Sigh. Undo some earlier changes to mv_port_intr(),
so that we now read/clear SError again in all cases.
Arrange the top of the function to be as close as possible
to what we need for a later update (in this series) for ERR_DEV handling.
Fix things so that libata-eh can attempt a READ_LOG_EXT_10H
in response to a failed NCQ command, by just doing a local
mv_eh_freeze() rather than ata_port_freeze().
This will now fully handle NCQ errors much of the time,
but more fixes are needed for FBS/PMP, and for certain chip errata.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rearrange mv_config_fbs() to more closely follow the (corrected) datasheet
recommendations for NCQ and FIS-based switching (FBS).
Also, maintain a port flag to let us know when FBS is enabled.
We will make more use of that flag later in this patch series.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part 1 of workaround for errata "sata#25" for the 60x1 series
(the second half of this errata workaround is still in development.
Bit22 of the GPIO port has to be set "on" when in NCQ mode.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The EDMA engine cannot tolerate a mix of NCQ/non-NCQ commands,
and cannot be used for PIO at all. So we need to prevent libata
from trying to feed us such mixtures.
Introduce mv_qc_defer() for this purpose, and use it for all chip versions.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When performing EH, it is recommended to wait for the EDMA engine
to empty out requests-in-progress before disabling EDMA.
Introduce code to poll the EDMA_STATUS register for idle/empty bits
before disabling EDMA. For non-EH operation, this will normally exit
without delay, other than the register read.
A later series of patches may focus on eliminating this and various
other register reads (when possible) throughout the driver,
but for now we're focussing on solid reliablity.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some of the GenIIe EDMA optimizations should not be used
for non-PCI (SOC) devices, and nor for certain configurations
of conventional PCI (non PCI-X, PCIe) buses.
Logic taken/simplified from that in the Marvell proprietary driver.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
More cosmetic changes; no code changes.
-- try and improve consistency of naming.
-- add missing _OFS to tails of register offset definitions.
-- rename mv_setup_ifctl() to mv_setup_ifcfg(), since that's what it really does.
-- remove/move some dead comments
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On certain configurations (certain macbooks), even though all the
conditions for SIDPR access described in the datasheet are met,
actually reading those registers just returns 0 and have no effect on
write. Verify SIDPR is actually working before enabling it.
This is reported by Ryan Roth in bz#10512.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ryan Roth <ryan.roth@ch2m.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some controllers (jmb and inic162x) use 0x77 and 0x7f to indicate that
the device isn't ready yet. It looks like they use 0xff if device
presence is detected but connection isn't established. 0x77 or 0x7f
after connection is established and use the value from signature FIS
after receiving it.
This patch implements ata_check_ready(), which takes TF status value
and determines whether the port is ready or not considering the above
and other conditions, and use it in @check_ready() functions. This is
safe as both 0x77 and 0x7f aren't valid ready status value even though
they have BSY bit cleared.
This fixes hot plug detection failures which can be triggered with
certain drives if they aren't already spun up when the data connector
is hot plugged.
Tested on sil, sil24, ahci (jmb/ich), piix and inic162x combined with
eight drives from all major vendors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net_cls_act: act_simple dont ignore realloc code
iwlwifi: make IWLWIFI a tristate
Revert "atm: Do not free already unregistered net device."
dccp: return -EINVAL on invalid feature length
irda: fix !PNP support for drivers/net/irda/smsc-ircc2.c
irda: fix !PNP support in drivers/net/irda/nsc-ircc.c
net_cls_act: Make act_simple use of netlink policy.
ip: Use inline function dst_metric() instead of direct access to dst->metric[]
ip: Make use of the inline function dst_metric_locked()
atm: Bad locking on br2684_devs modifications.
atm: Do not free already unregistered net device.
mac80211: Do not free net device after it is unregistered.
bridge: Consolidate error paths in br_add_bridge().
bridge: Net device leak in br_add_bridge().
niu: Fix probing regression for maramba on-board chips.
lapbeth: Release ->ethdev when unregistering device.
xfrm: convert empty xfrm_audit_* macros to functions
net: Fix useless comment reference loop.
sch_htb: remove from event queue in htb_parent_to_leaf()
IWLWIFI should be a tristate so that if IWLCORE and/or IWL3945 are m
and none of them is y kbuild doesn't create an empty
drivers/net/wireless/built-in.o
This patch also removes the pointless "default n".
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Support creation of FMRs with pages smaller than 4K
IB/ehca: Fix function return types
RDMA/cxgb3: Bump up the MPA connection setup timeout.
RDMA/cxgb3: Silently ignore close reply after abort.
RDMA/cxgb3: QP flush fixes
IB/ipoib: Fix transmit queue stalling forever
IB/mlx4: Fix off-by-one errors in calls to mlx4_ib_free_cq_buf()
Don't hard code a test against a minimum page shift of 12, since the
device may support smaller pages. Test against the actual smallest
page size from the device capabilities.
Signed-off-by: Oren Duer <oren@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Also remove duplicate assignment of local_ca_ack_delay and change
min_t check for local_ca_ack_delay to u8 instead of int.
Signed-off-by: Stefan Roscher <stefan.roscher at de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 06916639e2 ("driver-core: add
dev_name() to help transition away from using bus_id") added a static
inline dev_name() and used it in dev_printk.
Unfortunately, drivers/edac/edac_core.h defines a macro called
dev_name(). Rename the latter.
Diagnosis by Tony Breeds and Michael Ellerman.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86 PCI: call dmi_check_pciprobe()
x86/pci: add pci=skip_isa_align command lines.
x86/pci: remove flag in pci_cfg_space_size_ext
x86: fix section mismatch in pci_scan_bus
The new mac_esp scsi driver needs CONFIG_SCSI_SPI_ATTRS, just like all other
drivers using the new esp_scsi core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/input/serio/hp_sdc.c: In function 'hp_sdc_take':
drivers/input/serio/hp_sdc.c:198: error: implicit declaration of function 'up'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The single step test is not terribly costly and it should be able to
pass at 1000 loops successfully in under 1 second. A non-kgdb timing
regression was found using this test, but it did not occur frequently
because by default the test was only executed a single time.
This patch changes the default for the single step test to 1000
iterations and allows for individual configuration of the single step
test to further exercise the kgdb subsystem when needed.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Shadowed variable and integer as NULL pointer fixes:
drivers/misc/kgdbts.c:877:6: warning: symbol 'sys_open_test' shadows an earlier one
drivers/misc/kgdbts.c:537:27: originally declared here
drivers/misc/kgdbts.c:378:22: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:386:22: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:468:30: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:472:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:502:30: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:506:30: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:509:30: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:523:20: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:527:20: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:530:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:541:21: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:545:21: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:548:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:559:30: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:563:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:573:16: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:574:19: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:578:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:588:16: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:589:19: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:593:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:602:16: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:604:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:925:3: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:938:3: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
x86.git testing found this build bug on v2.6.26-rc1:
ERROR: "pnp_get_resource" [drivers/net/irda/smsc-ircc2.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
the driver did not anticipate the case of !CONFIG_PNP which is rare but
still possible. Instead of restricting the driver to PNP-only in the
Kconfig space, add the (trivial) dummy struct pnp_driver - this is that
other drivers use in the !PNP case too.
The driver itself can in theory be initialized on !PNP too in certain
cases, via smsc_ircc_legacy_probe().
Patch only minimally build tested, i dont have this hardware.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
x86.git testing found the following build failure in latest -git:
drivers/built-in.o: In function `nsc_ircc_pnp_probe':
nsc-ircc.c:(.text+0xdf1b6): undefined reference to `pnp_get_resource'
nsc-ircc.c:(.text+0xdf1d4): undefined reference to `pnp_get_resource'
nsc-ircc.c:(.text+0xdf1ee): undefined reference to `pnp_get_resource'
nsc-ircc.c:(.text+0xdf237): undefined reference to `pnp_get_resource'
nsc-ircc.c:(.text+0xdf24c): undefined reference to `pnp_get_resource'
drivers/built-in.o:nsc-ircc.c:(.text+0xdf266): more undefined references to `pnp_get_resource' follow
make: *** [.tmp_vmlinux1] Error 1
triggered via this config:
http://redhat.com/~mingo/misc/config-Sat_May__3_20_53_13_CEST_2008.bad
while generally most users will have PNP enabled, drivers can support
non-PNP build mode too - and most drivers implement it. That is typically
done by providing a dummy pnp_driver structure that will not probe anything.
The fallback routines in the driver will handle this dumber mode of
operation too.
This patch implements that. I have not tested whether this actually
works on real hardware so take care. It does resolve the build bug.
[ Another solution that is used by a few drivers is to exclude the driver
in the Kconfig if PNP is disabled, via "depends on PNP", but this would
limit the availability of the driver needlessly. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the variable name 'dev_name' in the top-level namespace is a bad
idea.
This conflicts with linux/device.h's inline function of the same name.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch re-ordering could be harmful:
commit 1fd1890594
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Sat Apr 26 22:25:24 2008 +0200
ide: add IDE_HFLAG_SERIALIZE_DMA host flag
...
is buggy because ->init_dma method / ide_hwif_setup_dma() is called
before IDE_HFLAG_SERIALIZE_DMA host flag is checked.
Fix it by checking IDE_HFLAG_SERIALIZE[_DMA] after DMA initialization.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This fixes some two minor clk issues.
The first is a comparison where a byte will probably wrap around to 0 instead of being saturated to 255, shouldn't be triggered very often but need fixing.
The second is an attempt by the driver to adjust MCLK down to the maximum frequency according to the spec, so we don't accidentally overclock the PL18x block. None of the mach-{versatile|integrator|lh7a40x} that use it in-tree seem to have a problem with this (all are well below 100MHz, typically 33MHz), but some day there will be a problem.
This is not applied on top of the earlier mmci patch for race condition but rather a clean 2.6.25, but I guess it applies without major protests anyway.
Signed-off-by: Linus Walleij <triad@df.lth.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Changeset 7f7c4072ea ("niu: Determine
the # of ports from the card's VPD data") caused maramba on-board
NIU ports to stop probing properly.
The old code had a fallback that would use a num_ports value of
4 if all the probing methods failed, but that was removed.
This restores the fallback of 4 ports, to get things working
again.
Bump driver version and release date.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make blank functions use proper constant for unblanking.
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Robert Reif <reif@earthlink.net>
Replaced tcx_init_one with tcx_probe.
Fixed some checkpatch problems.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
rose: Wrong list_lock argument in rose_node seqops
netns: Fix reassembly timer to use the right namespace
netns: Fix device renaming for sysfs
bnx2: Update version to 1.7.5.
bnx2: Update RV2P firmware for 5709.
bnx2: Zero out context memory for 5709.
bnx2: Fix register test on 5709.
bnx2: Fix remote PHY initial link state.
bnx2: Refine remote PHY locking.
bridge: forwarding table information for >256 devices
tg3: Update version to 3.92
tg3: Add link state reporting to UMP firmware
tg3: Fix ethtool loopback test for 5761 BX devices
tg3: Fix 5761 NVRAM sizes
tg3: Use constant 500KHz MI clock on adapters with a CPMU
hci_usb.h: fix hard-to-trigger race
dccp: ccid2.c, ccid3.c use clamp(), clamp_t()
net: remove NR_CPUS arrays in net/core/dev.c
net: use get/put_unaligned_* helpers
bluetooth: use get/put_unaligned_* helpers
...
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Bolt in SLB entry for kernel stack on secondary cpus
[POWERPC] PS3: Update ps3_defconfig
[POWERPC] PS3: Remove unsupported wakeup sources
[POWERPC] PS3: Make ps3_virq_setup and ps3_virq_destroy static
[POWERPC] PS3: Add time include to lpm
[POWERPC] Fix slb.c compile warnings
[POWERPC] Xilinx: Fix compile warnings
[POWERPC] Squash build warning for print of resource_size_t in fsl_soc.c
[RAPIDIO] fix current kernel-doc notation
[POWERPC] 86xx: mpc8610_hpcd: add support for PCI Express x8 slot
Fix a potential issue in mpc52xx uart driver
[POWERPC] mpc5200: Allow for fixed speed MII configurations
[POWERPC] 86xx: Fix the wrong serial1 interrupt for 8610 board
The new RV2P firmware fixes 2 issues:
1. The jumbo rx buffer page size is now configurable and set to the
proper PAGE_SIZE. Before, it was assumed to be always 4K.
2. Driver sometimes would crash when receiving jumbo packets mixed
with firmware management packets. This was caused by the old
firmware DMA'ing to the wrong address.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should zero out the context memory for 5709 before each reset. When
we resume after suspend for example, the memory may not be zero and the
chip may not function correctly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register BNX2_CTX_STATUS (0x1004) should be skipped on 5709 as it
contains reserved bits.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some remote PHY blade systems, the driver receives no initial link
interrupt. As a result, the GMII/MII MAC mode does not get setup properly.
To fix this problem, we add an initial poll of the link state after chip
reset.
With this change, the setting of the initial carrier state in the init
code can be eliminated.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2_set_remote_link() should be called under bp->phy_lock to protect
against concurrent polling and interrupt calls. This change is needed
by the next patch which will add one initial poll of the remote PHY
link status.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the version number to 3.92.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All variants of the 5714, 5715, and 5780 offer a feature called the
"Universal Management Port". This feature is implemented in firmware
and is largely transparent to the driver, except...
It turns out that the UMP firmware needs to know the current status
of the link. Because the firmware cannot touch the PHY registers while
the driver is in control of the device, it needs the driver to report
link status changes through an additional handshaking mechanism.
Without this handshake, it has been observed in the field that the UMP
firmware will not operate correctly.
This patch implements the new handshake with the UMP firmware. Since
the handshake uses the same mechanism ASF heartbeats use, code was
added to detect and wait for completion of a pending previous event.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A CPMU related loopback test bug existed for AX revisions of the 5761.
While that errata has been fixed, the CPMU still slows down the core
clock too far to run the loopback test successfully. This patch
disables the CPMU LINK_SPEED mode just like we do with the AX
revisions of the 5761 and all revisions of the 5784.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5761 NVRAM sizes assigned to the nvram_size member are half as big
as they should be. This patch corrects the NVRAM sizes and replaces
the hardcoded constants with preprocessor constants for readability.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MI clock is not configured correctly on adapters with the CPMU
present. The tg3 driver has code which statically sets the MI clock to
be a fraction of the speed at which the core clock is running.
However, the CPMU can change the adapter's core clock frequency based
on operating conditions. Consequently, the MI will run slow when the
core's clock has been slowed down.
There is a new 500KHz constant frequency clock available on adapters
with a CPMU. This patch removes the static core clock scaling and
configures the MI clock to use this new 500KHz clock instead.
Running the MI clock at slower speeds will not directly result in data
corruption, but it does challenge the PHY read and write routine timeouts.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If someone tries to _urb_unlink while _urb_queue_head is running, he'll see
_urb->queue == NULL and fail to do any locking. Prevent that from happening
by strategically placed barriers.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
By changing drivers/power/pmu_battery.c I now have '_' instead of
' ' (spaces) in /sys:
/sys/devices/platform/pmu-battery.0/power_supply/PMU_battery_0
/sys/class/power_supply/PMU_battery_0
I'm still not sure if some userspace tool out there uses the old paths and
will break now.
Signed-off-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This adds init/exit function callbacks to pda_power, to
provide a place where the platform code can request/free
GPIOs that it wants to use in the is_ac_online, is_usb_online
and set_charge functions.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] aic94xx: fix section mismatch
[SCSI] u14-34f: Fix 32bit only problem
[SCSI] dpt_i2o: sysfs code
[SCSI] dpt_i2o: 64 bit support
[SCSI] dpt_i2o: move from virt_to_bus/bus_to_virt to dma_alloc_coherent
[SCSI] dpt_i2o: use standard __init / __exit code
[SCSI] megaraid_sas: fix suspend/resume sections
[SCSI] aacraid: Add Power Management support
[SCSI] aacraid: Fix jbod operations scan issues
[SCSI] aacraid: Fix warning about macro side-effects
[SCSI] add support for variable length extended commands
[SCSI] Let scsi_cmnd->cmnd use request->cmd buffer
[SCSI] bsg: add large command support
[SCSI] aacraid: Fix down_interruptible() to check the return value correctly
[SCSI] megaraid_sas; Update the Version and Changelog
[SCSI] ibmvscsi: Handle non SCSI error status
[SCSI] bug fix for free list handling
[SCSI] ipr: Rename ipr's state scsi host attribute to prevent collisions
[SCSI] megaraid_mbox: fix Dell CERC firmware problem
Fix following warnings:
WARNING: vmlinux.o(.data+0x17aa88): Section mismatch in reference from the variable asd_pcidev_data to the function .devinit.text:asd_aic9410_setup()
WARNING: vmlinux.o(.data+0x17aa98): Section mismatch in reference from the variable asd_pcidev_data to the function .devinit.text:asd_aic9410_setup()
WARNING: vmlinux.o(.data+0x17aaa8): Section mismatch in reference from the variable asd_pcidev_data to the function .devinit.text:asd_aic9405_setup()
asd_pcidev_data is only used by __devinit asd_pci_probe. So mark is const and
annotate it __devinitconst to fix the warnings.
[akpm@linux-foundation.org: fix warning]
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Create a /sys/class/dpt_i2o directory and populate it with
dptiN directories. Each dptiN directory contains a "dev" file
that makes udev create /dev/dptiN
Signed-off-by: Miquel van Smoorenburg <miquels@cistron.nl>
Acked-by: Mark Salyzyn <Mark_Salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is the code to actually support 64 bit platforms. 64 bit
DMA is enabled on both x86_32 PAE and 64 bit platforms.
This code is based in part on the unofficial adaptec 64-bit
dpt_i2o driver update that I got from Mark Salyzyn at Adaptec.
Signed-off-by: Miquel van Smoorenburg <miquels@cistron.nl>
Acked-by: Mark Salyzyn <Mark_Salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove virt_to_bus/bus_to_virt code from dpt_i2o, and use
dma_alloc_coherent() / dma_free_coherent().
This is in preparation of 64-bit support, dma_alloc_coherent()
can allocate memory in the lower 32 bits of physical memory
which is needed because the HBA only supports message blocks under 4GB
This code is based in part on the unofficial adaptec 64-bit
dpt_i2o driver update that I got from Mark Salyzyn at Adaptec.
Signed-off-by: Miquel van Smoorenburg <miquels@cistron.nl>
Acked-by: Mark Salyzyn <Mark_Salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update dpt_i2o.c to use the standard __init / __exit
code instead of the legacy '#include "scsi_module.c"' code.
This is needed in preparation of 64-bit support. scsi_module.c
calls scsi_add_host() with the device pointer set to NULL, and that
crashes code like arch/x64/kernel/pci-gart_64.c::need_iommu().
The reboot_notifier code is deleted because it wasn't compiled
in ever anyway, and it would be useless to duplicate it in
the new code.
Signed-off-by: Miquel van Smoorenburg <miquels@cistron.nl>
Acked-by: Mark Salyzyn <Mark_Salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
megaraid_sas suspend and resume are inappropriatelly placed in
__devinit section. Remove those placements and make the stuff
dependent on CONFIG_PM.
While at it, mark remove function as __devexit.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For firmware that supports the feature(s), add the ability to start or
stop an array using the associated SCSI commands, to automatically
manage the spin-up of an array on new I/O reporting back the
appropriate check conditions and actions in cooperation with the
normal timeout mechanisms and enable the blackout period management in
the Firmware associated with the background spin-down of the arrays
when the Firmware times out and deems the arrays as idle.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As JBOD devices (really just Simple Single Drive Volumes exported to
the SCSI channel) are managed, they fail to update correctly when the
driver triggers a SCSI scan. In addition, the ability to change
multiple arrays or JBODs at the same time was resulting in dropped
scans, set up a mechanism to issue a list of single target scans on a
single configuration change notification from the Firmware.
Performed some additional sundry cosmetic code style cleanups.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
On some compile environments, warnings are produced regarding the
usage of aac_logical_to_phys macro.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (32 commits)
USB GADGET/PERIPHERAL: g_file_storage Bulk-Only Transport compliance, clear-feature ignore
USB GADGET/PERIPHERAL: g_file_storage Bulk-Only Transport compliance
usb_serial: some coding style fixes
USB: Remove redundant dependencies on USB_ATM.
USB: UHCI: disable remote wakeup when it's not needed
USB: OHCI: work around bogus compiler warning
USB: add Cypress c67x00 OTG controller HCD driver
USB: add Cypress c67x00 OTG controller core driver
USB: add Cypress c67x00 low level interface code
USB: airprime: unlock mutex instead of trying to lock it again
USB: storage: Update mailling list address
USB: storage: UNUSUAL_DEVS() for PanDigital Picture frame.
USB: Add the USB 2.0 extension descriptor.
USB: add more FTDI device ids
USB: fix cannot work usb storage when using ohci-sm501
usb: gadget zero timer init fix
usb: gadget zero style fixups (mostly whitespace)
usb serial gadget: CDC ACM fixes
usb: pxa27x_udc driver
USB: INTOVA Pixtreme camera mass storage device
...
Testing on large clusters shows its way too short at 10 secs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove bad BUG_ON() that can trigger in correct operation from
close_con_rpl(). It is possible to get a close_rpl message on a dead
connection. The sequence is:
- host refs ep for close exchange
- host posts close_req
- hw posts PEER_ABORT from incoming RST
- host marks ep DEAD
- host posts ABORT_RPL and releases ep resources
- hw posts CLOSE_RPL
- host derefs ep and ep freed.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Flush the QP only after the HW disables the connection. Currently
we flush the QP when transitioning to CLOSING. This exposes a race
condition where the HW can complete a RECV WR, for instance, -and-
the SW can flush that same WR.
- Only call CQ event handlers on flush IFF we actually flushed something.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Gadget tells controller driver to ignore Clear-Feature(HALT_ENDPOINT)
Signed-off-by: David Lopo <lopo.david@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Given that the bulk of the Kconfig file is enclosed in "if USB_ATM",
remove the unnecessary dependencies.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1084b) fixes the way uhci-hcd handles polling and
remote wakeups for its root hubs. When remote wakeup is disabled,
neither interrupts nor polling should be enabled during a root-hub
suspend. Likewise, if interrupts are enabled during suspend then
polling isn't needed.
Furthermore the EGSM (Enter Global Suspend Mode) bit shouldn't be set
in the Command register unless remote wakeup is enabled. Apparently
some controllers will issue a remote-wakeup interrupt whenever EGSM
is on, even if Resume-Detect interrupts are supposedly disabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch (as1086) works around a bogus "uninitialized variable"
warning generated by some versions of GCC.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds HCD support for the Cypress c67x00 family of devices.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch add the core driver for the c67x00 USB OTG controller. The core
driver is responsible for the platform bus binding and creating either
USB HCD or USB Gadget instances for each of the serial interface engines
on the chip.
This driver does not directly implement the HCD or gadget behaviours; it
just controls access to the chip.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the low level support code for the Cypress c67x00 family of
OTG controllers. The low level code is responsible for register access and
implements the software protocol for communicating with the 16bit
microcontroller inside the c67x00 device.
Communication is done over the HPI interface (16bit SRAM-like parallel bus).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch fixes a [probable] copy & paste mistake in
airprime.c. Instead of unlocking an acquired mutex, the actual
code tries to lock it again.
Signed-off-by: Leonardo Chiquitto <lchiquitto@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/storage/unusual_devs.h lists the address
linux-usb-devel@lists.sourceforge.net for patches to that file. This
address results in a bounce and a pointer to vger. This patch updates
the address in the header file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When I used ohci-sm501, hcd_alloc_coherent() in map_urb_for_dma() is not
called, because usb_sg_init() always sets URB_NO_TRANSFER_DMA_MAP.
dmesg (CONFIG_USB_STORAGE_DEBUG enabled):
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries
usb-storage: Status code -75; transferred 0/36
usb-storage: -- babble
usb-storage: Bulk data transfer result 0x3
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x2
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initialize timer earlier so if an error occurs allocating USB request
or buffer request (zero_bind) Gadget Zero will not hang trying to
delete an uninitialized timer (zero_unbind).
Signed-off-by: David Lopo <lopo.david@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor updates to "Gadget Zero".
- Primarily these are whitespace updates to address the fact that since
this was written, Documentation/CodingStyle was changed to disapprove
of parts of the original coding style.
- Update a few comments that weren't quite correct, notably mentioning
the "autoresume" module parameter.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on a patch from <Aurel.Thomi@ruag.com>, this makes the
CDC-ACM support in the serial gadget handle the SET_LINE_CODING
and SET_CONTROL_LINE_STATE requests ... which should improve
interop with at least MS-Windows "usbser.sys" if not some other
ACM host drivers.
It also adds a few REVISIT comments where this code plays a bit
loose with the CDC ACM spec. If this were used to hook up to a
real RS232 or modem link, those places would need a bit of work.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds pxa27x udc driver to support USB peripherals on pxa27x chips.
The driver is compatible with: Gadget Zero, the File Storage
gadget, and the Ethernet gadget (only in CDC subset mode).
The driver can't properly support multiple interfaces, because
of hardware bugs without possible workaround. That means no
RNDIS support from g_ether, and no CDC ACM support in g_serial.
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
FIX_CAPACITY is all that's needed.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The test for an mos7840_set_uart_reg() error return value only works when
status is signed. propagate its error value.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: SL Baur <steve@xemacs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanup to the "usbtest" driver, mostly to resolve a regression:
all the important diagnostics were at KERN_DEBUG, so that when the
"#define DEBUG" was removed from the top of that file it stopped
providing diagnostics. Fix by using KERN_ERROR. Also:
- Stop using the legacy dbg() calls
- Simplify the internal debug macros
- Correct some test descriptions:
* Test #10 subcase 7 should *always* stall
* Test #10 subcase 8 *may* stall
- Diagnostic about control queue test failures is more informative
- Fix some whitespace "bugs"
And add a warning about the rude interaction between usbfs ioctl()
and khubd during device disconnect ... don't unplug a device under
test, that will wedge.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I hoped to continue to ignore this problem or use libusual, but these
days it's simpler to work around than to deal with it. Let's attempt to
use bad residue devices and hope that upper level integrity checks catch
any problems (e.g. please use sha1sum on your backups).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The wodim says:
"close track/session scsi sendcmd: cmd timeout after 5.000 (480) s"
This happened because we ignored the supplied timeout and used 5s.
It's not completely correct to apply a timeout meant for the complete
command to any single URB, but we don't have many URBs per command, so
this is simple and works.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1088) adds an unusual_devs entry for Samsung's YP-U3.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global onetouch_release_input() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If USB storage is built-in but input subsystem is made modular then
OneTouch button functionality can not be selected.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver has been written from scratch and supports the ISP1760. ISP1761
might (should) work as well but the OTG isn't supported. Also ISO packets are
not. However, it works on my little PowerPC board.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for variable-length, extended, and vendor specific
CDBs to scsi-ml. It is now possible for initiators and ULD's
to issue these types of commands. LLDs need not change much.
All they need is to raise the .max_cmd_len to the longest command
they support (see iscsi patch).
- clean-up some code paths that did not expect commands to be
larger than 16, and change cmd_len members' type to short as
char is not enough.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- struct scsi_cmnd had a 16 bytes command buffer of its own.
This is an unnecessary duplication and copy of request's
cmd. It is probably left overs from the time that scsi_cmnd
could function without a request attached. So clean that up.
- Once above is done, few places, apart from scsi-ml, needed
adjustments due to changing the data type of scsi_cmnd->cmnd.
- Lots of drivers still use MAX_COMMAND_SIZE. So I have left
that #define but equate it to BLK_MAX_CDB. The way I see it
and is reflected in the patch below is.
MAX_COMMAND_SIZE - means: The longest fixed-length (*) SCSI CDB
as per the SCSI standard and is not related
to the implementation.
BLK_MAX_CDB. - The allocated space at the request level
- I have audit all ISA drivers and made sure none use ->cmnd in a DMA
Operation. Same audit was done by Andi Kleen.
(*)fixed-length here means commands that their size can be determined
by their opcode and the CDB does not carry a length specifier, (unlike
the VARIABLE_LENGTH_CMD(0x7f) command). This is actually not exactly
true and the SCSI standard also defines extended commands and
vendor specific commands that can be bigger than 16 bytes. The kernel
will support these using the same infrastructure used for VARLEN CDB's.
So in effect MAX_COMMAND_SIZE means the maximum size command
scsi-ml supports without specifying a cmd_len by ULD's
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
On Apr 21, 2008, at 8:42 PM, Yinghai Lu wrote:
> bisected to:
>
> commit e6990c6448
> Author: Mark Salyzyn <Mark_Salyzyn@adaptec.com>
> Date: Mon Apr 14 14:20:16 2008 -0400
>
> [SCSI] aacraid: Fix down_interruptible() to check the return value
The return value for down_interruptible was incorrectly checked!
updated patch enclosed.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This brings us closer to Real Life, where we'd examine the device
features once it's set the DRIVER_OK status bit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
NR_CPUS (being a host number) is an arbitrary limit for the Guest.
Using the array size directly (which currently happes to be NR_CPUS)
is more futureproof.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rather than faking up some geometry, allow the backend to push the disk
geometry via virtio pci config option. Keep the old geo code around for
compatibility.
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (modified to single struct)
A recent proposed feature addition to the virtio block driver revealed
some flaws in the API: in particular, we assume that feature
negotiation is complete once a driver's probe function returns.
There is nothing in the API to require this, however, and even I
didn't notice when it was violated.
So instead, we require the driver to specify what features it supports
in a table, we can then move the feature negotiation into the virtio
core. The intersection of device and driver features are presented in
a new 'features' bitmap in the struct virtio_device.
Note that this highlights the difference between Linux unsigned-long
bitmaps where each unsigned long is in native endian, and a
straight-forward little-endian array of bytes.
Drivers can still remove feature bits in their probe routine if they
really have to.
API changes:
- dev->config->feature() no longer gets and acks a feature.
- drivers should advertise their features in the 'feature_table' field
- use virtio_has_feature() for extra sanity when checking feature bits
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
A recent proposed feature addition to the virtio block driver revealed
some flaws in the API, in particular how easy it is to break big
endian machines.
The virtio config space was originally chosen to be little-endian,
because we thought the config might be part of the PCI config space
for virtio_pci. It's actually a separate mmio region, so that
argument holds little water; as only x86 is currently using the virtio
mechanism, we can change this (but must do so now, before the
impending s390 merge).
API changes:
- __virtio_config_val() just becomes a striaght vdev->config_get() call.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
So, we previously had a 'VIRTIO_NET_F_GSO' bit which meant that 'the
host can handle csum offload, and any TSO (v4&v6 incl ECN) or UFO
packets you might want to send. I thought this was good enough for
Linux, but it actually isn't, since we don't do UFO in software.
So, add separate feature bits for what the host can handle. Add
equivalent ones for the guest to say what it can handle, because LRO
is coming too (thanks Herbert!).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Herbert tells me that returning NETDEV_TX_BUSY from hard_start_xmit is
seen as a poor thing to do; we should cache the packet and stop the queue.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Do not unregister the major at device remove, since there might be
another device instances around.
(qemu) pci_del 0 11
(qemu) ACPI: PCI interrupt for device 0000:00:0b.0 disabled
(qemu) pci_del 0 10
(qemu) ------------[ cut here ]------------
WARNING: at block/genhd.c:126 unregister_blkdev+0x74/0x9e()
ACPI: PCI interrupt for device 0000:00:0a.0 disabled
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Herbert Xu points out (within another patch) that my scatterlists are
too short: one entry for the gso header, one for the skb->data, and
MAX_SKB_FRAGS for all the fragments.
Fix both xmit and recv sides (recv currently unused, coming in later
patch).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Ron Minnich points out that a struct containing a char is not always
sizeof(char); simplest to remove the structure to avoid confusion.
Cc: "ron minnich" <rminnich@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
get_buf() gives the length written by the other side, which will be
zero. We want to add the skb length.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
A corrupt virtqueue (caused by the other end screwing up) can have
strange results such as a driver spinning: just bail when we try to
get a buffer from a known-broken queue.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Other OS wakeup is not supported from the IR controller,
the bluetooth controller nor the RTC. Remove references
to these in the PS3 sys-manager source.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add an include <asm/time.h> statement for get_tb().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/sysdev/xilinx_intc.c: In function 'xilinx_intc_init':
arch/powerpc/sysdev/xilinx_intc.c:111: warning: format '%08X' expects type 'unsigned int', but argument 2 has type 'resource_size_t'
drivers/char/xilinx_hwicap/xilinx_hwicap.c: In function 'hwicap_setup':
drivers/char/xilinx_hwicap/xilinx_hwicap.c:626: warning: cast to pointer from integer of different size
drivers/char/xilinx_hwicap/xilinx_hwicap.c:646: warning: format '%x' expects type 'unsigned int', but argument 6 has type 'resource_size_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There was an obvious typo in LED structure
initialization which caused the radio and quality/activity
leds to be incorrectly initialized which resulted in
the leds not being enabled.
Additionally add the rt2x00led_led_activity() handler
that will enable TX/RX activity leds when the radio
is being enabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The timing settings for 1MBs should exclude
the short preamble bit since that only applies
to 2MBs, 5.5MBs and 11MBs.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
direct_mask will be set when we are not associated and requesting a
direct scan. The second debug print will be confusing as priv->essid
is not set at that time and it will thus print "<hidden>" while it is
known to which AP a direct scan is requested - as previous debug message
also indicates.
Now make all debugging consistent.
Signed-off-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All channels should be scanned, including the current channel
when the client is associated.
Removed also unused flag to scan only active channels.
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some TX/RX related locking issues.
With this patch applied, some of the PHY transmission errors are fixed.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: fw-sbp2: log scsi_target ID at release
ieee1394: fix NULL pointer dereference in sysfs access
mpc52xx_uart_int and __uart_put_char both try to acquire the
port->lock. Therefore the function sequence of:
mpc52xx_uart_int--> ...-->flush_to_ldisc-->...-->__uart_put_char
can potentially trigger a deadlock. To avoid this deadlock a fix
similar to that found in the 8250.c serial driver is applied. The
deadlock is avoided by releasing the lock before pushing a buffer
and reacquiring it when completed.
Signed-off-by: Andrew Liu <shengping.liu@windriver.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Adding the ability to get a physical address from point() in addition
to virtual address. This physical address is required for XIP of
userspace code from flash.
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Reviewed-by: Jörn Engel <joern@logfs.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Regression since "ieee1394: prevent device binding of raw1394,
video1394, dv1394", commit d2ace29fa4:
$ cat /sys/bus/ieee1394/drivers/raw1394/device_ids
triggers a NULL pointer dereference in fw_show_drv_device_ids.
Reported by Miles Lane.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Miles Lane <miles.lane@gmail.com>
Various improvements for configuring the MPC5200 MII link from the
device tree:
* Look for 'current-speed' property for fixed speed MII links
* Look for 'fsl,7-wire-mode' property for boards using the 7 wire mode
* move definition of private data structure out of the header file
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
hwmon: (adt7473) minor cleanup / refactoring
hwmon: (asb100) Remove some dead code
hwmon: (lm75) Fix an incorrect comment
hwmon: (w83793) VID and VRM handling cleanups
hwmon: (w83l785ts) Don't ask the user to report failures
hwmon: (smsc47b397) add a new chip id (0x8c)
It's easy: grab locks before talking to hardware and realease
them afterwards. The one big lock has been splitted into a hw_lock
and mii_lock.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
linux-2.6-mk68/drivers/net/fec.c: In function 'fec_enet_module_init':
linux-2.6-mk68/drivers/net/fec.c:2627: warning: unused variable 'j'
linux-2.6-mk68/drivers/net/fec.c: At top level:
linux-2.6-mk68/drivers/net/fec.c:2136: warning: 'mii_link_interrupt' defined but not used
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the acquisition of unused interrupt types. We don't need to
register all the TX and RX varients used on some ColdFire FEC hardware.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Renamed the 5272 hash_table registers to match the "grp" hash_table
registers of the other ColdFire parts. They are actually a group hash.
The makes for consistent setup across all ColdFire parts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/scsi/mvsas.c: In function `mvs_update_phyinfo':
drivers/scsi/mvsas.c:2822: warning: long long unsigned int format, u64 arg (arg 5)
drivers/scsi/mvsas.c:2822: warning: long long unsigned int format, u64 arg (arg 6)
We do not know what type the arch uses to implement u64.
Cc: Ke Wei <kewei@marvell.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/scsi/ncr53c8xx.c: In function 'process_waiting_list':
drivers/scsi/ncr53c8xx.c:8225: warning: suggest parentheses around assignment used as truth value
recently added by
commit 172c122df5
Author: Harvey Harrison <harvey.harrison@gmail.com>
Date: Mon Apr 28 16:50:03 2008 -0700
scsi: fix integer as NULL pointer warnings
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Repair the effects of
commit 55da77899c
Author: Alan Cox <alan@lxorguk.ukuu.org.uk>
Date: Wed Apr 30 00:54:07 2008 -0700
synclink series: switch to int put_char method
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
drivers/char/synclink_gt.c: In function 'put_char':
drivers/char/synclink_gt.c:919: warning: 'ret' may be used uninitialized in this function
and do some whitespace repair and unneeded-cast-removal in there as well.
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simply replace proc_create and further data assigned with proc_create_data.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Alexey Dobriyan <adobriyan@openvz.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for pca9555 I2C I/O expander. As the comment suggests this part
is software compatible with the pca9539.
Signed-off-by: Will Newton <will.newton@imgtec.com>
Cc: "eric miao" <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Fri, Apr 18, 2008 at 09:08:55PM +0200, Julia Lawall wrote:
> I found 63 occurrences of this problem with the following semantic match
> (http://www.emn.fr/x-info/coccinelle/):
>
> @@ unsigned int i; @@
>
> * i < 0
>
Since this one's always in the range 0-255, it could probably be made
signed, but it's just as easy to make it work unsigned.
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use PIO for full-duplex transfers, instead of DMA.
Signed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add new PCI Express Neo/JSM board to the supported list of drivers in
the JSM driver.
Signed-off-by: Scott Kilau <scottk@digi.com>
Acked-by: Ananda V <avenkat@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i8k driver multiplies the fan speed reported by the BIOS with a factor of
30. On my Dell Latitude D800, this factor is not required.
I'd suggest to make this configurable.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
next-20080430/drivers/pnp/pnpbios/rsparser.c:594: warning: format '%d' expects type 'int', but argument 4 has type 'resource_size_t'
next-20080430/drivers/pnp/pnpbios/rsparser.c:605: warning: format '%d' expects type 'int', but argument 4 has type 'resource_size_t'
[joe@perches.com: fix it]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alchemy Semi Au1000 pcmcia driver: The semaphore pcmcia_sockets_lock
is used as a mutex, convert it to the mutex API
(akpm: make it static too)
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cb_alloc() uses a function (pci_scan_slot) that will be annotated __devinit.
Annotate cb_alloc() with __ref to tell modpost to ignore this reference.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Silence following warnings:
WARNING: drivers/pcmcia/built-in.o(.data+0x14e0): Section mismatch in reference from the variable pd6729_pci_drv to the function .devinit.text:pd6729_pci_probe()
WARNING: drivers/pcmcia/built-in.o(.data+0x14e8): Section mismatch in reference from the variable pd6729_pci_drv to the function .devexit.text:pd6729_pci_remove()
WARNING: drivers/pcmcia/built-in.o(.data+0x16c0): Section mismatch in reference from the variable i82092aa_pci_drv to the function .devinit.text:i82092aa_pci_probe()
WARNING: drivers/pcmcia/built-in.o(.data+0x16c8): Section mismatch in reference from the variable i82092aa_pci_drv to the function .devexit.text:i82092aa_pci_remove()
Rename the variables from *_drv to *_driver so modpost ignore the OK
references to __devinit/__devexit functions.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Silence the following warnings:
WARNING: drivers/pcmcia/built-in.o(.data+0x6e8): Section mismatch in reference from the variable pcmcia_bus_interface to the function .devinit.text:pcmcia_bus_add_socket()
WARNING: drivers/pcmcia/built-in.o(.data+0xa88): Section mismatch in reference from the variable pccard_rsrc_interface to the function .devinit.text:pccard_sysfs_add_rsrc()
WARNING: drivers/pcmcia/built-in.o(.data+0xa90): Section mismatch in reference from the variable pccard_rsrc_interface to the function .devexit.text:pccard_sysfs_remove_rsrc()
The variables of type class_interface contains references
to __devinit and __devexit functions which is OK.
Silence warnings by annotating the variables with __refdata.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86.git randconfig testing found the following build error in latest
-git:
CC [M] drivers/isdn/hysdn/hysdn_procconf.o
CC [M] drivers/isdn/hysdn/hysdn_init.o
drivers/isdn/hysdn/hysdn_procconf.c: In function 'hysdn_procconf_init':
drivers/isdn/hysdn/hysdn_procconf.c:408: error: too few arguments to function 'proc_create'
with the following config:
http://redhat.com/~mingo/misc/config-Wed_Apr_30_15_12_48_CEST_2008.bad
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: "Denis V. Lunev" <den@openvz.org>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86 is the only arch right now, which provides an optimized for
div_long_long_rem and it has the downside that one has to be very careful that
the divide doesn't overflow.
The API is a little akward, as the arguments for the unsigned divide are
signed. The signed version also doesn't handle a negative divisor and
produces worse code on 64bit archs.
There is little incentive to keep this API alive, so this converts the few
users to the new API.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Thursday 01 May 2008, Jeremy Kerr wrote:
> Hi all,
>
> On QS20 Cell machines, Linus' current git tree explodes on boot:
>
> SiI680: IDE controller (0x1095:0x0680 rev 0x02) at PCI slot
> 0000:00:0a.0
> SiI680: BASE CLOCK == 133
> SiI680: 100% native mode on irq 51
> ide0: MMIO-DMA
> ide1: MMIO-DMA
> Unable to handle kernel paging request for data at address
> 0xa000100081220080
> Faulting instruction address: 0xc000000000024748
> cpu 0x2: Vector: 300 (Data Access) at [c00000001e143420]
> pc: c000000000024748: ._insw_ns+0x10/0x30
> lr: c000000000037fc4: .spiderpci_readsw+0x24/0x6c
> sp: c00000001e1436a0
> msr: 9000000000001032
> dar: a000100081220080
> dsisr: 40000000
> current = 0xc00000003d060000
> paca = 0xc000000000623880
> pid = 1, comm = swapper
> enter ? for help
> [link register ] c000000000037fc4 .spiderpci_readsw+0x24/0x6c
> [c00000001e1436a0] c00000000062ce63 (unreliable)
> [c00000001e143730] c0000000000379d4 .iowa_readsw+0x78/0xa8
> [c00000001e1437c0] c000000000037a98 .iowa_insw+0x94/0xd4
> [c00000001e143850] c00000000022a190 .ata_input_data+0x298/0x2ec
> [c00000001e143910] c00000000022b600 .try_to_identify+0x2c0/0x6d4
> [c00000001e1439d0] c00000000022bb54 .do_probe+0x140/0x35c
> [c00000001e143a80] c00000000022bfbc .ide_probe_port+0x24c/0x670
> [c00000001e143b50] c00000000022d09c .ide_device_add_all+0x2ec/0x690
> [c00000001e143c00] c00000000022d4a4 .ide_device_add+0x64/0x74
> [c00000001e143c90] c00000000022f834 .ide_setup_pci_device+0x58/0x7c
> [c00000001e143d30] c00000000038bdf8
> [c00000001e143e10] c000000000486fb0 .ide_scan_pcibus+0x8c/0x178
> [c00000001e143ea0] c000000000460c00 .kernel_init+0x1c4/0x344
> [c00000001e143f90] c000000000024a1c .kernel_thread+0x4c/0x68
>
> It looks like we're trying to do PIO accesses (which appear to be
> broken, but that's another issue) to this MMIO device. In
> ata_input_data, we see that:
>
> u8 mmio = (hwif->host_flags & IDE_HFLAG_MMIO) ? 1 : 0;
>
> Gives mmio == 0.
>
> (what's the difference between hwif->mmio and ID_HFLAG_MMIO?)
>
> In the siimage driver, hwif->host flags is initially set up correctly
> (host_flags includes IDE_HFLAG_MMIO), but we then *clear* this bit in
> ide_init_port:
>
> hwif->host_flags = d->host_flags;
>
> where d is the struct ide_port_info for this chipset. In my case,
> d->host_flags is 0x0. It looks like this will be the same for all of
> the siimage chipsets.
Don't over-write hwif->host_flags in ide_init_port(), some host drivers
set IDE_HFLAG_MMIO or IDE_HFLAG_NO_IO_32BIT host flag early.
Thanks to Jeremy Kerr for the excellent analysis of the bug.
Reported-by: Jeremy Kerr <jk@ozlabs.org>
Tested-by: Jeremy Kerr <jk@ozlabs.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Commit f56bcd80 ("IPoIB: Use separate CQ for UD send completions")
introduced a bug where the transmit queue could get stopped and never
woken up. The problem is that send completions are only polled at the
end of the xmit function, so if the send queue fills up and the xmit
path stops the queue, then there is no way for send completions to
ever get polled, and so the transmit queue stays stopped forever.
Fix this by arming the send CQ just before posting the last send
request that fills the send queue. Then, when the completion event
handler is called, drain the send CQ. Since it is possible that not
enough send completions are in the CQ, verify that the the net queue
has been woken up after draining the send CQ, and if not arm a timer
and drain again at the timer function.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When I merged bbf8eed1 ("IB/mlx4: Add support for resizing CQs") I
changed things around so that mlx4_ib_alloc_cq_buf() and
mlx4_ib_free_cq_buf() were used everywhere they could be. However, I
screwed up the number of entries passed into mlx4_ib_alloc_cq_buf()
in a couple places -- the function bumps the number of entries
internally, so the caller shouldn't add 1 as well.
Passing a too-big value for the number of entries to mlx4_ib_free_cq_buf()
can cause the cleanup to go off the end of an array and corrupt
allocator state in interesting ways.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-fixes3: (21 commits)
x86: numaq fix
x86: 8K stacks by default
x86: ioremap ram check fix
x86: fix HT cpu booting on 32-bit
x86: optimize inlining off
x86: CONFIG_X86_ELAN fix
x86: Kconfig fix
x86 PAT: fix performance drop for glx, use UC minus for ioremap(), ioremap_nocache() and pci_mmap_page_range()
x86: use defconfigs from x86/configs/*
toshiba: use ioremap_cached
revert: "x86: ioremap(), extend check to all RAM pages"
x86: don't bother printing compat vdso address
fix: x86: support for new UV apic
x86: fix early-BUG message
x86: iommu_sac_force can become static
x86: add proper header for reboot_force
x86 VISWS: build fix
x86, voyager: fix ioremap_nocache()
hpet: fix
x86: unexport kmap_atomic_to_page
...
According to Coverity (kudo's to Adrian Bunk), we had one use-before-check
bug in libe libertas driver. This patch fixes this issue.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes operation of dual-PHY (A/B/G) devices.
Do not anounce the A-PHY to mac80211, as that's not supported, yet.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
klist: fix coding style errors in klist.h and klist.c
driver core: remove no longer used "struct class_device"
pcmcia: remove pccard_sysfs_interface warnings
devres: support addresses greater than an unsigned long via dev_ioremap
kobject: do not copy vargs, just pass them around
sysfs: sysfs_update_group stub for CONFIG_SYSFS=n
DEBUGFS: Correct location of debugfs API documentation.
driver core: warn about duplicate driver names on the same bus
klist: implement klist_add_{after|before}()
klist: implement KLIST_INIT() and DEFINE_KLIST()
sysfs: Disallow truncation of files in sysfs
Make the PCMCIA core stop using class_interface to hide socket attribute
registration. This removes the associated section mismatch warnings, and
helps get to the point where that mechanism can finally be removed.
Simplify that attribute registration by using an attribute_group.
This is a net shrink in object size.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently an attempt to register multiple
drivers with the same name causes the
stack trace with some cryptic error message.
The attached patch adds the necessary check
and the clear error message.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
acpi_device_dir() is NULL until all files are createst, so everyting is
created in straight in /proc/ and creation code warns.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The switch of ioremap to default to uncached doesn't break this driver
but it does needlessly slow it down as BIOS space is cachable and this
driver is quite happy scanning cached ROM space.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (179 commits)
ACPI: Fix acpi_processor_idle and idle= boot parameters interaction
acpi: fix section mismatch warning in pnpacpi
intel_menlo: fix build warning
ACPI: Cleanup: Remove unneeded, multiple local dummy variables
ACPI: video - fix permissions on some proc entries
ACPI: video - properly handle errors when registering proc elements
ACPI: video - do not store invalid entries in attached_array list
ACPI: re-name acpi_pm_ops to acpi_suspend_ops
ACER_WMI/ASUS_LAPTOP: fix build bug
thinkpad_acpi: fix possible NULL pointer dereference if kstrdup failed
ACPI: check a return value correctly in acpi_power_get_context()
#if 0 acpi/bay.c:eject_removable_drive()
eeepc-laptop: add hwmon fan control
eeepc-laptop: add backlight
eeepc-laptop: add base driver
ACPI: thinkpad-acpi: bump up version to 0.20
ACPI: thinkpad-acpi: fix selects in Kconfig
ACPI: thinkpad-acpi: use a private workqueue
ACPI: thinkpad-acpi: fluff really minor fix
ACPI: thinkpad-acpi: use uppercase for "LED" on user documentation
...
Fixed conflicts in drivers/acpi/video.c and drivers/misc/intel_menlow.c
manually.
acpi_processor_idle and "idle=" boot parameter interaction is broken.
The problem is that, at boot time acpi driver is checking for "idle=" boot
option and not registering the acpi idle handler. But, when there is a CST
changed callback (typically when switching AC <-> battery or suspend-resume)
there are no checks for boot_option_idle_override and acpi idle handler tries
to get installed with nasty side effects.
With CPU_IDLE configured this issue causes results in a nasty oops on CST
change callback and without CPU_IDLE there is no oops, but boot option
of "idle=" gets ignored and acpi idle handler gets installed.
Change the behavior to not do anything in acpi idle handler when there is a
"idle=" boot option.
Note that the problem is only there when "idle=" boot option is used.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix following section mismatch warning:
WARNING: vmlinux.o(.text+0x153d69): Section mismatch in reference from the function is_exclusive_device() to the variable .init.data:excluded_id_list
is_exclusive_device is only used from __init context so document
this with the __init annotation and get rid of the warning.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (53 commits)
tcp: Overflow bug in Vegas
[IPv4] UFO: prevent generation of chained skb destined to UFO device
iwlwifi: move the selects to the tristate drivers
ipv4: annotate a few functions __init in ipconfig.c
atm: ambassador: vcc_sf semaphore to mutex
MAINTAINERS: The socketcan-core list is subscribers-only.
netfilter: nf_conntrack: padding breaks conntrack hash on ARM
ipv4: Update MTU to all related cache entries in ip_rt_frag_needed()
sch_sfq: use del_timer_sync() in sfq_destroy()
net: Add compat support for getsockopt (MCAST_MSFILTER)
net: Several cleanups for the setsockopt compat support.
ipvs: fix oops in backup for fwmark conn templates
bridge: kernel panic when unloading bridge module
bridge: fix error handling in br_add_if()
netfilter: {nfnetlink,ip,ip6}_queue: fix skb_over_panic when enlarging packets
netfilter: x_tables: fix net namespace leak when reading /proc/net/xxx_tables_names
netfilter: xt_TCPOPTSTRIP: signed tcphoff for ipv6_skip_exthdr() retval
tcp: Limit cwnd growth when deferring for GSO
tcp: Allow send-limited cwnd to grow up to max_burst when gso disabled
[netdrvr] gianfar: Determine TBIPA value dynamically
...
x86.git randconfig testing found a build failure on latest -git:
drivers/built-in.o: In function `set_type':
tuner-core.c:(.text+0x2a9a26): undefined reference to `tea5761_attach'
tuner-core.c:(.text+0x2a9d05): undefined reference to `tda9887_attach'
tuner-core.c:(.text+0x2a9d51): undefined reference to `xc2028_attach'
tuner-core.c:(.text+0x2a9e22): undefined reference to `tda829x_attach'
tuner-core.c:(.text+0x2a9e3f): undefined reference to `microtune_attach'
drivers/built-in.o: In function `tuner_probe':
tuner-core.c:(.text+0x2aa18a): undefined reference to `tda829x_probe'
tuner-core.c:(.text+0x2aa302): undefined reference to `tea5761_autodetection'
with the following config:
http://redhat.com/~mingo/misc/config-Wed_Apr_30_10_21_40_CEST_2008.bad
the problem is caused by the drivers/media/common/tuners/ subdirectory
not being part of the kbuild hierarchy anymore, due to commit
7c91f0624 ("V4L/DVB(7767): Move tuners to common/tuners").
this seems similar to the problem also reported by Mike Galbraith.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds partition management for Block RAM Device (BRD).
This patch is done to keep in sync BRD and loop device drivers.
This patch adds a parameter to the module, max_part, to specify
the maximum number of partitions per RAM device.
Example:
# modprobe brd max_part=63
# ls -l /dev/ram*
brw-rw---- 1 root disk 1, 0 2008-04-03 13:39 /dev/ram0
brw-rw---- 1 root disk 1, 64 2008-04-03 13:39 /dev/ram1
brw-rw---- 1 root disk 1, 640 2008-04-03 13:39 /dev/ram10
brw-rw---- 1 root disk 1, 704 2008-04-03 13:39 /dev/ram11
brw-rw---- 1 root disk 1, 768 2008-04-03 13:39 /dev/ram12
brw-rw---- 1 root disk 1, 832 2008-04-03 13:39 /dev/ram13
brw-rw---- 1 root disk 1, 896 2008-04-03 13:39 /dev/ram14
brw-rw---- 1 root disk 1, 960 2008-04-03 13:39 /dev/ram15
brw-rw---- 1 root disk 1, 128 2008-04-03 13:39 /dev/ram2
brw-rw---- 1 root disk 1, 192 2008-04-03 13:39 /dev/ram3
brw-rw---- 1 root disk 1, 256 2008-04-03 13:39 /dev/ram4
brw-rw---- 1 root disk 1, 320 2008-04-03 13:39 /dev/ram5
brw-rw---- 1 root disk 1, 384 2008-04-03 13:39 /dev/ram6
brw-rw---- 1 root disk 1, 448 2008-04-03 13:39 /dev/ram7
brw-rw---- 1 root disk 1, 512 2008-04-03 13:39 /dev/ram8
brw-rw---- 1 root disk 1, 576 2008-04-03 13:39 /dev/ram9
# fdisk /dev/ram0
Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel
Building a new DOS disklabel. Changes will remain in memory only,
until you decide to write them. After that, of course, the previous
content won't be recoverable.
Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite)
Command (m for help): o
Building a new DOS disklabel. Changes will remain in memory only,
until you decide to write them. After that, of course, the previous
content won't be recoverable.
Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite)
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 1
First cylinder (1-2, default 1): 1
Last cylinder or +size or +sizeM or +sizeK (1-2, default 2): 2
Command (m for help): w
The partition table has been altered!
Calling ioctl() to re-read partition table.
Syncing disks.
# ls -l /dev/ram0*
brw-rw---- 1 root disk 1, 0 2008-04-03 13:40 /dev/ram0
brw-rw---- 1 root disk 1, 1 2008-04-03 13:40 /dev/ram0p1
# mkfs /dev/ram0p1
mke2fs 1.40-WIP (14-Nov-2006)
Filesystem label=
OS type: Linux
Block size=1024 (log=0)
Fragment size=1024 (log=0)
4016 inodes, 16032 blocks
801 blocks (5.00%) reserved for the super user
First data block=1
Maximum filesystem blocks=16515072
2 block groups
8192 blocks per group, 8192 fragments per group
2008 inodes per group
Superblock backups stored on blocks:
8193
Writing inode tables: done
Writing superblocks and filesystem accounting information: done
This filesystem will be automatically checked every 26 mounts or
180 days, whichever comes first. Use tune2fs -c or -i to override.
# mount /dev/ram0p1 /mnt
df /mnt
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/ram0p1 15521 138 14582 1% /mnt
# ls -l /mnt
total 12
drwx------ 2 root root 12288 2008-04-03 13:41 lost+found
# umount /mnt
# rmmod brd
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add calls to the generic object debugging infrastructure and provide fixup
functions which allow to keep the system alive when recoverable problems have
been detected by the object debugging core code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Greg KH <greg@kroah.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also, change the variable names used in the min/max macros to avoid shadowed
variable warnings when min/max min_t/max_t are nested.
Small formatting changes to make all the macros have a similar form.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix v4l build]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a minimalistic braille screen reader support. This is meant to
be used by blind people e.g. on boot failures or when / cannot be mounted
etc and thus the userland screen readers can not work.
[akpm@linux-foundation.org: fix exports]
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Jiri Kosina <jikos@jikos.cz>
Cc: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fuse will use temporary buffers to write back dirty data from memory mappings
(normal writes are done synchronously). This is needed, because there cannot
be any guarantee about the time in which a write will complete.
By using temporary buffers, from the MM's point if view the page is written
back immediately. If the writeout was due to memory pressure, this
effectively migrates data from a full zone to a less full zone.
This patch adds a new counter (NR_WRITEBACK_TEMP) for the number of pages used
as temporary buffers.
[Lee.Schermerhorn@hp.com: add vmstat_text for NR_WRITEBACK_TEMP]
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Factor out the code used to allocate/free a pts index into new interfaces,
devpts_new_index() and devpts_kill_index(). This localizes the external data
structures used in managing the pts indices.
[akpm@linux-foundation.org: undo accidental mutex2sem conversion]
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Have ptmx_open() propagate any error code returned by devpts_pty_new()
(which returns either 0 or -ENOMEM anyway).
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At ptmx_open(), the 2nd parameter for check_tty_count() should
be "ptmx_open".
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simple search/replace except for synclink.c where I noticed a real bug and
fixed it too. It was doing NULL + offset, then checking for NULL if the remap
failed.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Something Arjan suggested which allows us to clean up the code nicely
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the rather strange buffer management on open that turned up while auditing
for BKL dependencies.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use the tty baud functions
- Call driver termios methods directly holding the right locking
- Check for a write method
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Operations are now a shared const function block as with most other Linux
objects
- Introduce wrappers for some optional functions to get consistent behaviour
- Wrap put_char which used to be patched by the tty layer
- Document which functions are needed/optional
- Make put_char report success/fail
- Cache the driver->ops pointer in the tty as tty->ops
- Remove various surplus lock calls we no longer need
- Remove proc_write method as noted by Alexey Dobriyan
- Introduce some missing sanity checks where certain driver/ldisc
combinations would oops as they didn't check needed methods were present
[akpm@linux-foundation.org: fix fs/compat_ioctl.c build]
[akpm@linux-foundation.org: fix isicom]
[akpm@linux-foundation.org: fix arch/ia64/hp/sim/simserial.c build]
[akpm@linux-foundation.org: fix kgdb]
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver somehow escaped the tty operations changes way back when. Update
it so that we can switch to tty->ops shortly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We are about to change the tty layer to avoid keeping private copies of all
the methods in each tty. We have to update the pty layer first as it
currently patches the ioctl method according to the tty type. Use multiple
tty operations sets instead.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Put the changes into the drivers first. This will still compile/work but
produce a warning if bisected so can still be debugged
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Stop drivers calling their own flush method indirectly, it obfuscates code
and it will change soon anyway
- A few more lock_kernel paths temporarily needed in some driver internal
waiting code
- Remove private put_char method that does a write call for one char - we
have that anyway
- Most but not yet all of the termios copy under lock fixing (some has other
dependencies to follow)
- Note a few locking bugs in drivers found in the process
- Kill remaining [ab]users of TIOCG/SSOFTCAR in the driver, these must go to
fix the termios locking
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.
A simplified version of the semantic patch making this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@ change_compare_np @
expression E;
@@
(
- jiffies <= E
+ time_before_eq(jiffies,E)
|
- jiffies >= E
+ time_after_eq(jiffies,E)
|
- jiffies < E
+ time_before(jiffies,E)
|
- jiffies > E
+ time_after(jiffies,E)
)
@ include depends on change_compare_np @
@@
#include <linux/jiffies.h>
@ no_include depends on !include && change_compare_np @
@@
#include <linux/...>
+ #include <linux/jiffies.h>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename defines to be in RIO* namespace to not to collide with other defines in
tree. This broke (as akpm correctly pointed out) some allmodconfig builds,
e.g. on ppc:
In file included from drivers/char/rio/rio_linux.c:81:
drivers/char/rio/cirrus.h:202:1: warning: "COMPLETE" redefined
In file included from include/net/netns/ipv4.h:8,
from include/net/net_namespace.h:13,
from include/linux/seq_file.h:7,
from include/asm/machdep.h:12,
from include/asm/pci.h:17,
from include/linux/pci.h:951,
from drivers/char/rio/rio_linux.c:50:
include/net/inet_frag.h:28:1: warning: this is the location of the previous definition
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is handled (and correctly) by the core code so does not belong
incorrectly in the driver.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- remove i2os.h -- there was only macro to macro renaming or useless
stuff
- remove another uselless stuf (NULLFUNC, NULLPTR, YES, NO)
- use outb/inb directly
- use locking functions directly
- don't define another ROUNDUP, use roundup(x, 2) instead
- some comments and whitespace cleanup
- remove some commented crap
- prepend the rest by I2 prefix to not collide with rest of the world
like in following output (pointed out by akpm)
In file included from drivers/char/ip2/ip2main.c:128:
drivers/char/ip2/i2ellis.h:608:1: warning: "COMPLETE" redefined
In file included from include/net/netns/ipv4.h:8,
from include/net/net_namespace.h:13,
from include/linux/seq_file.h:7,
from include/asm/machdep.h:12,
from include/asm/pci.h:17,
from include/linux/pci.h:951,
from drivers/char/ip2/ip2main.c:95:
include/net/inet_frag.h:28:1: warning: this is the location of the previous definition
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace init_module and cleanup_module with static functions and
module_init/module_exit.
Signed-off-by: Jon Schindler <jkschind@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/char/epca.c:926:28: warning: Using plain integer as NULL pointer
drivers/char/epca.c:1841:2: warning: Using plain integer as NULL pointer
Forward declarations were already marked static, mark the definitions too.
drivers/char/epca.c:2493:6: warning: symbol 'digi_send_break' was not declared. Should it be static?
drivers/char/epca.c:2881:12: warning: symbol 'init_PCI' was not declared. Should it be static?
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nested min() macros.
drivers/char/cyclades.c:2750:7: warning: symbol '_x' shadows an earlier one
drivers/char/cyclades.c:2750:7: originally declared here
drivers/char/cyclades.c:2750:7: warning: symbol '_x' shadows an earlier one
drivers/char/cyclades.c:2750:7: originally declared here
drivers/char/cyclades.c:2750:7: warning: symbol '_y' shadows an earlier one
drivers/char/cyclades.c:2750:7: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nested min() macros shadow _x, separate into two lines.
drivers/char/rocket.c:451:7: warning: symbol '_x' shadows an earlier one
drivers/char/rocket.c:451:7: originally declared here
drivers/char/rocket.c:451:7: warning: symbol '_x' shadows an earlier one
drivers/char/rocket.c:451:7: originally declared here
drivers/char/rocket.c:451:7: warning: symbol '_y' shadows an earlier one
drivers/char/rocket.c:451:7: originally declared here
drivers/char/rocket.c:1754:7: warning: symbol '_x' shadows an earlier one
drivers/char/rocket.c:1754:7: originally declared here
drivers/char/rocket.c:1754:7: warning: symbol '_x' shadows an earlier one
drivers/char/rocket.c:1754:7: originally declared here
drivers/char/rocket.c:1754:7: warning: symbol '_y' shadows an earlier one
drivers/char/rocket.c:1754:7: originally declared here
drivers/char/rocket.c:1751:20: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hitting either of the break statements in the while loop would cause a
double-unlock of info->lock.
[Jiri Slaby suggested simply returning is safe here, rather than a goto]
Noticed by sparse:
drivers/char/esp.c:2042:2: warning: context imbalance in 'rs_wait_until_sent' - unexpected unlock
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
flags only use was in spin_lock_irqsave/spin_lock_irgrestore pairs, no
need to redeclare for each one.
drivers/char/esp.c:1599:17: warning: symbol 'flags' shadows an earlier one
drivers/char/esp.c:1517:16: originally declared here
drivers/char/esp.c:1615:17: warning: symbol 'flags' shadows an earlier one
drivers/char/esp.c:1517:16: originally declared here
drivers/char/esp.c:1631:17: warning: symbol 'flags' shadows an earlier one
drivers/char/esp.c:1517:16: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Be more verbose on fw load fail as noted by Oyvind.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Oyvind Aabling <Oyvind.Aabling@uni-c.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop a message to dmesg about card being ready.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Tested-by: Oyvind Aabling <Oyvind.Aabling@uni-c.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It allows to simplify the code, especially MoxaPortSetBaud.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Tested-by: Oyvind Aabling <Oyvind.Aabling@uni-c.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- moxa_flush_chars -- no code; ldics handle this well
- moxa_put_char -- only wrapper to moxa_write (same code), tty does this
the same way if tty->driver->put_char is NULL
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Tested-by: Oyvind Aabling <Oyvind.Aabling@uni-c.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- add locking to open/close/hangup and ioctl (tiocm)
- add pci hot-un-plug support (hangup on board remove, wait for openers)
- cleanup block_till_ready
- move close code common to close/hangup into separate function to be
able to call it from open when hangup occurs while block_till_ready
- let ldisc flush on tty layer, it will do it after we return
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Tested-by: Oyvind Aabling <Oyvind.Aabling@uni-c.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- del timer after we are sure it won't be fired again
- make timer scheduling atomic
- don't reschedule timer when all cards have gone
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Tested-by: Oyvind Aabling <Oyvind.Aabling@uni-c.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- merge 2 timers into one -- one can handle the emptywait as good as the other
- merge 2 separated poll functions into one, this allows handle the actions
directly and simplifies the code
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Tested-by: Oyvind Aabling <Oyvind.Aabling@uni-c.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- allow stats only for sys_admin
- move TCSBRK* processing to .break_ctl tty op
- let TIOCGSOFTCAR and TIOCSSOFTCAR be processed by ldisc
- remove MOXA_GET_MAJOR, MOXA_GET_CUMAJOR
- fix jiffies subtraction by time_after
- move moxa ioctl numbers into the header; still not exported to userspace,
needs _IOC and 32/64 compat cleanup anyways
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Tested-by: Oyvind Aabling <Oyvind.Aabling@uni-c.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
