As with most Pioneer devices, the device descriptor is vendor specific
and as such, the number of channels, the PCM format, endpoints and
sample rate need to be specified. This device has 8 inputs and 8 outputs
and a sample rate of 48000 only. The PCM format is S24_3LE like other
devices.
There seems to be an appetite for reducing duplication amongs these
Pioneer patches but again, I feel this is a step to be taken after
support has been added as it's not completely clear where the
commonalities are.
Signed-off-by: Olivia Mackintosh <livvy@base.nu>
Link: https://lore.kernel.org/r/20210202134225.3217-3-livvy@base.nu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the DJM-750, ensure that the format control message is passed to
the device when opening a stream. It seems as though fmt->sync_ep is not
always set when this function is called hence the passing of the value
at the call site. If this can be fixed, fmt->sync_up should be used as
the wvalue.
There doesn't seem to be a "cpu_to_le24" type function defined hence for
the open code but I did see a similar thing done in Bluez lib. Perhaps
we can get these definitions defined in byteorder.h. See hci_cpu_to_le24
in include/net/bluetooth/hci.h:2543 for similar usage.
Signed-off-by: Olivia Mackintosh <livvy@base.nu>
Link: https://lore.kernel.org/r/20210202134225.3217-2-livvy@base.nu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recently introduced sample rate validation code seems causing a
problem on some devices; namely, after performing this, the bus gets
screwed and it influences even on other USB devices.
As a quick workaround, perform it only for the necessary devices;
currently MOTU devices are known to need the valid altset checks, so
filter out other devices.
Fixes: 93db51d06b ("ALSA: usb-audio: Check valid altsetting at parsing rates for UAC2/3")
Reported-by: Jamie Heilman <jamie@audible.transient.net>
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1178203
Link: https://lore.kernel.org/r/20210123155842.22652-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At probing a UAC2/UAC3 device like NUX MG-300 USB interface, we get
error messages "RANGE setting not yet supported". It comes the place
where the driver tries to determine the resolution of mixer volumes
via SET_CUR_RES and GET_CUR_RES verbs. Those verbs aren't supported
on UAC2 and UAC3, hence the driver warns like the above. Although the
driver handles this error and works as expected, it's still ugly to
show such errors unnecessarily.
This patch papers over the errors by applying the resolution detection
only for UAC1 and skipping it for UAC2/UAC3.
Reported-by: Mike Oliphant <oliphant@nostatic.org>
Link: https://lore.kernel.org/r/20210120213932.1971-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current USB-audio driver gets an error at probing NUX MG-300 about
parsing the clocks. This is because the firmware doesn't return the
proper connection of the clock selector that is connected to a single
clock; it's likely that the firmware was lazy^w optimized and the
inquiry wasn't handled. Actually it makes little sense to inquire and
set up the single connection explicitly.
This patch fixes the issue by simply skipping the clock selector
inquiry if it's a single connection.
Reported-by: Mike Oliphant <oliphant@nostatic.org>
Link: https://lore.kernel.org/r/20210120213932.1971-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the recent refactoring, it's been reported that some USB-audio
devices (typically webcams) are no longer detected properly by
PulseAudio. The debug session revealed that it's failing at probing
by PA to try the sample rate 44.1kHz while the device has discrete
sample rates other than 44.1kHz. But the puzzle was that arecord
works as is, and some other devices with the discrete rates work,
either.
After all, this turned out to be the lack of the dependencies in a few
hw constraint rules: snd_pcm_hw_rule_add() has the (variable)
arguments specifying the dependent parameters, and some functions
didn't set the target parameter itself as the dependencies. This
resulted in an invalid parameter that could be generated only in a
certain call pattern. This bug itself has been present in the code,
but it didn't trigger errors just because the rules were casually
avoiding such a corner case. After the recent refactoring and
cleanup, however, the hw constraints work "as expected", and the
problem surfaced now.
For fixing the problem above, this patch adds the missing dependent
parameters to each snd_pcm_hw_rule() call.
Fixes: bc4e94aa8e ("ALSA: usb-audio: Handle discrete rates properly in hw constraints")
BugLink: http://bugzilla.opensuse.org/show_bug.cgi?id=1181014
Link: https://lore.kernel.org/r/20210120204554.30177-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds the Pioneer DJ DJM-750 to the quirks table and ensures
skip_pioneer_sync_ep() is (also) called: this device uses the vendor
ID of 0x08e4 (I'm not sure why they use multiple vendor IDs but many
just like to be awkward it seems).
Playback on all 8 channels works. I'll likely keep this working in the
future and submit futher patches and improvements as necessary.
Signed-off-by: Olivia Mackintosh <livvy@base.nu>
Link: https://lore.kernel.org/r/20210118130621.77miiie47wp7mump@base.nu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For addressing the regression on Pioneer devices, we recently
corrected the quirk code to enable the implicit feedback mode on those
devices properly. However, the devices still showed problems with the
full duplex operations with JACK, and after debug sessions, we figured
out that the older kernels that had worked with JACK also didn't use
the implicit feedback mode at all although they had the quirk code to
enable it; instead, the old code worked just to skip the normal sync
endpoint setup that would have been detected without it. IOW, what
broke without the implicit-fb quirk in the past was the application of
the normal sync endpoint that is actually the capture data endpoint on
these devices.
This patch covers the overseen piece: it modifies the quirk code again
not to enable the implicit feedback mode but just to make the driver
skipping the sync endpoint detection. This made the driver working
with JACK full-duplex mode again.
Still it's not quite clear why the implicit feedback doesn't work on
those devices yet; maybe it's about some issues in the URB setup. But
at least, with this patch, the driver should work in the level of the
older kernels again.
Fixes: 167c9dc84e ("ALSA: usb-audio: Fix implicit feedback sync setup for Pioneer devices")
Link: https://lore.kernel.org/r/20210118075816.25068-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The UAC2/3 sample rate setup is based on the clock node, which is
usually shared in the interface, and can't be re-setup without
deselecting the interface once, and that's how the current code
behaves. OTOH, the sample rate setup of UAC1 is per endpoint, hence
we basically need to call for each endpoint usage even if those share
the same interface.
This patch fixes the behavior of UAC1 to call always
snd_usb_init_sample_rate() in snd_usb_endpoint_configure().
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
Link: https://lore.kernel.org/r/20210118075816.25068-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current sample rate setup function for UAC1 assumes only the first
endpoint retrieved from the interface:altset pair, but the rate set up
may be needed also for the secondary endpoint. Also, retrieving the
endpoint number from the interface descriptor is redundant; we have
already the target endpoint in the given audioformat object.
This patch simplifies the code and corrects the target endpoint as
described in the above. It simply refers to fmt->endpoint directly.
Also, this patch drops the pioneer_djm_set_format_quirk() that is
caleld from snd_usb_set_format_quirk(); this function does the sample
rate setup but for the capture endpoint (0x82), and that's exactly
what the change above fixes.
Link: https://lore.kernel.org/r/20210118075816.25068-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The last remaining usage of strlcpy() in USB-audio driver is the setup
of the card longname string. Basically we need to know whether any
non-empty string is set or not, and no real length is needed.
Refactor the code and use strscpy() instead. After this change,
strlcpy() is gone from all sound/* code.
Link: https://lore.kernel.org/r/20210115100437.20906-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
USB-audio driver still contains two calls of strlcpy() because the
return size is evaluated. Basically it just checks whether the string
is copied or not, but since strcpy() may return a negative error code,
we should check the negative value and treat as filled.
Link: https://lore.kernel.org/r/20210115095758.19707-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the commit 5a6c3e11c9 ("ALSA: usb-audio: Add hw constraint for
implicit fb sync"), we apply the hw constraints for the implicit
feedback sync to make the secondary open aligned with the already
opened stream setup. This change assumed that the secondary open is
performed after the first stream has been already set up, and adds the
hw constraints to sync with the first stream's parameters only when
the EP setup for the first stream was confirmed at the open time.
However, most of applications handling the full-duplex operations do
open both playback and capture streams at first, then set up both
streams. This results in skipping the additional hw constraints since
the counter-part stream hasn't been set up yet at the open of the
second stream, and it eventually leads to "incompatible EP" error in
the end.
This patch corrects the behavior by always applying the hw constraints
for the implicit fb sync. The hw constraint rules are defined so that
they check the sync EP dynamically at each invocation, instead. This
covers the concurrent stream setups better and lets the hw refine
calls resolving to the right configuration.
Also this patch corrects a minor error that has existed in the debug
print that isn't built as default.
Fixes: 5a6c3e11c9 ("ALSA: usb-audio: Add hw constraint for implicit fb sync")
Link: https://lore.kernel.org/r/20210111081611.12790-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pioneer devices have both playback and capture streams sharing the
same iface/altsetting, and those need to be paired as implicit
feedback. Instead of a half-baked (and broken) static quirk entry,
set up more generically for those devices by checking the number of
endpoints and the attribute of the secondary EP.
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
Reported-by: František Kučera <konference@frantovo.cz>
Link: https://lore.kernel.org/r/20210108075219.21463-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are devices that have multiple endpoints sharing the same
iface/altset not only for sync but also for the actual streams, and
the audioformat for such an endpoint needs to be handled with the
proper endpoint index; otherwise it confuses the endpoint management.
This patch extends the audioformat to annotate the endpoint index, and
put the proper ep_idx=1 to Pioneer device quirk entries accordingly.
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
Link: https://lore.kernel.org/r/20210108075219.21463-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current endpoint handling assumed (more or less) a unique 1:1
relation between the endpoint and the iface/altset. The exception was
the sync EP without the implicit feedback which has usually the
secondary EP of the same altset. This works fine for most devices,
but it turned out that some unusual devices like Pinoeer's ones have
both playback and capture endpoints in the same iface/altsetting and
use both for the implicit feedback mode. For handling such a case, we
need to extend the endpoint management to take the shared interface
into account.
This patch does that: it adds a new object snd_usb_iface_ref for
managing the reference counts of the each USB interface that is used
by each endpoint. The interface setup is performed only once for the
(sharing) endpoints, and the doubly initialization is avoided.
Along with this, the resource release of endpoints and interface
refcounts are put into a single function, snd_usb_endpoint_free_all()
instead of looping in the caller side.
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
Link: https://lore.kernel.org/r/20210108075219.21463-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The implicit feedback mode needs to handle two endpoints and the
choice of the audioformat object for the sync EP is important since
this determines the compatibility of the hw_params. The current code
uses the same audioformat object if both the main EP and the sync EP
point to the same iface/altsetting. This was done in consideration of
the non-implicit-fb sync EP handling, and it doesn't match well with
the cases where actually to endpoints are defined in the sameiface /
altsetting like a few Pioneer devices.
Modify snd_usb_find_implicit_fb_sync_format() to pick up the
audioformat that is assigned in the counter-part substreams primarily,
so that the actual capture stream can be opened properly. We keep the
same audioformat object only as a fallback in case nothing found,
though.
Fixes: 9fddc15e80 ("ALSA: usb-audio: Factor out the implicit feedback quirk code")
Link: https://lore.kernel.org/r/20210108075219.21463-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent change in the endpoint management moved the endpoint object
creation from the stream open time to the parser of the audio
descriptor. It works fine for the standard audio, but it overlooked
the other places that create audio streams via quirks
(QUIRK_AUDIO_FIXED_ENDPOINT) like the reported a few Pioneer devices;
those call snd_usb_add_audio_stream() manually, hence they miss the
endpoints, eventually resulting in the error at opening streams.
Moreover, now the sync EP setup was moved to the explicit call of
snd_usb_audioformat_set_sync_ep(), and this needs to be added for
those places, too.
This patch addresses those regressions for quirks. It adds a local
helper function add_audio_stream_from_fixed_fmt(), which does the all
needed tasks, and replaces the calls of snd_usb_add_audio_stream()
with this new function.
Fixes: 54cb31901b ("ALSA: usb-audio: Create endpoint objects at parsing phase")
Reported-by: František Kučera <konference@frantovo.cz>
Link: https://lore.kernel.org/r/20210108075219.21463-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
strlcpy is deprecated. see: Documentation/process/deprecated.rst
Change the calls that do not use the strlcpy return value to the
preferred strscpy.
Done with cocci script:
@@
expression e1, e2, e3;
@@
- strlcpy(
+ strscpy(
e1, e2, e3);
This cocci script leaves the instances where the return value is
used unchanged.
After this patch, sound/ has 3 uses of strlcpy() that need to be
manually inspected for conversion and changed one day.
$ git grep -w strlcpy sound/
sound/usb/card.c: len = strlcpy(card->longname, s, sizeof(card->longname));
sound/usb/mixer.c: return strlcpy(buf, p->name, buflen);
sound/usb/mixer.c: return strlcpy(buf, p->names[index], buflen);
Miscellenea:
o Remove trailing whitespace in conversion of sound/core/hwdep.c
Link: https://lore.kernel.org/lkml/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/22b393d1790bb268769d0bab7bacf0866dcb0c14.camel@perches.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BOSS RC-505 (shown by lsusb as "Roland Corp. RC-505") does require the
same quirk as these other BOSS devices.
Without this quirk it is neither possible to capture audio from nor to
write audio to the RC-505. Both just result in an empty audio
stream. With these changes both capture and playback seem to work
quite fine. MIDI funtionality was not tested.
Tested-by: Harry Reinold <harry.reinold@posteo.de>
Signed-off-by: Timon Reinold <tirei@agon.one>
Link: https://lore.kernel.org/r/20210102210835.21268-1-tirei@agon.one
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BOSS AD-10 requires the very same quirk like other BOSS devices to
enable the special implicit feedback mode.
Reported-and-tested-by: Martin Passing <martin@passing.name>
Link: https://lore.kernel.org/r/20201229083428.20467-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use DIV_ROUND_UP() instead of open-coding it. This documents intent
and makes it more clear what is going on for the casual reviewer.
Generated using the following the Coccinelle semantic patch.
// <smpl>
@@
expression x, y;
@@
-(((x) + (y) - 1) / (y))
+DIV_ROUND_UP(x, y)
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20201223172229.781-11-lars@metafoo.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The calculation of in_cables and out_cables bitmaps are done with the
bit shift by the value from the descriptor, which is an arbitrary
value, and can lead to UBSAN shift-out-of-bounds warnings.
Fix it by filtering the bad descriptor values with the check of the
upper bound 0x10 (the cable bitmaps are 16 bits).
Reported-by: syzbot+92e45ae45543f89e8c88@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201223174557.10249-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The BOSS GT-1 (USB ID 0582:01d6) requires implicit feedback
like other similar BOSS devices. This patch adds this support.
[ rearranged the table entry in the ID order -- tiwai ]
Signed-off-by: Mike Oliphant <oliphant@nostatic.org>
Link: https://lore.kernel.org/r/20201221215533.2511-1-oliphant@nostatic.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some buggy firmware don't give the current sample rate but leaves
zero. Handle this case more gracefully without warning but just skip
the current rate verification from the next time.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201218145858.2357-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current channel-map control implementation in USB-audio driver may
lead to an error message like
"control 3:0:0:Playback Channel Map:0: access overflow"
when CONFIG_SND_CTL_VALIDATION is set. It's because the chmap get
callback clears the whole array no matter which count is set, and
rather the false-positive detection.
This patch fixes the problem by clearing only the needed array range
at usb_chmap_ctl_get().
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201211130048.6358-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Steinberg UR22 (with USB ID 0499:1509) requires the implicit feedback
for the proper playback, otherwise it causes occasional cracks.
This patch adds the corresponding the quirk table entry with the
recently added generic implicit fb support.
Reported-and-tested-by: Kilian <meschi@posteo.de>
Link: https://lore.kernel.org/r/20201209161835.13625-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yet another quirk for Pioneer DJ DDJ-SR2, which is quite similar like
other DJ DDJ models but with slightly different EPs or channels.
Reported-by: Geraldo <geraldogabriel@gmail.com>
Link: https://lore.kernel.org/r/20201130083714.10640-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch allows the Pioneer DJ DDJ-RR to be seen as a USB audio
device under Linux and therefore usable in such applications as
Mixxx.
Tested Master Audio out, headphones (both output jacks) and microphone
input. All work perfectly.
Signed-off-by: Daniel Martin <dmanlfc@gmail.com>
Link: https://lore.kernel.org/r/20201128084035.2958-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that the usb audio driver correctly finds implicit feedback endpoints,
the implicit feedback quirk for the MOTU M-Series is no longer required.
This also removes some unnecessary vendor specific messages from the MOTU
M-Series boot quirk. The removed vendor specific messages turned on vendor
specific interrupts to the host every 32 samples. The only thing the boot
quirk needs to do is wait for 2 seconds.
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Signed-off-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-42-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few other BOSS devices (BR-80, GT-100v2, Katana) seem requiring the
same quirk as BOSS GT-001, i.e. no implicit feedback for playback but
tying with capture. Add and correct the corresponding quirk table
entries for them.
Reported-and-tested-by: Keith Milner <kamilner@superlative.org>
Link: https://lore.kernel.org/r/20201123085347.19667-41-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A new module option, implicit_fb, is added to specify the driver
looking for the implicit feedback sync. This can be useful for a
device that could be working better in the implicit feed back mode and
user wants to test it quickly. When this works, we can add the quirk
entry easily.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-40-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch extends the implicit feedback mode parser code to check the
description more generically, so that the quirk entries can be added
without the explicit EP and interface numbers. The search is done for
the next and the previous interface of the given altset, and if both
entries are ASYNC mode and the direction matches, it just takes as the
sync endpoint. The generic parser is applicable only for the playback
stream.
As of now, only a few M-Audio devices have been converted to use this
mode.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-39-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The code dealing with the implicit feedback mode grew recently, and
it's becoming messy. As we receive more and more devices that need
the similar handling, it's better to be processed through a table
instead of the open code.
This patch moves the code that is relevant with parsing the implicit
feedback mode and some helpers into another file, implicit.c. The
detection and the setup of the implicit feedback sync EPs are
rewritten to use the ID/class matching table instead.
There should be no functional changes.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-38-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The capture stream of BOSS GT-001 seems always requiring to be tied
with the playback stream. OTOH, the playback stream of this device
doesn't seem working in the implicit fb mode, per se, since the
playback must be running before the capture stream.
This patch tries to address the points above:
- Avoid the implicit fb mode for the playback
- Set up a fake sync EP for the capture stream with the hard-coded
playback stream using the implicit fb mode
Reported-by: Keith Milner <kamilner@superlative.org>
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-37-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now the sync endpoints have been parsed at the beginning and won't be
changed dynamically, let's show them in the proc outputs for helping
debugging.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-36-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just for consistency, use unsigned char for iface and altsetting in
allover places. Also rearrange the field positions of
snd_usb_endpiont and tidy up with some comments.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-35-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Follow the inclusive terminology, just replace sync_master/sync_slave
with sync_source/sync_sink. It's also a bit clearer from its meaning,
too.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-34-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are multiple places in format.c performing the similar code for
setting the rate_min, rate_max and rates fields. This patch unifies
those in a helper function and calls it at the end of the parser phase
so that all rate_table entries have been already determined.
No functional changes, just a minor code refactoring.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-33-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are two places calculating the next packet size for the playback
stream in the exactly same way. Provide the single helper for this
purpose and use it from both places gracefully.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-32-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some fields like interface and alt_idx in snd_usb_substream are mostly
useless now as they can be referred via either cur_audiofmt or
data_endpoint assigned to the substream. Drop those, and also assure
the concurrency about the access of cur_audiofmt field.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-31-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Minor code refactoring to consolidate the URB deactivation code in
endpoint.c. A slight behavior change is that the error handling in
snd_usb_endpoint_start() leaves EP_FLAG_STOPPING now. This should be
synced with the later PCM sync_stop callback.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-30-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The endpoint objects may be started/stopped concurrently by different
substreams in the case of implicit feedback mode, while the current
code handles the reference counter without any protection.
This patch changes the refcount to atomic_t for avoiding the
inconsistency. We need no reference_t here as the refcount goes only
up to 2.
Also the name "use_count" is renamed to "running" since this is about
actually the running status, not the open refcount.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-29-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The audioformat is referred in many places but most of usages are
read-only. Let's add const prefix in the possible places.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-28-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The implicit feedback mode uses a ring buffer for storing the received
packet sizes from the feedback source, and the code has a slight flaw;
when a playback stream stalls by some reason and the URBs aren't
processed, the next_packet FIFO might become empty, but the driver
can't distinguish whether it's empty or full because it's managed with
read_poss and write_pos.
This patch addresses those by changing the next_packet array
management. Instead of keeping read and write positions, now the head
position and the queued amount are kept. It's easier to understand
about the emptiness. Also, the URB active flag is now cleared before
calling queue_pending_output_urbs() for avoiding (theoretically)
possible inconsistency.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-27-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is an intensive surgery for the endpoint and stream management
for achieving more robust and clean code.
The goals of this patch are:
- More clear endpoint resource changes
- The interface altsetting control in a single place
Below are brief description of the whole changes.
First off, most of the endpoint operations are moved into endpoint.c,
so that the snd_usb_endpoint object is only referred in other places.
The endpoint object is acquired and released via the new functions
snd_usb_endpoint_open() and snd_usb_endpoint_close() that are called
at PCM hw_params and hw_free callbacks, respectively. Those are
ref-counted and EPs can manage the multiple opens.
The open callback receives the audioformat and hw_params arguments,
and those are used for initializing the EP parameters; especially the
endpoint, interface and altset numbers are read from there, as well as
the PCM parameters like the format, rate and channels. Those are
stored in snd_usb_endpoint object. If it's the secondary open, the
function checks whether the given parameters are compatible with the
already opened EP setup, too.
The coupling with a sync EP (including an implicit feedback sync) is
done by the sole snd_usb_endpoint_set_sync() call.
The configuration of each endpoint is done in a single shot via
snd_usb_endpoint_configure() call. This is the place where most of
PCM configurations are done. A few flags and special handling in the
snd_usb_substream are dropped along with this change.
A significant difference wrt the configuration from the previous code
is the order of USB host interface setups. Now the interface is
always disabled at beginning and (re-)enabled at the last step of
snd_usb_endpoint_configure(), in order to be compliant with the
standard UAC2/3. For UAC1, the interface is set before the parameter
setups since there seem devices that require it (e.g. Yamaha THR10),
just like how it was done in the previous driver code.
The start/stop are almost same as before, also single-shots. The URB
callbacks need to be set via snd_usb_endpoint_set_callback() like the
previous code at the trigger phase, too.
Finally, the flag for the re-setup is set at the device suspend
through the full EP list, instead of PCM trigger. This catches the
overlooked cases where the PCM hasn't been running yet but the device
needs the full setup after resume.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-26-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function to evaluate the match of the parameters with an EP
assumes only the discrete rate tables and doesn't handle the
continuous rates properly.
This patch fixes match_endpoint_audioformats() to handle the
continuous rates. Also the almost useless debug prints there are
dropped.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-25-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 92adc96f8e ("ALSA: usb-audio: set the interface format
after resume on Dell WD19") introduced the workaround for the broken
setup after the resume specifically on a Dell dock model. However,
the full setup should have been performed after the resume on all
devices, as we can't guarantee the same state. So this patch removes
the conditional check and applies the workaround always.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-24-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The prepare_data_urb and retire_data_urb fields of the endpoint object
are set dynamically at PCM trigger start/stop. Those are evaluated in
the endpoint handler, but there can be a race, especially if two
different PCM substreams are handling the same endpoint for the
implicit feedback case. Also, the data_subs field of the endpoint is
set and accessed dynamically, too, which has the same risk.
As a slight improvement for the concurrency, this patch introduces the
function to set the callbacks and the data in a shot with the memory
barrier. In the reader side, it's also fetched with the memory
barrier.
There is still a room of race if prepare and retire callbacks are set
during executing the URB completion. But such an inconsistency may
happen only for the implicit fb source, i.e. it's only about the
capture stream. And luckily, the capture stream never sets the
prepare callback, hence the problem doesn't happen practically.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-23-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
start_endpoints() may leave the data endpoint running if an error
happens at starting the sync endpoint. We should stop both streams
properly, instead.
While we're at it, move the debug prints into the endpoint.c that is a
more suitable place.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-22-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A preliminary change for the later big changes. This is a minor code
refactoring to drop the unnecessary arguments that can be retrieved in
a different way.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-21-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A preliminary change for the later big changes. This is a minor code
refactoring to drop the unnecessary arguments that can be retrieved in
a different way.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-20-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A preliminary patch for the later big change. Just a minor code
refactoring.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-19-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Setting the active altsetting at changing sample rate seems
unrecommended. The host should deselect the altsetting at first
before that, then select it again.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-18-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a helper function to retrieve the usb_host_interface object from
the given interface and altsetting number pair, which is a commonly
used procedure in the driver code.
No functional changes, just minor code refactoring.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-17-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This behavior turned out to be invalid from the USB spec POV and
shouldn't be applied. As it's an optional flag that is set only via
an card control element that must be hardly used, let's drop it
again.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-16-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently snd_usb_endpoint objects are created at first when the
substream is opened and tries to assign the endpoints corresponding to
the matching audioformat. But since basically the all endpoints have
been already parsed and the information have been obtained, we may
create the endpoint objects statically at the init phase. It's easier
to manage for the implicit fb case, for example.
This patch changes the endpoint object management and lets the parser
to create the all endpoint objects.
This change shouldn't bring any functional changes.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-15-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The implicit feedback mode initializes both the main data stream and
the sync data stream. When a sync stream was already opened, this
would result in the doubly initialization and might screw up things.
Add the check of already opened sync streams and skip the unnecessary
initialization.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-14-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The file debug.h contains a simple macro for debug prints, and it's
used only in two places, the format parser and the hw_params rules.
The former actually should print a more informative message instead,
so the only users are the hw_parmas rules.
This patch moves the contents of debug.h into the hw_params rules
local code and remove the unneeded includes. Also, the debug print in
the format parser is replaced with the information print with more
useful information, and the raw printk() call is replaced with
pr_debug().
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-13-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Several hw_params functions narrows the interval via min/max rule in
the very similar way, so factor out those into a helper function and
use commonly.
No functional changes, just minor code refactoring.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-12-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current code, there is no check at the stream open time whether
the endpoint is being already used by others. In the normal
operations, this shouldn't happen, but in the case of the implicit
feedback mode, it's a common problem with the full duplex operation,
because the capture stream is always opened by the playback stream as
an implicit sync source.
Although we recently introduced the check of such a conflict of
parameters at the PCM hw_params time, it doesn't give any hint at the
hw_params itself and just gives the error. This isn't quite
comfortable, and it caused problems on many applications.
This patch attempts to make the parameter handling easier by
introducing the strict hw constraint matching with the counterpart
stream that is being used. That said, when an implicit feedback
playback stream is running before a capture stream is opened, the
capture stream carries the PCM hw-constraint to allow only the same
sample rate, format, periods and period frames as the running playback
stream. If not opened or there is no conflict of endpoints, the
behavior remains as same as before.
Note that this kind of "weak link" should work for most cases, but
this is no concrete solution; e.g. if an application changes the hw
params multiple times while another stream is opened, this would lead
to inconsistencies.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-11-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a preliminary work for the upcoming hw-constraint change for
the implicit feedback mode.
Currently snd_usb_autoresume() is called at the end of
setup_hwinfo(). It's a bit confusing; because of this implicit
refcount usage, the caller side needs to call snd_usb_autosuspend()
later in the error path although it's not seen inside the function.
Instead, it's clearer to call both snd_usb_autoresume() and suspend()
in the very same function.
It's only refactoring and no functional changes.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of parsing and evaluating the sync endpoint and the implicit
feedback mode at each time the audio stream is opened, let's parse it
once at the probe time, as the all needed information can be obtained
statically from the descriptor or from the quirk.
This patch extends audioformat struct to record the sync endpoint,
interface and altsetting as well as the implicit feedback flag, which
are filled at parsing the streams. Then, set_sync_endpoint() is much
simplified just to follow the already parsed data.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-9-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are a few rooms for improvements wrt the debug prints:
- The EP debug print is shown only at starting, not at stopping
- The EP debug print contains useless object addresses
- Some helpers show the urb and the EP object addresses, too
This patch addresses those shortcomings.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The sync EP setup isn't cleared at stopping the stream but expected to
be cleared at the next stream start. This may leave the sync link
setup stale and can spoof wrongly when full duplex streams were
running in the implicit fb sync. Let's initialize them properly at
start and end of the stream.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-7-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Factor out the code to obtain snd_usb_endpoint object matching with
the given endpoint. It'll be used in the later patch to add the
implicit feedback hw-constraint.
No functional change by this patch itself.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It seems that many UAC2 devices are with the implicit feedback, but
they couldn't be probed properly because the assumption the driver
takes currently isn't applied: they have the single endpoint for both
data and implicit-fb streams, while we checked only the classical sync
endpoints assigned to the next altsetting in the same interface.
This patch extends the search to match with those typical cases where
the implicit fb stream is found in the next interface number.
While we're at it, slightly refactor the code, not returning 0/-ERROR
but use the standard bool to success/failur, which is more intuitive
in this particular case.
Reported-by: Dylan Robinson <dylan_robinson@motu.com>
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current driver code assumes blindly that all found sample rates for
the same endpoint from the UAC2 and UAC3 descriptors can be used no
matter which altsetting, but actually this was wrong: some devices
accept only limited sample rates in each altsetting. For determining
which altsetting supports which rate, we need to verify each sample rate
and check the validity via UAC2_AS_VAL_ALT_SETTINGS. This control
reports back the available altsettings as a bitmap.
This patch implements the missing piece above, the verification and
reconstructs the sample rate tables based on the result.
An open question is how to deal with the altsettings that ended up
with no valid sample rates after verification. At least, there is a
device that showed this problem although the sample rates did work in
the later usage (see bug link). For now, we accept such an altset as
is, assuming that it's a firmware bug.
Reported-by: Dylan Robinson <dylan_robinson@motu.com>
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1178203
Link: https://lore.kernel.org/r/20201123085347.19667-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM trigger callback is atomic, hence we must not call a function
like usb_set_interface() there. Calling it from there would lead to a
kernel Oops.
Fix it by moving the usb_set_interface() call to set_sync_endpoint().
Also, apply the snd_usb_set_interface_quirk() for consistency, too.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current code, when the device provides the discrete sample rate
tables with unusual sample rates, the driver tries to gather the whole
values from the audioformat entries and create a hw-constraint rule to
restrict with this single rate list. This is rather inefficient and
may overlook the rates that are associated only with the certain
audioformat entries.
This patch improves the hw constraint setup by rewriting the existing
hw_rule_rate(). The discrete sample rates (identified by rate_table
and nr_rates of format entry) are checked in the existing
hw_rule_rate() instead of extra rules; in the case of discrete rates,
the function compares with each rate table entry and calculates the
min/max values from there. For the contiguous rates, the behavior
doesn't change.
Along with it, snd_usb_pcm_check_knot() and snb_usb_substream
rate_list field become superfluous, thus those are dropped.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Found one more Logitech device, BCC950 ConferenceCam, which needs
the same delay here. This makes 3 out of 3 devices I have tried.
Therefore, add a delay for all Logitech devices as it does not hurt.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: <stable@vger.kernel.org> # 4.19.y, 5.4.y
Link: https://lore.kernel.org/r/20201117122803.24310-1-joakim.tjernlund@infinera.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes audio distortion on playback for the Allen&Heath
Qu-16.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201104115717.GA19046@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes audio distortion on playback for the Yamaha MODX.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Tested-by: Frank Slotta <frank.slotta@posteo.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201104120705.GA19126@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Khadas audio devices ( USB_ID_VENDOR 0x3353 )
have DSD-capable implementations from XMOS
need add new usb vendor id for recognition
Signed-off-by: Artem Lapkin <art@khadas.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201103103311.5435-1-art@khadas.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Zoom UAC-2 USB audio interface provides an async playback endpoint
("1 OUT (ASYNC)") and capture endpoint ("2 IN (ASYNC)"), both with
2-channel S32_LE in 44.1, 48, 88.2, 96, 176.4, or 192
kilosamples/s. The device provides explicit feedback to adjust the
host's playback rate, but the feedback appears unstable and biased
relative to the device's capture rate.
"alsaloop -t 1000" experiences playback underruns and tries to
resample the captured audio to match the varying playback
rate. Forcing the kernel to use implicit feedback appears to
produce more stable results. This causes the host to transmit one
playback sample for each capture sample received. (Zoom North America
has been notified of this change.)
Signed-off-by: Keith Winstein <keithw@cs.stanford.edu>
Tested-by: Keith Winstein <keithw@cs.stanford.edu>
Cc: <stable@vger.kernel.org>
BugLink: https://lore.kernel.org/r/20201027071841.GA164525@trolley.csail.mit.edu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just a few additional small and trivial fixes.
-----BEGIN PGP SIGNATURE-----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=sYVq
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few additional small and trivial fixes"
* tag 'sound-fix-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix the return value if cb func is already registered
ALSA: usb-audio: Line6 Pod Go interface requires static clock rate quirk
ALSA: hda/ca0132: make some const arrays static, makes object smaller
ALSA: sparc: dbri: fix repeated word 'the'
Recently released Line6 Pod Go requires static clock rate quirk to make
its usb audio interface working. Added its usb id to the list of similar
line6 devices.
Signed-off-by: Lukasz Halman <lukasz.halman@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201020061409.GA24382@TAG009442538903
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The amount of changes is smaller at this round (what a surprise),
but lots of activity is seen. Most of changes are about ASoC
driver development, especially Intel platforms.
Here are some highlights:
General:
* Replace all tasklet usages with other alternatives
* Cleanup of the ASoC error unwinding code
* Fixes for trivial issues caught by static checker
* Spell fixes allover the places
ALSA Core:
* Lockdep fix for control devices
* Fix for potential OSS sequencer mutex stalls
HD-audio and USB-audio:
* SoundBlaster AE-7 support
* Changes in quirk table for the rename handling
* Quirks for HP and ASUS machines, Pioneer DJ DJM-250MK2.
ASoC:
* Lots of updates for Intel SOF and SoundWire enablement
* Replacement of the DSP driver for some older x86 systems;
the new code was written from scratch, better maintenance
expected
* Helpers for parsing auxiluary devices from the device tree
* New support for AllWinner A64, Cirrus Logic CS4234, Mediatek
MT6359 Microchip S/PDIF TX and RX controllers, Realtek RT1015P,
and Texas Instruments J721E, TAS2110, TAS2564 and TAS2764
-----BEGIN PGP SIGNATURE-----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=nWAp
-----END PGP SIGNATURE-----
Merge tag 'sound-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"The amount of changes is smaller at this round (what a surprise), but
lots of activity is seen. Most of changes are about ASoC driver
development, especially Intel platforms. Here are some highlights:
General:
- Replace all tasklet usages with other alternatives
- Cleanup of the ASoC error unwinding code
- Fixes for trivial issues caught by static checker
- Spell fixes allover the places
ALSA Core:
- Lockdep fix for control devices
- Fix for potential OSS sequencer mutex stalls
HD-audio and USB-audio:
- SoundBlaster AE-7 support
- Changes in quirk table for the rename handling
- Quirks for HP and ASUS machines, Pioneer DJ DJM-250MK2.
ASoC:
- Lots of updates for Intel SOF and SoundWire enablement
- Replacement of the DSP driver for some older x86 systems; the new
code was written from scratch, better maintenance expected
- Helpers for parsing auxiluary devices from the device tree
- New support for AllWinner A64, Cirrus Logic CS4234, Mediatek MT6359
Microchip S/PDIF TX and RX controllers, Realtek RT1015P, and Texas
Instruments J721E, TAS2110, TAS2564 and TAS2764"
* tag 'sound-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (498 commits)
ALSA: hda/hdmi: fix incorrect locking in hdmi_pcm_close
ALSA: hda: fix jack detection with Realtek codecs when in D3
ALSA: fireworks: use semicolons rather than commas to separate statements
ALSA: hda: use semicolons rather than commas to separate statements
ALSA: hda/i915 - fix list corruption with concurrent probes
ASoC: dmaengine: Document support for TX only or RX only streams
ASoC: mchp-spdiftx: remove 'TX' from playback stream name
ASoC: ti: davinci-mcasp: Use &pdev->dev for early dev_warn
ASoC: tas2764: Add the driver for the TAS2764
dt-bindings: tas2764: Add the TAS2764 binding doc
ASoC: Intel: catpt: Add explicit DMADEVICES kconfig dependency
ASoC: Intel: catpt: Fix compilation when CONFIG_MODULES is disabled
ASoC: stm32: dfsdm: add actual resolution trace
ASoC: stm32: dfsdm: change rate limits
ASoC: qcom: sc7180: Add support for audio over DP
Asoc: qcom: lpass-platform : Increase buffer size
ASoC: qcom: Add support for lpass hdmi driver
Asoc: qcom: lpass:Update lpaif_dmactl members order
Asoc:qcom:lpass-cpu:Update dts property read API
ASoC: dt-bindings: Add dt binding for lpass hdmi
...
The usb_control_msg_send() and usb_control_msg_recv() calls can return
an error if a "short" write/read happens, and they can handle data off
of the stack, so move the driver over to using those calls instead,
saving some logic when dynamically allocating memory.
v2: API change of use usb_control_msg_send() and usb_control_msg_recv()
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200914153756.3412156-9-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200923134348.23862-13-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_control_msg_send() and usb_control_msg_recv() calls can return
an error if a "short" write/read happens, so move the driver over to
using those calls instead, saving some logic in the wrapper functions
that were being used in this driver.
This also resolves a long-staging bug where data on the stack was being
sent in a USB control message, which was not allowed.
v2: API change of usb_control_msg_send()
Cc: Jaroslav Kysela <perex@perex.cz>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200914153756.3412156-8-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200923134348.23862-11-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_control_msg_send() call can handle data on the stack, as well as
returning an error if a "short" write happens, so move the driver over
to using that call instead. This ends up removing a helper function
that is no longer needed.
v2: API change in usb_control_msg_send()
Cc: Jaroslav Kysela <perex@perex.cz>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200914153756.3412156-7-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200923134348.23862-10-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch extends support for DJM-250MK2 and allows mapping
playback and capture channels to available sources.
Configures the card through USB commands.
Signed-off-by: František Kučera <franta-linux@frantovo.cz>
Link: https://lore.kernel.org/r/20200922144206.10472-1-konference@frantovo.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 34dedd2a83.
According to Realtek, volume FU works for line-in.
I can confirm volume control works after device firmware is updated.
Fixes: 34dedd2a83 ("ALSA: usb-audio: Disable Lenovo P620 Rear line-in volume control")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20200915103925.12777-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
