Keep track for which BO a resource was allocated.
This is necessary to move the LRU handling into the resources.
A bit problematic is i915 since it tries to use the resource
interface without a BO which is illegal from the conceptional
point of view.
v2: Document that this is a weak reference and add a workaround for i915
v3: further document that this is protected by ttm_device::lru_lock and
clarify the i915 workaround
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124122514.1832-4-christian.koenig@amd.com
In nvkm_acr_hsfw_load_bl(), the return value of kmalloc() is directly
passed to memcpy(), which could lead to undefined behavior on failure
of kmalloc().
Fix this bug by using kmemdup() instead of kmalloc()+memcpy().
This bug was found by a static analyzer.
Builds with 'make allyesconfig' show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 22dcda45a3 ("drm/nouveau/acr: implement new subdev to replace "secure boot"")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124165856.57022-1-zhou1615@umn.edu
The current CSC setup code for the BCM2711 uses a sequence of register
writes to configure the CSC depending on whether we output using a full
or limited range.
However, with the upcoming introduction of the YUV output, we're going
to add new matrices to perform the conversions, so we should switch to
something a bit more flexible that takes the matrix as an argument and
programs the CSC accordingly.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-10-maxime@cerno.tech
The CSC callbacks takes a boolean as an argument to tell whether we're
using the full range or limited range RGB.
However, with the upcoming YUV support, the logic will be a bit more
complex. In order to address this, let's make the callbacks take the
entire mode, and call our new helper to tell whether the full or limited
range RGB should be used.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-7-maxime@cerno.tech
The current code assumes that the RGB444 and YUV444 formats are the
same, but the HDMI 2.0 specification states that:
The three DC_XXbit bits above only indicate support for RGB 4:4:4 at
that pixel size. Support for YCBCR 4:4:4 in Deep Color modes is
indicated with the DC_Y444 bit. If DC_Y444 is set, then YCBCR 4:4:4
is supported for all modes indicated by the DC_XXbit flags.
So if we have YUV444 support and any DC_XXbit flag set but the DC_Y444
flag isn't, we'll assume that we support that deep colour mode for
YUV444 which breaks the specification.
In order to fix this, let's split the edid_hdmi_dc_modes field in struct
drm_display_info into two fields, one for RGB444 and one for YUV444.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: d0c94692e0 ("drm/edid: Parse and handle HDMI deep color modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-4-maxime@cerno.tech
The current code, when parsing the EDID Deep Color depths, that the
YUV422 cannot be used, referring to the HDMI 1.3 Specification.
This specification, in its section 6.2.4, indeed states:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is not permitted for any Deep Color mode.
This indeed can be interpreted like the code does, but the HDMI 1.4
specification further clarifies that statement in its section 6.2.4:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is also 36-bit mode but does not require the further use
of the Deep Color modes described in section 6.5.2 and 6.5.3.
This means that, even though YUV422 can be used with 12 bit per color,
it shouldn't be treated as a deep color mode.
This is also broken with YUV444 if it's supported by the display, but
DRM_EDID_HDMI_DC_Y444 isn't set. In such a case, the code will clear
color_formats of the YUV444 support set previously in
drm_parse_cea_ext(), but will not set it back.
Since the formats supported are already setup properly in
drm_parse_cea_ext(), let's just remove the code modifying the formats in
drm_parse_hdmi_deep_color_info()
Fixes: d0c94692e0 ("drm/edid: Parse and handle HDMI deep color modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-3-maxime@cerno.tech
The drm_hdmi_avi_infoframe_colorspace() function actually sets the
colorimetry and extended_colorimetry fields in the hdmi_avi_infoframe
structure with DRM_MODE_COLORIMETRY_* values.
To make things worse, the hdmi_avi_infoframe structure also has a
colorspace field used to signal whether an RGB or YUV output is being
used.
Let's remove the inconsistency and allow for the colorspace usage by
renaming the function.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-2-maxime@cerno.tech
On some servers with MGA G200_SE_A (rev 42), booting with Legacy BIOS,
the hardware hangs when using kdump and kexec into the kdump kernel.
This happens when the uncompress code tries to write "Decompressing Linux"
to the VGA Console.
It can be reproduced by writing to the VGA console (0xB8000) after
booting to graphic mode, it generates the following error:
kernel:NMI: PCI system error (SERR) for reason a0 on CPU 0.
kernel:Dazed and confused, but trying to continue
The root cause is the configuration of the MGA GCTL6 register
According to the GCTL6 register documentation:
bit 0 is gcgrmode:
0: Enables alpha mode, and the character generator addressing system is
activated.
1: Enables graphics mode, and the character addressing system is not
used.
bit 1 is chainodd even:
0: The A0 signal of the memory address bus is used during system memory
addressing.
1: Allows A0 to be replaced by either the A16 signal of the system
address (ifmemmapsl is ‘00’), or by the hpgoddev (MISC<5>, odd/even
page select) field, described on page 3-294).
bit 3-2 are memmapsl:
Memory map select bits 1 and 0. VGA.
These bits select where the video memory is mapped, as shown below:
00 => A0000h - BFFFFh
01 => A0000h - AFFFFh
10 => B0000h - B7FFFh
11 => B8000h - BFFFFh
bit 7-4 are reserved.
Current code set it to 0x05 => memmapsl to b01 => 0xa0000 (graphic mode)
But on x86, the VGA console is at 0xb8000 (text mode)
In arch/x86/boot/compressed/misc.c debug strings are written to 0xb8000
As the driver doesn't use this mapping at 0xa0000, it is safe to set it to
0xb8000 instead, to avoid kernel hang on G200_SE_A rev42, with kexec/kdump.
Thus changing the value 0x05 to 0x0d
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220119102905.1194787-1-jfalempe@redhat.com
Move the base i915 buddy allocator code into drm
- Move i915_buddy.h to include/drm
- Move i915_buddy.c to drm root folder
- Rename "i915" string with "drm" string wherever applicable
- Rename "I915" string with "DRM" string wherever applicable
- Fix header file dependencies
- Fix alignment issues
- add Makefile support for drm buddy
- export functions and write kerneldoc description
- Remove i915 selftest config check condition as buddy selftest
will be moved to drm selftest folder
cleanup i915 buddy references in i915 driver module
and replace with drm buddy
v2:
- include header file in alphabetical order(Thomas)
- merged changes listed in the body section into a single patch
to keep the build intact(Christian, Jani)
v3:
- make drm buddy a separate module(Thomas, Christian)
v4:
- Fix build error reported by kernel test robot <lkp@intel.com>
- removed i915 buddy selftest from i915_mock_selftests.h to
avoid build error
- removed selftests/i915_buddy.c file as we create a new set of
buddy test cases in drm/selftests folder
v5:
- Fix merge conflict issue
v6:
- replace drm_buddy_mm structure name as drm_buddy(Thomas, Christian)
- replace drm_buddy_alloc() function name as drm_buddy_alloc_blocks()
(Thomas)
- replace drm_buddy_free() function name as drm_buddy_free_block()
(Thomas)
- export drm_buddy_free_block() function
- fix multiple instances of KMEM_CACHE() entry
v7:
- fix warnings reported by kernel test robot <lkp@intel.com>
- modify the license(Christian)
v8:
- fix warnings reported by kernel test robot <lkp@intel.com>
Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220118104504.2349-1-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>
It will connect to the mipi dsi host and find the corresponding
mipi dsi host node, but the node registered by the mipi dsi host
has not been loaded yet. of_find_mipi_dsi_host_by_node() returns -EINVAL
which causes the calling driver to fail.
If the anx7625 driver is loaded afterwards the driver requesting
the mipi dsi host will not notice this.
Better approach is to return -EPROBE_DEFER in such case.
Then when the anx7625 driver appears the driver requesting
the mipi dsi host will be probed again.
Signed-off-by: owen <qwt9588@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220117100949.9542-1-qwt9588@gamil.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Move DisplayPort functions into a separate module to reduce the size
of the KMS helpers. Select DRM_DP_HELPER for all users of the code. To
avoid naming conflicts, rename drm_dp_helper.c to drm_dp.c
This change can help to reduce the size of the kernel binary. Some
numbers from a x86-64 test build:
Before:
drm_kms_helper.ko: 447480 bytes
After:
drm_dp_helper.ko: 216632 bytes
drm_kms_helper.ko: 239424 bytes
For early-boot graphics, generic DRM drivers, such as simpledrm,
require DRM KMS helpers to be built into the kernel. Generic helper
functions for DisplayPort take up a significant portion of DRM KMS
helper library. These functions are not used by generic drivers and
can be loaded as a module.
v3:
* fix include statement in DRM selftests
v2:
* move DP helper code into dp/ (Jani)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220114114535.29157-4-tzimmermann@suse.de
On a dual core group GPUs (such as T628) fragment shading can be
performed over all cores (because a fragment shader job doesn't
need coherency between threads), however vertex shading requires
to be run on the same core group as the tiler (which always lives
in core group 0).
As a first step to support T628 power on only the first core group
(so no jobs are scheduled on the second one). This makes T628 look
like every other Midgard GPU (and throws away up to half the cores).
With this patch panfrost is able to drive T628 (r1p0) GPU on some
armv8 SoCs (in particular BE-M1000). Without the patch rendering
is horribly broken (desktop is completely unusable) and eventually
the GPU locks up (it takes from a few seconds to a couple of
minutes).
Using the second core group requires support in Mesa (and an UABI
change): the userspace should
1) set PANFROST_JD_DOESNT_NEED_COHERENCY_ON_GPU flag to opt-in
to allowing the job to run across all cores.
2) set PANFROST_RUN_ON_SECOND_CORE_GROUP flag to allow compute
jobs to be run on the second core group (at the moment Mesa
does not advertise compute support on anything older than
Mali T760)
But there's little point adding such flags until someone (myself)
steps up to do the Mesa work.
Signed-off-by: Alexey Sheplyakov <asheplyakov@basealt.ru>
Signed-off-by: Vadim V. Vlasov <vadim.vlasov@elpitech.ru>
Tested-by: Alexey Sheplyakov <asheplyakov@basealt.ru>
Co-developed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220115160658.582646-1-asheplyakov@basealt.ru
