and calling the
mode_set callbacks for the new configuration.
v2: Disabling a crtc works by passing in a NULL mode or fb, userspace
doesn't hand in the list of connectors. We therefore need to detect
this case manually and tear down all the output links.
v3: Properly update the output staging pointers after having read out
the hw state.
v4: Simplify the code, add more DRM_DEBUG_KMS output and check a few
assumptions with WARN_ON. Essentially all things that I've noticed
while debugging issues in other places of the code.
v4: Correctly disable the old set of connectors when enabling an
already enabled crtc on a new set of crtc. Reported by Paulo Zanoni.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We actually only touch the connector -> encoder and encoder -> crtc
linking. So it's enough to just save/restore that.
While at it, also switch to kcalloc to allocate these arrays (omission
in the commit message spotted by Jesse Barnes).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because they all are, the ioctl command never calls us with any of
these violated. Also drop a equally pointless empty debug message (and
also in set_cursor, while we're at it).
With all these changes, intel_crtc_set_config is neatly condensed down
to it's essence, the actual modeset code (or fb update calling code)
v2: The fb helper code is actually stretching ->set_config semantics a bit,
it calls it with set->mode == NULL but set->fb != NULL.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we'll set_fb complains pretty loudly if we the crtc is off
and userspace moves the NULL fb around a bit. Yeah, this actually
happens in the wild ...
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Yikes!
But yeah, we have to do this until someone volunteers to clean up the
fb helper and rid it of its incetious relationship with the crtc
helper code.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Note that this function already clobbers the mode config state,
so we have to clean things up if something fails.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This computes what exactly changed in the modeset configuration, i.e.
whether a full modeset is required or only an update of the
framebuffer base address or no change at all.
In the future we might add more checks for e.g. when only the output
mode changed, so that we could do a minimal modeset for outputs that
support this. Like the lvds/eDP panels where we only need to update
the panel fitter.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the end this won't be of much use to us, but meanwhile just extract
it to get a better overview of what exactly set_config does.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_crtc_set_config is an unwidly beast and is in serious need of
some function extraction. To facilitate that, introduce a struct to
keep track of all the state involved. Atm it doesn't do much more than
keep track of all the allocated memory.
v2: Apply some bikeshed to intel_set_config_free, as suggested by
Jesse Barnes.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Many BIOSen forget to turn on the pipe A after resume (because they
actually don't turn on anything), so we have to do that ourselves when
sanitizing the hw state.
I've discovered this due to the recent addition of a pipe WARN that
takes the force quirk into account.
v2: Actually try to enable the pipe with a proper configuration instead
of simpyl switching it on with whatever random state the bios left it
in after resume.
v3: Fixup rebase conflict - the load_detect functions have lost their
encoder argument.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Afaict this has been used for two things:
- To prevent the crtc enable code from being run twice. We have now
intel_crtc->active to track this in a more precise way.
- To ensure the code copes correctly with the unknown hw state after
boot and resume. Thanks to the hw state readout and sanitize code we
have now a better way to handle this.
The only thing it still does is complicate our modeset state space.
Having outlived its usefullness, let it just die.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we can only check the connector state after a dpms call - while
doing modeset with the copy&pasted crtc helper code things are too
ill-defined for proper checking. But the idea is very much to call
this check from the modeset code, too.
v2: Fix dpms check and don't presume that if the hw isn't on that it
must not be linked up with an encoder (it could simply be switched off
with the dpms state).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of resetting a few things and hoping that this will work
out.
To properly disable the output pipelines at the initial modeset after
resume or boot up we need to have an accurate picture of which outputs
are enabled and connected to which crtcs. Otherwise we risk disabling
things at the wrong time, which can lead to hangs (or at least royally
confused panels), both requiring a walk to the reset button to fix.
Hence read out the hw state with the freshly introduce get_hw_state
functions and then sanitize it afterwards.
For a full modeset readout (which would allow us to avoid the initial
modeset at boot up) a few things are still missing:
- Reading out the mode from the pipe, especially the dotclock
computation is quite some fun.
- Reading out the parameters for the stolen memory framebuffer and
wrapping it up.
- Reading out the pch pll connections - luckily the disable code
simply bails out if the crtc doesn't have a pch pll attached (even
for configurations that would need one).
This patch here turned up tons of smelly stuff around resume: We
restore tons of register in seemingly random way (well, not quite, but
we're not too careful either), which leaves the hw in a rather
ill-defined state: E.g. the port registers are sometimes
unconditionally restore (lvds, crt), leaving us with an active
encoder/connector but no active pipe connected to it. Luckily the hw
state sanitizer detects this madness and fixes things up a bit.
v2: When checking whether an encoder with active connectors has a crtc
wire up to it, check for both the crtc _and_ it's active state.
v3:
- Extract intel_sanitize_encoder.
- Manually disable active encoders without an active pipe.
v4: Correclty fix up the pipe<->plane mapping on machines where we
switch pipes/planes. Noticed by Chris Wilson, who also provided the
fixup.
v5: Spelling fix in a comment, noticed by Paulo Zanoni
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is all glorious if we try really hard to only enable/disable an
entire display pipe to ensure that everyting happens in the right
order. But if we don't know the output configuration when the driver
takes over, this will all be for vain because we'll make the hw angry
right on the first modeset - we don't know what outputs/ports are
enabled and hence have to disable everything in a rather ad-hoc way.
Hence we need to be able to read out the current hw state, so that we
can properly tear down the current hw state on the first modeset.
Obviously this is also a nice preparation for the fastboot work, where
we try to avoid the modeset on driver load if it matches what the hw
is currently using.
Furthermore we'll be using these functions to cross-check the actual
hw state with what we think it should be, to ensure that the modeset
state machine actually works as advertised.
This patch only contains the interface definitions and a little helper
for the simple case where we have a 1:1 encoder to connector mapping.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is the first tiny step towards cross-checking the entire modeset
state machine with WARNs. A crtc can only be enabled when it's
actually in use, i.e. crtc->active imlies crtc->enabled.
Unfortunately we can't (yet) check this when disabling the crtc,
because the crtc helpers are a bit slopy with updating state and
unconditionally update crtc->enabled before changing the hw state.
Fixing that requires quite some more work.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of going through the crtc helper function tables.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the new infrastructure we're doing this when enabling/disabling
the entire display pipe.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- We don't have the ->get_crtc callback.
- Call intel_encoder->disable directly.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Together with the static helper functions drm_crtc_prepare_encoders
and drm_encoder_disable (which will be simplified in the next patch,
but for now are 1:1 copies). Again, no changes beside new names for
these functions.
Also call our new set_mode instead of the crtc helper one now in all
the places we've done so far.
v2: Call the function just intel_set_mode to better differentia it
from intel_crtc_mode_set which really only does the ->mode_set step of
the entire modeset sequence on one crtc. Whereas this function does
the global change.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also kill the error-path, we have a fixed connector->encoder mapping.
Unfortunately we can't rip out all the ->best_encoder callbacks, these
are all still used by the fb_helper. Neat helper layering violation there.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And the following static functions required by it:
drm_encoder_crtc_ok, drm_crtc_helper_disable
No changes safe for the s/drm/intel prefix change.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We no longer need them. And now that all encoders are converted, we
can finally move the cpt modeset check to the right place - at the end
of the crtc_enable function.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All encoders are now converted so there's no need for these checks any
more.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Yeah, big patch but I couldn't come up with a neat idea of how to
split it up further, that wouldn't break dpms on cloned configs
somehow. But the changes in dvo/sdvo/crt are all pretty much
orthonogal, so it's not too bad a patch.
These are the only encoders that support cloning, which requires a few
special changes compared to the previous patches.
- Compute the desired state of the display pipe by walking all
connected encoders and checking whether any has active connectors.
To make this clearer, drop the old mode parameter to the crtc dpms
function and rename it to intel_crtc_update_dpms.
- There's the curious case of intel_crtc->dpms_mode. With the previous
patches to remove the overlay pipe A code and to rework the load
detect pipe code, the big users are gone. We still keep it to avoid
enabling the pipe twice, but we duplicate this logic with
crtc->active, too. Still, leave this for now and just push a fake
dpms mode into it that reflects the state of the display pipe.
Changes in the encoder dpms functions:
- We clamp the dpms state to the supported range right away. This is
escpecially important for the VGA outputs, where only older hw
supports the intermediate states. This (and the crt->adpa_reg patch)
allows us to unify the crt dpms code again between all variants
(gmch, vlv and pch).
- We only enable/disable the output for dvo/sdvo and leave the encoder
running. The encoder will be disabled/enabled when we switch the
state of the entire output pipeline (which will happen right away
for non-cloned setups). This way the duplication is reduced and
strange interaction when disabling output ports at the wrong time
avoided.
The dpms code for all three types of connectors contains a bit of
duplicated logic, but I think keeping these special cases separate is
simpler: CRT is the only one that hanldes intermediate dpms state
(which requires extra logic to enable/disable things in the right
order), and introducing some abstraction just to share the code
between dvo and sdvo smells like overkill. We can do that once someone
bothers to implement cloning for the more modern outputs. But I doubt
that this will ever happen.
v2: s/crtc/crt/_set_dpms, noticed by Paulo Zanoni.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've picked hdmi as the first encoder to convert because it's rather
simple:
- no cloning possible
- no differences between prepare/commit and dpms off/on switching.
A few changes are required to do so:
- Split up the dpms code into an enable/disable function and wire it
up with the intel encoder.
- Noop out the existing encoder prepare/commit functions used by the
crtc helper - our crtc enable/disable code now calls back into the
encoder enable/disable code at the right spot.
- Create new helper functions to handle dpms changes.
- Add intel_encoder->connectors_active to better track dpms state. Atm
this is unused, but it will be useful to correctly disable the
entire display pipe for cloned configurations. Also note that for
now this is only useful in the dpms code - thanks to the crtc
helper's dpms confusion across a modeset operation we can't (yet)
rely on this having a sensible value in all circumstances.
- Rip out the encoder helper dpms callback, if this is still getting
called somewhere we have a bug. The slight issue with that is that
the crtc helper abuses dpms off to disable unused functions. Hence
we also need to implement a default encoder disable function to do
just that with the new encoder->disable callback.
- Note that we drop the cpt modeset verification in the commit
callback, too. The right place to do this would be in the crtc's
enable function, _after_ all the encoders are set up. But because
not all encoders are converted yet, we can't do that. Hence disable
this check temporarily as a minor concession to bisectability.
v2: Squash the dpms mode to only the supported values -
connector->dpms is for internal tracking only, we can hence avoid
needless state-changes a bit whithout causing harm.
v3: Apply bikeshed to disable|enable_ddi, suggested by Paulo Zanoni.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just prep work, not yet put to some use.
Note that because we're still using the crtc helper to switch modes
(and their complicated way to do partial modesets), we need to call
the encoder's disable function unconditionally.
But once this is cleaned up we shouldn't call the encoder's disable
function unconditionally any more, because then we know that we'll
only call it if the encoder is actually enabled. Also note that we
then need to be careful about which crtc we're filtering the encoder
list on: We want to filter on the crtc of the _current_ mode, not the
one we're about to set up.
For the enabling side we need to do the same trick. And again, we
should be able to simplify this quite a bit when things have settled
into place.
Also note that this simply does not take cloning into account, so dpms
needs to be handled specially for the few outputs where we even bother
with it.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just impendance matching with the the crtc helper stuff.
... and somehow the design of this all ended up in this commit here,
too ;-)
The big plan is that this new set of crtc display_funcs take full
responsibility of modeset operations for the entire display output
pipeline (by calling down into object-specific callbacks and
functions). The platform-specific callbacks simply know best what the
proper order is.
This has the drawback that we can't do minimal change-overs any more
if a modeset just disables one encoder in a cloned configuration
(because we will only expose a disable/enable action that takes
down/sets up the entire crtc including all encoders). Imo that's the
only sane way to do it though:
- The use-case for this is pretty minimal, even when presenting (at
least sane people) should use a dual-screen output so that you can
see your notes on your panel. Clone mode is imo BS.
- With all the clone mode constrains, shared resources, and special
ordering requirements (which differ even on the same platform
sometimes for different outputs) there's no way we'd get this right
for all cases. Especially since this is a under-used feature.
- And to top it off: On haswell even dp link re-training requires us
to take down the entire display pipe - otherwise the chip dies.
So the only sane way is to do a full modeset on every crtc where the
output config changes in any way.
To support global modeset (i.e. set the configuration for all crtcs at
once) we'd then add one more function to allocate global and shared
objects in the best ways (e.g. fdi links, pch plls, ...). The crtc
functions would then simply use the pre-allocated stuff (and shouldn't
be able to fail, ever). We could even do all the object pinning in
there (and maybe try to defragment the global gtt if we fail)!
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because that's what we're essentially calling. This is the first step
in untangling the crtc_helper induced dpms handling mess we have - at
the crtc level we only have 2 states and the magic is just in
selecting which one (and atm there isn't even much magic, but on
recent platforms where not even the crt output has more than 2 states
we could do better).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wrong order of parameters passed-in when calling hdmi/adpa
/lvds_pipe_enabled(), 2nd and 3rd parameters are reversed.
This bug was indroduced by
commit 1519b9956e
Author: Keith Packard <keithp@keithp.com>
Date: Sat Aug 6 10:35:34 2011 -0700
drm/i915: Fix PCH port pipe select in CPT disable paths
The reachable tag for this commit is v3.1-rc1-3-g1519b99
Signed-off-by: Anhua Xu <anhua.xu@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44876
Tested-by: Daniel Schroeder <sec@dschroeder.info>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This addresses WaPruneModeWithIncorrectHsyncOffset.
Bugzilla: http://bugs.freedesktop.org/show_bug.cgi?id=50236
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added new haswell_write_eld() to initialize Haswell HDMI audio registers
to generate an unsolicited response to the audio controller driver to
indicate that the controller sequence should start.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
New-ish devices have 3 pipes, so let's not just hardcode 2 but use the
for_each_pipe() macro and make struct intel_display_error_state is big
enough.
V2: Also add the number of pipes emitted (Chris Wilson)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use _PIPE macro to get correct register definition for IBX/CPT, discard
old variable "i" way.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Added the DIP_PORT_SEL #define from a preceeding patch in the
series that needs more work.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simply to make the ilk+ crtc disable path clearer and more symmetric
with the enable function.
Also switch to intel_crtc for the enable function.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since it's redundant - we can get the attached encoder in the
functions themselves.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A few things need adjustement:
- Change the dpms state by calling the dpms connector function and
not some crtc helper internal callbacks. Otherwise this will break
once we switch to our own dpms handling.
- Instead of tracking and restoring intel_crtc->dpms_mode use the
connector's dpms variable - the former relies on the dpms compuation
rules used by the crtc helper. And it would break when the encoder
is cloned and the other output has a different dpms state. But luckily
no one is crazy enough for that.
- Properly clear the connector -> encoder -> crtc linking, even when
failing (note that the crtc helper removes the encoder -> crtc link
in disabled_unused_functions for us).
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the pipe A quirk properly fixed up for i830M, this shouldn't be
required any longer.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For some odd reason we've missed i830 and a i855 variant. Also
kill the two now redundant i830 entries.
v2: Don't add the missing 855 id to the pipe A quirk list, we seem to
lack justification for it.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wrong order of parameters passed-in when calling hdmi/adpa
/lvds_pipe_enabled(), 2nd and 3rd parameters are reversed.
This bug was indroduced by
commit 1519b9956e
Author: Keith Packard <keithp@keithp.com>
Date: Sat Aug 6 10:35:34 2011 -0700
drm/i915: Fix PCH port pipe select in CPT disable paths
The reachable tag for this commit is v3.1-rc1-3-g1519b99
Signed-off-by: Anhua Xu <anhua.xu@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQLWtvAAoJEHm+PkMAQRiG/DYH+wd0FqfEuYkYk4KPyAPuhKpX
zX7HYfLvyJE/ZYIdrhjq1E6Xm2KNr7gtX7/Rdzi2W38M9sjbYzwG1UGIw51qnxWy
yZJH9BGkfyQgQPeuDGohfB6DkDy2JWr2eqMDvakjOwgBsIzji0PQD/f3UvndhtUa
c+tTj/kjavHE1Yr2Wy6OnRZz3Uc0hIMn/Q0JqtbCs3LUgEV1KA4OEAe56XNz4Ku4
WE+FFaGFPvtriQsQON+ohPS5IC8jzQGK/0vbrJ4lWjFnZy4gvZXnborTOwD0WSQG
fbsNuxp1AaM2/pqfMwXm1w0ADvwOITHNiwwXf9id6DoK81QwTFpUdvKpn6yB6gQ=
=rurr
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc2' into drm-intel-next
Backmerge Linux 3.6-rc2 to resolve a few funny conflicts before we put
even more madness on top:
- drivers/gpu/drm/i915/i915_irq.c: Just a spurious WARN removed in
-fixes, that has been changed in a variable-rename in -next, too.
- drivers/gpu/drm/i915/intel_ringbuffer.c: -next remove scratch_addr
(since all their users have been extracted in another fucntion),
-fixes added another user for a hw workaroudn.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This has originally been introduced to not oversubscribe the dp links
in
commit 885a5fb5b1
Author: Zhenyu Wang <zhenyuw@linux.intel.com>
Date: Tue Jan 12 05:38:31 2010 +0800
drm/i915: fix pixel color depth setting on eDP
Since then we've fixed up the dp link bandwidth calculation code and
should now automatically fall back to 6bpc dithering. So this is
unnecessary.
Furthermore it seems to break the new MacbookPro with retina display,
hence let's just rip this out.
Reported-by: Benoit Gschwind <gschwind@gnu-log.net>
Cc: Benoit Gschwind <gschwind@gnu-log.net>
Cc: Francois Rigaut <frigaut@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Tested-by: Benoit Gschwind <gschwind@gnu-log.net>
Tested-by: Bernhard Froemel <froemel at vmars tuwien.ac.at>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
--
Testing feedback highgly welcome, and thanks for Benoit for finding
out that the bpc computations are busted.
-Daniel
- intel_encoder->type is INTEL_OUTPUT_SOMETHING
- drm_encoder->encoder_type is DRM_MODE_ENCODER_SOMETHING
Here we're using intel_encoder, so compare the oranges against
oranges. While at it, rename the variable to "intel_encoder" so we
keep our naming standards used everywhere.
Luckily this was not a bug because both DRM_MODE_ENCODER_DAC and
INTEL_OUTPUT_ANALOG are defined as 1. This is the only case where the
drm definition matches the intel definition.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way it's easier so see what belongs together, and what is used
by the ilk ips code. Also add some comments that explain the locking.
Note that (cur|min|max)_delay need to be duplicated, because
they're also used by the ips code.
v2: Missed one place that the dev_priv->ips change caught ...
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
"- Regression fixer for an OOPS at boot when i915.ko is built-in and
CONFIG_PM=n, introduce in 3.5 (patch from Hunt Xu)
- Regression fixer for occlusion query failures, the required w/a wasn't
applied in all cases (thanks to Eric for tracking this on down).
- dmar vs. dma_buf imprt fix (Dave Airlie)
- 2 patches to fight down forcewake issues on snb. This is the stuff I've
talked about 2 weeks ago already, it's a minefield. Investigation still
going on, but afaict this is the best we have for now.
- a few minor things to keep coverty&compiler happy (Alan, Davendra,
Stéphane)
- tons of hsw pci ids - this one is a bit late because internal approval
sometimes takes a while, but ppl in charge finally agreed that world+dog
already knows about ult and crw haswell variants ;-)
Wrt regressions I'm aware of:
- the power regression due to semaphores=1. Ben is running around with a
killawatt, unfortunately we have a hard time reproducing this one. And
this /shouldn't/ increase power usage. Ben has turned up a few odds bits
though already.
- the lvds fix in 3.6-rc1 broke a backlight after lid close/open (but can
be resurrected with a modeset cycle). I guess we anger the bios - I'm
still looking into this one.
- gmbus broke edid reading on an odd-ball monitor, we need to fall-back.
Due to vacation (both mine&the reporter's) this is stalling for a final
patch and a tested-by on it. But issue is fully diagnosed."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: correctly order the ring init sequence
drm/i915: add more Haswell PCI IDs
drm/i915: make rc6 in sysfs functions conditional
drm/i915: Workaround hang with BSD and forcewake on SandyBridge
drm/i915: Make intel_panel_get_backlight static.
i915: don't map imported dma-bufs for dmar.
drm/i915: remove unused variable
drm/i915: Don't forget to apply SNB PIPE_CONTROL GTT workaround.
drm/i915: fix forcewake related hangs on snb
i915: Remove silly test
i915: fix error path leak in intel_sdvo_write_cmd
vlv: it might be wise if we initialised the flag value...
We should not hit this under any sane conditions, but still, this does not
looks right.
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: stable@vger.kernel.org
Reported-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Reviewed-by: Chris Wlison <chris@chris-wilson.co.uk>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We believe to have squashed all issues around the gen6+ rps interrupt
generation and why the gpu sometimes got stuck. With that cleared up,
there's no user left for the sanitize_pm infrastructure, so let's just
rip it out.
Note that 'intel_reg_write 0xa014 0x13070000' is the w/a if we find
ourselves stuck again.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise our initial behaviour is "randomly save a bogus PLL
choice" as far as I can see.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes: (this pull is the one with the bad patch dropped)
First pile of fixes for 3.6 already, and I'm afraid it's a bit larger than
what I'd wish for. But I've moved all the feature-y stuff to -next, so
this really is all -fixes. Most of it is handling fallout from the hw
context stuff, discovered now that mesa git has started using them for
real. Otherwise all just small fixes:
- unbreak modeset=0 on gen6+ (regressed in next)
- const mismatch fix for ->mode_fixup
- simplify overly clever lvds modeset code (current code can totally
confuse backlights, resulting in broken panels until a full power draw
restores them).
- fix some fallout from the flushing_list disabling (regression only
introduced in -next)
- DP link train improvements (this also kills the last 3.2 dp regression
afaik)
- bugfix for the new ddc VGA detection on newer platforms
- minor backlight fixes (one of them a -next regression)
- only enable the required PM interrupts (to avoid waking up the cpu
unnecessarily)
- some really minor bits (workaround clarification, make coverty happy,
hsw init fix)
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel: (23 commits)
drm/i915: unbreak lastclose for failed driver init
drm/i915: Set the context before setting up regs for the context.
drm/i915: constify mode in crtc_mode_fixup
drm/i915/lvds: ditch ->prepare special case
drm/i915: dereferencing an error pointer
drm/i915: fix invalid reference handling of the default ctx obj
drm/i915: Add -EIO to the list of known errors for __wait_seqno
drm/i915: Flush the context object from the CPU caches upon switching
drm/i915: Make the lock for pageflips interruptible
drm/i915: don't forget the PCH backlight registers
drm/i915: Insert a flush between batches if the breadcrumb was dropped
drm/i915: missing error case in init status page
drm/i915: mask tiled bit when updating ILK sprites
drm/i915: try to train DP even harder
drm/i915: kill intel_ddc_probe
drm/i915: check whether we actually received an edid in detect_ddc
drm/i915: fix up PCH backlight #define mixup
drm/i915: Add comments to explain the BSD tail write workaround
drm/i915: Disable the BLT on pre-production SNB hardware
drm/i915: initialize power wells in modeset_init_hw
...
As suggested by Daniel, rip out the independent timers for device and
crtc busyness and integrate the manual powermanagement of the display
engine into the GEM core and its request tracking. The benefits are that
the code is a lot smaller, fewer moving parts and should fit more neatly
into the overall activity tracking of the driver.
v2: Complete overhaul and removal of the racy timers and workers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds support for the ns2501 DVO, found in some older Fujitsu/Siemens Labtops.
It is in the state of "works for me".
Includes now proper DPMS support. Includes switching between resolutions -
from 640x480 to 1024x768.
Currently assumes that the native display resolution is 1024x768.
The ns2501 seems to be rather critical - if the output PLL is not
running, the chip doesn't seem to be clocked and then doesn't react
on i2c messages. Thus, a quick'n-dirty trick ensures that the DVO
is active before submitting any i2c messages to it. This is
probably to be reviewed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17902
Signed-off-by: Thomas Richter <thor@math.tu-berlin.de>
[danvet: fixup whitespace fail.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed for Haswell, but already has its uses here.
This patch started as a small patch written patch by Shobhit Kumar,
but it has changed so much that none of its original lines remain.
Credits-to: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of having a giant if cascade to figure this out according to
the passed-in register. We could do quite a bit more cleaning up and
all by using the port at more places, but I think this should be part
of a bigger rework to introduce a struct intel_digital_port which
would keep track of all these things. I guess this will be part of
some haswell-DP-induced refactoring.
For now this rips out the big cascade, which is what annoyed me so
much.
v2: Add port variable name back for the func decl (I've tried to trick
myself below the 80 char limit).
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Intel hw only has one MUX for encoders, so outputs are either not
cloneable or all in the same group of cloneable outputs. This neatly
simplifies the code and allows us to ditch some ugly if cascades in
the dp and hdmi init code (well, we need these if cascades for other
stuff still, but that can be taken care of in follow-up patches).
Note that this changes two things:
- dvo can now be cloned with sdvo, but dvo is gen2 whereas sdvo is
gen3+, so no problem. Note that the old code had a bug and didn't
allow cloning crt with dvo (but only the other way round).
- sdvo-lvds can now be cloned with sdvo-non-tv. Spec says this won't
work, but the only reason I've found is that you can't use the
panel-fitter (used for lvds upscaling) with anything else. But we
don't use the panel fitter for sdvo-lvds. Imo this part of Bspec is
a) rather confusing b) mostly as a guideline to implementors (i.e.
explicitly stating what is already implicit from the spec, without
always going into the details of why). So I think we can ignore this
- worst case we'll get a bug report from a user with with sdvo-lvds
and sdvo-tmds and have to add that special case back in.
Because sdvo lvds is a bit special explain in comments why sdvo LVDS
outputs can be cloned, but native LVDS and eDP can't be cloned - we
use the panel fitter for the later, but not for sdvo.
Note that this also uncoditionally initializes the panel_vdd work used
by eDP. Trying to be clever doesn't buy us anything (but strange bugs)
and this way we can kill the is_edp check.
v2: Incorporate review from Paulo
- Add in a missing space.
- Pimp comment message to address his concerns.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we take the struct_mutex lock to access the command-stream, there is
a possibility that we may need to wait for a GPU hang and so should make
the lock both interruptible and error-checking.
References: https://bugs.freedesktop.org/show_bug.cgi?id=50069
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This initializes power wells within the modeset_init_hw routine.
Testing has shown that this works for both driver load time and for
suspend-resume code paths.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQAfWKAAoJEHm+PkMAQRiG/DwIAIullMhkDhD/GJcn24ZbUJoa
v6zRPK2hIavuKH/6bUoUiXT346PUYgVnRMhetuYKJFURz6KX/nmlxve/iXNn/WP1
9hnxhE+zcnp2qKI83c3Yok09eed1KnGY5hWQkqXM2gzji/OU0pCKchOcL01l//uz
iiWpNAXEVUnT92CafnHlZ55f/MWVqRFmDKi3Ty1YKSskhojQ6NOPsWCxrTxKVbim
2YPXc3D+xLHzF12ufVgla20AF4KnK8m+tFugniRAqArIagpzBUP1x1wk0RN5PyBD
FTP8lv7bSfBusp41/mPDB66WAe9EfQBoWQY6jloJjp0i8xnMyH5V05pImBV5NwU=
=O+gl
-----END PGP SIGNATURE-----
Merge tag 'v3.5-rc7' into drm-next
Merge Linus tree into drm to fixup conflicts in radeon code for further
testing before upstream merge.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/radeon/radeon_gart.c
We already have this pattern at quite a few places, and moving part of
the modeset helper stuff into the driver will add more.
v2: Don't clobber the crtc struct name with the macro parameter ...
v3: Convert two more places noticed by Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The tileoffset register only supports a limited offset in x/y of 4096,
so for giant screen configuration with a shared fb we wrap around.
Fix this by computing a linear offset in tiles (pages) and only use
the tileoffset register to offset within the tile.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To avoid recomputing the display framebuffer offset on gen2/3
pageflips. This is also prep work to do similar trickery on gen4+
Also:
- kill "Start", such upper-case remnants from the ddx must surely die.
- rename "Offset" to linear_offset, to make it clearer that on gen4+
this is only used by the hw for linear buffers, for tiled buffers it
uses the TILEOFF register.
- call DSAPADDR DSPLINOFF on gen4+ for the same reason (and because
the documentation really renamed the register).
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
MI display flips can't handle some changes in the framebuffer
format or layout. Return an error in such cases.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is necessary for the modesetting to work correctly after a
suspend-resume cycle. Without this, the pipes and clocks got the correct
configuration, but the underlying DDI buffers configuration was lost.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function is used to set the PCH_DREF_CONTROL register, which does
not exist on LPT anymore.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While creating the new enable/disable_gt_powersave functions in
commit 8090c6b9da
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jun 24 16:42:32 2012 +0200
drm/i915: wrap up gt powersave enabling functions
I've botched up the handling of ironlake_disable_rc6. Fix this up by
calling it at the right place. Note though that ironlake_disable_rc6
does a bit more than just disabling rc6 - it also tears down all the
allocated context objects.
Hence we need to move intel_teardown_rc6 out and directly call it from
intel_modeset_cleanup.
Also properly mark ironlake_enable_rc6 as static and kill the un-used
declaration in i915_drv.h.
Note: In review a question popped out why disable_rc6 also tears down
the backing object and why we should move that out - it's simply for
consistency with gen6+ rps code, which does it that way.
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tidy up the routines for interacting with the GT (in particular the
forcewake dance) which are scattered throughout the code in a single
structure.
v2: use wait_for_atomic for polling.
v3: *really* use wait_for_atomic for polling.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit f82cfb6bcd.
This breaks the backlight controls on my IVB asus zenbook with an eDP
panel.
I guess the right fix would be to read this bit and use either the pch
or the cpu register to frob the backlight values. But that is stuff
for -next.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The enable functions grabbed dev->struct_mutex themselves, whereas
the disable functions expected dev->struct_mutex to be held by the
caller. Move the locking out to the (currently only) callsite of
intel_enable_gt_powersave to make this more consistent.
Originally this was prep work for future patches, but I've chased down
a totally wrong alley. Still, I think this is a sensible
clarification.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of calling each one for each generation indiviudally.
Notice that we've already managed to be inconsistent, the resume path
is missing an IS_VLV check. As a nice benefit we can mark all the
platform specific enable/disable functions as static and hide them in
intel_pm.c
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP53AxAAoJEHm+PkMAQRiGs2QH/RaqkXz96fwjhDcyiKpDqA3c
kGuS5mz5cOhnqKSmR88HFm6pwuhLux/qSJzeAmoQy1MC8a0ACx7AnANW0lfN3/qe
/HGYz8h60yCL/fhn8/bUYtdt9xsoDqoDcq/ooFl9mcsJGWbC6WeMSZU5dAUYqviE
qFrp5zjY07FG53CRGT0hFpezQNwNL+VLH30CF9LD+fJLPVEYum2zBNGXWM42rcw5
fxzGL/6SO8YqA/Upic1ht6HAd6s5LOrlST7qvnyXUMvRXN5z/Y92ueYJZefkS1Om
ohuLIKM2bv9/dJS67H8N2baSKGCzBdfSe5/5WaHdLYW9MiVju0wRl6HPJtAMrkk=
=H8t8
-----END PGP SIGNATURE-----
Merge tag 'v3.5-rc4' into drm-intel-next-queued
I want to merge the "no more fake agp on gen6+" patches into
drm-intel-next (well, the last pieces). But a patch in 3.5-rc4 also
adds a new use of dev->agp. Hence the backmarge to sort this out, for
otherwise drm-intel-next merged into Linus' tree would conflict in the
relevant code, things would compile but nicely OOPS at driver load :(
Conflicts in this merge are just simple cases of "both branches
changed/added lines at the same place". The only tricky part is to
keep the order correct wrt the unwind code in case of errors in
intel_ringbuffer.c (and the MI_DISPLAY_FLIP #defines in i915_reg.h
together, obviously).
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_ringbuffer.c
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ValleyView is similar to IbexPeak here, but with different register
offsets.
v2: use SDVOB instead ov VLV_HDMIB (Daniel)
drop unnecessary eDP check in DP_C init (Daniel)
eDP support will be coming later from Shobit.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add some VLV limit structures and update the PLL code.
v2: resolve conflicts, Vijay to re-post with PLL valid checks and fixed limits
v3: re-add dpio write function
v4: squash in Vijay's fixes for the PLL limits and clean up the m/n finder
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Somehow this went unnoticed in the past reviews, but the condition would
never timeout properly.
This was initially introduced in the v2 of original SBI enabling patch.
Highly embarrassing.
Note that we now actually time out for the read, which resulted in gcc
complaining that we can now return unitialized garbage if that
happens. There's not much we can do here because there's not much
point in thread -EIO all the way down through these functions. Hence
simply shut up the compiler.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: Added note and squashed uninitialized value shut-up into this
patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This prevents the HDMI detect functions from poking at an eDP
connected panel, which can lead to trouble.
[danvet: Note that we have some other reports of DP vs. HDMI fighting,
but the general case is a much bigger fish to fry.]
References: https://bugs.freedesktop.org/show_bug.cgi?id=42278
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Lenovo Thinkpad T410 has the LVDS_PIPEB_SELECT bit set in the LVDS
register when booted with the lid closed, even though the LVDS hasn't
really been initialized. Ignore this bit so that the VBT value will be
used instead.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For that to work we need to export the base address of the gtt
mmio window from intel-gtt. Also replace all other uses of
dev->agp by values we already have at hand.
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Regroup definitions for BLC_PWM_CTL so that they're all together and
and ordered according to the bitfields.
- Add all missing definitions for BLC_PWM_CTL2.
- Use the BLM_ (for backlight modulation) prefix consistently.
- Note that combination mode (i.e. also taking the legacy backlight
control value from pci config space into account) is gen4 only.
- Move the new registers for PCH-split machines up, they're an almost
match for the gen4 defitions. Prefix the special PCH-only bits with
BLM_PCH_. Also add the pipe C select bit for ivb.
- Rip out the second pair of PCH polarity definitions - they're only
valid on early (pre-production) ilk silicon.
- Adapt the existing code to use the new definitions. This has the
nice benefit of killing a magic (1 << 30) left behind be Jesse
Barnes.
No functional changes in this patch.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Or at least plug another gapping hole. Apparrently hw desingers only
moved the bit field, but did not bother ot re-enumerate the planes
when adding support for a 3rd pipe.
Discovered by i-g-t/flip_test.
This may or may not fix the reference bugzilla, because that one
smells like we have still larger fish to fry.
v2: Fixup the impossible case to catch programming errors, noticed by
Chris Wilson.
References: https://bugs.freedesktop.org/show_bug.cgi?id=50069
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Eugeni Dodonov <eugeni.dodonov@intel.com>
Cc: stable@vger.kernel.org
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of abusing mode->clock by storing it in there - we
shouldn't touch that one at all. This patch is the first prep step to
constify the mode argument of the intel_dp_mode_fixup function.
The next patch will stop us from modifying mode->clock.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need the latest dma-buf code from Dave Airlie so that we can pimp
the backing storage handling code in drm/i915 with Chris Wilson's
unbound tracking and stolen mem backed gem object code.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse extracted this nice helper in his i9xx_crtc_mode_set refactor,
but we have the identical code in ironlake_ccrtc_mode_set. And that
function is huge, so extracting some code full of magic numbers is
always nice.
Noticed while trying to get a handle on our dp clock code.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Already discovered in
commit 5a117db77e
Author: Eugeni Dodonov <eugeni.dodonov@intel.com>
Date: Thu Jan 5 09:34:29 2012 -0200
drm/i915: there is no pipe CxSR on ironlake
but we've failed to rip out the code from the ironlake specific code.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: tune down the noise of the RP irq limit fail
drm/i915: Remove the error message for unbinding pinned buffers
drm/i915: Limit page allocations to lowmem (dma32) for i965
drm/i915: always use RPNSWREQ for turbo change requests
drm/i915: reject doubleclocked cea modes on dp
drm/i915: Adding TV Out Missing modes.
drm/i915: wait for a vblank to pass after tv detect
drm/i915: no lvds quirk for HP t5740e Thin Client
drm/i915: enable vdd when switching off the eDP panel
drm/i915: Fix PCH PLL assertions to not assume CRTC:PLL relationship
drm/i915: Always update RPS interrupts thresholds along with frequency
drm/i915: properly handle interlaced bit for sdvo dtd conversion
drm/i915: fix module unload since error_state rework
drm/i915: be more careful when returning -ENXIO in gmbus transfer
