Add optional blockread function to interface driver. If available
the chip driver uses it for data register access. For 12 bit device
it reads 6 bytes to get 3*16bit data. For 8 bit device it reads out
5 bytes since every second byte is dummy.
This optimizes bus usage and reduces number of operations and
interrupts needed for one data update.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Default fuziness is set smaller for 8 device.
In 12 bit device LSB is quite close to 1 mg
(mg = 1 / 1000 of earth gravity).
In 8bit device LSB is about 18 mg.
Set fuziness to 1 for 8 bit device.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Added default output data rate setting to platform data.
If default rate is 0, reset default value is used.
Added control for duration via platform data.
Added possibility to configure interrupts to trig on
both rising and falling edge. The lis3 WU unit can be
configured quite many ways and with some configurations it
is quite handy to get coordinate refresh when some
event trigs and when it reason goes away.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
All axis enable bits are set to 0 at module remove.
Restore reset default value at init.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Sometimes lis3 chip seems to fail to setup factory tuning at boot up.
This probably happens if there is some odd power ramp down ramp up sequence
for example in device restart. Set boot bit in control2 register to
trig boot sequence manually and wait until it is finished.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Call input device poll function at device open to refresh coordinates
immediately. This is needed for the case where poll interval is set to
zero and coordinate updates happens purely under interrupt control.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Irqcfg moved to chip data instead of platform data.
This simplifies access in interrupt handler little bit.
Input device open and close functions set status for
interrupt threaded handler once.
Unnecessary check for interrupt source removed since
it is enough that active interrupt line indicates that
there was an interrupt.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Based on pm_runtime control, turn lis3 regulators on and off.
Perform context save and restore on transitions.
Feature is optional and must be enabled in platform data.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add pm_runtime support to lis3 core driver.
Add pm_runtime support to lis3 i2c driver.
spi and hp_accel drivers are not yet supported. Old always
on functionality remains for those.
For sysfs there is 5 second delay before turning off the
chip to avoid long ramp up delay.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds hwmon support for fans connected to GPIO lines.
Platform specific information such as GPIO pinout and speed conversion array
(rpm from/to GPIO value) are passed to the driver via platform_data.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
According to the documentation, simply reading the respective MSR
isn't sufficient: It should be written with zeros, cpuid(1) be
executed, and then read (see arch/x86/kernel/cpu/intel.c for an
example).
v2: Fail probe when microcode revision cannot be determined, but is
needed to check for proper operation.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
CONFIG_HOTPLUG_CPU is used too much in some drivers.
This patch clean them up.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
pkgtemp is derived from coretemp, so some reasonable
logics should be applied onto pkgtemp, too. Such as
the init logic here.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This driver adds support for Linear Technology LTC4261 I2C Negative
Voltage Hot Swap Controller.
Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The axis-mapping of lis3dev device on many (rather most) HP machines
doesn't follow the standard. When each new model appears, users need to
adjust again. Testing this requires the rebuild of kernel, thus it's not
trivial for end-users.
This patch adds a module parameter "axes" to allow a custom axis-mapping
without patching and recompiling the kernel driver. User can pass the
parameter such as axes=3,2,1. Also it can be changed via sysfs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch is an enhanced version of Takashi Iwai's
[PATCH] hp_accel: Add quirks for HP ProBook 532x and HP Mini 5102
My HP Mini 5101 works fine with this patch.
Confirmed with Tux Racer.
Signed-off by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
A new version of LIS3 chip has slight incompatibilities from former
versions. This patch adds the minimal support for it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
These likely originate from these drivers being clones of one another
and/or other drivers which actually needed these includes.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
"break" after "return" is at best bogus (good compilers even warn about
the "break" being unreachable).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
... as they're being called only from a __cpuinit function.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (44 commits)
eeepc-wmi: Add cpufv sysfs interface
eeepc-wmi: add additional hotkeys
panasonic-laptop: Simplify calls to acpi_pcc_retrieve_biosdata
panasonic-laptop: Handle errors properly if they happen
intel_pmic_gpio: fix off-by-one value range checking
IBM Real-Time "SMI Free" mode driver -v7
Add OLPC XO-1 rfkill driver
Move hdaps driver to platform/x86
ideapad-laptop: Fix Makefile
intel_pmic_gpio: swap the bits and mask args for intel_scu_ipc_update_register
ideapad: Add param: no_bt_rfkill
ideapad: Change the driver name to ideapad-laptop
ideapad: rewrite the sw rfkill set
ideapad: rewrite the hw rfkill notify
ideapad: use EC command to control camera
ideapad: use return value of _CFG to tell if device exist or not
ideapad: make sure we bind on the correct device
ideapad: check VPC bit before sync rfkill hw status
ideapad: add ACPI helpers
dell-laptop: Add debugfs support
...
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
block: autoconvert trivial BKL users to private mutex
drivers: autoconvert trivial BKL users to private mutex
ipmi: autoconvert trivial BKL users to private mutex
mac: autoconvert trivial BKL users to private mutex
mtd: autoconvert trivial BKL users to private mutex
scsi: autoconvert trivial BKL users to private mutex
Fix up trivial conflicts (due to addition of private mutex right next to
deletion of a version string) in drivers/char/pcmcia/cm40[04]0_cs.c
The hdaps driver isn't a hardware monitoring driver, so it shouldn't
live under driver/hwmon. drivers/platform/x86 seems much more
appropriate, as the driver is only useful on x86 laptops.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.
None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.
Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.
These drivers do not seem to be under active
maintainance from my brief investigation. Apologies
to those maintainers that I have missed.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Sleep while acquiring a resource lock on the Super I/O port. This should
prevent collisions from causing the hardware probe to fail with -EBUSY.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Commit e40cc4bdfd introduced
a build breakage if CONFIG_SMP is undefined. This commit
fixes the problem.
This fix is only a workaround. For a real fix, cpu_sibling_mask() should
be defined in UP include code, eg in linux/smp.h, and asm/smp.h should not be
included directly. This fix is currently not possible because asm/smp.h defines
cpu_sibling_mask() unconditionally and is included directly from many source
files.
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Other than coretemp, from which this code was apparently derived, there
is no PCI specific code in this driver.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Just like pkgtemp registers another core of the same package when one
gets removed, coretemp should register another hyperthread (if
available) in that situation.
As pointed out in the patch fixing the respective code in pkgtemp, the
list protectng mutex must be dropped before calling
coretemp_device_add(), and due to the restructured loop (including an
explicit return) the "safe" variant of the list iterator isn't needed
anymore.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Feature availability should also be checked in the hotplug code path.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Using cpuid_eax() to determine feature availability on other than
the current CPU is invalid. And feature availability should also be
checked in the hotplug code path.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
pkgtemp_device_remove(), holding the list protecting mutex, calls
pkgtemp_device_add(), which itself wants to acquire the same mutex.
Holding the mutex over the entire loop body in pkgtemp_device_remove()
isn't really necessary, as long as the loop gets exited after
processing the matched CPU.
Once exiting the loop after removing an eventual match, there's no
need for using the "safe" list iterator anymore.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
In commit 0dca94baea the call to
platform_driver_unregister() was made conditional upon !HOTPLUG_CPU,
but the return value from coretemp_init() was left to indicate an
error. This isn't correct, as the negative return value indicates to
the module loader that initialization failed, which isn't intended
here and results in dangling pointers.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The recent addition of threaded irq handler causes a NULL dereference
when used with hp_accel driver, which has NULL pdata.
Acked-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
update_interval is the matching attribute defined in the hwmon sysfs ABI.
Use it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The attribute reflects an interval, not a rate.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
According to the datasheet for Winbond W83627DHG the proper way to exit
the Extended Function Mode is to write 0xaa to the EFER(0x2e or 0x4e).
Signed-off-by: Jonas Jonsson <jonas@ludd.ltu.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It is unnecessary and wrong to call hwmon_device_unregister in error
handling before hwmon_device_register is called.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
All bits in the values read from registers to be used for the next
write were getting overwritten, avoid doing so to not mess with the
current configuration.
Signed-off-by: Guillem Jover <guillem@hadrons.org>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The spec notes that fan0 and fan1 control mode bits are located in bits
7-6 and 5-4 respectively, but the FAN_CTRL_MODE macro was making the
bits shift by 5 instead of by 4.
Signed-off-by: Guillem Jover <guillem@hadrons.org>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If CONFIG_PM was selected and lis3lv02d_platform_data was NULL,
the kernel will be panic when halt command run.
Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Sigend-off-by: Jean Delvare <khali@linux-fr.org>
Added missing axis-mapping for HP ProBook 532x and HP Mini 5102.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 8bf0223ed515be24de0c671eedaff49e78bebc9c (hwmon, k8temp: Fix
temperature reporting for ASB1 processor revisions) fixed temperature
reporting for ASB1 CPUs. But those CPU models (model 0x6b, 0x6f, 0x7f)
were packaged both as AM2 (desktop) and ASB1 (mobile). Thus the commit
leads to wrong temperature reporting for AM2 CPU parts.
The solution is to determine the package type for models 0x6b, 0x6f,
0x7f.
This is done using BrandId from CPUID Fn8000_0001_EBX[15:0]. See
"Constructing the processor Name String" in "Revision Guide for AMD
NPT Family 0Fh Processors" (Rev. 3.46).
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: stable@kernel.org [.32.x, .33.x, .34.x, .35.x]
Reported-by: Vladislav Guberinic <neosisani@gmail.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix the following build warning:
CC [M] drivers/hwmon/coretemp.o
drivers/hwmon/coretemp.c: In function "coretemp_init":
drivers/hwmon/coretemp.c:521: warning: unused variable "n"
drivers/hwmon/coretemp.c:521: warning: unused variable "p"
Introduced by commit 851b29cb3b. When
you drop code, you also have to drop the variables this code was
using.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Revert commit 7721fea3d0 ("hwmon:
f71882fg: add support for the Fintek F71808E").
Hans said:
: A second review after I've received a data sheet for this device from
: Fintek has turned up a few bugs.
:
: Unfortunately Giel (nor I) have time to fix this in time for the 2.6.36
: cycle. Therefor I would like to see this patch reverted as not having any
: support for the hwmon function of this superio chip is better then having
: unreliable support.
Cc: Giel van Schijndel <me@mortis.eu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The via-cputemp hwmon driver was probably intending "typedef enum {
... } SHOW;", but the "typedef" was missing creating a global variable
named "SHOW". There is absolutely no reason to have this in the
global namespace.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
jc42 uses i2c interfaces, so it should depend on I2C.
drivers/hwmon/jc42.c:426: error: implicit declaration of function 'i2c_check_functionality'
drivers/hwmon/jc42.c:521: error: implicit declaration of function 'i2c_smbus_read_word_data'
drivers/hwmon/jc42.c:529: error: implicit declaration of function 'i2c_smbus_write_word_data'
drivers/hwmon/jc42.c:580: error: implicit declaration of function 'i2c_add_driver'
drivers/hwmon/jc42.c:585: error: implicit declaration of function 'i2c_del_driver'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The sysfs file removal code is the same in the probe error path and in
the remove function, so move it to a separate function to avoid code
duplication.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for the 6 temperature monitoring channels of the PC87427.
Note that the sensors resolution can vary, and I couldn't find a way
to figure it out, so we might have to compensate in user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The second logical device contains the voltage and temperature
registers. We have to extend the driver to support a second logical
device before we can add support for these features.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add initial support for PWM outputs of the PC87427 Super-I/O chip.
Only mode change and manual fan speed control are supported. Automatic
mode configuration isn't supported, and won't be until at least one
board is known, which makes uses of the PWM outputs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Most fan input pins of the PC87427 can have alternate functions.
Update the driver to check the configuration register and only support
fan inputs which are really used for fan monitoring.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for W83667HG-B (very similar to the W83667HG).
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
- Moved fan pwm register array pointers into per-instance data.
- Only read fan pwm data for installed/supported fans.
- Update fan max output and fan step output information from data in
registers.
- Create max_output and step_output attribute files only if respective
fan pwm registers exist.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
SMSC's EMC2103 family of temperature/fan controllers have 1
onboard and up to 3 external temperature sensors, and allow
closed-loop control of one fan. This patch adds support for
them.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* The dev variable is never used.
* Detect functions only need to set info->type, not client->name.
* Include the device address in the log message.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: George Joseph <george.joseph@fairview5.com>
Cc: Ken Milmore <ken.milmore@googlemail.com>
Some voltage sensors can be wired internally to the IT87xxF chip's own
power supply channels. In that case, we can inform user-space that the
wiring is known by exporting proper labels for these sensors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is a shutdown feature at suspend it can be enabled to
reduce current consumption and resume it can be switched off.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add back the power interface we lost due to a slight misunderstanding of
the maintainers wishes.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for exposing all GPIO pins as analog voltages. Though this is
not an ideal use of the chip, some hardware engineers may decide that the
LTC4245 meets their design requirements when studying the datasheet.
The GPIO pins are sampled in round-robin fashion, meaning that a slow
reader will see stale data. A userspace application can detect this,
because it will get -EAGAIN when reading from a sysfs file which contains
stale data.
Users can choose to use this feature on a per-chip basis by using either
platform data or the OF device tree (where applicable).
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It's not OK to call platform_device_add_resources() multiple times
in a row. Despite its name, this functions sets the resources, it
doesn't add them. So we have to prepare an array with all the
resources, and then call platform_device_add_resources() once.
Before this fix, only the last I/O resource would be actually
registered. The other I/O resources were leaked.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: stable@kernel.org
Move the if(err) statement after the if into the if branch indicated by its
indentation. The preceding if(err) test implies that err cannot be nonzero
unless the if branch is taken.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces5@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p4)
cocci.print_secs("after",p5)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is a shiny new mc13783 API function that can be used instead.
While at it refactor the code a bit to reduce code duplication a bit.
This removes the last user of <linux/mfd/mc13783-private.h> and so this
include file can go away.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In commit 0dca94baea ("hwmon: coretemp: update hotplug condition
check") we merged v2 of this patch. Update that to v3.
The difference is to remove the new and unnecesary references to
CPU_*_FROZEN.
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow device probing to recognise the Fintek F71808E.
Sysfs interface:
* Fan/pwm control is the same as for F71889FG
* Temperature and voltage sensor handling is largely the same as for
the F71889FG
- Has one temperature sensor less (doesn't have temp3)
- Misses one voltage sensor (doesn't have V6, thus in6_input refers to
what in7_input refers for F71889FG)
For the purpose of the sysfs interface fxxxx_in_temp_attr[] is split up
such that it can largely be reused.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
register_hotcpu_notifier() is designed to make these ifdefs unnecessary.
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update coretemp supported CPU TjMax lists and some cleanup work.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If one coretemp device can't be added, it should allow subsequent adding
operation because every new-added device will create a new sysfs group,
not an additional sensor sys entry.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix two errors in hotplug. One is for hotplug notifier. The other is
unnecessary driver unregister. Because even none of online cpus supports
coretemp, we can't assume new onlined cpu doesn't support it either. If
related driver is unregistered there we have no chance to use coretemp
from then on.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver adds support for the monitoring features of the Summit
Microelectronics SMM665 Six-Channel Active DC Output Controller/Monitor.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add Lenovo Thinkpad T400. I have done the testing on my laptop. The
hdaps module detects the device and the hdapsd daemon is able to [un]park
the disk.
Signed-off-by: Ritesh Raj Sarraf <rrs@debian.org>
Cc: Frank Seidel <frank@f-seidel.de>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (63 commits)
of/platform: Register of_platform_drivers with an "of:" prefix
of/address: Clean up function declarations
of/spi: call of_register_spi_devices() from spi core code
of: Provide default of_node_to_nid() implementation.
of/device: Make of_device_make_bus_id() usable by other code.
of/irq: Fix endian issues in parsing interrupt specifiers
of: Fix phandle endian issues
of/flattree: fix of_flat_dt_is_compatible() to match the full compatible string
of: remove of_default_bus_ids
of: make of_find_device_by_node generic
microblaze: remove references to of_device and to_of_device
sparc: remove references to of_device and to_of_device
powerpc: remove references to of_device and to_of_device
of/device: Replace of_device with platform_device in includes and core code
of/device: Protect against binding of_platform_drivers to non-OF devices
of: remove asm/of_device.h
of: remove asm/of_platform.h
of/platform: remove all of_bus_type and of_platform_bus_type references
of: Merge of_platform_bus_type with platform_bus_type
drivercore/of: Add OF style matching to platform bus
...
Fix up trivial conflicts in arch/microblaze/kernel/Makefile due to just
some obj-y removals by the devicetree branch, while the microblaze
updates added a new file.
This patch adds a hwmon driver for package level thermal control. The driver
dumps package level thermal information through sysfs interface so that upper
level application (e.g. lm_sensor) can retrive the information.
Instead of having the package level hwmon code in coretemp, I write a seperate
driver pkgtemp because:
First, package level thermal sensors include not only sensors for each core,
but also sensors for uncore, memory controller or other components in the
package. Logically it will be clear to have a seperate hwmon driver for package
level hwmon to monitor wider range of sensors in a package. Merging package
thermal driver into core thermal driver doesn't make sense and may mislead.
Secondly, merging the two drivers together may cause coding mess. It's easier
to include various package level sensors info if more sensor information is
implemented. Coretemp code needs to consider a lot of legacy machine cases.
Pkgtemp code only considers platform starting from Sandy Bridge.
On a 1Sx4Cx2T Sandy Bridge platform, lm-sensors dumps the pkgtemp and coretemp:
pkgtemp-isa-0000
Adapter: ISA adapter
physical id 0: +33.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0001
Adapter: ISA adapter
Core 1: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0002
Adapter: ISA adapter
Core 2: +32.0°C (high = +79.0°C, crit = +99.0°C)
coretemp-isa-0003
Adapter: ISA adapter
Core 3: +32.0°C (high = +79.0°C, crit = +99.0°C)
[ hpa: folded v3 patch removing improper global variable "SHOW" ]
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
LKML-Reference: <1280448826-12004-3-git-send-email-fenghua.yu@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Both of_bus_type and of_platform_bus_type are just #define aliases
for the platform bus. This patch removes all references to them and
switches to the of_register_platform_driver()/of_unregister_platform_driver()
API for registering.
Subsequent patches will convert each user of of_register_platform_driver()
into plain platform_drivers without the of_platform_driver shim. At which
point the of_register_platform_driver()/of_unregister_platform_driver()
functions can be removed.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Don't assume that CPU entry number and core ID always match. It
worked in the simple cases (single CPU, no HT) but fails on
multi-CPU systems.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Cc: stable@kernel.org
On hyper-threaded CPUs, each core appears twice in the CPU list. Skip
the second entry to avoid duplicate sensors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Cc: stable@kernel.org
The IT8720F has no VIN7 pin, so VCCH should always be routed
internally to VIN7 with an internal divider. Curiously, there still
is a configuration bit to control this, which means it can be set
incorrectly. And even more curiously, many boards out there are
improperly configured, even though the IT8720F datasheet claims that
the internal routing of VCCH to VIN7 is the default setting. So we
force the internal routing in this case.
It turns out that all boards with the wrong setting are from Gigabyte,
so I suspect a BIOS bug. But it's easy enough to workaround in the
driver, so let's do it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jean-Marc Spaggiari <jean-marc@spaggiari.org>
Cc: stable@kernel.org
Reported temperature for ASB1 CPUs is too high.
Add ASB1 CPU revisions (these are also non-desktop variants) to the
list of CPUs for which the temperature fixup is not required.
Example: (from LENOVO ThinkPad Edge 13, 01972NG, system was idle)
Current kernel reports
$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +74.0 C
Core0 Temp: +70.0 C
Core1 Temp: +69.0 C
Core1 Temp: +70.0 C
With this patch I have
$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +54.0 C
Core0 Temp: +51.0 C
Core1 Temp: +48.0 C
Core1 Temp: +49.0 C
Cc: stable@kernel.org [.32.x .33.x, .34.x]
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Commit a2e066bba2 introduced core
swapping for CPU models 64 and later. I recently had a report about
a Sempron 3200+, model 95, for which this patch broke temperature
reading. It happens that this is a single-core processor, so the
effect of the swapping was to read a temperature value for a core
that didn't exist, leading to an incorrect value (-49 degrees C.)
Disabling core swapping on singe-core processors should fix this.
Additional comment from Andreas:
The BKDG says
Thermal Sensor Core Select (ThermSenseCoreSel)-Bit 2. This bit
selects the CPU whose temperature is reported in the CurTemp
field. This bit only applies to dual core processors. For
single core processors CPU0 Thermal Sensor is always selected.
k8temp_probe() correctly detected that SEL_CORE can't be used on single
core CPU. Thus k8temp did never update the temperature values stored
in temp[1][x] and -49 degrees was reported. For single core CPUs we
must use the values read into temp[0][x].
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Rick Moritz <rhavin@gmx.net>
Acked-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: stable@kernel.org
i5k_amb.ko uses dynamically allocated memory (by kmalloc) for
attributes passed to sysfs. So, sysfs_attr_init() should be called
for working happy with lockdep.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org [2.6.34 only]
When detecting AM2+ or AM3 socket with DDR2, only blacklist cores
which are known to exist in AM2+ format.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: stable@kernel.org
I2C drivers can use the clientdata-pointer to point to private data. As I2C
devices are not really unregistered, but merely detached from their driver, it
used to be the drivers obligation to clear this pointer during remove() or a
failed probe(). As a couple of drivers forgot to do this, it was agreed that it
was cleaner if the i2c-core does this clearance when appropriate, as there is
no guarantee for the lifetime of the clientdata-pointer after remove() anyhow.
This feature was added to the core with commit
e4a7b9b04d to fix the faulty drivers.
As there is no need anymore to clear the clientdata-pointer, remove all current
occurrences in the drivers to simplify the code and prevent confusion.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the Texas Instruments TMP105 temperature sensor
device.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti@ti.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Read only one of the GPIO pins as an analog voltage. The ADC can be
switched to a different GPIO pin at runtime, but this is not supported.
Previously, this driver would report the analog voltage of the currently
selected GPIO pin as all three GPIO voltages: in9_input, in10_input and
in11_input.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Add support for the hardware monitoring capabilities of the SCH5127
chip to the dme1737 driver.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Jeff Rickman <jrickman@myamigos.us>
Only stop the chip at driver exit if it was stopped when driver was
loaded. Leave it running otherwise.
Also restore the device configuration if probe failed, to not leave
the system in a dangling state.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Steven King <sfking@fdwdc.com>
Suspend and resume functions shouldn't overwrite the configuration
register. They should only alter the one bit they have to touch.
Also don't assume that register reads and writes always succeed.
Handle errors properly, shall they happen.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Steven King <sfking@fdwdc.com>
Fixes from my driver review:
http://lists.lm-sensors.org/pipermail/lm-sensors/2010-March/028051.html
Only the small changes are in there, more important changes will come
later separately as time permits.
* Drop the remnants of the now gone detect function
* The TMP102 has no known compatible chip
* Include the right header files
* Clarify why byte swapping of register values is needed
* Strip resolution info bit from temperature register value
* Set cache lifetime to 1/3 second
* Don't arbitrarily reject limit values; clamp as needed
* Make limit writing unconditional
* Don't check for transaction types the driver doesn't use
* Properly check for error when setting configuration
* Report error on failed probe
* Make the driver load automatically where needed
* Various other minor fixes
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Steven King <sfking@fdwdc.com>
Driver for the TI TMP102.
The TI TMP102 is similar to the LM75. It differs from the LM75 by
having a 16-bit conf register and the temp registers have a minimum
resolution of 12 bits; the extended conf register can select 13-bit
resolution (which this driver does) and also change the update rate
(which this driver currently doesn't use).
[JD: Fix tmp102_exit tag, must be __exit, not __init.]
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Provides support for the EMC1403 thermal sensor. Only reporting of values
is supported. The various Moorestown specific extras to do with thermal
alerts and the like are not in this version of the driver.
Considerably edited and tidied up by Alan Cox, plus fixes and detection
bits from Jean Delvare.
Signed-off-by: Kalhan Trisal <kalhan.trisal@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The Apple SMC uses a systematic labeling scheme for the hardware
temperature sensors. This scheme is currently hidden from
userland. Since the sensor set, and consequently the numbering,
differs between models, an extensive database of configurations is
required for an application such as fan control. This patch adds the
SMC labels to the hwmon sysfs interface, allowing applications to use
the sensors more intelligibly.
[rydberg@euromail.se: fixed error handling]
Signed-off-by: Alex Murray <murray.alex@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds generic support for the MacBook Pro 7 family
based on the 7,1 model.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds generic support for the MacBook Pro 6 family
based on the 6,2 model.
[rydberg@euromail.se: patch cleanup]
Signed-off-by: Bernhard Froemel <froemel@vmars.tuwien.ac.at>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The MacBookPro 5,3 model has two fans, whereas the 5,4 model has
only one. This patch adds explicit support for the 5,3 and 5,4 models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Replace octal representation of file permissions by the corresponding
constants.
Signed-off-by: Andre Prendel <andre.prendel@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Based on earlier work by Ira W. Snyder.
The adm1031 chip is capable of using a runtime configurable sampling rate,
using the fan filter register. Add support for reading and setting the
update rate via sysfs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
The lm90 driver programs the sensor chip to update its readings at 2 Hz
(500 ms between readings). However, the driver only does reads from the
chip at intervals of 2 * HZ (2000 ms between readings). Change the driver
update rate to the programmed update rate.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acquire the I/O region for the Super I/O chip while we're working on it.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Some code cleanup: properly use previously defined functions, rather
than duplicating their code.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use the strict_strol and strict_stroul functions instead of simple_strol
and simple_stroul respectively in sysfs functions.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fixed several coding style issues.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM64 appears to be an LM63 with added GPIO lines. Add support for the
hwmon functionality - GPIO can be added at some later stage if someone
has a need for them.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When the user passes the kernel parameter acpi_enforce_resources=lax,
the ACPI resources are no longer protected, so a native driver can
make use of them. In that case, we do not want the asus_atk0110 to be
loaded. Unfortunately, this driver loads automatically due to its
MODULE_DEVICE_TABLE, so the user ends up with two drivers loaded for
the same device - this is bad.
So I suggest that we prevent the asus_atk0110 driver from loading if
acpi_enforce_resources=lax.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Luca Tettamanti <kronos.it@gmail.com>
Cc: Len Brown <lenb@kernel.org>
The MSR IA32_TEMPERATURE_TARGET contains the TjMax value in the newer
Intel processors.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Yong Wang <yong.y.wang@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The thermal sensors of Intel(R) CPUs can be detected by CPUID instruction,
indicated by CPUID.06H.EAX[0].
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Reviewed-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Yong Wang <yong.y.wang@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Paul Thomas <pthomas8589@gmail.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Content for the 8bit device threaded interrupt handlers. Depending on the
interrupt line and chip configuration, either click or wakeup / freefall
handler is called. In case of click, BTN_ event is sent via input device.
In case of wakeup or freefall, input device ABS_ events are updated
immediatelly.
It is still possible to configure interrupt line 1 for fast freefall
detection and use the second line either for click or threshold based
interrupts. Or both lines can be used for click / threshold interrupts.
Polled input device can be set to stopped state and still get coordinate
updates via input device using interrupt based method. Polled mode and
interrupt mode can also be used parallel.
BTN_ events are remapped based on existing axis remapping information.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Original lis3 driver didn't provide interrupt handler(s) for click or
threshold event handling. This patch adds threaded handlers for one or
two interrupt lines for 8 bit device. Actual content for interrupt
handling is provided in the separate patch.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
8 bit device has two wakeup / free fall units. It was not possible to
configure the second unit. This patch introduces configuration entry to
the platform data and also corresponding changes to the 8 bit setup
function.
High pass filters were enabled by default. Patch introduces configuration
option for high pass filter cut off frequency and also possibility to
disable or enable the filter via platform data. Since the control is a
new one and default state was filter enabled, new option is used to
disable the filter. This way old platform data is still compatible with
the change.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Separate configuration function for 8 bit version of the chip. This way
generic part of the init function stays little bit more readable.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Definitions for click were missing.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'bkl/ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/random-tracing:
uml: Pushdown the bkl from harddog_kern ioctl
sunrpc: Pushdown the bkl from sunrpc cache ioctl
sunrpc: Pushdown the bkl from ioctl
autofs4: Pushdown the bkl from ioctl
uml: Convert to unlocked_ioctls to remove implicit BKL
ncpfs: BKL ioctl pushdown
coda: Clean-up whitespace problems in pioctl.c
coda: BKL ioctl pushdown
drivers: Push down BKL into various drivers
isdn: Push down BKL into ioctl functions
scsi: Push down BKL into ioctl functions
dvb: Push down BKL into ioctl functions
smbfs: Push down BKL into ioctl function
coda/psdev: Remove BKL from ioctl function
um/mmapper: Remove BKL usage
sn_hwperf: Kill BKL usage
hfsplus: Push down BKL into ioctl function
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
These are the last remaining device drivers using
the ->ioctl file operation in the drivers directory
(except from v4l drivers).
[fweisbec: drop i8k pushdown as it has been done from
procfs pushdown branch already]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
The work queue has to be flushed after the device has been made
inaccessible. The patch closes a window during which a work queue might
remain active after the device is removed and would then lead to ACPI
calls with undefined behavior.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Pavel Herrmann <morpheus.ibis@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current code will not remove the sysfs files for fan numbers three
and up. Also, upon exit, fans one and two are removed regardless of
their existence. This patch cleans up the sysfs error handling for
the fans.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* Allow fan minimum RPM to be set to zero without triggering alarms.
* Fix voltage scaling arithmetic and correct scale factors.
* Correct fan1-fan4 alarm bit shifts.
* Correct register address for temp3_smoothing_enable.
* Read the alarm registers with high priority.
Signed-off-by: Ken Milmore <ken.milmore@googlemail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Correct axis-mappings for new HP ProBook laptops.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Annotate dynamic sysfs attribute in atk_create_files(). This gets
rid of the following lockdep warning:
BUG: key ffff8800379ca670 not in .data!
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:2696 lockdep_init_map+0xd2/0x108()
Hardware name: P5K PRO
Modules linked in: asus_atk0110(+) pata_acpi firewire_ohci ata_generic
dm_multipath firewire_core crc_itu_t pata_marvell floppy
Pid: 599, comm: modprobe Not tainted 2.6.34-rc4 #27
Call Trace:
[<ffffffff8104cdb0>] warn_slowpath_common+0x7c/0x94
[<ffffffff8104cddc>] warn_slowpath_null+0x14/0x16
[<ffffffff81077c4d>] lockdep_init_map+0xd2/0x108
[<ffffffff81165873>] sysfs_add_file_mode+0x66/0xa2
[<ffffffff811658c0>] sysfs_add_file+0x11/0x13
[<ffffffff8116594b>] sysfs_create_file+0x2a/0x2c
[<ffffffff812c1f9c>] device_create_file+0x19/0x1b
[<ffffffffa005b4fd>] atk_add+0x58b/0x72e [asus_atk0110]
[<ffffffff812572a1>] acpi_device_probe+0x50/0x122
[<ffffffff812c46af>] driver_probe_device+0xa2/0x127
[<ffffffff812c4783>] __driver_attach+0x4f/0x6b
[<ffffffff812c4734>] ? __driver_attach+0x0/0x6b
[<ffffffff812c3c94>] bus_for_each_dev+0x59/0x8e
[<ffffffff812c4519>] driver_attach+0x1e/0x20
[<ffffffff812c4152>] bus_add_driver+0xb9/0x207
[<ffffffff812c4a5f>] driver_register+0x9d/0x10e
[<ffffffffa005f000>] ? atk0110_init+0x0/0x31 [asus_atk0110]
[<ffffffff81257c7c>] acpi_bus_register_driver+0x43/0x45
[<ffffffffa005f015>] atk0110_init+0x15/0x31 [asus_atk0110]
[<ffffffffa005f000>] ? atk0110_init+0x0/0x31 [asus_atk0110]
[<ffffffff81002069>] do_one_initcall+0x5e/0x15e
[<ffffffff81085075>] sys_init_module+0xd8/0x239
[<ffffffff81009cf2>] system_call_fastpath+0x16/0x1b
---[ end trace 4d0c84007055efb9 ]---
BUG: key ffff8800379ca638 not in .data!
BUG: key ffff8800379ca6a8 not in .data!
BUG: key ffff8800379ca6e0 not in .data!
BUG: key ffff880036f73670 not in .data!
BUG: key ffff880036f73638 not in .data!
BUG: key ffff880036f736a8 not in .data!
BUG: key ffff880036f736e0 not in .data!
BUG: key ffff880036f76c70 not in .data!
BUG: key ffff880036f76c38 not in .data!
BUG: key ffff880036f76ca8 not in .data!
BUG: key ffff880036f76ce0 not in .data!
BUG: key ffff8800368e7670 not in .data!
BUG: key ffff8800368e7638 not in .data!
BUG: key ffff8800368e76a8 not in .data!
BUG: key ffff8800368e76e0 not in .data!
BUG: key ffff880036ef7670 not in .data!
BUG: key ffff880036ef7638 not in .data!
BUG: key ffff880036ef76a8 not in .data!
BUG: key ffff880036ef76e0 not in .data!
BUG: key ffff8800373ccc70 not in .data!
BUG: key ffff8800373ccc38 not in .data!
BUG: key ffff8800373ccca8 not in .data!
BUG: key ffff8800373ccce0 not in .data!
BUG: key ffff880037a60870 not in .data!
BUG: key ffff880037a60838 not in .data!
BUG: key ffff880037a608a8 not in .data!
BUG: key ffff880037a608e0 not in .data!
BUG: key ffff880037355070 not in .data!
BUG: key ffff880037355038 not in .data!
BUG: key ffff8800373550a8 not in .data!
BUG: key ffff8800373550e0 not in .data!
BUG: key ffff8800378c2670 not in .data!
BUG: key ffff8800378c2638 not in .data!
BUG: key ffff8800378c26a8 not in .data!
BUG: key ffff8800378c26e0 not in .data!
BUG: key ffff880036ef7e70 not in .data!
BUG: key ffff880036ef7e38 not in .data!
BUG: key ffff880036ef7ea8 not in .data!
BUG: key ffff880036ef7ee0 not in .data!
Cc: Eric W. Biederman <ebiederm@xmission.com>
Reported-by: Dhaval Giani <dhaval.giani@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Dhaval Giani <dhaval.giani@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the iMac9,1 and the MacBookPro2,2 temperature sensors to hwmon
driver applesmc to fix kernel bug #14429:
https://bugzilla.kernel.org/show_bug.cgi?id=14429
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When any temperature sensor type is changed, the corresponding
temperature value needs to be updated. The register caching mechanism
may delay this update, so we want to invalidate the cache to force an
immediate update.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Currently, if someone tries to set the thermal sensor type to an
unsupported value, subsequent accesses to the chip may temporarily
show the sensor in question as disabled. Use a temporary variable
and only update the cached value on success, to prevent such
confusion.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Temperature channels can be used in 2 different modes (thermistor and
thermal diode) and we don't know which one, if any, is correct for
every given board. So don't arbitrarily choose one. Instead, leave the
temperature channels untouched. They can be configured from user-space
if needed anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When CONFIG_REGULATOR isn't set, regulator_get_voltage() returns 0.
Properly handle this case by not trusting the value.
Reported-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
I discovered two issues.
First the previous sht15_calc_temp() loop did not iterate through the
temppoints array since the (data->supply_uV > temppoints[i - 1].vdd)
test is always true in this direction.
Also the two-points linear interpolation function was returning biased
values due to a stray division by 1000 which shouldn't be there.
[JD: Also change the default value for d1 from 0 to something saner.]
Signed-off-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Intel X58 have asc7621a chip. So added X58 entry in Kconfig for asc7621.
Also arranged existing models in ascending order.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
"ret" is used to store the return value for watchdog_trigger() and it
should be signed for the error handling to work.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add missing newline to dev_warn() message string. This is more of an issue
with older kernels that don't automatically add a newline if it was missing
from the end of the previous line.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Avoid hex and decimal confusion when printing out the cpu model.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (23 commits)
hwmon: Remove the deprecated adt7473 driver
hwmon: Fix off-by-one kind values
hwmon: (tmp421) Fix temperature conversions
hwmon: (tmp421) Restore missing inputs
hwmon: Driver for Andigilog aSC7621 family monitoring chips
hwmon: (adt7411) Improve locking
hwmon: Add driver for ADT7411 voltage and temperature sensor
hwmon: (w83793) Add watchdog functionality
hwmon: (g760a) Make rpm_from_cnt static
hwmon: (it87) Validate auto pwm settings
hwmon: (it87) Add support for old automatic fan speed control
hwmon: (it87) Drop dead web links in documentation
hwmon: (it87) Add an entry in MAINTAINERS
hwmon: (it87) Use strict_strtol instead of simple_strtol
hwmon: (it87) Fix many checkpatch errors and warnings
hwmon: (it87) Add support for beep on alarm
hwmon: (it87) Create vid attributes by group
hwmon: (it87) Refactor attributes creation and removal
hwmon: (it87) Expose the PWM/temperature mappings
hwmon: (it87) Display fan outputs in automatic mode as such
...
While testing an ADC121S021 in an embedded board with a S3C2142 SoC (ARM
core), I have found that the 'adcxx' driver does not handle correctly
single channel ADCs from this chip family. For single channel chips you
must only issue one read transfer for correct measurement.
Signed-off-by: Jose Miguel Goncalves <jose.goncalves@inov.pt>
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
String constants that are continued on subsequent lines with \ will cause
spurious whitespace in the resulting output.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
adt7473 driver is obsoleted by adt7475 driver. And it is scheduled
to be removed in Feb 2010.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Recent changes on the I2C front have left off-by-one array indexes in
3 hwmon drivers. Fix them.
Faulty commit:
e5e9f44c2 i2c: Drop I2C_CLIENT_INSMOD_2 to 8
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andre Prendel <andre.prendel@gmx.de>
Cc: stable@kernel.org
The low bits of temperature registers are status bits, they must be
masked out before converting the register values to temperatures.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Andre Prendel <andre.prendel@gmx.de>
Cc: stable@kernel.org
An off-by-one error caused some inputs to not be created by the driver
when they should. TMP421 gets only one input instead of two, TMP422
gets two instead of three, etc. Fix the bug by listing explicitly the
number of inputs each device has.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Andre Prendel <andre.prendel@gmx.de>
Cc: stable@kernel.org
Hwmon driver for Andigilog aSC7621 family monitoring chips.
Signed-off-by: George Joseph <george.joseph@fairview5.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add proper locking for the cached variables. Also get rid of
ref_is_vdd, which became obsolete.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add basic support for the ADT7411. Reads out all conversion results (via I2C,
SPI yet missing) and allows some on-the-fly configuration. Tested with a
custom board.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add watchdog functionality to the Winbond W83793 driver.
Signed-off-by: Sven Anders <anders@anduras.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Function rpm_from_cnt is only used internally so it can be made
static. Make it inline while we're here, for performance reasons
(although hopefully gcc would figure out by itself...)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
Before switching to automatic fan control mode, make sure that all the
trip points make sense. Otherwise, the control loop could lead to
weird fan behavior.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the automatic fan speed control interface as
implemented by IT8705F chips up to revision F and IT8712F chips up to
revision G. This implementation fits very well in our standard sysfs
interface.
I implemented the old and not the new interface because the only chip
I have at hand is an old one, and the new interface is more difficult
to map to the standard sysfs interface. Adding support later should be
possible though, if someone with a supported chip is interested.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix 20 errors and 11 warnings reported by the checkpatch script. The
remainining errors would require more work. The remaining warnings
will be addressed later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The IT87xxF chips support beeping on alarm, if properly wired and
configured. There is one control bit for each input type (temperature,
fan, voltage.) Let the user see and change them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Only VID-related attributes are left in it87_attributes_opt, so we
might as well rename it to it87_attributes_vid and use this group to
create all attributes at once.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is a lot of code redundancy in the creation of the fan and
pwm attributes. Move these attributes to arrays so that the code can
be simplified.
This in turns makes the attributes removal code larger, so move it to
a separate function that can be called in both the standard removal
case and the error path during probing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let the user read the PWM-to-temperature mappings. Until the trip
points are also exposed, this is essentially a way to know how the
BIOS has set things up. The ability to change the settings will be
added later, together with the trip points.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it87 driver doesn't yet support automatic fan control. Let it at
least tell the user when a fan output is in automatic mode. Also let
the user switch from automatic mode (possibly set by the BIOS) to
manual mode and back without losing the settings.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested successfully with an ADM1032 chip on its evaluation board. It
should work fine with all other chips as well.
At this point this is more of a proof-of-concept, we don't do anything
terribly useful on SMBus alert: we simply log the event. But this could
later evolve into libsensors signaling so that user-space applications
can take an appropriate action.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
Restore the chip configuration when unloading the driver. This ensures
we don't leave the chip running if it was initially stopped.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This chips is found on several Zotac Ion ITX boards, amongst others.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: MC Matti <mcmatti17@googlemail.com>
Cc: Manuel Lamotte-Schubert <mls@pronego.com>
Different motherboards have different PNP declarations for
W83781D/W83782D chips. Some declare the whole range of I/O ports (8
ports), some declare only the useful ports (2 ports at offset 5) and
some declare fancy ranges, for example 4 ports at offset 4. To
properly handle all cases, request all ports individually for probing.
After we have determined that we really have a W83781D or W83782D
chip, the useful port range will be requested again, as a single
block.
I did not see a board which needs this yet, but I know of one for lm78
driver and I'd like to keep the logic of these two drivers in sync.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Different motherboards have different PNP declarations for LM78/LM79
chips. Some declare the whole range of I/O ports (8 ports), some
declare only the useful ports (2 ports at offset 5) and some declare
fancy ranges, for example 4 ports at offset 4. To properly handle all
cases, request all ports individually for probing. After we have
determined that we really have an LM78 or LM79 chip, the useful port
range will be requested again, as a single block.
This fixes the driver on the Olivetti M3000 DT 540, at least.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
The #define ADT7462_VOLT_COUNT is wrong, it should be 13 not 12. All the
for loops that use this as a limit count are of the typical form, "for
(n = 0; n < ADT7462_VOLT_COUNT; n++)", so to loop through all voltages
w/o missing the last one it is necessary for the count to be one greater
than it is. (Specifically, you will miss the +1.5V 3GPIO input with count
= 12 vs. 13.)
Signed-off-by: Ray Copeland <ray.copeland@aprius.com>
Acked-by: "Darrick J. Wong" <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Some code that is in ams_exit() (the module exit code) should instead
be called when the device (not module) is removed. It probably doesn't
make much of a difference in the PMU case, but in the I2C case it does
matter.
I make no guarantee that my fix isn't racy, I'm not familiar enough
with the ams driver code to tell for sure.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When /dev/watchdog gets opened a second time we return -EBUSY, but
we already have got a kref then, so we end up leaking our data struct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
MBIF (motherboard identification) is only used to print the name of
the board, it's not essential for the driver; do not fail if it's
missing. Based on Juan's patch.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: Juan RP <xtraeme@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
smsc47m1_restore is called from sm_smsc47m1_exit, which is an __exit
function, so it can't be __init.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The id_table field of the struct pci_driver is constant in <linux/pci.h>
so it is worth to make pci_device_id also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The max junction temperature of Atom N450/D410/D510 CPUs is 100 degrees
Celsius. Since these CPUs are always coupled with Intel NM10 chipset in
one package, the best way to verify whether an Atom CPU is N450/D410/D510
is to check the host bridge device.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The latest version of the Revision Guide for AMD Family 10h Processors
lists two more processor revisions which may be affected by erratum 319.
Change the blacklisting code to correctly detect those processors, by
implementing AMD's recommended algorithm.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Expose the raw GGRP/GITM interface via debugfs. The hwmon interface is
reverse engineered and the driver tends to break on newer boards...
Using this interface it's possible to poke directly at the ACPI methods
without the need to recompile, reducing the guesswork and the round trips
needed to support a new revision of the interface.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The behaviour is unmodified, this makes easier to override the heuristic (which
is probably needed for some boards).
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The ADT7462_PIN28_VOLT value is a 4-bit field, so the corresponding
shift must be 4.
Signed-off-by: Roger Blofeld <blofeldus@yahoo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (w83627hf) Fix for "No such device"
hwmon: (sht15) Off-by-one error in array index + incorrect constants
hwmon: Add driver for VIA CPU core temperature
hwmon: (smsc47m1) Enable device if needed
hwmon: (smsc47m1) Fail module loading on error
hwmon: (smsc47m1) Only request I/O ports we really use
hwmon: New driver for AMD Family 10h/11h CPUs
The commit b72656dbc4 introduced
a bug leading to the w83627hf_find function no longer finding
any chips.
Signed-off-by: Christian Schulte <cs@schulte.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix an off-by-one error in array index + incorrect constants.
Signed-off-by: Christoph Walser <walser@tik.ee.ethz.ch>
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is a driver for the on-die digital temperature sensor of
VIA's recent CPU models.
[JD: Misc clean-ups.]
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Adam Nielsen <a.nielsen@shikadi.net>
If the address is set but the device isn't enabled, attempt to enable
it. If it won't work for any reason (resource conflict, no function
enabled) the initial state is restored. The initial state is also
restored on module unloading.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Sean Fidler <fidlersean@gmail.com>
If an error occurs during probing, there's no point in keeping the
module in memory. Better fail the module loading early to make the
problem more visible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Sean Fidler <fidlersean@gmail.com>
The I/O area of the SMSC LPC47M1xx chips which we use, gives access to
a lot of registers, some of which are related to fan speed monitoring
and control, but many are not. At the moment, the smsc47m1 driver
requests the whole I/O port range. This could easily result in
resource conflicts with either ACPI or other drivers.
Request only the I/O ports we really use, to prevent such conflicts.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Sean Fidler <fidlersean@gmail.com>
This adds a driver for the internal temperature sensor of AMD Family 10h
and 11h CPUs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Report output values as 1/1000 of earth gravity.
Output values from lis3 can be read from sysfs position entry and from
input device. Input device can be accessed as event device and as
joystick device. Joystick device can be in two modes. Meaning of the
output values varies from case to case depending on the chip type and
configuration (scale). Only joystick interface in JS_CORR_BROKEN mode
returned somehow similar output values in different configurations.
Joystick device is in that state by default in case of lis3.
Position sysfs entry, input event device and raw joystick device have been
little bit broken since meaning of the output values has been varied
between 12 and 8 bit devices. Applications which relayed on those methods
failed if the chip is different than the expected one.
This patch converts output values to mean similar thing in different
configurations. Both 8 and 12 bit devices reports now same acceleration
values. If somebody implements full scale support to the driver, output
values will still mean the same. Scaling factor and input device range
must be updated in that case.
Joystick interface in JS_CORR_BROKEN mode is not touched by this patch.
All other interfaces have different scale after this change. For 12 bit
device scaling factor is 0.977 which keeps scaled and unscaled values are
quite close to each others. For 8 bit device, scaled values are 18 times
bigger than unscaled values.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is possible to read position information at the chip measurement rate
via sysfs. This patch adds possibility to configure chip measurement
rate.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chip is calibrated by the manufacturer. There is no need to calibarate it
at driver level. If the chip is used as a joystick, calibaration can be
done using joystick device calibration mechanism.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement selftest feature as specified by chip manufacturer. Control:
read selftest sysfs entry
Response: "OK x y z" or "FAIL x y z"
where x, y, and z are difference between selftest mode and normal mode.
Test is passed when values are within acceptance limit values.
Acceptance limits are provided via platform data. See chip spesifications
for acceptance limits. If limits are not properly set, OK / FAIL decision
is meaningless. However, userspace application can still make decision
based on the numeric x, y, z values.
Selftest is meant for HW diagnostic purposes. It is not meant to be
called during normal use of the chip. It may cause false interrupt
events. Selftest mode delays polling of the normal results but it doesn't
cause wrong values. Chip must be in static state during selftest. Any
acceration during the test causes most probably failure.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
